| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
|
|
Support for adding per-device frequency limits was removed in
commit 2aac8bdf7a0f ("PM: QoS: Drop frequency QoS types from device PM QoS")
after cpufreq switched to use a new "freq_constraints" construct.
Restore support for per-device freq limits but base this upon
freq_constraints. This is primarily meant to be used by the devfreq
subsystem.
This removes the "static" marking on freq_qos_apply but does not export
it for modules.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The pm_qos family of APIs are used in relatively difficult to reproduce
scenarios such as thermal throttling so they benefit from unit testing.
Start by adding basic tests from the the freq_qos APIs. It includes
tests for issues that were brought up on mailing lists:
https://patchwork.kernel.org/patch/11252425/#23017005
https://patchwork.kernel.org/patch/11253421/
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-sleep:
PM / wakeirq: remove unnecessary parentheses
PM / core: Clean up some function headers in power.h
PM / hibernate: memory_bm_find_bit(): Tighten node optimisation
* pm-domains:
PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
PM / Domains: Implement the ->start() callback for genpd
PM / Domains: Introduce dev_pm_domain_start()
* pm-opp:
PM / OPP: Support adjusting OPP voltages at runtime
* powercap:
powercap/intel_rapl: add support for Cometlake desktop
powercap/intel_rapl: add support for CometLake Mobile
|
|
The intent with walking the gpd_list via calling genpd_present() from
genpd_syscore_switch(), is to make sure the dev->pm_domain pointer belongs
to a registered genpd. However, as a genpd can't be removed if there is a
device attached to it, let's convert to use the quicker dev_to_genpd_safe()
instead.
Due to the above change, this allows us to clean up genpd_present() and
move it inside CONFIG_PM_GENERIC_DOMAINS_OF, so let's do that as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To allow a subsystem/driver to explicitly start its device from genpd's
point view, let's implement the ->start() callback in the struct
dev_pm_domain that corresponds to the genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For a subsystem/driver that either doesn't support runtime PM or makes use
of pm_runtime_set_active() during ->probe(), may try to access its device
when probing, even if it may not be fully powered on from the PM domain's
point of view. This may be the case when the used PM domain is a genpd
provider, that implements genpd's ->start|stop() device callbacks.
There are cases where the subsystem/driver managed to avoid the above
problem, simply by calling pm_runtime_enable() and pm_runtime_get_sync()
during ->probe(). However, this approach comes with a drawback, especially
if the subsystem/driver implements a ->runtime_resume() callback.
More precisely, the subsystem/driver then needs to use a device flag, which
is checked in its ->runtime_resume() callback, as to avoid powering on its
resources the first time the callback is invoked. This is needed because
the subsystem/driver has already powered on the resources for the device,
during ->probe() and before it called pm_runtime_get_sync().
In a way to avoid this boilerplate code and the inefficient check for "if
(first_time_suspend)" in the ->runtime_resume() callback for these
subsystems/drivers, let's introduce and export a dev_pm_domain_start()
function, that may be called during ->probe() instead.
Moreover, let the dev_pm_domain_start() invoke an optional ->start()
callback, added to the struct dev_pm_domain, as to allow a PM domain
specific implementation.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove unnecessary parentheses found by code review.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The power.h is a bit messy due to the various existing CONFIG_PM* Kconfig
combinations. However the final section for wakeup_source_sysfs*() can be
moved inside one of the existing sections rather than adding yet another
one, so let's do that to clean up the code a little bit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some user might want to go through all registered wakeup sources
and doing things accordingly. For example, SoC PM driver might need to
do HW programming to prevent powering down specific IP which wakeup
source depending on. So add this API to help walk through all registered
wakeup source objects on that list and return them one by one.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
|
|
There are no more active users of DEV_PM_QOS_MIN_FREQUENCY and
DEV_PM_QOS_MAX_FREQUENCY device PM QoS request types, so drop them
along with the code supporting them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much
discussion and review and a day-long in-person meeting, they were
decided to be reverted and a new set of patches is currently being
reviewed on the mailing list.
Other than that churn, there are two "persistent" branches in here
that other trees will be pulling in as well during the merge window.
