summaryrefslogtreecommitdiffstats
path: root/drivers/Kconfig
AgeCommit message (Collapse)AuthorFilesLines
2018-06-28gnss: add GNSS receiver subsystemJohan Hovold1-0/+2
Add a new subsystem for GNSS (e.g. GPS) receivers. While GNSS receivers are typically accessed using a UART interface they often also support other I/O interfaces such as I2C, SPI and USB, while yet other devices use iomem or even some form of remote-processor messaging (rpmsg). The new GNSS subsystem abstracts the underlying interface and provides a new "gnss" class type, which exposes a character-device interface (e.g. /dev/gnss0) to user space. This allows GNSS receivers to have a representation in the Linux device model, something which is important not least for power management purposes. Note that the character-device interface provides raw access to whatever protocol the receiver is (currently) using, such as NMEA 0183, UBX or SiRF Binary. These protocols are expected to be continued to be handled by user space for the time being, even if some hybrid solutions are also conceivable (e.g. to have kernel drivers issue management commands). This will still allow for better platform integration by allowing GNSS devices and their resources (e.g. regulators and enable-gpios) to be described by firmware and managed by kernel drivers rather than platform-specific scripts and services. While the current interface is kept minimal, it could be extended using IOCTLs, sysfs or uevents as needs and proper abstraction levels are identified and determined (e.g. for device and feature identification). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-29hwtracing: Add HW tracing support menuRandy Dunlap1-3/+1
Make a "HW tracing support" menu and move 2 entries into it. (No change in Coresight, which is ARM-specific and is only listed for ARM & ARM64.) This makes the Device Drivers menu more consistent and prevents these drivers from being listed at the top level of the Device Drivers menu. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
2018-02-01Merge tag 'char-misc-4.16-rc1' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big pull request for char/misc drivers for 4.16-rc1. There's a lot of stuff in here. Three new driver subsystems were added for various types of hardware busses: - siox - slimbus - soundwire as well as a new vboxguest subsystem for the VirtualBox hypervisor drivers. There's also big updates from the FPGA subsystem, lots of Android binder fixes, the usual handful of hyper-v updates, and lots of other smaller driver updates. All of these have been in linux-next for a long time, with no reported issues" * tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits) char: lp: use true or false for boolean values android: binder: use VM_ALLOC to get vm area android: binder: Use true and false for boolean values lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN EISA: Delete error message for a failed memory allocation in eisa_probe() EISA: Whitespace cleanup misc: remove AVR32 dependencies virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES soundwire: Fix a signedness bug uio_hv_generic: fix new type mismatch warnings uio_hv_generic: fix type mismatch warnings auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE uio_hv_generic: add rescind support uio_hv_generic: check that host supports monitor page uio_hv_generic: create send and receive buffers uio: document uio_hv_generic regions doc: fix documentation about uio_hv_generic vmbus: add monitor_id and subchannel_id to sysfs per channel vmbus: fix ABI documentation uio_hv_generic: use ISR callback method ...
2017-12-19soundwire: Add SoundWire bus typeVinod Koul1-0/+2
This adds the base SoundWire bus type, bus and driver registration. along with changes to module device table for new SoundWire device type. Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-19slimbus: Add SLIMbus bus typeSagar Dharia1-0/+2
SLIMbus (Serial Low Power Interchip Media Bus) is a specification developed by MIPI (Mobile Industry Processor Interface) alliance. SLIMbus is a 2-wire implementation, which is used to communicate with peripheral components like audio-codec. SLIMbus uses Time-Division-Multiplexing to accommodate multiple data channels, and control channel. Control channel has messages to do device-enumeration, messages to send/receive control-data to/from SLIMbus devices, messages for port/channel management, and messages to do bandwidth allocation. The framework supports multiple instances of the bus (1 controller per bus), and multiple slave devices per controller. This patch adds support to basic silmbus core which includes support to SLIMbus type, slimbus device registeration and some basic data structures. Signed-off-by: Sagar Dharia <sdharia@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviwed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-19siox: new driver framework for eckelmann SIOXUwe Kleine-König1-0/+2
SIOX is a bus system invented at Eckelmann AG to control their building management and refrigeration systems. Traditionally the bus was implemented on custom microcontrollers, today Linux based machines are in use, too. The topology on a SIOX bus looks as follows: ,------->--DCLK-->---------------+----------------------. ^ v v ,--------. ,----------------------. ,------ | | | ,--------------. | | | |--->--DOUT-->---|->-|shift register|->-|--->---| | | | `--------------' | | | master | | device | | device | | | ,--------------. | | | |---<--DIN---<---|-<-|shift register|-<-|---<---| | | | `--------------' | | `--------' `----------------------' `------ v ^ ^ `----------DLD-------------------+----------------------' There are two control lines (DCLK and DLD) driven from the bus master to all devices in parallel and two daisy chained data lines, one for input and one for output. DCLK is the clock to shift both chains by a single bit. On an edge of DLD the devices latch both their input and output shift registers. This patch adds a framework for this bus type. Acked-by: Gavin Schenk <g.schenk@eckelmann.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-08drivers: visorbus: move driver out of stagingDavid Kershner1-0/+2
Move the visorbus driver out of staging (drivers/staging/unisys/visorbus) and to drivers/visorbus. Modify the configuration and makefiles so they now reference the new location. The s-Par header file visorbus.h that is referenced by all s-Par drivers, is being moved into include/linux. Signed-off-by: David Kershner <david.kershner@unisys.com> Reviewed-by: Tim Sell <timothy.sell@unisys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-13Merge branches 'pm-cpufreq-sched' and 'pm-opp'Rafael J. Wysocki1-0/+2
