summaryrefslogtreecommitdiffstats
path: root/drivers/bluetooth/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2013-01-18tty: Added a CONFIG_TTY option to allow removal of TTYJoe Millenbach1-0/+1
The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-07-17Bluetooth: Initial skeleton for Three-wire UART (H5) supportJohan Hedberg1-0/+12
This patch adds the initial skeleton for Three-wire UART (H5) support and hooks it up to the HCI UART framework. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2011-11-21Bluetooth: btmrvl: support Marvell Bluetooth device SD8797Bing Zhao1-3/+3
The SD8797 firmware image is shared with mwifiex driver. Whoever gets loaded first will be responsible for firmware downloading. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-04-13Bluetooth: btmrvl: support Marvell Bluetooth device SD8787Kevin Gan1-2/+2
The SD8787 firmware image is shared with mwifiex driver. Whoever gets loaded first will be responsible for firmware downloading. Signed-off-by: Kevin Gan <ganhy@marvell.com> Signed-off-by: Tristan Xu <xurf@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-23Bluetooth: btwilink driverPavan Savoy1-0/+10
This is the bluetooth protocol driver for the TI WiLink7 chipsets. Texas Instrument's WiLink chipsets combine wireless technologies like BT, FM, GPS and WLAN onto a single chip. This Bluetooth driver works on top of the TI_ST shared transport line discipline driver which also allows other drivers like FM V4L2 and GPS character driver to make use of the same UART interface. Kconfig and Makefile modifications to enable the Bluetooth driver for Texas Instrument's WiLink 7 chipset. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-07-21Bluetooth: Support for Atheros AR300x serial chipSuraj Sumangala1-0/+12
Implements Atheros AR300x serial HCI protocol. This protocol extends H4 serial protocol to implement enhanced power management features supported by Atheros AR300x serial Bluetooth chipsets. Signed-off-by: Suraj Sumangala <suraj@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-01-30Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011Vikram Kandukuri1-1/+12
Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com> Signed-off-by: Alicke Xu <sxu@atheros.com> Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Fix Kconfig for Marvell Bluetooth driverMarcel Holtmann1-2/+1
The Marvell driver selects DEBUG_FS and FW_LOADER for its core driver and that is pointless. Don't select DEBUG_FS since it is either enabled or not and it is not for the driver to enable it. Also FW_LOADER is only used within the SDIO driver and so just have that one select the FW_LOADER option. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add debugfs support to btmrvl driverBing Zhao1-0/+1
/debug/btmrvl/config/ /debug/btmrvl/status/ See Documentation/btmrvl.txt for details. This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add Marvell BT-over-SDIO driverBing Zhao1-0/+13
This driver supports Marvell Bluetooth enabled devices with SDIO interface. Currently only SD8688 chip is supported. The helper/firmware images of SD8688 can be downloaded from this tree: git://git.infradead.org/users/dwmw2/linux-firmware.git This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add btmrvl driver for Marvell Bluetooth devicesBing Zhao1-0/+12
This driver provides basic definitions and library functions to support Marvell Bluetooth enabled devices, such as 88W8688 WLAN/BT combo chip. This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Remove deprecated hci_usb driverMarcel Holtmann1-20/+0
The old hci_usb driver has been fully replaced with the new btusb driver and all major distributions switched to the new driver now. This removes it since it should not be used at all anymore. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18[Bluetooth] Add SCO support to btusb driverMarcel Holtmann1-6/+4
The new generic driver for Bluetooth USB devices was missing proper SCO support. The driver now claims the second interface for these USB devices to allow the flow of SCO packets. It also handles switching of the alternate setting and re-submission of isochronous URBs. The btusb driver is now a full replacement for hci_usb and thus the experimental tag has been removed and this driver is promoted as preferred one. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-15bluetooth/hci_bcsp: fix bitrev KconfigRandy Dunlap1-1/+1
Fix bluetooth hci_bcsp Kconfig to avoid build errors: drivers/built-in.o: In function `bcsp_prepare_pkt': hci_bcsp.c:(.text+0x7e9ac): undefined reference to `bitrev16' drivers/built-in.o: In function `bcsp_recv': hci_bcsp.c:(.text+0x7f276): undefined reference to `bitrev16' hci_bcsp.c:(.text+0x7f293): undefined reference to `bitrev16' make[1]: *** [.tmp_vmlinux1] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Ackey-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-10bluetooth: hci_bcsp.c small cleanups/api usersHarvey Harrison1-0/+1
Use bitrev16 from lib/bitrev.c. Use the get_unaligned_be16 to get the crc from the packet, create a small helper function for this. Fix a shadowed variable sparse warning: drivers/bluetooth/hci_bcsp.c:218:26: warning: symbol 'hdr' shadows an earlier one drivers/bluetooth/hci_bcsp.c:187:5: originally declared here [akpm@linux-foundation.org: select CONFIG_BITREVERSE, noted by akinobu.mita@gmail.com] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-22[Bluetooth] Add generic driver for Bluetooth USB devicesMarcel Holtmann1-0/+13
This patch adds a new generic driver for Bluetooth USB devices. This driver is still experimental at this point, but it is cleaner and easier to maintain than the current Bluetooth USB driver. It is a much better starting point for power management improvements. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-22[Bluetooth] Add generic driver for Bluetooth SDIO devicesMarcel Holtmann1-0/+11
This patch adds a generic driver for Bluetooth SDIO devices. It supports Type-A and Type-B devices. Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-22[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chipsOhad Ben-Cohen1-0/+11
Add support for Texas Instruments' HCI Low Level (HCILL) Bluetooth protocol, which is a power management extension to H4. The HCILL is widely used by TI's BRF63xx Bluetooth chips. Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-10-28[Bluetooth] Remove TXCRC compile option for BCSP driverMarcel Holtmann1-8/+0
The TXCRC compile option is not really useful and thus change it into a module parameter. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2005-04-16Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds1-0/+168
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!