| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If store_mem_state() is called to online memory which is already online,
it will return 1, the value it got from device_online().
This is wrong because store_mem_state() is a device_attribute .store
function. Thus a non-negative return value represents input bytes read.
Set the return value to -EINVAL in this case.
Link: http://lkml.kernel.org/r/1472743777-24266-1-git-send-email-arbab@linux.vnet.ibm.com
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Seth Jennings <sjenning@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.9 cycle.
General improvements:
- nicer debugfs output with one pin/config pair per line.
- continued efforts to strictify module vs bool.
- constification and similar from Coccinelle engineers.
- return error from pinctrl_bind_pins()
- pulling in the ability to selectively disable mapping of unusable
IRQs from the GPIO subsystem.
New drivers:
- new driver for the Aspeed pin controller family: AST2400 (G4) and
AST2500 (G5) are supported. These are used by OpenBMC on the IBM
Witherspoon platform.
- new subdriver for the Allwinner sunxi GR8.
Driver improvements:
- drop default IRQ trigger types assigned during IRQ mapping on AT91
and Nomadik. This error was identified by improvements in the IRQ
core by Marc Zyngier.
- active high/low types on the GPIO IRQs for the ST pin controller.
- IRQ support on GPIOs on the STM32 pin controller.
- Renesas Super-H/ARM sh-pfc: continued massive developments.
- misc MXC improvements.
- SPDIF on the Allwiner A31 SoC
- IR remote and SPI NOR flash, NAND flash, I2C pins on the AMLogic
SoC.
- PWM pins on the Meson.
- do not map unusable IRQs (taken by BIOS) on the Intel Cherryview.
- add GPIO IRQ wakeup support to the Intel driver so we can wake up
from button pushes.
Deprecation:
- delete the obsolete STiH415/6 SoC support"
* tag 'pinctrl-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: qcom: fix masking of pinmux functions
pinctrl: intel: Configure GPIO chip IRQ as wakeup interrupts
pinctrl: cherryview: Convert to use devm_gpiochip_add_data()
pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain
gpiolib: Make it possible to exclude GPIOs from IRQ domain
pinctrl: nomadik: don't default-flag IRQs as falling
pinctrl: st: Remove obsolete platforms from pinctrl-st dt doc
pinctrl: st: Remove STiH415/6 SoC pinctrl driver support.
pinctrl: amlogic: gxbb: add i2c pins
pinctrl: amlogic: gxbb: add nand pins
pinctrl: stm32: add IRQ_DOMAIN_HIERARCHY dependency
pinctrl: amlogic: gxbb: add spi nor pins
pinctrl: sh-pfc: r8a7794: Implement voltage switching for SDHI
pinctrl: sh-pfc: r8a7791: Implement voltage switching for SDHI
pinctrl: sh-pfc: Add PORT_GP_24 helper macro
pinctrl: Fix "st,syscfg" definition for STM32 pinctrl
driver: base: pinctrl: return error from pinctrl_bind_pins()
pinctrl: meson-gxbb: add the missing SDIO interrupt pin
pinctrl: aspeed: fix regmap error handling
pinctrl: mediatek: constify gpio_chip structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Another quiet release, a few small extensions to the set of register
maps we support and an improvement in the debugfs code:
- allow viewing of cached contents for write only registers via
debugfs.
- support a wider range of read/write flag masks in register formats.
- support more little endian formats"
* tag 'regmap-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add missing little endian functions
regmap: Allow longer flag masks for read and write
regmap: debugfs: Add support for dumping write only device registers
regmap: Add a function to check if a regmap register is cached
|
|
'regmap/topic/debugfs' into regmap-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
|
|
* pm-cpuidle:
ARM: cpuidle: Fix error return code
* pm-opp:
PM / OPP: Don't support OPP if it provides supported-hw but platform does not
PM / OPP: avoid maybe-uninitialized warning
* pm-avs:
PM / AVS: SmartReflex: Neaten logging
|
|
* pm-domains:
PM / Domains: Rename pm_genpd_sync_poweron|poweroff()
PM / Domains: Don't measure latency of ->power_on|off() during system PM
PM / Domains: Remove redundant system PM callbacks
PM / Domains: Simplify detaching a device from its genpd
PM / Domains: Allow holes in genpd_data.domains array
PM / Domains: Add support for removing nested PM domains by provider
PM / Domains: Add support for removing PM domains
PM / Domains: Store the provider in the PM domain structure
PM / Domains: Prepare for adding support to remove PM domains
PM / Domains: Verify the PM domain is present when adding a provider
PM / Domains: Don't expose xlate and provider helper functions
PM / Domains: Don't expose generic_pm_domain structure to clients
staging: board: Remove calls to of_genpd_get_from_provider()
ARM: EXYNOS: Remove calls to of_genpd_get_from_provider()
PM / Domains: Add new helper functions for device-tree
PM / Domains: Always enable debugfs support if available
|
|
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
|
|
We don't need to hold the spinlock while zeroing the allocated memory.
