| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When we configure CONFIG_ARM_LPAE=y, pfn << PAGE_SHIFT will
overflow if pfn >= 0x100000 in copy_oldmem_page.
So use __pfn_to_phys for converting.
Signed-off-by: Liu Hua <sdu.liu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use of tracers in local_irq_disable is causes abort loops when called
with irqs disabled using a temporary stack. Replace local_irq_disable
with raw_local_irq_disable instead to avoid tracers.
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Detect endianess directly on the hardware and use
ioread/iowrite functions.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Detect endianess directly on the hardware and use
ioread/iowrite functions.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
OPAL defines opal_msg as a big endian struct so we have to
byte swap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
opal_notifier_register() is missing a pending "unregister" variant
and should be exposed to modules.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Turn them on at the same time as we allow MSR_IR/DR in the paca
kernel MSR, ie, after the MMU has been setup enough to be able
to handle relocated access to the linear mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we take an interrupt such as a trap caused by a BUG_ON before the
MMU has been setup, the interrupt handlers try to enable virutal mode
and cause a recursive crash, making the original problem very hard
to debug.
This fixes it by adjusting the "kernel_msr" value in the PACA so that
it only has MSR_IR and MSR_DR (translation for instruction and data)
set after the MMU has been initialized for the processor.
We may still not have a console yet but at least we don't get into
a recursive fault (and early debug console or memory dump via JTAG
of the kernel buffer *will* give us the proper error).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
All our cpu feature updates were done for every CPU in the device-tree,
thus overwriting the cputable bits over and over again. Instead do them
only for the boot CPU.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Move the definition to setup-common.c and set the init value
to -1 on both 32 and 64-bit (it was 0 on 64-bit).
Additionally add a check to prom.c to garantee that the init
value has been udpated after the DT scan.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For historical reasons that code was under #ifdef CONFIG_PPC_PSERIES
but it applies equally to all 64-bit platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.
We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:
cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
pc: c000000000050074: restore_gprs+0xc0/0x148
lr: 00000000b52a8184
sp: ac57d360
msr: 8000000100201030
current = 0xc00000002c500000
paca = 0xc000000007dbfc00 softe: 0 irq_happened: 0x00
pid = 34535, comm = Pooled Thread #
R00 = 00000000b52a8184 R16 = 00000000b3e48fda
R01 = 00000000ac57d360 R17 = 00000000ade79bd8
R02 = 00000000ac586930 R18 = 000000000fac9bcc
R03 = 00000000ade60000 R19 = 00000000ac57f930
R04 = 00000000f6624918 R20 = 00000000ade79be8
R05 = 00000000f663f238 R21 = 00000000ac218a54
R06 = 0000000000000002 R22 = 000000000f956280
R07 = 0000000000000008 R23 = 000000000000007e
R08 = 000000000000000a R24 = 000000000000000c
R09 = 00000000b6e69160 R25 = 00000000b424cf00
R10 = 0000000000000181 R26 = 00000000f66256d4
R11 = 000000000f365ec0 R27 = 00000000b6fdcdd0
R12 = 00000000f66400f0 R28 = 0000000000000001
R13 = 00000000ada71900 R29 = 00000000ade5a300
R14 = 00000000ac2185a8 R30 = 00000000f663f238
R15 = 0000000000000004 R31 = 00000000f6624918
pc = c000000000050074 restore_gprs+0xc0/0x148
cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
lr = 00000000b52a8184
msr = 8000000100201030 cr = 24804888
ctr = 0000000000000000 xer = 0000000000000000 trap = 700
This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function. It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The current kernel code assumes big endian and parses RTAS events all
wrong. The most visible effect is that we cannot honor EPOW events,
meaning, for example, we cannot shut down a guest properly from the
hypervisor.
This new patch is largely inspired by Nathan's work: we get rid of all
the bit fields in the RTAS event structures (even the unused ones, for
consistency). We also introduce endian safe accessors for the fields used
by the kernel (trivial rtas_error_type() accessor added for consistency).
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The emulated (CONFIG_MATH_EMULATION_FULL)
PowerPC Floating Point instruction mtfsf
does not correctly copy bits from its source
register to the Floating Point Status and Register (FPSCR).
The error is in the preparation of the mask used to
select the bits to be copied from the source to the FPSCR.