One branch to add support for drivers to have the driver core
automatically add sysfs attribute files when a driver is bound to a
device so that the driver doesn't have to manually do it (and then
clean it up, as it always gets it wrong).
There's another branch in here for generic lookup helpers for the
driver core that lots of busses are starting to use. That's the
majority of the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to
hopefully get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues"
[ Note that the above-mentioned generic lookup helpers branch was
already brought in by the LED merge (commit 4feaab05dc1e) that had
shared it.
Also note that that common branch introduced an i2c bug due to a bad
conversion, which got fixed here. - Linus ]
* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
coccinelle: platform_get_irq: Fix parse error
driver-core: add include guard to linux/container.h
sysfs: add BIN_ATTR_WO() macro
driver core: platform: Export platform_get_irq_optional()
hwmon: pwm-fan: Use platform_get_irq_optional()
driver core: platform: Introduce platform_get_irq_optional()
Revert "driver core: Add support for linking devices during device addition"
Revert "driver core: Add edit_links() callback for drivers"
Revert "of/platform: Add functional dependency link from DT bindings"
Revert "driver core: Add sync_state driver/bus callback"
Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
Revert "of/platform: Create device links for all child-supplier depencencies"
Revert "of/platform: Don't create device links for default busses"
Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
Revert "of/platform: Disable generic device linking code for PowerPC"
devcoredump: fix typo in comment
devcoredump: use memory_read_from_buffer
of/platform: Disable generic device linking code for PowerPC
device.h: Fix warnings for mismatched parameter names in comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
|
|
* pm-opp:
PM / OPP: Correct Documentation about library location
opp: of: Support multiple suspend OPPs defined in DT
dt-bindings: opp: Support multiple opp-suspend properties
opp: core: add regulators enable and disable
opp: Don't decrement uninitialized list_kref
* pm-qos:
PM: QoS: Get rid of unused flags
* acpi-pm:
ACPI: PM: Print debug messages on device power state changes
* pm-domains:
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
PM / Domains: Align in-parameter names for some genpd functions
* pm-tools:
pm-graph: make setVal unbuffered again for python2 and python3
cpupower: update German translation
tools/power/cpupower: fix 64bit detection when cross-compiling
cpupower: Add missing newline at end of file
pm-graph v5.5
|
|
* pm-s2idle-rework: (21 commits)
ACPI: PM: s2idle: Always set up EC GPE for system wakeup
ACPI: PM: s2idle: Avoid rearming SCI for wakeup unnecessarily
PM: suspend: Fix platform_suspend_prepare_noirq()
intel-hid: Disable button array during suspend-to-idle
intel-hid: intel-vbtn: Avoid leaking wakeup_mode set
ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices
ACPI: EC: PM: Make acpi_ec_dispatch_gpe() print debug message
ACPI: EC: PM: Consolidate some code depending on PM_SLEEP
ACPI: PM: s2idle: Eliminate acpi_sleep_no_ec_events()
ACPI: PM: s2idle: Switch EC over to polling during "noirq" suspend
ACPI: PM: s2idle: Add acpi.sleep_no_lps0 module parameter
ACPI: PM: s2idle: Rearrange lps0_device_attach()
ACPI: PM: Set up EC GPE for system wakeup from drivers that need it
PM: sleep: Drop dpm_noirq_begin() and dpm_noirq_end()
PM: sleep: Integrate suspend-to-idle with generig suspend flow
PM: sleep: Simplify suspend-to-idle control flow
ACPI: PM: Set s2idle_wakeup earlier and clear it later
PM: sleep: Fix possible overflow in pm_system_cancel_wakeup()
ACPI: EC: Return bool from acpi_ec_dispatch_gpe()
ACPICA: Return u32 from acpi_dispatch_gpe()
...
|
|
The dev_pm_genpd_set_performance_state() could in principle be called for a
device that has a different PM domain type attached than a genpd. This
would lead to a problem as dev_to_genpd() uses the container_of macro.
Address this problem by using dev_to_genpd_safe() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
genpd_lookup_dev(), is a bit unnecessary heavy, as it walks the gpd_list to
try to find a valid PM domain corresponding to the device's attached genpd.
