summaryrefslogtreecommitdiffstats
path: root/drivers/bluetooth
AgeCommit message (Collapse)AuthorFilesLines
2023-01-17Bluetooth: hci_qca: Fix driver shutdown on closed serdevKrzysztof Kozlowski1-0/+7
The driver shutdown callback (which sends EDL_SOC_RESET to the device over serdev) should not be invoked when HCI device is not open (e.g. if hci_dev_open_sync() failed), because the serdev and its TTY are not open either. Also skip this step if device is powered off (qca_power_shutdown()). The shutdown callback causes use-after-free during system reboot with Qualcomm Atheros Bluetooth: Unable to handle kernel paging request at virtual address 0072662f67726fd7 ... CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W 6.1.0-rt5-00325-g8a5f56bcfcca #8 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: tty_driver_flush_buffer+0x4/0x30 serdev_device_write_flush+0x24/0x34 qca_serdev_shutdown+0x80/0x130 [hci_uart] device_shutdown+0x15c/0x260 kernel_restart+0x48/0xac KASAN report: BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50 Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1 CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted 6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: dump_backtrace.part.0+0xdc/0xf0 show_stack+0x18/0x30 dump_stack_lvl+0x68/0x84 print_report+0x188/0x488 kasan_report+0xa4/0xf0 __asan_load8+0x80/0xac tty_driver_flush_buffer+0x1c/0x50 ttyport_write_flush+0x34/0x44 serdev_device_write_flush+0x48/0x60 qca_serdev_shutdown+0x124/0x274 device_shutdown+0x1e8/0x350 kernel_restart+0x48/0xb0 __do_sys_reboot+0x244/0x2d0 __arm64_sys_reboot+0x54/0x70 invoke_syscall+0x60/0x190 el0_svc_common.constprop.0+0x7c/0x160 do_el0_svc+0x44/0xf0 el0_svc+0x2c/0x6c el0t_64_sync_handler+0xbc/0x140 el0t_64_sync+0x190/0x194 Fixes: 7e7bbddd029b ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-25treewide: Convert del_timer*() to timer_shutdown*()Steven Rostedt (Google)1-1/+1
Due to several bugs caused by timers being re-armed after they are shutdown and just before they are freed, a new state of timers was added called "shutdown". After a timer is set to this state, then it can no longer be re-armed. The following script was run to find all the trivial locations where del_timer() or del_timer_sync() is called in the same function that the object holding the timer is freed. It also ignores any locations where the timer->function is modified between the del_timer*() and the free(), as that is not considered a "trivial" case. This was created by using a coccinelle script and the following commands: $ cat timer.cocci @@ expression ptr, slab; identifier timer, rfield; @@ ( - del_timer(&ptr->timer); + timer_shutdown(&ptr->timer); | - del_timer_sync(&ptr->timer); + timer_shutdown_sync(&ptr->timer); ) ... when strict when != ptr->timer ( kfree_rcu(ptr, rfield); | kmem_cache_free(slab, ptr); | kfree(ptr); ) $ spatch timer.cocci . > /tmp/t.patch $ patch -p1 < /tmp/t.patch Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/ Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ] Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ] Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-12-13Merge tag 'net-next-6.2' of ↵Linus Torvalds13-53/+2829
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Paolo Abeni: "Core: - Allow live renaming when an interface is up - Add retpoline wrappers for tc, improving considerably the performances of complex queue discipline configurations - Add inet drop monitor support - A few GRO performance improvements - Add infrastructure for atomic dev stats, addressing long standing data races - De-duplicate common code between OVS and conntrack offloading infrastructure - A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements - Netfilter: introduce packet parser for tunneled packets - Replace IPVS timer-based estimators with kthreads to scale up the workload with the number of available CPUs - Add the helper support for connection-tracking OVS offload BPF: - Support for user defined BPF objects: the use case is to allocate own objects, build own object hierarchies and use the building blocks to build own data structures flexibly, for example, linked lists in BPF - Make cgroup local storage available to non-cgroup attached BPF programs - Avoid unnecessary deadlock detection and failures wrt BPF task storage helpers - A relevant bunch of BPF verifier fixes and improvements - Veristat tool improvements to support custom filtering, sorting, and replay of results - Add LLVM disassembler as default library for dumping JITed code - Lots of new BPF documentation for various BPF maps - Add bpf_rcu_read_{,un}lock() support for sleepable programs - Add RCU grace period chaining to BPF to wait for the completion of access from both sleepable and non-sleepable BPF programs - Add support storing struct task_struct objects as kptrs in maps - Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer values - Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions Protocols: - TCP: implement Protective Load Balancing across switch links - TCP: allow dynamically disabling