In case we handle big buffers this is a severe issue as other CPUs might
be spinning half a second or longer.
Signed-off-by: Bastian Hecht <bhecht@de.adit-jv.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We fix a bug in dma_mmap_from_coherent() that appears when we map non page
aligned DMA memory. It cuts off the non aligned part (this is different to
dma_alloc_coherent() that always rounds up to full pages). So for mappings
of less than a page we get -ENXIO as dma_mmap_from_coherent() assumes we
want to map zero pages.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq_get_irq_data() can return NULL, which results in a nasty crash.
Check its return value before passing it on to irqd_set_trigger_type().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OPP framework allows each OPP to set a opp-supported-hw property
which provides values that are matched against supported_hw values
provided by the platform to limit support for certain OPPs on specific
hardware. Currently, if the platform does not set supported_hw values,
all OPPs are interpreted as supported, even if they have provided their
own opp-supported-hw values.
If an OPP has provided opp-supported-hw, it is indicating that there is
some specific hardware configuration it is supported by. These constraints
should be honored, and if no supported_hw has been provided by the
platform, there is no way to determine if that OPP is actually supported,
so it should be marked as not supported.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These are internal static functions to genpd. Let's conform to the naming
rules, by dropping the "pm_" prefix from these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.
Currently genpd measures latencies in the system PM phase for the
->power_on|off() callbacks, except in the syscore case when it's not
allowed to use ktime_get() as timekeeping may be suspended.
Since there should be plenty of occasions during runtime PM to perform
these measurements, let's rely on that and drop them from system PM. This
will also make it consistent for how measurements are done of the runtime
PM callbacks (as those may be invoked during system PM).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In cases when the PM domain haven't assigned a system PM callback, the PM
core fall-backs to check for the callback at the driver level instead.
This makes it redundant to assign a pm_generic_* helper function to a
corresponding system PM callback at a PM domain level.
Therefore, let's remove these assignments in pm_genpd_init().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There's no need to validate the PM domain by using genpd_lookup_dev() when
removing the device via genpd's genpd_dev_pm_detach() function. That's
because this function can't be called, unless there is a valid PM domain
for the device.
To simplify the behaviour, let's move code from pm_genpd_remove_device()
into a new internal function, genpd_remove_device(), which is called from
pm_genpd_remove_device() and genpd_dev_pm_detach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A fix for an issue with double locking that was introduced earlier
this release. I'd missed in review that we were already in a locked
region when trying to drop part of the cache"
* tag 'regmap-fix-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix deadlock on _regmap_raw_write() error path
|
|
Linux 4.8-rc6
|
|
Commit 815806e39bf6 ("regmap: drop cache if the bus transfer error")
added a call to regcache_drop_region() to error path in
_regmap_raw_write(). However that path runs with regmap lock taken,
and regcache_drop_region() tries to re-take it, causing a deadlock.
Fix that by calling map->cache_ops->drop() directly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge urgent fixes so pending patches for 4.9 can be applied.
|
|
When CONFIG_OPTIMIZE_INLINING is set and we are building with -Wmaybe-uninitialized
enabled, we can get a warning for the opp core driver:
drivers/base/power/opp/core.c: In function 'dev_pm_opp_set_rate':
drivers/base/power/opp/core.c:560:8: warning: 'ou_volt_min' may be used uninitialized in this function [-Wmaybe-uninitialized]
This has only now appeared as a result of commit 797da5598f3a ("PM / devfreq:
Add COMPILE_TEST for build coverage"), which makes the driver visible in
some configurations that didn't have it before.
