| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Third Round of Renesas ARM Based SoC Fixes for v5.0
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
* tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7743: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Booting 4.20 on a TheCUS N2100 results in a kernel oops while probing
PCI, due to n2100_pci_map_irq() having been discarded during boot.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: stable@vger.kernel.org # 2.6.18+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Device tree fixes for omaps for v5.0-rc cycle
This series of dts fixes for omap devices fixes several device specific
regressions:
- The onenand timings for n950/n9 have been wrong for a while since
we moved to dts based timings
- A typo for the cpcap pmic is now producing erors during boot as the
level should be 0 for unconfigurable triggering instead of 1
- Changes for ti-sysc for omap5 left uart3 with debug flags that should
not be set
- Fix a new dtc warning started showing up for omap3-gta04 grap_port
- With the generic MMC card detection code we need to fix the gpio
in dts for n900 and am335x-shc
* tag 'omap-for-v5.0/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: dts: Remove unnecessary idle flags for omap5 uart3
ARM: dts: omap4-droid4: Fix typo in cpcap IRQ flags
ARM: OMAP: dts: N950/N9: fix onenand timings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This fixes a long standing typo in device-tree for DA850 in interrupt
number for timer. It did not affect us so far because we use non-DT
timer driver within mach-davinci. This was caught while migrating to
clocksource driver.
* tag 'davinci-fixes-for-v5.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: fix interrupt numbers for clocksource
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/fixes
Qualcomm ARM64 Fixes for 5.0-rc3
* Fix irq controller compatible for the MSM8996 platforms
* tag 'qcom-fixes-for-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: add msm8996 compatible to gicv3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Second Round of Renesas ARM Based SoC Fixes for v5.0
Enable DMA for SCIF2 on R-Car M3-W (r8a7796) and M3-n (r8a77965), and
(RZ/G2M) r8a774a1 SoCs.
This is was omitted from patches enabling DMA for other SCIF devices on the
same SoCs due to missing documentation. However, it is regarded as a fix
as arguably those patches claim to add this feature.
Per-SoC patches are provided to ease backporting of this fix as the kernel
version to be fixed is different for each SoC.
* tag 'renesas-fixes2-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is the pxa fixes set for v4.20 cycle:
- only a single devm allocated pointer free fix, which was never
triggered runtime but code analysis found.
* tag 'pxa-fixes-5.0' of https://github.com/rjarzmik/linux:
ARM: pxa: ssp: unneeded to free devm_ allocated data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit ae0037dbfc5eaa3d2ec8bdae6e7923cdce886062.
Andy writes:
I'd prefer in this instance that this patch get dropped from
char-misc. I have too much stuff in flight with some additional
patches coming in to mess with this right now. And we don't
have clients rdy anyway for this so let's wait till next cycle
on this one.
Reported-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
show_ldttss() shifts desc.base2 by 24 bit, but base2 is 8 bits of a
bitfield in a u16.
Due to the really great idea of integer promotion in C99 base2 is promoted
to an int, because that's the standard defined behaviour when all values
which can be represented by base2 fit into an int.
Now if bit 7 is set in desc.base2 the result of the shift left by 24 makes
the resulting integer negative and the following conversion to unsigned
long legitmately sign extends first causing the upper bits 32 bits to be
set in the result.
Fix this by casting desc.base2 to unsigned long before the shift.
Detected by CoverityScan, CID#1475635 ("Unintended sign extension")
[ tglx: Reworded the changelog a bit as I actually had to lookup
the standard (again) to decode the original one. ]
Fixes: a1a371c468f7 ("x86/fault: Decode page fault OOPSes better")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20181222191116.21831-1-colin.king@canonical.com
|
|
to long mode
In some old AMD KVM implementation, guest's EFER.LME bit is cleared by KVM
when the hypervsior detects that the guest sets CR0.PG to 0. This causes
the guest OS to reboot when it tries to return from 32-bit trampoline code
because the CPU is in incorrect state: CR4.PAE=1, CR0.PG=1, CS.L=1, but
EFER.LME=0. As a precaution, set EFER.LME=1 as part of long mode
activation procedure. This extra step won't cause any harm when Linux is
booted on a bare-metal machine.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20190104054411.12489-1-wei@redhat.com
|
|
When generating vdso-o32.lds & vdso-n32.lds for use with programs
running as compat ABIs under 64b kernels, we previously haven't included
the compiler flags that are supposedly common to all ABIs - ie. those in
the ccflags-vdso variable.