TCP-MD5 static key, reverting back to fast[er]-path - UDP: Introduce optional per-netns hash lookup table - IPv6: simplify and cleanup sockets disposal - Netlink: support different type policies for each generic netlink operation - MPTCP: add MSG_FASTOPEN and FastOpen listener side support - MPTCP: add netlink notification support for listener sockets events - SCTP: add VRF support, allowing sctp sockets binding to VRF devices - Add bridging MAC Authentication Bypass (MAB) support - Extensions for Ethernet VPN bridging implementation to better support multicast scenarios - More work for Wi-Fi 7 support, comprising conversion of all the existing drivers to internal TX queue usage - IPSec: introduce a new offload type (packet offload) allowing complete header processing and crypto offloading - IPSec: extended ack support for more descriptive XFRM error reporting - RXRPC: increase SACK table size and move processing into a per-local endpoint kernel thread, reducing considerably the required locking - IEEE 802154: synchronous send frame and extended filtering support, initial support for scanning available 15.4 networks - Tun: bump the link speed from 10Mbps to 10Gbps - Tun/VirtioNet: implement UDP segmentation offload support Driver API: - PHY/SFP: improve power level switching between standard level 1 and the higher power levels - New API for netdev <-> devlink_port linkage - PTP: convert existing drivers to new frequency adjustment implementation - DSA: add support for rx offloading - Autoload DSA tagging driver when dynamically changing protocol - Add new PCP and APPTRUST attributes to Data Center Bridging - Add configuration support for 800Gbps link speed - Add devlink port function attribute to enable/disable RoCE and migratable - Extend devlink-rate to support strict prioriry and weighted fair queuing - Add devlink support to directly reading from region memory - New device tree helper to fetch MAC address from nvmem - New big TCP helper to simplify temporary header stripping New hardware / drivers: - Ethernet: - Marvel Octeon CNF95N and CN10KB Ethernet Switches - Marvel Prestera AC5X Ethernet Switch - WangXun 10 Gigabit NIC - Motorcomm yt8521 Gigabit Ethernet - Microchip ksz9563 Gigabit Ethernet Switch - Microsoft Azure Network Adapter - Linux Automation 10Base-T1L adapter - PHY: - Aquantia AQR112 and AQR412 - Motorcomm YT8531S - PTP: - Orolia ART-CARD - WiFi: - MediaTek Wi-Fi 7 (802.11be) devices - RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB devices - Bluetooth: - Broadcom BCM4377/4378/4387 Bluetooth chipsets - Realtek RTL8852BE and RTL8723DS - Cypress.CYW4373A0 WiFi + Bluetooth combo device Drivers: - CAN: - gs_usb: bus error reporting support - kvaser_usb: listen only and bus error reporting support - Ethernet NICs: - Intel (100G): - extend action skbedit to RX queue mapping - implement devlink-rate support - support direct read from memory - nVidia/Mellanox (mlx5): - SW steering improvements, increasing rules update rate - Support for enhanced events compression - extend H/W offload packet manipulation capabilities - implement IPSec packet offload mode - nVidia/Mellanox (mlx4): - better big TCP support - Netronome Ethernet NICs (nfp): - IPsec offload support - add support for multicast filter - Broadcom: - RSS and PTP support improvements - AMD/SolarFlare: - netlink extened ack improvements - add basic flower matches to offload, and related stats - Virtual NICs: - ibmvnic: introduce affinity hint support - small / embedded: - FreeScale fec: add initial XDP support - Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood - TI am65-cpsw: add suspend/resume support - Mediatek MT7986: add RX wireless wthernet dispatch support - Realtek 8169: enable GRO software interrupt coalescing per default - Ethernet high-speed switches: - Microchip (sparx5): - add support for Sparx5 TC/flower H/W offload via VCAP - Mellanox mlxsw: - add 802.1X and MAC Authentication Bypass offload support - add ip6gre support - Embedded Ethernet switches: - Mediatek (mtk_eth_soc): - improve PCS implementation, add DSA untag support - enable flow offload support - Renesas: - add rswitch R-Car Gen4 gPTP support - Microchip (lan966x): - add full XDP support - add TC H/W offload via VCAP - enable PTP on bridge interfaces - Microchip (ksz8): - add MTU support for KSZ8 series - Qualcomm 802.11ax WiFi (ath11k): - support configuring channel dwell time during scan - MediaTek WiFi (mt76): - enable Wireless Ethernet Dispatch (WED) offload support - add ack signal support - enable coredump support - remain_on_channel support - Intel WiFi (iwlwifi): - enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities - 320 MHz channels support - RealTek WiFi (rtw89): - new dynamic header firmware format support - wake-over-WLAN support" * tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits) ipvs: fix type warning in do_div() on 32 bit net: lan966x: Remove a useless test in lan966x_ptp_add_trap() net: ipa: add IPA v4.7 support dt-bindings: net: qcom,ipa: Add SM6350 compatible bnxt: Use generic HBH removal helper in tx path IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver selftests: forwarding: Add bridge MDB test selftests: forwarding: Rename bridge_mdb test bridge: mcast: Support replacement of MDB port group entries bridge: mcast: Allow user space to specify MDB entry routing protocol bridge: mcast: Allow user space to add (*, G) with a source list and filter mode bridge: mcast: Add support for (*, G) with a source list and filter mode bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source bridge: mcast: Add a flag for user installed source entries bridge: mcast: Expose __br_multicast_del_group_src() bridge: mcast: Expose br_multicast_new_group_src() bridge: mcast: Add a centralized error path bridge: mcast: Place netlink policy before validation functions bridge: mcast: Split (*, G) and (S, G) addition into different functions bridge: mcast: Do not derive entry type from its filter mode ...
2022-12-12Bluetooth: hci_bcsp: don't call kfree_skb() under spin_lock_irqsave()Yang Yingliang1-1/+1
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_h5: don't call kfree_skb() under spin_lock_irqsave()Yang Yingliang1-1/+1
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 43eb12d78960 ("Bluetooth: Fix/implement Three-wire reliable packet sending") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_ll: don't call kfree_skb() under spin_lock_irqsave()Yang Yingliang1-1/+1
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 166d2f6a4332 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_qca: don't call kfree_skb() under spin_lock_irqsave()Yang Yingliang1-1/+1
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 0ff252c1976d ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: don't call kfree_skb() under spin_lock_irqsave()Yang Yingliang1-3/+3
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 803b58367ffb ("Bluetooth: btusb: Implement driver internal packet reassembly") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btintel: Fix missing free skb in btintel_setup_combined()Wang ShaoBo1-2/+3
skb allocated by __hci_cmd_sync would not be used whether in checking for supported iBT hardware variants or after, we should free it in all error branches, this patch makes the case read version failed or default error case free skb before return. Fixes: c86c7285bb08 ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version") Fixes: 019a1caa7fd2 ("Bluetooth: btintel: Refactoring setup routine for bootloader devices") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btintel: Fix existing sparce warningsLuiz Augusto von Dentz1-8/+8
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btintel.c:1041:38: warning: cast to restricted __le32 drivers/bluetooth/btintel.c:1786:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1795:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1796:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1797:25: warning: cast to restricted __le16 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Fix existing sparce warningLuiz Augusto von Dentz1-1/+1
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btusb.c:3426:28: warning: cast to restricted __le32 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Fix new sparce warningsLuiz Augusto von Dentz1-12/+13
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Add a new PID/VID 13d3/3549 for RTL8822CUGongwei Li1-0/+4
* /sys/kernel/debug/usb/devices T: Bus=03 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b85b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Gongwei Li <ligongwei@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0cb8:0xc559Artem Lukyanov1-0/+4
Add the support ID(0x0cb8, 0xc559) to usb_device_id table for Realtek RTL8852BE. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c559 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Artem Lukyanov <dukzcry@ya.ru> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Add a new VID/PID 0489/e0f2 for MT7922Andy Chi1-0/+3
Add VID/PID 0489/e0f2 for MediaTek MT7922 Bluetooth chip. Found and tested with HP ProBook. From /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f2 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Andy Chi <andy.chi@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_bcm4377: Fix missing pci_disable_device() on error in ↵Yang Yingliang1-1/+1
bcm4377_probe() pci_disable_device() need be called while module exiting, switch to use pcim_enable(), pci_disable_device() will be called in pcim_release() after probe() failure. Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Add Realtek 8761BUV support ID 0x2B89:0x8761Raman Varabets1-0/+2
Identifies as "Realtek Bluetooth Radio"; used in UGREEN CM390 (P/N 80889). Device description at /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2b89 ProdID=8761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Raman Varabets <linux-bluetooth@cyborgize.sg> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boardsSven Peter3-0/+2527