The warning is a false positive that I got with gcc-6.1.1, but there is
a simple workaround in removing the local variables that we get warnings
for (all three are affected depending on the configuration). This also
makes the code easier to read.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In platforms such as Rockchip's, the array of domains isn't always
filled without holes, as which domains are present depend on the
particular SoC revision.
By allowing holes to be in the array, such SoCs can still use a single
set of constants to index the array of power domains.
Fixes: 0159ec670763 (PM / Domains: Verify the PM domain is present when adding a provider)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This with the longer read and write masks allow supporting more
exotic devices. For example a little endian SPI device:
static const struct regmap_config foo_regmap_config = {
.reg_bits = 16,
.reg_stride = 4,
.val_bits = 16,
.write_flag_mask = 0x8000,
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
.val_format_endian = REGMAP_ENDIAN_LITTLE,
...
};
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Further testing with false negatives suppressed by commit 293e2421fe25
("rcu: Remove superfluous versions of rcu_read_lock_sched_held()")
identified a few more unprotected uses of RCU from the idle loop.
Because RCU actively ignores idle-loop code (for energy-efficiency
reasons, among other things), using RCU from the idle loop can result
in too-short grace periods, in turn resulting in arbitrary misbehavior.
The affected function is rpm_suspend().
The resulting lockdep-RCU splat is as follows:
------------------------------------------------------------------------
Warning from omap3
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc5-next-20160426+ #1112 Not tainted
-------------------------------
include/trace/events/rpm.h:63 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052ee24>] __pm_runtime_suspend+0x54/0x84
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1112
Hardware name: Generic OMAP36xx (Flattened Device Tree)
[<c0110308>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
[<c010c3a8>] (show_stack) from [<c047fec8>] (dump_stack+0xb0/0xe4)
[<c047fec8>] (dump_stack) from [<c052d7b4>] (rpm_suspend+0x604/0x7e4)
[<c052d7b4>] (rpm_suspend) from [<c052ee34>] (__pm_runtime_suspend+0x64/0x84)
[<c052ee34>] (__pm_runtime_suspend) from [<c04bf3bc>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
[<c04bf3bc>] (omap2_gpio_prepare_for_idle) from [<c01255e8>] (omap_sram_idle+0x140/0x244)
[<c01255e8>] (omap_sram_idle) from [<c0126b48>] (omap3_enter_idle_bm+0xfc/0x1ec)
[<c0126b48>] (omap3_enter_idle_bm) from [<c0601db8>] (cpuidle_enter_state+0x80/0x3d4)
[<c0601db8>] (cpuidle_enter_state) from [<c0183c74>] (cpu_startup_entry+0x198/0x3a0)
[<c0183c74>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
[<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
------------------------------------------------------------------------
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For irq spreading want to store affinity masks in the msi_entry. Add the
infrastructure for it.
We allocate an array of cpumasks with an array size of the number of used
vectors in the entry, so we can hand in the information per linux interrupt
later.
As we hand in the number of used vectors, we assign them right
away. Convert all the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1473862739-15032-2-git-send-email-hch@lst.de
|
|
strict pin controller returns -EINVAL in case of pin request which
is already claimed by somebody else.
Following is the sequence of calling pin_request() from
pinctrl_bind_pins():-
pinctrl_bind_pins()->pinctrl_select_state()->pinmux_enable_setting()->
pin_request()
But pinctrl_bind_pins() only returns -EPROBE_DEFER which makes device
driver probe successful even if the pin request is rejected by the pin
controller subsystem.
This commit modifies pinctrl_bind_pins() to return error if the pin is
rejected by pin control subsystem.
Signed-off-by: Deepak Das <deepak_das@mentor.com>
[Rewrote to be cleaner]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If a device supports PM domains that are subdomains of another PM
domain, then the PM domains should be removed in reverse order to
ensure that the subdomains are removed first. Furthermore, if there is
more than one provider, then there needs to be a way to remove the
domains in reverse order for a specific provider.