Instead of walking the gpd_list, let's use the fact that a genpd always has
the ->runtime_suspend() callback assigned to the genpd_runtime_suspend()
function.
While changing this, let's take the opportunity to also rename
genpd_lookup_dev(), into dev_to_genpd_safe() to better reflect its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These functions are just used by the PM core, and that isn't modular so
these functions don't need to be exported. Drop the exports.
Fixes: c8377adfa781 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reviewed-by: Tri Vo <trong@android.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The device_set_wakeup_enable() function can be called on a device that
hasn't been registered with device_add() yet. This allows the device to
be in a state where wakeup is enabled for it but the device isn't
published to userspace in sysfs yet.
After commit c8377adfa781 ("PM / wakeup: Show wakeup sources stats in
sysfs"), calling device_set_wakeup_enable() will fail for a device that
hasn't been registered with the driver core via device_add(). This is
because we try to create sysfs entries for the device and associate a
wakeup class kobject with it before the device has been registered.
Let's follow a similar approach that device_set_wakeup_capable() takes
here and register the wakeup class either from
device_set_wakeup_enable() when the device is already registered, or
from dpm_sysfs_add() when the device is being registered with the driver
core via device_add().
Fixes: c8377adfa781 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tri Vo <trong@android.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We shouldn't call wakeup_source_destroy() from the error path in
wakeup_source_register() because that calls __pm_relax() which takes a
lock that isn't initialized until wakeup_source_add() is called. Add a
new function, wakeup_source_free(), that just does the bare minimum to
free a wakeup source that was created but hasn't been added yet and use
it from the two places it's needed. This fixes the following problem
seen on various x86 server boxes:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 12 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc4-
Hardware name: HP ProLiant XL420 Gen9/ProLiant XL420 Gen9, BIOS U19 12/27/2015
Call Trace:
dump_stack+0x62/0x9a
register_lock_class+0x95a/0x960
? __platform_driver_probe+0xcd/0x230
? __platform_create_bundle+0xc0/0xe0
? i8042_init+0x4ec/0x578
? do_one_initcall+0xfe/0x45a
? kernel_init_freeable+0x614/0x6a7
? kernel_init+0x11/0x138
? ret_from_fork+0x35/0x40
? is_dynamic_key+0xf0/0xf0
? rwlock_bug.part.0+0x60/0x60
? __debug_check_no_obj_freed+0x8e/0x250
__lock_acquire.isra.13+0x5f/0x830
? __debug_check_no_obj_freed+0x152/0x250
lock_acquire+0x107/0x220
? __pm_relax.part.2+0x21/0xa0
_raw_spin_lock_irqsave+0x35/0x50
? __pm_relax.part.2+0x21/0xa0
__pm_relax.part.2+0x21/0xa0
wakeup_source_destroy.part.3+0x18/0x190
wakeup_source_register+0x43/0x50
Fixes: c8377adfa781 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add an ID and a device pointer to 'struct wakeup_source'. Use them to to
expose wakeup sources statistics in sysfs under
/sys/class/wakeup/wakeup<ID>/*.
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tri Vo <trong@android.com>
Tested-by: Kalesh Singh <kaleshsingh@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
wakeup_source_init() has no users. Remove it.
As a result, wakeup_source_prepare() is only called from
wakeup_source_create(). Merge wakeup_source_prepare() into
wakeup_source_create() and remove it.
Change wakeup_source_create() behavior so that assigning NULL to wakeup
source's name throws an error.
Signed-off-by: Tri Vo <trong@android.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This commit applies the consolidated hlist_for_each_entry_rcu() support
for lockdep conditions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
|
|
If device_link_add() is called for a consumer/supplier pair with an
existing device link between them and the existing link's type is
not in agreement with the flags passed to that function by its
caller, NULL will be returned. That is seriously inconvenient,
because it forces the callers of device_link_add() to worry about
what others may or may not do even if that is not relevant to them
for any other reasons.
It turns out, however, that this limitation can be made go away
relatively easily.
