summaryrefslogtreecommitdiffstats
path: root/drivers/ata/sata_highbank.c
AgeCommit message (Collapse)AuthorFilesLines
2018-04-26libahci: Allow drivers to override stop_engineEvan Wang1-1/+1
Marvell armada37xx, armada7k and armada8k share the same AHCI sata controller IP, and currently there is an issue (Errata Ref#226)that the SATA can not be detected via SATA Port-MultiPlayer(PMP). After debugging, the reason is found that the value of Port-x FIS-based Switching Control (PxFBS@0x40) became wrong. According to design, the bits[11:8, 0] of register PxFBS are cleared when Port Command and Status (0x18) bit[0] changes its value from 1 to 0, i.e. falling edge of Port Command and Status bit[0] sends PULSE that resets PxFBS bits[11:8; 0]. So it needs save the port PxFBS register before PxCMD ST write and restore the port PxFBS register afterwards in ahci_stop_engine(). This commit allows drivers to override ahci_stop_engine behavior for use by the Marvell AHCI driver(and potentially other drivers in the future). Signed-off-by: Evan Wang <xswang@marvell.com> Cc: Ofer Heifetz <oferh@marvell.com> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2016-05-27remove lots of IS_ERR_VALUE abusesArnd Bergmann1-1/+1
Most users of IS_ERR_VALUE() in the kernel are wrong, as they pass an 'int' into a function that takes an 'unsigned long' argument. This happens to work because the type is sign-extended on 64-bit architectures before it gets converted into an unsigned type. However, anything that passes an 'unsigned short' or 'unsigned int' argument into IS_ERR_VALUE() is guaranteed to be broken, as are 8-bit integers and types that are wider than 'unsigned long'. Andrzej Hajda has already fixed a lot of the worst abusers that were causing actual bugs, but it would be nice to prevent any users that are not passing 'unsigned long' arguments. This patch changes all users of IS_ERR_VALUE() that I could find on 32-bit ARM randconfig builds and x86 allmodconfig. For the moment, this doesn't change the definition of IS_ERR_VALUE() because there are probably still architecture specific users elsewhere. Almost all the warnings I got are for files that are better off using 'if (err)' or 'if (err < 0)'. The only legitimate user I could find that we get a warning for is the (32-bit only) freescale fman driver, so I did not remove the IS_ERR_VALUE() there but changed the type to 'unsigned long'. For 9pfs, I just worked around one user whose calling conventions are so obscure that I did not dare change the behavior. I was using this definition for testing: #define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \ unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO)) which ends up making all 16-bit or wider types work correctly with the most plausible interpretation of what IS_ERR_VALUE() was supposed to return according to its users, but also causes a compile-time warning for any users that do not pass an 'unsigned long' argument. I suggested this approach earlier this year, but back then we ended up deciding to just fix the users that are obviously broken. After the initial warning that caused me to get involved in the discussion (fs/gfs2/dir.c) showed up again in the mainline kernel, Linus asked me to send the whole thing again. [ Updated the 9p parts as per Al Viro - Linus ] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Andrew Morton <akpm@linux-foundation.org> Link: https://lkml.org/lkml/2016/1/7/363 Link: https://lkml.org/lkml/2016/5/27/486 Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-06-03ahci: Store irq number in struct ahci_host_privRobert Richter1-1/+2
Currently, ahci supports only msi and intx. To also support msix the handling of the irq number need to be changed. The irq number for msix devices is taken from msi_list instead of pci_dev. Thus, the irq number of a device needs to be stored in struct ahci_host_priv now. This allows the host controller to be activated in a generic way. This change is only intended for ahci drivers. For that reason the irq number is stored in struct ahci_host_priv used only by ahci drivers. Thus, the ABI changes only for ahci_host_activate(), but existing ata drivers (about 50) are unaffected and keep unchanged. All users of ahci_host_activate() have been updated. While touching drivers/ata/libahci.c, doing a small code cleanup in ahci_port_start(). Signed-off-by: Robert Richter <rrichter@cavium.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-10-20ata: drop owner assignment from platform_driversWolfram Sang1-1/+0
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-06AHCI: Move host activation code into ahci_host_activate()Alexander Gordeev1-2/+1
Currently host activation done by calling either function ahci_host_activate() or ata_host_activate(). Consolidate the code by only calling ahci_host_activate() for all AHCI devices. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: linux-ide@vger.kernel.org
2014-07-30ata: libahci_platform: move port_map parameters into the AHCI structureAntoine Ténart1-1/+1