Add the function of_genpd_remove_last() to remove the last PM domain
added by a given PM domain provider and return the generic_pm_domain
structure for the PM domain that was removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The genpd framework allows users to add PM domains via the pm_genpd_init()
function, however, there is no corresponding function to remove a PM
domain. For most devices this may be fine as the PM domains are never
removed, however, for devices that wish to populate the PM domains from
within a driver, having the ability to remove a PM domain if the probing
of the device fails or the driver is unloaded is necessary.
Add the function pm_genpd_remove() to remove a PM domain by referencing
it's generic_pm_domain structure. Note that the bulk of the code that
removes the PM domain is placed in a separate local function
genpd_remove() (which is called by pm_genpd_remove()). The code is
structured in this way to prepare for adding another function to remove
a PM domain by provider that will also call genpd_remove(). Note that
users of genpd_remove() must call this function with the mutex,
gpd_list_lock, held.
PM domains can only be removed if the associated provider has been
removed, they are not a parent domain to another PM domain and have no
devices associated with them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is possible that a device has more than one provider of PM domains
and to support the removal of a PM domain by provider, it is necessary
to store a reference to the provider in the PM domain structure.
Therefore, store a reference to the firmware node handle in the PM
domain structure and populate it when providers (only device-tree based
providers are currently supported by PM domains) are registered.
Please note that when removing PM domains, it is necessary to verify
that the PM domain provider has been removed from the list of providers
before the PM domain can be removed. To do this add another member to
the PM domain structure that indicates if the provider is present and
set this member accordingly when providers are added and removed.
Initialise the 'provider' and 'has_provider' members of the
generic_pm_domain structure when a PM domains is added by calling
pm_genpd_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In order to remove PM domains safely from the list of PM domains,
it is necessary to adding locking for the PM domain list around any
places where devices or subdomains are added to a PM domain.
There are places where a reference to a PM domain is obtained via
calling of_genpd_get_from_provider() before adding the device or the
subdomain. In these cases a lock for the PM domain list needs to be
held around the call to of_genpd_get_from_provider() and the call to
add the device/subdomain. To avoid deadlocks by multiple attempts to
obtain the PM domain list lock, add functions genpd_add_device() and
genpd_add_subdomain() which require the user to hold the PM domain
list lock when calling.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When a PM domain provider is added, there is currently no way to tell if
any PM domains associated with the provider are present. Naturally, the
PM domain provider should not be registered if the PM domains have not
been added. Nonetheless, verify that the PM domain(s) associated with a
provider are present when registering the PM domain provider.
This change adds a dependency on the function pm_genpd_present() when
CONFIG_PM_GENERIC_DOMAINS_OF is enabled and so ensure this function is
available when CONFIG_PM_GENERIC_DOMAINS_OF selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Functions __of_genpd_xlate_simple(), __of_genpd_xlate_onecell() and
__of_genpd_add_provider() are not used outside of the core generic PM
domain code. Therefore, reduce the number of APIs exposed by making
these static. At the same time don't expose the typedef for
genpd_xlate_t either and make this a local definition as well.
The functions are renamed to follow the naming conventions for static
functions in the generic PM domain core.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There should be no need to expose the generic_pm_domain structure to
clients and this eliminates the need to implement reference counting for
any external reference to a PM domain. Therefore, make the functions
pm_genpd_lookup_dev() and of_genpd_get_from_provider() private to the
PM domain core. The functions are renamed in accordance with the naming
conventions for genpd static functions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Ideally, if we are returning a reference to a PM domain via a call to
of_genpd_get_from_provider(), then we should keep track of such
references via a reference count. The reference count could then be used
to determine if a PM domain can be safely removed. Alternatively, it is
possible to avoid such external references by providing APIs to access
the PM domain and hence, eliminate any calls to
of_genpd_get_from_provider().
Add new helper functions for adding a device and a subdomain to a PM
domain when using device-tree, so that external calls to
of_genpd_get_from_provider() can be removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several fixes here, the main one being the change from Lars-Peter
which I'd been letting soak in -next since the merge window in case it
uncovered further issues as it's a minimal fix rather than a change
addressing the root cause of the problems (which would've been too
invasive for -rc):
- The biggest change is a fix from Lars-Peter to ensure that we don't
create overlapping rbtree nodes which in turn avoids returning
corrupt cache values to users, fixing some issues that were exposed
by some recent optimisations with certain access patterns but had
been present for a long time.
