| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
[ 2664.897267] sr 9:0:0:0: [sr0] Send:
[ 2664.897274] 0xf63d85e0
[ 2664.897283] sr 9:0:0:0: [sr0] CDB:
[ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
[ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
[ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
[ 2664.897338] ata_scsi_translate: ENTER
[ 2664.897345] ata_sg_setup: ENTER, ata1
[ 2664.897356] ata_sg_setup: 3 sg elements mapped
[ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
[ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
------------------------------------------------------> =======
[ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
[ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
[ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
[ 2664.897428] ata_sff_tf_load: device 0xA0
[ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
[ 2664.897457] ata_scsi_translate: EXIT
[ 2664.897462] leaving scsi_dispatch_cmnd()
[ 2664.897497] Doing sr request, dev = sr0, block = 0
[ 2664.897507] sr0 : reading 64/256 512 byte blocks.
[ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
[ 2664.897560] atapi_send_cdb: send cdb
[ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
[ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
[ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
[ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
[ 2666.910129] sr 9:0:0:0: [sr0] Done:
[ 2666.910136] 0xf63d85e0 TIMEOUT
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Factor out common code from serverworks_[re]init_one() to
serverworks_fixup().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Merge identical cable routines for Dell and Sun systems into
common oem_cable() one.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts. SFF ones no longer try to initialize
BMDMA or set PCI master.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When BMDMA initialization failed or BMDMA was not available for
whatever reason, bmdma_addr was left at zero and used as an indication
that BMDMA shouldn't be used. This leads to the following problems.
p1. For BMDMA drivers which don't use traditional BMDMA register,
ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those
drivers either have to inherit from ata_sff_port_ops or clear
->mode_filter explicitly.
p2. non-BMDMA drivers call into BMDMA PRD table allocation. It
doesn't actually allocate PRD table if bmdma_addr is not
initialized but is still confusing.
p3. For BMDMA drivers which don't use traditional BMDMA register, some
methods might not be invoked as expected (e.g. bmdma_stop from
ata_sff_post_internal_cmd()).
p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops
worrying libata core might call into one of them.
These problems are caused by the muddy line between SFF and BMDMA and
the assumption that all BMDMA controllers initialize bmdma_addr.
This patch fixes p1 and p2 by removing the bmdma_addr assumption and
moving prd allocation to BMDMA port start. Later patches will fix the
remaining issues.
This patch improves BMDMA initialization such that
* When BMDMA register initialization fails, falls back to PIO instead
of failing. ata_pci_bmdma_init() never fails now.
* When ata_pci_bmdma_init() falls back to PIO, it clears
ap->mwdma_mask and udma_mask instead of depending on
ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter()
unnecessary thus resolving p1.
* ata_port_start() which actually is BMDMA specific is moved to
ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start()
are killed.
* ata_sff_port_start32() is moved and renamed to
ata_bmdma_port_start32().
Drivers which no longer call into PRD table allocation are...
pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all
drivers which inherit from ata_sff_port_ops.
pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD
but is a BMDMA controller and doesn't have custom port_start like
other such controllers.
Note that with the previous patch which makes all and only BMDMA
drivers inherit from ata_bmdma_port_ops, this change doesn't break
drivers which need PRD table.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
No functional changes in this patch.
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.
This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.
This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.
Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
|
|
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.
Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.
As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
PCI device should be powered up or powered up before its PCI regsiters
are accessed. Although PCI configuration register access is allowed
in D3hot, PCI device is free to reset its status when transiting from
D3hot to D0 causing configuration data to change.
Many libata SFF drivers which use ata_pci_init_one() read and update
configuration registers before calling ata_pci_init_one() which
enables the PCI device. Also, in resume paths, some drivers access
registers without resuming the PCI device.
This patch adds a call to pcim_enable_device() in init path if
register is accessed before calling ata_pci_init_one() and make resume
paths first resume PCI devices, access PCI configuration regiters then
resume ATA host.
While at it...
* cmd640 was strange in that it set ->resume even when CONFIG_PM is
not. This is by-product of minimal build fix. Updated.
* In cs5530, Don't BUG() on reinit failure. Just whine and fail
resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
When masking, mask out the modes that are unsupported not the ones
that are supported. This makes life happier.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Minor tidying up. Only real change is to return UNK not 80 wire when we
don't know the cable type. This didn't use to matter but with Tejun's
reworking of cable detection it may.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The driver used the channel not the device number for deciding where to
load some timing parameters. Also change so that we clear the UDMA field
as the old driver did. Not believed neccessary but does no harm.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump the versions for drivers that were modified, but had not already
had a version number bump.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.
Note that pata_it8213 mask differed from the comment. Added a FIXME there.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH. Remove.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: Alan Cox <alan@redhat.com>
With some hand massaging from
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007.
I merely combined them all into a single patch.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bump versions based on changes submitted during 2.6.21 merge window.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch is against each libata driver.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.
As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
There were several places where ATA ID strings are manually terminated
and in some places possibly unterminated strings were passed to string
functions which don't limit length like strstr(). This patch converts
all of them over to ata_id_c_string().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency
with other ATA_ID_* constants.
* Kill ATA_SERNO_LEN
* Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN.
This change also makes ata_device_blacklisted() use proper length
for fwrev.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Most of these contributed by that mysterious figger known as A.C.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
The Serverworks chips need various fixups doing on a resume from RAM.
Conveniently the needed functions were already split out ready for re-use
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Many LLDs are missing sht->slave_destroy. The method is mandatory to
support device warm unplugging (echo 1 > /sys/.../delete). Without
it, libata might access released scsi device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