* pm-cpufreq-sched: cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq * pm-opp: PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper() PM / OPP: Support updating performance state of device's power domain PM / OPP: add missing of_node_put() for of_get_cpu_node() PM / OPP: Rename dev_pm_opp_register_put_opp_helper() PM / OPP: Add missing of_node_put(np) PM / OPP: Move error message to debug level PM / OPP: Use snprintf() to avoid kasprintf() and kfree() PM / OPP: Move the OPP directory out of power/
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03PM / OPP: Move the OPP directory out of power/Viresh Kumar1-0/+2
The drivers/base/power/ directory is special and contains code related to power management core like system suspend/resume, hibernation, etc. It was fine to keep the OPP code inside it when we had just one file for it, but it is growing now and already has a directory for itself. Lets move it directly under drivers/ directory, just like cpufreq and cpuidle. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-03mux: minimal mux subsystemPeter Rosin1-0/+2
Add a new minimalistic subsystem that handles multiplexer controllers. When multiplexers are used in various places in the kernel, and the same multiplexer controller can be used for several independent things, there should be one place to implement support for said multiplexer controller. A single multiplexer controller can also be used to control several parallel multiplexers, that are in turn used by different subsystems in the kernel, leading to a need to coordinate multiplexer accesses. The multiplexer subsystem handles this coordination. Thanks go out to Lars-Peter Clausen, Jonathan Cameron, Rob Herring, Wolfram Sang, Paul Gortmaker, Dan Carpenter, Colin Ian King, Greg Kroah-Hartman and last but certainly not least to Philipp Zabel for helpful comments, reviews, patches and general encouragement! Reviewed-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Peter Rosin <peda@axentia.se> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-09tee: generic TEE subsystemJens Wiklander1-0/+2
Initial patch for generic TEE subsystem. This subsystem provides: * Registration/un-registration of TEE drivers. * Shared memory between normal world and secure world. * Ioctl interface for interaction with user space. * Sysfs implementation_id of TEE driver A TEE (Trusted Execution Environment) driver is a driver that interfaces with a trusted OS running in some secure environment, for example, TrustZone on ARM cpus, or a separate secure co-processor etc. The TEE subsystem can serve a TEE driver for a Global Platform compliant TEE, but it's not limited to only Global Platform TEEs. This patch builds on other similar implementations trying to solve the same problem: * "optee_linuxdriver" by among others Jean-michel DELORME<jean-michel.delorme@st.com> and Emmanuel MICHEL <emmanuel.michel@st.com> * "Generic TrustZone Driver" by Javier González <javier@javigon.com> Acked-by: Andreas Dannenberg <dannenberg@ti.com> Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (HiKey) Tested-by: Volodymyr Babchuk <vlad.babchuk@gmail.com> (RCAR H3) Tested-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Javier González <javier@javigon.com> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2017-02-10drivers/fsi: Add empty fsi bus definitionsJeremy Kerr1-0/+2
This change adds the initial (empty) fsi bus definition, and introduces drivers/fsi/. Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Chris Bostic <cbostic@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-05-23Merge tag 'libnvdimm-for-4.7' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm updates from Dan Williams: "The bulk of this update was stabilized before the merge window and appeared in -next. The "device dax" implementation was revised this week in response to review feedback, and to address failures detected by the recently expanded ndctl unit test suite. Not included in this pull request are two dax topic branches (dax error handling, and dax radix-tree locking). These topics were deferred to get a few more days of -next integration testing, and to coordinate a branch baseline with Ted and the ext4 tree. Vishal and Ross will send the error handling and locking topics respectively in the next few days. This branch has received a positive build result from the kbuild robot across 226 configs. Summary: - Device DAX for persistent memory: Device DAX is the device-centric analogue of Filesystem DAX (CONFIG_FS_DAX). It allows memory ranges to be allocated and mapped without need of an intervening file system. Device DAX is strict, precise and predictable. Specifically this interface: a) Guarantees fault granularity with respect to a given page size (pte, pmd, or pud) set at configuration time. b) Enforces deterministic behavior by being strict about what fault scenarios are supported. Persistent memory is the first target, but the mechanism is also targeted for exclusive allocations of performance/feature differentiated memory ranges. - Support for the HPE DSM (device specific method) command formats. This enables management of these first generation devices until a unified DSM specification materializes. - Further ACPI 6.1 compliance with support for the common dimm identifier format. - Various fixes and cleanups across the subsystem" * tag 'libnvdimm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (40 commits) libnvdimm, dax: fix deletion libnvdimm, dax: fix alignment validation libnvdimm, dax: autodetect support libnvdimm: release ida resources Revert "block: enable dax for raw block devices" /dev/dax, core: file operations and dax-mmap /dev/dax, pmem: direct access to persistent memory libnvdimm: stop requiring a driver ->remove() method libnvdimm, dax: record the specified alignment of a dax-device instance libnvdimm, dax: reserve space to store labels for device-dax libnvdimm, dax: introduce device-dax infrastructure nfit: add sysfs dimm 'family' and 'dsm_mask' attributes tools/testing/nvdimm: ND_CMD_CALL support nfit: disable vendor specific commands nfit: export subsystem ids as attributes nfit: fix format interface code byte order per ACPI6.1 nfit, libnvdimm: limited/whitelisted dimm command marshaling mechanism nfit, libnvdimm: clarify "commands" vs "_DSMs" libnvdimm: increase max envelope size for ioctl acpi/nfit: Add sysfs "id" for NVDIMM ID ...