This is problematic in cases where we need to provide the -m%-float flag
in order to ensure that we don't attempt to use a floating point ABI
that's incompatible with the target CPU & ABI. For example a toolchain
using current gcc trunk configured --with-fp-32=xx fails to build a
64r6el_defconfig kernel with the following error:
cc1: error: '-march=mips1' requires '-mfp32'
make[2]: *** [arch/mips/vdso/Makefile:135: arch/mips/vdso/vdso-o32.lds] Error 1
Include $(ccflags-vdso) for the compat VDSO .lds builds, just as it is
included for the native VDSO .lds & when compiling objects for the
compat VDSOs. This ensures we consistently provide the -msoft-float flag
amongst others, avoiding the problem by ensuring we're agnostic to the
toolchain defaults.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: linux-mips@vger.kernel.org
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Maciej W . Rozycki <macro@linux-mips.org>
Cc: stable@vger.kernel.org # v4.4+
|
|
The MIPS VDSO build currently doesn't provide the -msoft-float flag to
the compiler as the kernel proper does. This results in an attempt to
use the compiler's default floating point configuration, which can be
problematic in cases where this is incompatible with the target CPU's
-march= flag. For example decstation_defconfig fails to build using
toolchains in which gcc was configured --with-fp-32=xx with the
following error:
LDS arch/mips/vdso/vdso.lds
cc1: error: '-march=r3000' requires '-mfp32'
make[2]: *** [scripts/Makefile.build:379: arch/mips/vdso/vdso.lds] Error 1
The kernel proper avoids this error because we build with the
-msoft-float compiler flag, rather than using the compiler's default.
Pass this flag through to the VDSO build so that it too becomes agnostic
to the toolchain's floating point configuration.
Note that this is filtered out from KBUILD_CFLAGS rather than simply
always using -msoft-float such that if we switch the kernel to use
-mno-float in the future the VDSO will automatically inherit the change.
The VDSO doesn't actually include any floating point code, and its
.MIPS.abiflags section is already manually generated to specify that
it's compatible with any floating point ABI. As such this change should
have no effect on the resulting VDSO, apart from fixing the build
failure for affected toolchains.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Kevin Hilman <khilman@baylibre.com>
References: https://lore.kernel.org/linux-mips/1477843551-21813-1-git-send-email-linux@roeck-us.net/
References: https://kernelci.org/build/id/5c4e4ae059b5142a249ad004/logs/
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.4+
|
|
Don't set octeon_dma_bar_type if PCI is disabled. This avoids creation
of the MSI irqchip later on, and saves a bit of memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a214720cbf50 ("Disable MSI also when pcie-octeon.pcie_disable on")
Cc: stable@vger.kernel.org # v3.3+
Cc: linux-mips@vger.kernel.org
|
|
Add the Atom Tremont model number to the Intel family list.
[ Tony: Also update comment at head of file to say "_X" suffix is
also used for microserver parts. ]
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Megha Dey <megha.dey@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190125195902.17109-4-tony.luck@intel.com
|
|
Remove duplicate header which is included twice.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
We need the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the swapped outb() parameters in the KASLR code
- Fix the PKEY handling at fork which missed to preserve the pkey
state for the child. Comes with a test case to validate that.
- Fix the entry stack handling for XEN PV to respect that XEN PV
systems enter the function already on the current thread stack and
not on the trampoline.
- Fix kexec load failure caused by using a stale value when the
kexec_buf structure is reused for subsequent allocations.
- Fix a bogus sizeof() in the memory encryption code
- Enforce PCI dependency for the Intel Low Power Subsystem
- Enforce PCI_LOCKLESS_CONFIG when PCI is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Select PCI_LOCKLESS_CONFIG if PCI is enabled
x86/entry/64/compat: Fix stack switching for XEN PV
x86/kexec: Fix a kexec_file_load() failure
x86/mm/mem_encrypt: Fix erroneous sizeof()
x86/selftests/pkeys: Fork() to check for state being preserved
x86/pkeys: Properly copy pkey state at fork()
x86/kaslr: Fix incorrect i8254 outb() parameters
x86/intel/lpss: Make PCI dependency explicit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 timer fixes from Thomas Gleixner:
"Two commits which were missed to be sent during the merge window.