The underlying observation is that if DL_FLAG_STATELESS has been
passed to device_link_add() in flags for the given consumer/supplier
pair at least once, calling either device_link_del() or
device_link_remove() to release the link returned by it should work,
but there are no other requirements associated with that flag. In
turn, if at least one of the callers of device_link_add() for the
given consumer/supplier pair has not passed DL_FLAG_STATELESS to it
in flags, the driver core should track the status of the link and act
on it as appropriate (ie. the link should be treated as "managed").
This means that DL_FLAG_STATELESS needs to be set for managed device
links and it should be valid to call device_link_del() or
device_link_remove() to drop references to them in certain
sutiations.
To allow that to happen, introduce a new (internal) device link flag
called DL_FLAG_MANAGED and make device_link_add() set it automatically
whenever DL_FLAG_STATELESS is not passed to it. Also make it take
additional references to existing device links that were previously
stateless (that is, with DL_FLAG_STATELESS set and DL_FLAG_MANAGED
unset) and will need to be managed going forward and initialize
their status (which has been DL_STATE_NONE so far).
Accordingly, when a managed device link is dropped automatically
by the driver core, make it clear DL_FLAG_MANAGED, reset the link's
status back to DL_STATE_NONE and drop the reference to it associated
with DL_FLAG_MANAGED instead of just deleting it right away (to
allow it to stay around in case it still needs to be released
explicitly by someone).
With that, since setting DL_FLAG_STATELESS doesn't mean that the
device link in question is not managed any more, replace all of the
status-tracking checks against DL_FLAG_STATELESS with analogous
checks against DL_FLAG_MANAGED and update the documentation to
reflect these changes.
While at it, make device_link_add() reject flags that it does not
recognize, including DL_FLAG_MANAGED.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Review-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/2305283.AStDPdUUnE@kreacher
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Note that after previous changes dpm_noirq_begin() and
dpm_noirq_end() each have only one caller, so move the code from
them to their respective callers and drop them.
Also note that dpm_noirq_resume_devices() and
dpm_noirq_suspend_devices() need not be exported any more, so make
them both static.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
After commit 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e22011856f ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
It is not actually guaranteed that pm_abort_suspend will be
nonzero when pm_system_cancel_wakeup() is called which may lead to
subtle issues, so make it use atomic_dec_if_positive() instead of
atomic_dec() for the safety sake.
Fixes: 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
* pm-cpufreq:
cpufreq: Make cpufreq_generic_init() return void
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Add QoS requests for userspace constraints
cpufreq: intel_pstate: Reuse refresh_frequency_limits()
cpufreq: Register notifiers with the PM QoS framework
PM / QoS: Add support for MIN/MAX frequency constraints
PM / QOS: Pass request type to dev_pm_qos_read_value()
PM / QOS: Rename __dev_pm_qos_read_value() and dev_pm_qos_raw_read_value()
PM / QOS: Pass request type to dev_pm_qos_{add|remove}_notifier()
|
|
* pm-opp:
opp: Don't use IS_ERR on invalid supplies
opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes
opp: Don't overwrite rounded clk rate
opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()
opp: Attach genpds to devices from within OPP core
* pm-misc:
PM / clk: Remove error message on out-of-memory condition
drivers: base: power: clock_ops: Use of_clk_get_parent_count()
* pm-avs:
power: avs: smartreflex: no need to check return value of debugfs_create functions
* pm-tools:
cpupower : frequency-set -r option misses the last cpu in related cpu list
cpupower: correct spelling of interval
Add README and update pm-graph and sleepgraph docs
Update to pm-graph 5.4
Update to pm-graph 5.3
|
|
After recent hibernation-related changes, there are no more callers
of dev_pm_skip_next_resume_phases() except for the PM core itself
in which it is more straightforward to run the statements from
that function directly, so do that and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This patch introduces the min-frequency and max-frequency device
constraints, which will be used by the cpufreq core to begin with.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In order to allow dev_pm_qos_read_value() to read values for different
QoS requests, pass request type as a parameter to these routines.
For now, it only supports resume-latency request type but will be
extended to frequency limit (min/max) constraints later on.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
dev_pm_qos_read_value() will soon need to support more constraint types
(min/max frequency) and will have another argument to it, i.e. type of
the constraint. While that is fine for the existing users of
dev_pm_qos_read_value(), but not that optimal for the callers of
__dev_pm_qos_read_value() and dev_pm_qos_raw_read_value() as all the
callers of these two routines are only looking for resume latency
constraint.