2016-05-20/dev/dax, pmem: direct access to persistent memoryDan Williams1-0/+2
Device DAX is the device-centric analogue of Filesystem DAX (CONFIG_FS_DAX). It allows memory ranges to be allocated and mapped without need of an intervening file system. Device DAX is strict, precise and predictable. Specifically this interface: 1/ Guarantees fault granularity with respect to a given page size (pte, pmd, or pud) set at configuration time. 2/ Enforces deterministic behavior by being strict about what fault scenarios are supported. For example, by forcing MADV_DONTFORK semantics and omitting MAP_PRIVATE support device-dax guarantees that a mapping always behaves/performs the same once established. It is the "what you see is what you get" access mechanism to differentiated memory vs filesystem DAX which has filesystem specific implementation semantics. Persistent memory is the first target, but the mechanism is also targeted for exclusive allocations of performance differentiated memory ranges. This commit is limited to the base device driver infrastructure to associate a dax device with pmem range. Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2016-04-29dma-buf/sync_file: de-stage sync_fileGustavo Padovan1-0/+2
sync_file is useful to connect one or more fences to the file. The file is used by userspace to track fences between drivers that share DMA bufs. Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-04Merge tag 'char-misc-4.4-rc1' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big char/misc driver update for 4.4-rc1. Lots of different driver and subsystem updates, hwtracing being the largest with the addition of some new platforms that are now supported. Full details in the shortlog. All of these have been in linux-next for a long time with no reported issues" * tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits) fpga: socfpga: Fix check of return value of devm_request_irq lkdtm: fix ACCESS_USERSPACE test mcb: Destroy IDA on module unload mcb: Do not return zero on error path in mcb_pci_probe() mei: bus: set the device name before running fixup mei: bus: use correct lock ordering mei: Fix debugfs filename in error output char: ipmi: ipmi_ssif: Replace timeval with timespec64 fpga: zynq-fpga: Fix issue with drvdata being overwritten. fpga manager: remove unnecessary null pointer checks fpga manager: ensure lifetime with of_fpga_mgr_get fpga: zynq-fpga: Change fw format to handle bin instead of bit. fpga: zynq-fpga: Fix unbalanced clock handling misc: sram: partition base address belongs to __iomem space coresight: etm3x: adding documentation for sysFS's cpu interface vme: 8-bit status/id takes 256 values, not 255 fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000 ARM: zynq: dt: Updated devicetree for Zynq 7000 platform. ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager. ver_linux: proc/modules, limit text processing to 'sed' ...
2015-10-29lightnvm: Support for Open-Channel SSDsMatias Bjørling1-0/+2
Open-channel SSDs are devices that share responsibilities with the host in order to implement and maintain features that typical SSDs keep strictly in firmware. These include (i) the Flash Translation Layer (FTL), (ii) bad block management, and (iii) hardware units such as the flash controller, the interface controller, and large amounts of flash chips. In this way, Open-channels SSDs exposes direct access to their physical flash storage, while keeping a subset of the internal features of SSDs. LightNVM is a specification that gives support to Open-channel SSDs LightNVM allows the host to manage data placement, garbage collection, and parallelism. Device specific responsibilities such as bad block management, FTL extensions to support atomic IOs, or metadata persistence are still handled by the device. The implementation of LightNVM consists of two parts: core and (multiple) targets. The core implements functionality shared across targets. This is initialization, teardown and statistics. The targets implement the interface that exposes physical flash to user-space applications. Examples of such targets include key-value store, object-store, as well as traditional block devices, which can be application-specific. Contributions in this patch from: Javier Gonzalez <jg@lightnvm.io> Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Jesper Madsen <jmad@itu.dk> Signed-off-by: Matias Bjørling <m@bjorling.me> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-10-09nvme: move to a new drivers/nvme/host directoryJay Sternberg1-0/+2
This patch moves the NVMe driver from drivers/block/ to its own new drivers/nvme/host/ directory. This is in preparation of splitting the current monolithic driver up and add support for the upcoming NVMe over Fabrics standard. The drivers/nvme/host/ is chose to leave space for a NVMe target implementation in addition to this host side driver. Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> [hch: rebased, renamed core.c to pci.c, slight tweaks] Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2015-10-07add FPGA manager coreAlan Tull1-0/+2
API to support programming FPGA's. The following functions are exported as GPL: * fpga_mgr_buf_load Load fpga from image in buffer * fpga_mgr_firmware_load Request firmware and load it to the FPGA. * fpga_mgr_register * fpga_mgr_unregister FPGA device drivers can be added by calling fpga_mgr_register() to register a set of fpga_manager_ops to do device specific stuff. * of_fpga_mgr_get * fpga_mgr_put Get/put a reference to a fpga manager. The following sysfs files are created: * /sys/class/fpga_manager/<fpga>/name Name of low level driver. * /sys/class/fpga_manager/<fpga>/state State of fpga manager Signed-off-by: Alan Tull <atull@opensource.altera.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04intel_th: Add driver infrastructure for Intel(R) Trace Hub devicesAlexander Shishkin1-0/+2
Intel(R) Trace Hub (TH) is a set of hardware blocks (subdevices) that produce, switch and output trace data from multiple hardware and software sources over several types of trace output ports encoded in System Trace Protocol (MIPI STPv2) and is intended to perform full system debugging. For these subdevices, we create a bus, where they can be discovered and configured by userspace software. This patch creates this bus infrastructure, three types of devices (source, output, switch), resource allocation, some callback mechanisms to facilitate communication between the subdevices' drivers and some common sysfs attributes. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04stm class: Introduce an abstraction for System Trace Module devicesAlexander Shishkin1-0/+2