This patch moves force_port_map and mask_port_map into the ahci_host_priv structure. This allows to modify them into the AHCI framework. This is needed by the new dt bindings representing ports as the port_map mask is computed automatically. Parameters modifying force_port_map, mask_port_map and flags have been removed from the ahci_platform_init_host() function, and inputs in the ahci_host_priv structure are now directly filed. Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-03-26ata: sata_highbank: remove superfluous castBartlomiej Zolnierkiewicz1-1/+1
hpriv->plat_data is 'void *' so there is no need to cast it to 'struct ecx_plat_data *'. Cc: Mark Langsdorf <mark.langsdorf@calxeda.com> Cc: Rob Herring <robh@kernel.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-02-22libahci: Allow drivers to override start_engineHans de Goede1-1/+2
Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a special register to be poked before starting the DMA engine. This register gets reset on an ahci_stop_engine call, so there is no other place then ahci_start_engine where this poking can be done. This commit allows drivers to override ahci_start_engine behavior for use by the Allwinner AHCI driver (and potentially other drivers in the future). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-02-13ata: delete non-required instances of include <linux/init.h>Paul Gortmaker1-1/+0
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. Cc: linux-ide@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-19sata-highbank: Remove unnecessary ahci_platform.h includeHans de Goede1-1/+0
The sata-highbank driver is a complete standalone sata driver, which does not use ahci_platform.c / ahci_platform_data in any way. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-10-27sata_highbank: clear whole array in highbank_initialize_phys()Dan Carpenter1-5/+3
The original code used the wrong parameter to clear tx_atten[]. It passed the number of elements instead of sizeof() the array to memset. The other potential issue was that cphy_base[] wasn't cleared. I'm not sure if that was a real problem or not, but I have cleared it in my patch. Instead of using memset(), this patch uses empty initializers as a cleanup. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-09-03Merge branch 'for-3.12' of ↵Linus Torvalds1-13/+61
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata Pull libata changes from Tejun Heo: "Two interesting changes. - libata acpi handling has been restructured so that the association between ata devices and ACPI handles are less convoluted. This change shouldn't change visible behavior. - Queued TRIM support, which enables sending TRIM to the device without draining in-flight RW commands, is added. Currently only enabled for ahci (and likely to stay that way for the foreseeable future). Other changes are driver-specific updates / fixes" * 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: libata: bugfix: Remove __le32 in ata_tf_to_fis() libata: acpi: Remove ata_dev_acpi_handle stub in libata.h libata: Add support for queued DSM TRIM libata: Add support for SEND/RECEIVE FPDMA QUEUED libata: Add H2D FIS "auxiliary" port flag libata: Populate host-to-device FIS "auxiliary" field ata: acpi: rework the ata acpi bind support sata, highbank: send extra clock cycles in SGPIO patterns sata, highbank: set tx_atten override bits devicetree: create a separate binding description for sata_highbank drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource sata highbank: enable 64-bit DMA mask when using LPAE ata: pata_samsung_cf: add missing __iomem annotation ata: pata_arasan: Staticize local symbols sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs ata: use dev_get_platdata() sata_mv: Remove unneeded forward declaration libata: acpi: remove dead code for ata_acpi_(un)bind libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
2013-08-14sata, highbank: send extra clock cycles in SGPIO patternsMark Langsdorf1-0/+13
Some SGPIO PICs don't follow the standard very well and expect a certain number of clock cycles or port frames in each SGPIO pattern. Add two optional parameters in the DTB that can provide the number of extra clock cycles to be sent before and after SGPIO pattern. Read those parameters from the DTB and send the extra clock cycles. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-08-14sata, highbank: set tx_atten override bitsMark Langsdorf1-13/+45
Some board designs do not drive the SATA transmit lines within the specification. The ECME can provide override settings, on a per board basis, to bring the transmit lines within spec. Read those settings from the DTB and program them in. At the time of submission, no production hardware requires this patch. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-08-09sata highbank: enable 64-bit DMA mask when using LPAERob Herring1-0/+3
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-08-09sata, highbank: fix ordering of SGPIO signalsMark Langsdorf1-2/+2