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple machines. This driver adds support for the Bluetooth function which exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic. Signed-off-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_bcm: Add CYW4373A0 supportMarek Vasut1-1/+12
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress. This chip is present e.g. on muRata 2AE module. This chip has additional quirk where the HCI command 0xfc45, used on older chips to switch UART clock from 24 MHz to 48 MHz, to support baudrates over 3 Mbdps, is no longer recognized by this newer chip. This newer chip can configure the 4 Mbdps baudrate without the need to issue HCI command 0xfc45, so add flag to indicate this and do not issue the command on this chip to avoid failure to set 4 Mbdps baud rate. It is not clear whether there is a way to determine which chip does and which chip does not support the HCI command 0xfc45, other than trial and error. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Add more device IDs for WCN6855Shengyu Qu1-0/+84
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10) Windows driver download address: https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/ thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads /driver-list/ Signed-off-by: Shengyu Qu <wiagn233@outlook.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Default CONFIG_BT_HCIBTUSB_POLL_SYNC=yLuiz Augusto von Dentz1-0/+1
poll_sync has been proven to fix races of USB data and event endpoints so this enables it by default. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
2022-12-12Bluetooth: btusb: Add CONFIG_BT_HCIBTUSB_POLL_SYNCLuiz Augusto von Dentz2-0/+13
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the default behavior of Bluetooth USB controller with respect to poll synchronization of its endpoits. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
2022-12-12virtio_bt: Fix alignment in configuration structIgor Skalkin1-3/+13
The current version of the configuration structure has unaligned 16-bit fields, but according to the specification [1], access to the configuration space must be aligned. Add a second, aligned version of the configuration structure and a new feature bit indicating that this version is being used. [1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: hci_qca: only assign wakeup with serial port supportZhengping Jiang1-1/+2
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise it will fall back to the hci_uart_wakeup or the behavior that can be overridden before calling the hci_uart_register_device(). Signed-off-by: Zhengping Jiang <jiangzp@google.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Ignore zero length of USB packets on ALT 6 for specific chipHilda Wu2-2/+30
For USB ALT 6 settings some Realtek chips need to transmit mSBC data continuously without the zero length of USB packets. In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior. Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific chip model for the behavior. Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btrtl: Add btrealtek data structHilda Wu2-0/+24
This patch adds a data structure for btrealtek object, and the definition of vendor behavior flags. It also adds macros to set/test/get the flags. Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: virtio_bt: fix device removalMichael S. Tsirkin1-2/+17
Device removal is clearly out of virtio spec: it attempts to remove unused buffers from a VQ before invoking device reset. To fix, make open/close NOPs and do all cleanup/setup in probe/remove. NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is not really what a driver is supposed to be doing. These are transport enable/disable callbacks from the BT core towards the driver. It maps to a device being enabled/disabled by something like bluetoothd for example. So if disabled, users expect that no resources/queues are in use. It does work with all other transports like USB, SDIO, UART etc. There should be no buffer used if the device is powered off. We also don’t have any USB URBs in-flight if the transport is not active. The way to implement a proper fix would be using vq reset if supported, or even using a full device reset. The cost of the hack is a single skb wasted on an unused bt device. NB2: with this fix in place driver still suffers from a race condition if an interrupt triggers while device is being reset. To fix, in the virtbt_close() callback we should deactivate all interrupts. To be fixed. squashed fixup: bluetooth: virtio_bt: fix an error code in probe() Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Message-Id: <20220811080943.198245-1-mst@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
2022-12-12Bluetooth: Work around SCO over USB HCI design defectNicolas Cavallari1-2/+33