Lets make these two routines care only about the resume latency
constraint and rename them to __dev_pm_qos_resume_latency() and
dev_pm_qos_raw_resume_latency().
Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In order to use the same set of routines to register notifiers for
different request types, update the existing
dev_pm_qos_{add|remove}_notifier() routines with an additional
parameter: request-type.
For now, it only supports resume-latency request type but will be
extended to frequency limit (min/max) constraints later on.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
wakeup_sources_stats_dentry is assigned when the debugfs file is
created, but then never used ever again. So no need for it at all, just
remove it and call debugfs_create_file() on its own.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When debugging device driver power management code it is convenient to
know how much time is spent in the "suspend start" and "suspend end"
phases. Hence log the time spent in these phases.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is no need to print an error message if kstrdup() fails, as the
memory allocation core already takes care of that.
Note that commit 59d84ca8c46a93ad ("PM / OPP / clk: Remove unnecessary
OOM message") already removed similar error messages, but this one was
forgotten.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use of_clk_get_parent_count() instead of open coding.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix a recent regression causing kernels built with CONFIG_PM
unset to crash on systems that support the Performance and Energy Bias
Hint (EPB), clean up the cpufreq core and some users of transition
notifiers and introduce a new power domain flag into the generic power
domains framework (genpd).
Specifics:
- Fix recent regression causing kernels built with CONFIG_PM unset to
crash on systems that support the Performance and Energy Bias Hint
(EPB) by avoiding to compile the EPB-related code depending on
CONFIG_PM when it is unset (Rafael Wysocki).
- Clean up the transition notifier invocation code in the cpufreq
core and change some users of cpufreq transition notifiers
accordingly (Viresh Kumar).
- Change MAINTAINERS to cover the schedutil governor as part of
cpufreq (Viresh Kumar).
- Simplify cpufreq_init_policy() to avoid redundant computations (Yue
Hu).
- Add explanatory comment to the cpufreq core (Rafael Wysocki).
- Introduce a new flag, GENPD_FLAG_RPM_ALWAYS_ON, to the generic
power domains (genpd) framework along with the first user of it
(Leonard Crestez)"
* tag 'pm-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
soc: imx: gpc: Use GENPD_FLAG_RPM_ALWAYS_ON for ERR009619
PM / Domains: Add GENPD_FLAG_RPM_ALWAYS_ON flag
cpufreq: Update MAINTAINERS to include schedutil governor
cpufreq: Don't find governor for setpolicy drivers in cpufreq_init_policy()
cpufreq: Explain the kobject_put() in cpufreq_policy_alloc()
cpufreq: Call transition notifier only once for each policy
x86: intel_epb: Take CONFIG_PM into account
|
|
This is for power domains which can only be powered off for suspend but
not as part of runtime PM.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow state reset of printk_once() calls.
- Prevent crashes when dereferencing invalid pointers in vsprintf().
Only the first byte is checked for simplicity.
- Make vsprintf warnings consistent and inlined.
- Treewide conversion of obsolete %pf, %pF to %ps, %pF printf
modifiers.
- Some clean up of vsprintf and test_printf code.
* tag 'printk-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Make function pointer_string static
vsprintf: Limit the length of inlined error messages
vsprintf: Avoid confusion between invalid address and value
vsprintf: Prevent crash when dereferencing invalid pointers
vsprintf: Consolidate handling of unknown pointer specifiers
vsprintf: Factor out %pO handler as kobject_string()
vsprintf: Factor out %pV handler as va_format()
vsprintf: Factor out %p[iI] handler as ip_addr_string()
vsprintf: Do not check address of well-known strings
vsprintf: Consistent %pK handling for kptr_restrict == 0
vsprintf: Shuffle restricted_pointer()
printk: Tie printk_once / printk_deferred_once into .data.once for reset
treewide: Switch printk users from %pf and %pF to %ps and %pS, respectively
lib/test_printf: Switch to bitmap_zalloc()
|
|
* pm-devfreq:
PM / devfreq: add tracing for scheduling work
trace: events: add devfreq trace event file
PM / devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.