- The TSC calibration fix turns out to be more urgent as recent
Skylake-X systems seem to have massive trouble with calibration
disturbance. This should go back into stable for that reason and it
the risk of breakage is rather low.
- Drop an unused define"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Remove unused FSEC_PER_NSEC define
x86/tsc: Make calibration refinement more robust
|
|
This fixes the following warning at boot when the kernel is booted on a
board with more CPU cores than was configured in NR_CPUS:
smp_init_cpus: Core Count = 8
smp_init_cpus: Core Id = 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at include/linux/cpumask.h:121 smp_init_cpus+0x54/0x74
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.0.0-rc3-00015-g1459333f88a0 #124
Call Trace:
__warn$part$3+0x6a/0x7c
warn_slowpath_null+0x35/0x3c
smp_init_cpus+0x54/0x74
setup_arch+0x1c0/0x1d0
start_kernel+0x44/0x310
_startup+0x107/0x107
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Pull KVM fixes from Paolo Bonzini:
"Quite a few fixes for x86: nested virtualization save/restore, AMD
nested virtualization and virtual APIC, 32-bit fixes, an important fix
to restore operation on older processors, and a bunch of hyper-v
bugfixes. Several are marked stable.
There are also fixes for GCC warnings and for a GCC/objtool interaction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Mark expected switch fall-throughs
KVM: x86: fix TRACE_INCLUDE_PATH and remove -I. header search paths
KVM: selftests: check returned evmcs version range
x86/kvm/hyper-v: nested_enable_evmcs() sets vmcs_version incorrectly
KVM: VMX: Move vmx_vcpu_run()'s VM-Enter asm blob to a helper function
kvm: selftests: Fix region overlap check in kvm_util
kvm: vmx: fix some -Wmissing-prototypes warnings
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1
svm: Fix AVIC incomplete IPI emulation
svm: Add warning message for AVIC IPI invalid target
KVM: x86: WARN_ONCE if sending a PV IPI returns a fatal error
KVM: x86: Fix PV IPIs for 32-bit KVM host
x86/kvm/hyper-v: recommend using eVMCS only when it is enabled
x86/kvm/hyper-v: don't recommend doing reset via synthetic MSR
kvm: x86/vmx: Use kzalloc for cached_vmcs12
KVM: VMX: Use the correct field var when clearing VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
KVM: x86: Fix single-step debugging
x86/kvm/hyper-v: don't announce GUEST IDLE MSR support
|
|
Pull dma-mapping fix from Christoph Hellwig:
"Fix a xen-swiotlb regression on arm64"
* tag 'dma-mapping-5.0-2' of git://git.infradead.org/users/hch/dma-mapping:
arm64/xen: fix xen-swiotlb cache flushing
|
|
When building some xtensa config, I hit the following warning:
drivers/staging/mt7621-dts/Kconfig:4:warning: 'BUILTIN_DTB' has wrong type.
'select' only accept arguments of bool and tristate type
It is due to some arch use BUILTIN_DTB as a flag for the need to builtin
dtb but xtensa use it as a string for which dtb to bulltin.
But for this (which dtb to build), it is better to use
BUILTIN_DTB_SOURCE like other arch do.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
This patch fix a simple typo.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Otherwise it is impossible to enable CPUs after booting with 'maxcpus'
parameter.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Secondary CPU reset vector overlaps part of the double exception handler
code, resulting in weird crashes and hangups when running user code.
Move exception vectors one page up so that they don't clash with the
secondary CPU reset vector.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
- add missing memory barriers to the secondary CPU synchronization spin
loops; add comment to the matching memory barrier in the boot_secondary
and __cpu_die functions;
- use READ_ONCE/WRITE_ONCE to access cpu_start_id/cpu_start_ccount
instead of reading/writing them directly;
- re-initialize cpu_running every time before starting secondary CPU to
flush possible previous CPU startup results.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
According to the Schematic, the hardware of ci20 leads to uart3,
but not to uart2. Uart2 is miswritten in the original code.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips <linux-mips@vger.kernel.org>
Cc: linux-kernel <linux-kernel@vger.kernel.org>
Cc: devicetree@vger.kernel.org
Cc: robh+dt@kernel.org
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: mark.rutland@arm.com
Cc: malat@debian.org
Cc: ezequiel@collabora.co.uk
Cc: ulf.hansson@linaro.org
Cc: syq <syq@debian.org>
Cc: jiaxun.yang <jiaxun.yang@flygoat.com>
|
|
The interrupt number set in the devicetree node of the DMA driver was
wrong.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
This ratio is the most used among all other architectures and make
icache_hygiene libhugetlbfs test pass: this test mmap lots of
hugepages whose addresses, without this patch, reach the end of
the process user address space.