The USB interface between the host and the bluetooth adapter used for SCO packets uses an USB isochronous endpoint with a fragmentation scheme that does not tolerate errors. Except USB isochronous transfers do not provide a reliable stream with guaranteed delivery. (There is no retry on error, see USB spec v2.0 5.6 and 8.5.5.) To fragment a packet, the bluetooth HCI simply splits it in parts and transfer them as-is. The receiver is expected to reconstruct the packet by assuming the first fragment contains the header and parsing its size field. There is no error detection either. If a fragment is lost, the end result is that the kernel is no longer synchronized and will pass malformed data to the upper layers, since it has no way to tell if the first fragment is an actual first fragment or a continuation fragment. Resynchronization can only happen by luck and requires an unbounded amount of time. The typical symptom for a HSP/HFP bluetooth headset is that the microphone stops working and dmesg contains piles of rate-limited "Bluetooth: hci0: SCO packet for unknown connection handle XXXX" errors for an indeterminate amount of time, until the kernel accidentally resynchronize. A workaround is to ask the upper layer to prevalidate the first fragment header. This is not possible with user channels so this workaround is disabled in this case. This problem is the most severe when using an ath3k adapter on an i.MX 6 board, where packet loss occur regularly, possibly because it is an USB1 device connected on an USB2 hub and this is a special case requiring split transactions. Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Bluetooth: btusb: Introduce generic USB resetArchie Pusaka1-10/+25
On cmd_timeout with no reset_gpio, reset the USB port as a last resort. This patch changes the behavior of btusb_intel_cmd_timeout and btusb_rtl_cmd_timeout. Signed-off-by: Archie Pusaka <apusaka@chromium.org> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com> Reviewed-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12btusb: Avoid reset of ISOC endpoint alt settings to zeroChethan Tumkur Narayan1-2/+3
In case of suspend/resume and HCI_RESET (BT On and Off), ISOC endpoint set to alt setting 0 when no SCO connection exists. This patch shall avoid resetting of ISOC endpoint to alt setting to 0. Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-12Merge tag 'timers-core-2022-12-10' of ↵Linus Torvalds1-2/+8
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer updates from Thomas Gleixner: "Updates for timers, timekeeping and drivers: Core: - The timer_shutdown[_sync]() infrastructure: Tearing down timers can be tedious when there are circular dependencies to other things which need to be torn down. A prime example is timer and workqueue where the timer schedules work and the work arms the timer. What needs to prevented is that pending work which is drained via destroy_workqueue() does not rearm the previously shutdown timer. Nothing in that shutdown sequence relies on the timer being functional. The conclusion was that the semantics of timer_shutdown_sync() should be: - timer is not enqueued - timer callback is not running - timer cannot be rearmed Preventing the rearming of shutdown timers is done by discarding rearm attempts silently. A warning for the case that a rearm attempt of a shutdown timer is detected would not be really helpful because it's entirely unclear how it should be acted upon. The only way to address such a case is to add 'if (in_shutdown)' conditionals all over the place. This is error prone and in most cases of teardown not required all. - The real fix for the bluetooth HCI teardown based on timer_shutdown_sync(). A larger scale conversion to timer_shutdown_sync() is work in progress. - Consolidation of VDSO time namespace helper functions - Small fixes for timer and timerqueue Drivers: - Prevent integer overflow on the XGene-1 TVAL register which causes an never ending interrupt storm. - The usual set of new device tree bindings - Small fixes and improvements all over the place" * tag 'timers-core-2022-12-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits) dt-bindings: timer: renesas,cmt: Add r8a779g0 CMT support dt-bindings: timer: renesas,tmu: Add r8a779g0 support clocksource/drivers/arm_arch_timer: Use kstrtobool() instead of strtobool() clocksource/drivers/timer-ti-dm: Fix missing clk_disable_unprepare in dmtimer_systimer_init_clock() clocksource/drivers/timer-ti-dm: Clear settings on probe and free clocksource/drivers/timer-ti-dm: Make timer_get_irq static clocksource/drivers/timer-ti-dm: Fix warning for omap_timer_match clocksource/drivers/arm_arch_timer: Fix XGene-1 TVAL register math error clocksource/drivers/timer-npcm7xx: Enable timer 1 clock before use dt-bindings: timer: nuvoton,npcm7xx-timer: Allow specifying all clocks dt-bindings: timer: rockchip: Add rockchip,rk3128-timer clockevents: Repair kernel-doc for clockevent_delta2ns() clocksource/drivers/ingenic-ost: Define pm functions properly in platform_driver struct clocksource/drivers/sh_cmt: Access registers according to spec vdso/timens: Refactor copy-pasted find_timens_vvar_page() helper into one copy Bluetooth: hci_qca: Fix the teardown problem for real timers: Update the documentation to reflect on the new timer_shutdown() API timers: Provide timer_shutdown[_sync]() timers: Add shutdown mechanism to the internal functions timers: Split [try_to_]del_timer[_sync]() to prepare for shutdown mode ...