PM / devfreq: rockchip-dfi: Move GRF definitions to a common place.
PM / devfreq: exynos-bus: Suspend all devices on system shutdown
PM / devfreq: Fix static checker warning in try_then_request_governor
PM / devfreq: Restart previous governor if new governor fails to start
PM / devfreq: tegra: remove unneeded variable
PM / devfreq: rockchip-dfi: remove unneeded semicolon
PM / devfreq: rk3399_dmc: remove unneeded semicolon
PM / devfreq: consistent indentation
PM / devfreq: fix missing check of return value in devfreq_add_device()
PM / devfreq: fix mem leak in devfreq_add_device()
PM / devfreq: Use of_node_name_eq for node name comparisons
* pm-domains:
PM / Domains: Allow to attach a CPU via genpd_dev_pm_attach_by_id|name()
PM / Domains: Search for the CPU device outside the genpd lock
PM / Domains: Drop unused in-parameter to some genpd functions
PM / Domains: Use the base device for driver_deferred_probe_check_state()
PM / Domains: Enable genpd_dev_pm_attach_by_id|name() for single PM domain
PM / Domains: Allow OF lookup for multi PM domain case from ->attach_dev()
PM / Domains: Don't kfree() the virtual device in the error path
PM / Domains: remove unnecessary unlikely()
|
|
* pm-cpuidle:
PM / Domains: Add genpd governor for CPUs
cpuidle: Export the next timer expiration for CPUs
PM / Domains: Add support for CPU devices to genpd
PM / Domains: Add generic data pointer to struct genpd_power_state
cpuidle: exynos: Unify target residency for AFTR and coupled AFTR states
* pm-sleep:
PM / core: Propagate dev->power.wakeup_path when no callbacks
PM / core: Introduce dpm_async_fn() helper
PM / core: fix kerneldoc comment for device_pm_wait_for_dev()
PM / core: fix kerneldoc comment for dpm_watchdog_handler()
PM / sleep: Measure the time of filesystems syncing
PM / sleep: Refactor filesystems sync to reduce duplication
PM / wakeup: Use pm_pr_dbg() instead of pr_debug()
|
|
Attaching a device via genpd_dev_pm_attach_by_id|name() makes
genpd allocate a virtual device that it attaches instead. This
leads to a problem in case when the base device belongs to a CPU.
More precisely, it means genpd_get_cpu() compares against the
virtual device, thus it fails to find a matching CPU device.
Address this limitation by passing the base device to genpd_get_cpu()
rather than the virtual device.
Moreover, to deal with detach correctly from genpd_remove_device(),
store the CPU number in struct generic_pm_domain_data, so as to be
able to clear the corresponding bit in the cpumask for the genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
While attaching/detaching a device to a PM domain (genpd) with
GENPD_FLAG_CPU_DOMAIN set, genpd iterates the cpu_possible_mask to
check whether or not the device corresponds to a CPU. This iteration
is done while holding the genpd's lock, which is unnecessary.
Avoid the locking by restructuring the corresponding code a bit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Both genpd_alloc_dev_data() and genpd_add_device(), that are internal
genpd functions, allow a struct gpd_timing_data *td to be passed as an
in-parameter. However, as NULL is always passed, let's just drop the
in-parameter altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When genpd fails to attach a device to one of its multiple PM domains,
we end up calling driver_deferred_probe_check_state() for the recently
allocated virtual device. This is incorrect, as it's the base device
that is being probed.
Fix this by passing along the base device to __genpd_dev_pm_attach()
and use that instead.
Fixes: e01afc325025 ("PM / Domains: Stop deferring probe at the end of initcall")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
If a call to dev_pm_domain_attach() succeeds to attach a device to its
single PM domain, the important point is to prevent subsequent
dev_pm_domain_attach_by_name|id() calls from failing. That is done by
checking the dev->pm_domain pointer and then returning -EEXIST, rather
than continuing to call genpd_dev_pm_attach_by_id|name().
For this reason, enable genpd_dev_pm_attach_by_id|name() to be used for
single PM domains too. This simplifies future users, so they only need
to use dev_pm_domain_attach_by_id|name() instead of having to combine
it with dev_pm_domain_attach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