Signed-off-by: Alexandre Ghiti <aghiti@upmem.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
arch/x86/kvm/lapic.c:1037:27: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/lapic.c:1876:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/hyperv.c:1637:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/svm.c:4396:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/mmu.c:4372:36: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:3835:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/x86.c:7938:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:2015:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
arch/x86/kvm/vmx/vmx.c:1773:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
The reason of having -I. here is to make the incorrectly set
TRACE_INCLUDE_PATH working.
As the comment block in include/trace/define_trace.h says,
TRACE_INCLUDE_PATH should be a relative path to the define_trace.h
Fix the TRACE_INCLUDE_PATH, and remove the iffy include paths.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit e2e871ab2f02 ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version()
helper") broke EVMCS enablement: to set vmcs_version we now call
nested_get_evmcs_version() but this function checks
enlightened_vmcs_enabled flag which is not yet set so we end up returning
zero.
Fix the issue by re-arranging things in nested_enable_evmcs().
Fixes: e2e871ab2f02 ("x86/kvm/hyper-v: Introduce nested_get_evmcs_version() helper")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
...along with the function's STACK_FRAME_NON_STANDARD tag. Moving the
asm blob results in a significantly smaller amount of code that is
marked with STACK_FRAME_NON_STANDARD, which makes it far less likely
that gcc will split the function and trigger a spurious objtool warning.
As a bonus, removing STACK_FRAME_NON_STANDARD from vmx_vcpu_run() allows
the bulk of code to be properly checked by objtool.
Because %rbp is not loaded via VMCS fields, vmx_vcpu_run() must manually
save/restore the host's RBP and load the guest's RBP prior to calling
vmx_vmenter(). Modifying %rbp triggers objtool's stack validation code,
and so vmx_vcpu_run() is tagged with STACK_FRAME_NON_STANDARD since it's
impossible to avoid modifying %rbp.
Unfortunately, vmx_vcpu_run() is also a gigantic function that gcc will
split into separate functions, e.g. so that pieces of the function can
be inlined. Splitting the function means that the compiled Elf file
will contain one or more vmx_vcpu_run.part.* functions in addition to
a vmx_vcpu_run function. Depending on where the function is split,
objtool may warn about a "call without frame pointer save/setup" in
vmx_vcpu_run.part.* since objtool's stack validation looks for exact
names when whitelisting functions tagged with STACK_FRAME_NON_STANDARD.
Up until recently, the undesirable function splitting was effectively
blocked because vmx_vcpu_run() was tagged with __noclone. At the time,
__noclone had an unintended side effect that put vmx_vcpu_run() into a
separate optimization unit, which in turn prevented gcc from inlining
the function (or any of its own function calls) and thus eliminated gcc's
motivation to split the function. Removing the __noclone attribute
allowed gcc to optimize vmx_vcpu_run(), exposing the objtool warning.
Kudos to Qian Cai for root causing that the fnsplit optimization is what
caused objtool to complain.
Fixes: 453eafbe65f7 ("KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines")
Tested-by: Qian Cai <cai@lca.pw>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We get some warnings when building kernel with W=1:
arch/x86/kvm/vmx/vmx.c:426:5: warning: no previous prototype for ‘kvm_fill_hv_flush_list_func’ [-Wmissing-prototypes]
arch/x86/kvm/vmx/nested.c:58:6: warning: no previous prototype for ‘init_vmcs_shadow_fields’ [-Wmissing-prototypes]
Make them static to fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
to L1
kvm-unit-tests' eventinj "NMI failing on IDT" test results in NMI being
delivered to the host (L1) when it's running nested. The problem seems to
be: svm_complete_interrupts() raises 'nmi_injected' flag but later we
decide to reflect EXIT_NPF to L1. The flag remains pending and we do NMI
injection upon entry so it got delivered to L1 instead of L2.