2022-12-02Bluetooth: btusb: Add debug message for CSR controllersIsmael Ferreras Morezuelas1-0/+5
The rationale of showing this is that it's potentially critical information to diagnose and find more CSR compatibility bugs in the future and it will save a lot of headaches. Given that clones come from a wide array of vendors (some are actually Barrot, some are something else) and these numbers are what let us find differences between actual and fake ones, it will be immensely helpful to scour the Internet looking for this pattern and building an actual database to find correlations and improve the checks. Cc: stable@vger.kernel.org Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-12-02Bluetooth: btusb: Fix CSR clones again by re-adding ERR_DATA_REPORTING quirkIsmael Ferreras Morezuelas1-0/+1
A patch series by a Qualcomm engineer essentially removed my quirk/workaround because they thought it was unnecessary. It wasn't, and it broke everything again: https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=* He argues that the quirk is not necessary because the code should check if the dongle says if it's supported or not. The problem is that for these Chinese CSR clones they say that it would work: = New Index: 00:00:00:00:00:00 (Primary,USB,hci0) = Open Index: 00:00:00:00:00:00 < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 > [hci0] 11.276039 Read Local Version Information (0x04|0x0001) ncmd 1 Status: Success (0x00) HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810) LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312) Manufacturer: Cambridge Silicon Radio (10) ... < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 68 > [hci0] 11.668030 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 163 entries ... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ... ... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 = Close Index: 00:1A:7D:DA:71:XX So bring it back wholesale. Fixes: 63b1a7dd38bf ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING") Fixes: e168f6900877 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR") Fixes: 766ae2422b43 ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk") Cc: stable@vger.kernel.org Cc: Zijun Hu <quic_zijuhu@quicinc.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-11-24Bluetooth: hci_qca: Fix the teardown problem for realThomas Gleixner1-2/+8
While discussing solutions for the teardown problem which results from circular dependencies between timers and workqueues, where timers schedule work from their timer callback and workqueues arm the timers from work items, it was discovered that the recent fix to the QCA code is incorrect. That commit fixes the obvious problem of using del_timer() instead of del_timer_sync() and reorders the teardown calls to destroy_workqueue(wq); del_timer_sync(t); This makes it less likely to explode, but it's still broken: destroy_workqueue(wq); /* After this point @wq cannot be touched anymore */ ---> timer expires queue_work(wq) <---- Results in a NULL pointer dereference deep in the work queue core code. del_timer_sync(t); Use the new timer_shutdown_sync() function to ensure that the timers are disarmed, no timer callbacks are running and the timers cannot be armed again. This restores the original teardown sequence: timer_shutdown_sync(t); destroy_workqueue(wq); which is now correct because the timer core silently ignores potential rearming attempts which can happen when destroy_workqueue() drains pending work before mopping up the workqueue. Fixes: 72ef98445aca ("Bluetooth: hci_qca: Use del_timer_sync() before freeing") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Acked-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Link: https://lore.kernel.org/all/87iljhsftt.ffs@tglx Link: https://lore.kernel.org/r/20221123201625.435907114@linutronix.de
2022-11-02Bluetooth: virtio_bt: Use skb_put to set lengthSoenke Huster1-1/+1
By using skb_put we ensure that skb->tail is set correctly. Currently, skb->tail is always zero, which leads to errors, such as the following page fault in rfcomm_recv_frame: BUG: unable to handle page fault for address: ffffed1021de29ff #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751) Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver") Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-19Bluetooth: hci_{ldisc,serdev}: check percpu_init_rwsem() failureTetsuo Handa2-5/+12
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1], for rcu_sync_enter() is called without rcu_sync_init() due to hci_uart_tty_open() ignoring percpu_init_rwsem() failure. While we are at it, fix that hci_uart_register_device() ignores percpu_init_rwsem() failure and hci_uart_unregister_device() does not call percpu_free_rwsem(). Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1] Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: 67d2f8781b9f00d1 ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.") Fixes: d73e172816652772 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-14Bluetooth: btusb: Add a new VID/PID 0e8d/0608 for MT7921Daniel Golle1-0/+3