A System Trace Module (STM) is a device exporting data in System Trace Protocol (STP) format as defined by MIPI STP standards. Examples of such devices are Intel(R) Trace Hub and Coresight STM. This abstraction provides a unified interface for software trace sources to send their data over an STM device to a debug host. In order to do that, such a trace source needs to be assigned a pair of master/channel identifiers that all the data from this source will be tagged with. The STP decoder on the debug host side will use these master/channel tags to distinguish different trace streams from one another inside one STP stream. This abstraction provides a configfs-based policy management mechanism for dynamic allocation of these master/channel pairs based on trace source-supplied string identifier. It has the flexibility of being defined at runtime and at the same time (provided that the policy definition is aligned with the decoding end) consistency. For userspace trace sources, this abstraction provides write()-based and mmap()-based (if the underlying stm device allows this) output mechanism. For kernel-side trace sources, we provide "stm_source" device class that can be connected to an stm device at run time. Cc: linux-api@vger.kernel.org Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-03Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds1-0/+2
Pull ARM development updates from Russell King: "Included in this update: - moving PSCI code from ARM64/ARM to drivers/ - removal of some architecture internals from global kernel view - addition of software based "privileged no access" support using the old domains register to turn off the ability for kernel loads/stores to access userspace. Only the proper accessors will be usable. - addition of early fixup support for early console - re-addition (and reimplementation) of OMAP special interconnect barrier - removal of finish_arch_switch() - only expose cpuX/online in sysfs if hotpluggable - a number of code cleanups" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits) ARM: software-based priviledged-no-access support ARM: entry: provide uaccess assembly macro hooks ARM: entry: get rid of multiple macro definitions ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die() ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore() ARM: mm: improve do_ldrd_abort macro ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit() ARM: entry: efficiency cleanups ARM: entry: get rid of asm_trace_hardirqs_on_cond ARM: uaccess: simplify user access assembly ARM: domains: remove DOMAIN_TABLE ARM: domains: keep vectors in separate domain ARM: domains: get rid of manager mode for user domain ARM: domains: move initial domain setting value to asm/domains.h ARM: domains: provide domain_mask() ARM: domains: switch to keeping domain value in register ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD() ARM: 8416/1: Feroceon: use of_iomap() to map register base ARM: 8415/1: early fixmap support for earlycon ...
2015-08-05nvmem: Add a simple NVMEM framework for nvmem providersSrinivas Kandagatla1-0/+2
This patch adds just providers part of the framework just to enable easy review. Up until now, NVMEM drivers like eeprom were stored in drivers/misc, where they all had to duplicate pretty much the same code to register a sysfs file, allow in-kernel users to access the content of the devices they were driving, etc. This was also a problem as far as other in-kernel users were involved, since the solutions used were pretty much different from on driver to another, there was a rather big abstraction leak. This introduction of this framework aims at solving this. It also introduces DT representation for consumer devices to go get the data they require (MAC Addresses, SoC/Revision ID, part numbers, and so on) from the nvmems. Having regmap interface to this framework would give much better abstraction for nvmems on different buses. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> [Maxime Ripard: intial version of eeprom framework] Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-31arm: perf: factor arm_pmu core out to driversMark Rutland1-0/+2
To enable sharing of the arm_pmu code with arm64, this patch factors it out to drivers/perf/. A new drivers/perf directory is added for performance monitor drivers to live under. MAINTAINERS is updated accordingly. Files added previously without a corresponsing MAINTAINERS update (perf_regs.c, perf_callchain.c, and perf_event.h) are also added. Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Russell King <linux@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> [will: augmented Kconfig help slightly] Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-06-24libnvdimm, nfit: initial libnvdimm infrastructure and NFIT supportDan Williams1-0/+2
A struct nvdimm_bus is the anchor device for registering nvdimm resources and interfaces, for example, a character control device, nvdimm devices, and I/O region devices. The ACPI NFIT (NVDIMM Firmware Interface Table) is one possible platform description for such non-volatile memory resources in a system. The nfit.ko driver attaches to the "ACPI0012" device that indicates the presence of the NFIT and parses the table to register a struct nvdimm_bus instance. Cc: <linux-acpi@vger.kernel.org> Cc: Lv Zheng <lv.zheng@intel.com> Cc: Robert Moore <robert.moore@intel.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Christoph Hellwig <hch@lst.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2015-02-03i2o: move to stagingAlan Cox1-2/+0
The I2O layer deals with a technology that to say the least didn't catch on in the market. The only relevant products are some of the AMI MegaRAID - which supported I2O and its native mode (The native mode is faster and runs on Linux), an obscure crypto ethernet card that's now so many years out of date nobody would use it, the old DPT controllers, which speak their own dialect and have their own driver - and ermm.. thats about it. We also know the code isn't in good shape as recently a patch was proposed and queried as buggy, which in turn showed the existing code was broken already by prior "clean up" and nobody had noticed that either. It's coding style robot code nothing more. Like some forgotten corridor cleaned relentlessly by a lost Roomba but where no user has trodden in years. Move it to staging and then to /dev/null. The headers remain as they are shared with dpt_i2o. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-25drivers/Kconfig: remove duplicate entry for socLars Poeschel1-2/+0