It seems that VMX code solves the same issue in prepare_vmcs12(), this was
introduced with code refactoring in commit 5f3d5799974b ("KVM: nVMX: Rework
event injection and recovery").
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In case of incomplete IPI with invalid interrupt type, the current
SVM driver does not properly emulate the IPI, and fails to boot
FreeBSD guests with multiple vcpus when enabling AVIC.
Fix this by update APIC ICR high/low registers, which also
emulate sending the IPI.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Print warning message when IPI target ID is invalid due to one of
the following reasons:
* In logical mode: cluster > max_cluster (64)
* In physical mode: target > max_physical (512)
* Address is not present in the physical or logical ID tables
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM hypercalls return a negative value error code in case of a fatal
error, e.g. when the hypercall isn't supported or was made with invalid
parameters. WARN_ONCE on fatal errors when sending PV IPIs as any such
error all but guarantees an SMP system will hang due to a missing IPI.
Fixes: aaffcfd1e82d ("KVM: X86: Implement PV IPIs in linux guest")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The recognition of the KVM_HC_SEND_IPI hypercall was unintentionally
wrapped in "#ifdef CONFIG_X86_64", causing 32-bit KVM hosts to reject
any and all PV IPI requests despite advertising the feature. This
results in all KVM paravirtualized guests hanging during SMP boot due
to IPIs never being delivered.
Fixes: 4180bf1b655a ("KVM: X86: Implement "send IPI" hypercall")
Cc: stable@vger.kernel.org
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We shouldn't probably be suggesting using Enlightened VMCS when it's not
enabled (not supported from guest's point of view). Hyper-V on KVM seems
to be fine either way but let's be consistent.
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
System reset through synthetic MSR is not recommended neither by genuine
Hyper-V nor my QEMU.
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This changes the allocation of cached_vmcs12 to use kzalloc instead of
kmalloc. This removes the information leak found by Syzkaller (see
Reported-by) in this case and prevents similar leaks from happening
based on cached_vmcs12.
It also changes vmx_get_nested_state to copy out the full 4k VMCS12_SIZE
in copy_to_user rather than only the size of the struct.
Tested: rebuilt against head, booted, and ran the syszkaller repro
https://syzkaller.appspot.com/text?tag=ReproC&x=174efca3400000 without
observing any problems.
Reported-by: syzbot+ded1696f6b50b615b630@syzkaller.appspotmail.com
Fixes: 8fcc4b5923af5de58b80b53a069453b135693304
Cc: stable@vger.kernel.org
Signed-off-by: Tom Roeder <tmroeder@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
Fix a recently introduced bug that results in the wrong VMCS control
field being updated when applying a IA32_PERF_GLOBAL_CTRL errata.
Fixes: c73da3fcab43 ("KVM: VMX: Properly handle dynamic VM Entry/Exit controls")
Reported-by: Harald Arnesen <harald@skogtun.org>
Tested-by: Harald Arnesen <harald@skogtun.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HV_X64_MSR_GUEST_IDLE_AVAILABLE appeared in kvm_vcpu_ioctl_get_hv_cpuid()
by mistake: it announces support for HV_X64_MSR_GUEST_IDLE (0x400000F0)
which we don't support in KVM (yet).
Fixes: 2bc39970e932 ("x86/kvm/hyper-v: Introduce KVM_GET_SUPPORTED_HV_CPUID")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
ccount_timer_shutdown is called from the atomic context in the
secondary_start_kernel, resulting in the following BUG:
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
Preemption disabled at:
secondary_start_kernel+0xa1/0x130
Call Trace:
___might_sleep+0xe7/0xfc
__might_sleep+0x41/0x44
synchronize_irq+0x24/0x64
disable_irq+0x11/0x14
ccount_timer_shutdown+0x12/0x20
clockevents_switch_state+0x82/0xb4
clockevents_exchange_device+0x54/0x60
tick_check_new_device+0x46/0x70
clockevents_register_device+0x8c/0xc8
clockevents_config_and_register+0x1d/0x2c
local_timer_setup+0x75/0x7c
secondary_start_kernel+0xb4/0x130
should_never_return+0x32/0x35
Use disable_irq_nosync instead of disable_irq to avoid it.
This is safe because the ccount timer IRQ is per-CPU, and once IRQ is
masked the ISR will not be called.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