Add a new PID/VID 0e8d/0608 for MT7921K chip found on AMD RZ608 module. From /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=0608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-14Bluetooth: btusb: Add a new PID/VID 13d3/3583 for MT7921Sean Wang1-0/+3
Add VID 13D3 & PID 3583 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3583 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btintel: Mark Intel controller to support LE_STATES quirkKiran K1-9/+8
HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers are marked to support HCI_QUIRK_LE_STATES. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btintel: Add support for MagnetorKiran K1-0/+3
Hardware variant for Magnetor core (CNVi) is added. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-09Bluetooth: btusb: Add a new PID/VID 13d3/3578 for MT7921Chris Lu1-0/+3
Add VID 13D3 & PID 3578 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=01 Prnt=01 Port=07 Cnt=03 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3578 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-09-01Bluetooth: btusb: mediatek: fix WMT failure during runtime suspendSean Wang1-0/+14
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it needs constantly polling control pipe until the host received the WMT event, thus, we should require to specifically acquire PM counter on the USB to prevent the interface from entering auto suspended while WMT cmd/event in progress. Fixes: a1c49c434e15 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Co-developed-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-31Bluetooth: btusb: Add BT device 0cb8:c549 from RTW8852AE to tablesLarry Finger1-0/+2
A new Bluetooth device for the Realtek RTW8852AE has been noted. This device has the following lsusb output: Bus 001 Device 003: ID 0cb8:c549 Opticis Co., Ltd Bluetooth Radio The pertinent part of /sys/kernel/debug/usb/devices is as follows: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c549 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-31Bluetooth: btusb: Add RTL8761BUV device (Edimax BT-8500)Szabolcs Sipos1-0/+2
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=7392 ProdID=c611 Rev= 2.00 S: Manufacturer=Realtek S: Product=Edimax Bluetooth Adapter S: SerialNumber=XXXXXXXXXXXX C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Szabolcs Sipos <labuwx@balfug.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-31Bluetooth: btusb: RTL8761BUV consistent namingSzabolcs Sipos1-5/+1
Based on photos available from the FCC, all currently supported RTL8761B series USB dongles have the same chip: RTL8761BUV. rtl8761bu is often used to refer to this chip. rtl8761b sometimes refers to this chip, and other times to its UART variant (RTL8761BTV). +----------------+---------+---------+---------------+ | Dongle | USB VID | USB PID | FCC ID | +----------------+---------+---------+---------------+ | ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 | | TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 | | EDUP EP-B3519 | | | 2AHRD-EPB3519 | | EDUP EP-B3536 | | | 2AHRDEP-B3536 | | UGREEN CM390 | | | 2AQI5-CM390 | +----------------+---------+---------+---------------+ Signed-off-by: Szabolcs Sipos <labuwx@balfug.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-31Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3592Max Chou1-0/+2
Add the support ID(0x13D3, 0x3592) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3592 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-25Bluetooth: Add VID/PID 0489/e0e0 for MediaTek MT7921Fae1-0/+3
Tested on HP Envy ey0xxx output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e0 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Fae <faenkhauser@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-08-04Merge tag 'spdx-6.0-rc1' of ↵Linus Torvalds5-72/+5
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx Pull SPDX updates from Greg KH: "Here is the set of SPDX comment updates for 6.0-rc1. Nothing huge here, just a number of updated SPDX license tags and cleanups based on the review of a number of common patterns in GPLv2 boilerplate text. Also included in here are a few other minor updates, two USB files, and one Documentation file update to get the SPDX lines correct. All of these have been in the linux-next tree for a very long time" * tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits) Documentation: samsung-s3c24xx: Add blank line after SPDX directive x86/crypto: Remove stray comment terminator treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2) treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1) treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE ...
2022-07-22Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packetLuiz Augusto von Dentz1-0/+10
Fix up the packet type if ISO packets are sent over the bulk endpoint. Note: This is a stopgap since the Bluetooth specification currently doesn't define any endpoint to transport ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2022-07-22Bluetooth: btusb: Add support for ISO packetsLuiz Augusto von Dentz1-0/+14
This enabled btusb driver to properly transmit ISO packets. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-06-27 01:05:13 +0000