For some reason there was the same menu entry in menuconfig twice. This trivial patch leaves the one that is older as is and removes the other entry. Signed-off-by: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-15Merge tag 'staging-3.19-rc1' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver updates from Greg KH: "Here's the big staging tree pull request for 3.19-rc1. We continued to delete more lines than were added, always a good thing, but not at a huge rate this release, only about 70k lines removed overall mostly from removing the horrid bcm driver. Lots of normal staging driver cleanups and fixes all over the place, well over a thousand of them, the shortlog shows all the horrid details. The "contentious" thing here is the movement of the Android binder code out of staging into the "real" part of the kernel. This is code that has been stable for a few years now and is working as-is in the tens of millions of devices with no issues. Yes, the code is horrid, and the userspace api leaves a lot to be desired, but it's not going to change due to legacy issues that we have no control over. Because so many devices and companies rely on this, and the code is stable, might as well promote it out of staging. This was all discussed at the Linux Plumbers conference, and everyone participating agreed that this was the best way forward. There is work happening to replace the binder code with something new that is happening right now, but I don't expect to see the results of that work for another year at the earliest. If that ever happens, and Android switches over to it, I'll gladly remove this version. As for maintainers, I'll be glad to maintain this code, I've been doing it for the past few years with no problems. I'll send a MAINTAINERS entry for it before 3.19-final is out, still need to talk to the Google developers about if they are willing to help with it or not, last I checked they were, which was good. All of these patches have been in linux-next for a while with no reported issues" * tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits) Staging: slicoss: Fix long line issues in slicoss.c staging: rtl8712: remove unnecessary else after return staging: comedi: change some printk calls to pr_err staging: rtl8723au: hal: Removed the extra semicolon lustre: Deletion of unnecessary checks before three function calls staging: lustre: fix sparse warnings: static function declaration staging: lustre: fixed sparse warnings related to static declarations staging: unisys: remove duplicate header staging: unisys: remove unneeded structure staging: ft1000 : replace __attribute ((__packed__) with __packed drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c" Drivers:staging:rtl8192e: Fixed checkpatch warning Drivers:staging:clocking-wizard: Added a newline staging: clocking-wizard: check for a valid clk_name pointer staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1() staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB() staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation ...
2014-11-26ARM: tegra: Move AHB Kconfig to drivers/ambaThierry Reding1-0/+2
This will allow the Kconfig option to be shared among 32-bit and 64-bit ARM. Signed-off-by: Thierry Reding <treding@nvidia.com>
2014-10-20staging: android: binder: move to the "real" part of the kernelGreg Kroah-Hartman1-0/+2
The Android binder code has been "stable" for many years now. No matter what comes in the future, we are going to have to support this API, so might as well move it to the "real" part of the kernel as there's no real work that needs to be done to the existing code. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-24soc: ti: add Keystone Navigator QMSS driverSandeep Nair1-0/+2
The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of the main hardware sub system which forms the backbone of the Keystone Multi-core Navigator. QMSS consist of queue managers, packed-data structure processors(PDSP), linking RAM, descriptor pools and infrastructure Packet DMA. The Queue Manager is a hardware module that is responsible for accelerating management of the packet queues. Packets are queued/de-queued by writing or reading descriptor address to a particular memory mapped location. The PDSPs perform QMSS related functions like accumulation, QoS, or event management. Linking RAM registers are used to link the descriptors which are stored in descriptor RAM. Descriptor RAM is configurable as internal or external memory. The QMSS driver manages the PDSP setups, linking RAM regions, queue pool management (allocation, push, pop and notify) and descriptor pool management. The specifics on the device tree bindings for QMSS can be found in: Documentation/devicetree/bindings/soc/keystone-navigator-qmss.txt Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Kumar Gala <galak@codeaurora.org> Cc: Olof Johansson <olof@lixom.net> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Sandeep Nair <sandeep_n@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
2014-08-04Merge tag 'char-misc-3.17-rc1' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char / misc driver patches from Greg KH: "Here's the big driver misc / char pull request for 3.17-rc1. Lots of things in here, the thunderbolt support for Apple laptops, some other new drivers, testing fixes, and other good things. All have been in linux-next for a long time" * tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits) misc: bh1780: Introduce the use of devm_kzalloc Lattice ECP3 FPGA: Correct endianness drivers/misc/ti-st: Load firmware from ti-connectivity directory. dt-bindings: extcon: Add support for SM5502 MUIC device extcon: sm5502: Change internal hardware switch according to cable type extcon: sm5502: Detect cable state after completing platform booting extcon: sm5502: Add support new SM5502 extcon device driver extcon: arizona: Get MICVDD against extcon device extcon: Remove unnecessary OOM messages misc: vexpress: Fix sparse non static symbol warnings mei: drop unused hw dependent fw status functions misc: bh1770glc: Use managed functions pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage misc: remove DEFINE_PCI_DEVICE_TABLE usage ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use drivers/char/dsp56k.c: drop check for negativity of unsigned parameter mei: fix return value on disconnect timeout mei: don't schedule suspend in pm idle mei: start disconnect request timer consistently mei: reset client connection state on timeout ...