The ACTIVITY and ERROR signals were reversed in the original commit. Fix that so that hard drive activity does not show up on the error light, and attempts to indicate that the hard drive is failing do not show up as hard drive activity. This fixes a fairly serious functional bug in the driver, but failing to apply this patch will not cause any stability issues on the system. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2013-07-02Merge branch 'libata/for-3.10-fixes' into libata/for-3.11Tejun Heo1-2/+18
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge it into for-3.11 so that it can be routed together with other changes scheduled for v3.11. Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by 1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions") conflicting with logic updates in for-3.10-fixes. The offending commit simply adds local variable @base on functions which dereferences sata_rcar_priv->base multiple times. The resolutions are trivial - applying s/priv->base/base/ in the conflicting logic updates. Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-06sata highbank: add bit-banged SGPIO driver supportMark Langsdorf1-6/+155
Highbank supports SGPIO by bit-banging out the SGPIO signals over three GPIO pins defined in the DTB. Add support for this SGPIO functionality. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-06-03sata_highbank: increase retry count but shorten duration for Calxeda controllerMark Langsdorf1-2/+18
Increase the retry count for the hard reset function to 100 but shorten the time out period to 500 ms. See the comment for ahci_highbank_hardreset for the reasons why those vaulues were chosen. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2013-04-30sata_highbank: Rename proc_name to the module nameRobert Richter1-1/+1
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find the module name of a disk driver. Current name is "highbank-ahci" but the module is "sata_highbank". Rename it to match the module name. Cc: Rob Herring <rob.herring@calxeda.com> Cc: Alexander Graf <agraf@suse.de> Cc: <stable@vger.kernel.org> v3.7.. Signed-off-by: Robert Richter <robert.richter@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-04-03sata_highbank: make ahci_highbank_pm_ops staticJingoo Han1-1/+1
Make ahci_highbank_pm_ops static because ahci_highbank_pm_ops is not exported. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-03Drivers: ata: remove __dev* attributes.Greg Kroah-Hartman1-1/+1
CONFIG_HOTPLUG is going away as an option. As a result, the __dev* markings need to be removed. This change removes the use of __devinit, __devexit_p, __devinitdata, and __devexit from these drivers. Based on patches originally written by Bill Pemberton, but redone by me in order to handle some of the coding style issues better, by hand. Cc: Bill Pemberton <wfp5p@virginia.edu> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-03sata_highbank: utilize common ata_platform_remove_one()Brian Norris1-11/+1
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-11-28sata_highbank: use ATA_BUSYSergei Shtylyov1-1/+1
ahci_highbank_hardreset() uses bare number for the BSY bit of the ATA status register, despite it is #define'd in <linux/ata.h> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-11-16[libata] PM callbacks should be conditionally compiled on CONFIG_PM_SLEEPYuanhan Liu1-1/+1
This will fix warnings like following when CONFIG_PM_SLEEP is not set: warning: 'xxx_suspend' defined but not used [-Wunused-function] warning: 'xxx_resume' defined but not used [-Wunused-function] Because SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn) Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM). Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: linux-ide@vger.kernel.org Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-11-15sata_highbank: mark ahci_highbank_probe as __devinitArnd Bergmann1-1/+1
The ahci_highbank_probe function is incorrectly marked as __init, which means it can get discarded at boot time, which might be a problem if for some reason the device only becomes operational after loading another module. Using __devinit instead avoids seeing this warning for every build: WARNING: vmlinux.o(.data+0xf7b0): Section mismatch in reference from the variable ahci_highbank_driver to the function .init.text:ahci_highbank_probe() The variable ahci_highbank_driver references the function __init ahci_highbank_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Mark Langsdorf <mark.langsdorf@calxeda.com> Cc: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-09-13ata: add platform driver for Calxeda AHCI controllerMark Langsdorf1-0/+450
Calxeda highbank SATA phy has intermittent problems bringing up a link with Gen3 drives. Retrying the phy hard reset can work-around this issue, but each reset also disables spread spectrum support. The reset function also needs to reprogram the phy to enable spread spectrum support. Create a new driver based on ahci_platform to support the Calxeda Highbank SATA controller. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>