- A fix from Elaine Zhang to stop us updating the cache if we get an
I/O error when writing to the hardware.
- A fix fromm Maarten ter Huurne to avoid uninitialized defaults in
cases where we have non-readable registers but are initializing the
cache by reading from the device"
* tag 'regmap-fix-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: drop cache if the bus transfer error
regmap: rbtree: Avoid overlapping nodes
regmap: cache: Fix num_reg_defaults computation from reg_defaults_raw
|
|
We want the sysfs and kernfs in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
The workqueue "deferred_wq" queues a single work item
&deferred_probe_work and hence doesn't require ordering.
It is involved in probing devices and is not being used on a memory
reclaim path. Hence, it has been converted to use system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item has been flushed in driver_probe_done() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dmam_declare_coherent_memory doesn't take into account the return
value of dma_declare_coherent_memory, which leads to incorrect resource
handling
Signed-off-by: Vyacheslav V. Yurkov <uvv.mail@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_irq_get[_byname]() return 0 iff irq_create_of_mapping() call fails.
Returning both error code and 0 on failure is a sign of a misdesigned API,
it makes the failure check unnecessarily complex and error prone. We should
rely on the platform IRQ resource in this case, not return 0, especially
as 0 can be a valid IRQ resource too...
Fixes: aff008ad813c ("platform_get_irq: Revert to platform_get_resource if of_irq_get fails")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch could reduce one branch in this function. Also
make the code more readble.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
To: linux-kernel@vger.kernel.org
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace explicit computation of vma page count by a call to
vma_pages()
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace explicit computation of vma page count by a call to
vma_pages()
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 't' in "function" was missing, this patch fixes this typo:
s/funcion/function/g
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/base/Kconfig:config SOC_BUS
drivers/base/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When dma_common_free_remap, the input parameter 'size' may not
be page aligned. And, met kernel warning when doing iommu dma
for usb on i.MX8 platform:
"
WARNING: CPU: 0 PID: 869 at mm/vmalloc.c:70 vunmap_page_range+0x1cc/0x1d0()
Modules linked in:
CPU: 0 PID: 869 Comm: kworker/u8:2 Not tainted 4.1.12-00444-gc5f9d1d-dirty #147
Hardware name: Freescale i.MX8DV Sabreauto (DT)
Workqueue: ci_otg ci_otg_work
Call trace:
[<ffffffc000089920>] dump_backtrace+0x0/0x124
[<ffffffc000089a54>] show_stack+0x10/0x1c
[<ffffffc0006d1e6c>] dump_stack+0x84/0xc8
[<ffffffc0000b4568>] warn_slowpath_common+0x98/0xd0
[<ffffffc0000b4664>] warn_slowpath_null+0x14/0x20
[<ffffffc000170348>] vunmap_page_range+0x1c8/0x1d0
[<ffffffc000170388>] unmap_kernel_range+0x20/0x88
[<ffffffc000460ad0>] dma_common_free_remap+0x74/0x84
[<ffffffc0000940d8>] __iommu_free_attrs+0x9c/0x178
[<ffffffc0005032bc>] ehci_mem_cleanup+0x140/0x194
[<ffffffc000503548>] ehci_stop+0x8c/0xdc
[<ffffffc0004e8258>] usb_remove_hcd+0xf0/0x1cc
[<ffffffc000516bc0>] host_stop+0x1c/0x58
[<ffffffc000514240>] ci_otg_work+0xdc/0x120
[<ffffffc0000c9c34>] process_one_work+0x134/0x33c
[<ffffffc0000c9f78>] worker_thread+0x13c/0x47c
[<ffffffc0000cf43c>] kthread+0xd8/0xf0
"
For dma_common_pages_remap:
dma_common_pages_remap
|->get_vm_area_caller
|->__get_vm_area_node
|->size = PAGE_ALIGN(size); Round up to page aligned
So, in dma_common_free_remap, we also need a page aligned size,
pass 'PAGE_ALIGN(size)' to unmap_kernel_range.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