2014-06-23trace, RAS: Add basic RAS trace eventChen, Gong1-0/+2
To avoid confuision and conflict of usage for RAS related trace event, add an unified RAS trace event stub. Start a RAS subsystem menu which will be fleshed out in time, when more features get added to it. Signed-off-by: Chen, Gong <gong.chen@linux.intel.com> Link: http://lkml.kernel.org/r/1402475691-30045-2-git-send-email-gong.chen@linux.intel.com Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
2014-06-19thunderbolt: Add initial cactus ridge NHI supportAndreas Noever1-0/+2
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple decided to implement thunderbolt at the operating system level. The firmare only initializes thunderbolt devices that are present at boot time. This driver enables hotplug of thunderbolt of non-chained thunderbolt devices on Apple systems with a cactus ridge controller. This first patch adds the Kconfig file as well the parts of the driver which talk directly to the hardware (that is pci device setup, interrupt handling and RX/TX ring management). Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-23soc: Introduce drivers/soc place-holder for SOC specific driversSantosh Shilimkar1-0/+2
Based on earlier thread "https://lkml.org/lkml/2013/10/7/662" and discussion at Kernel Summit'2013, it was agreed to create 'driver/soc' for drivers which are quite SOC specific. Further discussion on the subject is in response to the earlier version of the patch is here: http://lwn.net/Articles/588942/ Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Kumar Gala <galak@codeaurora.org> Cc: Paul Walmsley <paul@pwsan.com> Cc: Olof Johansson <olof@lixom.net> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sandeep Nair <sandeep_n@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Kumar Gala <galak@codeaurora.org>
2014-02-28drivers: Introduce MEN Chameleon BusJohannes Thumshirn1-0/+2
The MCB (MEN Chameleon Bus) is a Bus specific to MEN Mikroelektronik FPGA based devices. It is used to identify MCB based IP-Cores within an FPGA and provide the necessary framework for instantiating drivers for these devices. Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-15spmi: Linux driver framework for SPMIKenneth Heitke1-0/+2
System Power Management Interface (SPMI) is a specification developed by the MIPI (Mobile Industry Process Interface) Alliance optimized for the real time control of Power Management ICs (PMIC). SPMI is a two-wire serial interface that supports up to 4 master devices and up to 16 logical slaves. The framework supports message APIs, multiple busses (1 controller per bus) and multiple clients/slave devices per controller. Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: Michael Bohan <mbohan@codeaurora.org> Signed-off-by: Josh Cartwright <joshc@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-11-14Merge tag 'pm+acpi-3.13-rc1' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management updates from Rafael J Wysocki: - New power capping framework and the the Intel Running Average Power Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan. - Addition of the in-kernel switching feature to the arm_big_little cpufreq driver from Viresh Kumar and Nicolas Pitre. - cpufreq support for iMac G5 from Aaro Koskinen. - Baytrail processors support for intel_pstate from Dirk Brandewie. - cpufreq support for Midway/ECX-2000 from Mark Langsdorf. - ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha. - ACPI power management support for the I2C and SPI bus types from Mika Westerberg and Lv Zheng. - cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat, Stratos Karafotis, Xiaoguang Chen, Lan Tianyu. - cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev. - intel_pstate updates from Dirk Brandewie and Adrian Huang. - ACPICA update to version 20130927 includig fixes and cleanups and some reduction of divergences between the ACPICA code in the kernel and ACPICA upstream in order to improve the automatic ACPICA patch generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh Bhat, Bjorn Helgaas, David E Box. - ACPI IPMI driver fixes and cleanups from Lv Zheng. - ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang Yanfei, Rafael J Wysocki. - Conversion of the ACPI AC driver to the platform bus type and multiple driver fixes and cleanups related to ACPI from Zhang Rui. - ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu, Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki. - Fixes and cleanups and new blacklist entries related to the ACPI video support from Aaron Lu, Felipe Contreras, Lennart Poettering, Kirill Tkhai. - cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi. - cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han, Bartlomiej Zolnierkiewicz, Prarit Bhargava. - devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe. - Operation Performance Points (OPP) core updates from Nishanth Menon. - Runtime power