| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
serdev_device_write()
serdev_device_write() is not appropriate at here because
serdev_device_write_wakeup() is not used to release completion hold
by the former at @write_wakeup member of struct serdev_device_ops.
Fix by using serdev_device_write_buf() instead of serdev_device_write().
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Calls of the functions clk_disable_unprepare() and hci_free_dev()
were missing for the exception handling.
Thus add the missed function calls together with corresponding
jump targets.
Fixes: 055825614c6b ("Bluetooth: btmtkuart: add an implementation for clock osc property")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some board requires explicitily control external osscilator via GPIO.
So, add an implementation of a clock property for an external oscillator
to the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so the driver
adds additional boot-gpios to let the MT766[3,8]U can enter the proper boot
mode by gpiod for such platform.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed warning: incorrect type in assignment reported by kbuild test robot.
The detailed warning is shown as below.
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
All warnings (new ones prefixed by >>):
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
sparse warnings: (new ones prefixed by >>)
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
vim +671 drivers/bluetooth/btmtkuart.c
659
660 static int btmtkuart_change_baudrate(struct hci_dev *hdev)
661 {
662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
663 struct btmtk_hci_wmt_params wmt_params;
664 u32 baudrate;
665 u8 param;
666 int err;
667
668 /* Indicate the device to enter the probe state the host is
669 * ready to change a new baudrate.
670 */
> 671 baudrate = cpu_to_le32(bdev->desired_speed);
672 wmt_params.op = MTK_WMT_HIF;
Fixes: 22eaf6c9946a ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds the support of enabling MT7663U and MT7668U Bluetooth function
running on the top of btmtkuart driver.
There are a few differences between MT766[3,8]U and MT7622 where
MT766[3,8]U are standalone devices based on UART transport while MT7622
bluetooth is a built-in device on MediaTek SoC communicating with the host
through BTIF serial transport. Thus, extra setup sequence is necessary
for these standalone devices such as remote regulator and reset control via
GPIO, baud rate changing handshake between the host and device and so on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Update the setup sequence on MT7622 to apply the same flow with MT7663U
and MT7668U USB [1] as much as possible. These additional commands are
required to parse the corresponding event to determine what current state
the Bluetooth device is on and thus it's necessary to extend
mtk_hci_wmt_sync to support the reading status in the same patch.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pass a structure pointer to mtk_hci_wmt_sync rather than several arguments
to avoid take up additional stack area and be better to read the code.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Restore bdev->tx_state with clearing bit BTMTKUART_TX_WAIT_VND_EVT
when there is an error on waiting for the corresponding event.
Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
add a trivial typo fix from speicfic to specific
Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case memory resources for *fw* were allocated, release them before
return.
Addresses-Coverity-ID: 1472611 ("Resource leak")
Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We're supposed to pass the number of elements in the mtk_recv_pkts, not
the number of bytes.
Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds a driver based on serdev driver for the MediaTek serial protocol
based on running H:4, which can enable the built-in Bluetooth device inside
MT7622 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