management core fix from Rafael J Wysocki and update from Ulf Hansson. - Hibernation fixes from Aaron Lu and Rafael J Wysocki. - Device suspend/resume lockup detection mechanism from Benoit Goby. - Removal of unused proc directories created for various ACPI drivers from Lan Tianyu. - ACPI LPSS driver fix and new device IDs for the ACPI platform scan handler from Heikki Krogerus and Jarkko Nikula. - New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa. - Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter, Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause, Liu Chuansheng. - Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding, Jean-Christophe Plagniol-Villard. * tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits) cpufreq: conservative: fix requested_freq reduction issue ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines PM / runtime: Use pm_runtime_put_sync() in __device_release_driver() ACPI / event: remove unneeded NULL pointer check Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1" ACPI / video: Quirk initial backlight level 0 ACPI / video: Fix initial level validity test intel_pstate: skip the driver if ACPI has power mgmt option PM / hibernate: Avoid overflow in hibernate_preallocate_memory() ACPI / hotplug: Do not execute "insert in progress" _OST ACPI / hotplug: Carry out PCI root eject directly ACPI / hotplug: Merge device hot-removal routines ACPI / hotplug: Make acpi_bus_hot_remove_device() internal ACPI / hotplug: Simplify device ejection routines ACPI / hotplug: Fix handle_root_bridge_removal() ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug ACPI / scan: Start matching drivers after trying scan handlers ACPI: Remove acpi_pci_slot_init() headers from internal.h ACPI / blacklist: fix name of ThinkPad Edge E530 PowerCap: Fix build error with option -Werror=format-security ... Conflicts: arch/arm/mach-omap2/opp.c drivers/Kconfig drivers/spi/spi.c
2013-10-17PowerCap: Add to drivers Kconfig and MakefileSrinivas Pandruvada1-0/+2
Added changes to Makefile and Kconfig to include in driver build. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-09-27drivers: phy: add generic PHY frameworkKishon Vijay Abraham I1-0/+2
The PHY framework provides a set of APIs for the PHY drivers to create/destroy a PHY and APIs for the PHY users to obtain a reference to the PHY with or without using phandle. For dt-boot, the PHY drivers should also register *PHY provider* with the framework. PHY drivers should create the PHY by passing id and ops like init, exit, power_on and power_off. This framework is also pm runtime enabled. The documentation for the generic PHY framework is added in Documentation/phy.txt and the documentation for dt binding can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt Cc: Tomasz Figa <t.figa@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-10Merge tag 'mfd-3.11-1' of ↵Linus Torvalds1-2/+0
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next Pull MFD update from Samuel Ortiz: "For the 3.11 merge we only have one new MFD driver for the Kontron PLD. But we also have: - Support for the TPS659038 PMIC from the palmas driver. - Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver. - RTL8411B support from the rtsx driver. - More DT support for the Arizona, max8998, twl4030-power and the ti_am335x_tsadc drivers. - The SSBI driver move under MFD. - A conversion to the devm_* API for most of the MFD drivers. - The twl4030-power got split from twl-core into its own module. - A major ti_am335x_adc cleanup, leading to a proper DT support. - Our regular arizona and wm* updates and cleanups from the Wolfson folks. - A better error handling and initialization, and a regulator subdevice addition for the 88pm80x driver. - A bulk platform_set_drvdata() call removal that's no longer need since commit 0998d0631001 ("device-core: Ensure drvdata = NULL when no driver is bound") * tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits) mfd: sec: Provide max_register to regmap mfd: wm8994: Remove duplicate check for active JACKDET MAINTAINERS: Add include directory to MFD file patterns mfd: sec: Remove fields not used since regmap conversion watchdog: Kontron PLD watchdog timer driver mfd: max8998: Add support for Device Tree regulator: max8998: Use arrays for specifying voltages in platform data mfd: max8998: Add irq domain support regulator: palmas: Add TPS659038 support mfd: Kontron PLD mfd driver mfd: palmas: Add TPS659038 PMIC support mfd: palmas: Add SMPS10_BOOST feature mfd: palmas: Check if irq is valid mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs mfd: twl-core: Change TWL6025 references to TWL6032 mfd: davinci_voicecodec: Fix build breakage mfd: vexpress: Make the driver optional for arm and arm64 mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache() mfd: davinci_voicecodec: Convert to use devm_* APIs mfd: twl4030-power: Fix relocking on error ...
2013-06-17FMC: create drivers/fmc and toplevel Kconfig questionAlessandro Rubini1-0/+2
This commit creates the drivers/fmc directory and puts the necessary hooks for kbuild and kconfig. The code is currently a placeholder that only registers an empty bus. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Acked-by: Juan David Gonzalez Cobas <dcobas@cern.ch> Acked-by: Emilio G. Cota <cota@braap.org> Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-11mfd: Move ssbi driver into drivers/mfdArnd Bergmann1-2/+0
There is no reason for ssbi to have its own top-level driver directory when the only users of this interface are all MFD drivers. The only mainline driver using it at the moment (PM8921) is marked broken and in fact does not compile. I have verified that fixing the trivial build breakage in pm8921 links in the new ssbi code just fine, but that can be a separate patch. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-05-04Merge tag 'drivers-for-linus' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver changes from Olof Johansson: "This is a rather large set of patches for device drivers that for one reason or another the subsystem maintainer preferred to get merged through the arm-soc tree. There are both new drivers as well as existing drivers that are getting converted from platform-specific code into standalone drivers using the appropriate subsystem specific interfaces. In particular, we can now have pinctrl, clk, clksource and irqchip drivers in one file per driver, without the need to call into platform specific interface, or to get called from platform specific code, as long as all information about the hardware is provided through a device tree. Most of the drivers we touch this time are for clocksource. Since now most of them are part of drivers/clocksource, I expect that we won't have to touch these again from arm-soc and can let the clocksource maintainers take care of these in the future. Another larger part of this series is specific to the exynos platform, which is seeing some significant effort in upstreaming and modernization of its device drivers this time around, which unfortunately is also the cause for the churn and a lot of the merge conflicts. There is one new subsystem that gets merged as part of this series: the reset controller interface, which is a very simple interface for taking devices on the SoC out of reset or back into reset. Patches to use this interface on i.MX follow later in this merge window, and we are going to have other platforms (at least tegra and sirf) get converted in 3.11. This will let us get rid of platform specific callbacks in a number of platform independent device drivers." * tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits) irqchip: s3c24xx: add missing __init annotations ARM: dts: Disable the RTC by default on exynos5 clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3} ARM: exynos: restore mach/regs-clock.h for exynos5 clocksource: exynos_mct: fix build error on non-DT pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register() irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure reset: NULL deref on allocation failure reset: Add reset controller API dt: describe base reset signal binding ARM: EXYNOS: Add arm-pmu DT binding for exynos421x ARM: EXYNOS: Add arm-pmu DT binding for exynos5250 ARM: EXYNOS: Enable PMUs for exynos4 irqchip: exynos-combiner: Correct combined IRQs for exynos4 irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq ARM: EXYNOS: fix compilation error introduced due to common clock migration clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3} clk: exynos4: export clocks required for fimc-is clk: samsung: Fix compilation error clk: tegra: fix enum tegra114_clk to match binding ...
2013-04-30kconfig menu: move Virtualization drivers near other virtualization optionsRandy Dunlap1-2/+2
Make virtualization drivers be logically grouped together (physically near each other) in the kconfig menu by moving "Virtualization drivers" to be near "Virtio drivers", Microsort Hyper-V, and Xen driver support. This is just a user-friendly, visual search change. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Alexander Graf <agraf@suse.de> Cc: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-04-12reset: Add reset controller APIPhilipp Zabel1-0/+2
This adds a simple API for devices to request being reset by separate reset controller hardware and implements the reset signal device tree binding. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz>
2013-03-25add single-wire serial bus interface (SSBI) driverKenneth Heitke1-0/+2
SSBI is the Qualcomm single-wire serial bus interface used to connect the MSM devices to the PMIC and other devices. Since SSBI only supports a single slave, the driver gets the name of the slave device passed in from the board file through the master device's platform data. SSBI registers pretty early (postcore), so that the PMIC can come up before the board init. This is useful if the board init requires the use of gpios that are connected through the PMIC. Based on a patch by Dima Zavin <dima@android.com> that can be found at: http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4 This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter is a hardware wrapper around the SSBI 2.0 controller that is designed to overcome concurrency issues and security limitations. A controller_type field is added to the platform data to specify the type of the SSBI controller (1.0, 2.0, or PMIC Arbiter). [davidb@codeaurora.org: I've moved this driver into drivers/ssbi/ and added an include for linux/module.h so that it will compile] Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-02-21Merge tag 'char-misc-3.9-rc1' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver patches from Greg Kroah-Hartman: "Here's the big char/misc driver patches for 3.9-rc1. Nothing major here, just lots of different driver updates (mei, hyperv, ipack, extcon, vmci, etc.). All of these have been in the linux-next tree for a while." * tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits) w1: w1_therm: Add force-pullup option for "broken" sensors w1: ds2482: Added 1-Wire pull-up support to the driver vme: add missing put_device() after device_register() fails extcon: max8997: Use workqueue to check cable state after completing boot of platform extcon: max8997: Set default UART/USB path on probe extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type extcon: max8997: Set default of ADC debounce time during initialization extcon: max8997: Remove duplicate code related to set H/W line path extcon: max8997: Move defined constant to header file extcon: max77693: Make max77693_extcon_cable static extcon: max8997: Remove unreachable code extcon: max8997: Make max8997_extcon_cable static extcon: max77693: Remove unnecessary goto statement to improve readability extcon: max77693: Convert to devm_input_allocate_device() extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style CREDITS: update email and address of Harald Hoyer extcon: arizona: Use MICDET for final microphone identification extcon: arizona: Always take the first HPDET reading as the final one extcon: arizona: Clear _trig_sts bits after jack detection extcon: arizona: Don't HPDET magic when headphones are enabled ...
2013-02-02ARM / highbank: add support for pl320 IPCRob Herring1-0/+2
The pl320 IPC allows for interprocessor communication between the highbank A9 and the EnergyCore Management Engine. The pl320 implements a straightforward mailbox protocol. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>