Execution of the mtfsf instruction does not produce the same
results on a MPC8548 platform (emulated floating point)
as on MPC7410 or 440EP platforms (hardware floating point).
This error has been detected using a Freescale MPC8548
based platform and the patch below tested using that platform.
The patch is based on the patch(es) provided by
Gabriel Paubert and analysis by Gabriel, James Yang and David Laight.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Recent arm64 builds using CONFIG_ARM64_64K_PAGES are failing with:
arch/arm64/kernel/perf_regs.c: In function ‘perf_reg_abi’:
arch/arm64/kernel/perf_regs.c:41:2: error: implicit declaration of function ‘is_compat_thread’
arch/arm64/kernel/perf_event.c:1398:2: error: unknown type name ‘compat_uptr_t’
This is due to some recent arm64 perf commits with compat support:
commit 23c7d70d55c6d9:
ARM64: perf: add support for frame pointer unwinding in compat mode
commit 2ee0d7fd36a3f8:
ARM64: perf: add support for perf registers API
Those patches make the arm64 kernel unbuildable if CONFIG_COMPAT is not
defined and CONFIG_ARM64_64K_PAGES depends on !CONFIG_COMPAT. This patch
allows the arm64 kernel to build with and without CONFIG_COMPAT.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Pull arch/tile updates from Chris Metcalf:
"These fix a few stray build issues seen in linux-next, and also add
the minimal required support for perf to tilegx"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: remove unused variable 'devcap'
tile: Fix vDSO compilation issue with allyesconfig
perf tools: Allow building for tile
tile/perf: Support perf_events on tilegx and tilepro
tile: Enable NMIs on return from handle_nmi() without errors
tile: Add support for handling PMC hardware
tile: don't use __get_cpu_var() with structure-typed arguments
tile: avoid overflow in ns2cycles
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU upates from Joerg Roedel:
"This time a few more updates queued up.
- Rework VT-d code to support ACPI devices
- Improvements for memory and PCI hotplug support in the VT-d driver
- Device-tree support for OMAP IOMMU
- Convert OMAP IOMMU to use devm_* interfaces
- Fixed PASID support for AMD IOMMU
- Other random cleanups and fixes for OMAP, ARM-SMMU and SHMOBILE
IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support"
* tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (75 commits)
iommu/vt-d: Fix error handling in ANDD processing
iommu/vt-d: returning free pointer in get_domain_for_dev()
iommu/vt-d: Only call dmar_acpi_dev_scope_init() if DRHD units present
iommu/vt-d: Check for NULL pointer in dmar_acpi_dev_scope_init()
iommu/amd: Fix logic to determine and checking max PASID
iommu/vt-d: Include ACPI devices in iommu=pt
iommu/vt-d: Finally enable translation for non-PCI devices
iommu/vt-d: Remove to_pci_dev() in intel_map_page()
iommu/vt-d: Remove pdev from intel_iommu_attach_device()
iommu/vt-d: Remove pdev from iommu_no_mapping()
iommu/vt-d: Make domain_add_dev_info() take struct device
iommu/vt-d: Make domain_remove_one_dev_info() take struct device
iommu/vt-d: Rename 'hwdev' variables to 'dev' now that that's the norm
iommu/vt-d: Remove some pointless to_pci_dev() calls
iommu/vt-d: Make get_valid_domain_for_dev() take struct device
iommu/vt-d: Make iommu_should_identity_map() take struct device
iommu/vt-d: Handle RMRRs for non-PCI devices
iommu/vt-d: Make get_domain_for_dev() take struct device
iommu/vt-d: Make domain_context_mapp{ed,ing}() take struct device
iommu/vt-d: Make device_to_iommu() cope with non-PCI devices
...
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The legacy HAVE_PWM Kconfig symbol is finally being retired. Thanks a
lot to Sascha Hauer for doing that.
Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
Intel Low Power Subsystem.
An assortment of fixes and cleanups rounds things off for this release
cycle"
* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: pxa: Constify OF match table
pwm: pxa: Fix typo "pwm" -> "PWM"
Revert "pwm: pxa: Use of_match_ptr()"
pwm: add support for Intel Low Power Subsystem PWM
pwm: Add CLPS711X PWM support
pwm: atmel: correct CDTY calculation
pwm: atmel: Fix polarity handling
Documentation: Add device tree bindings for Freescale FTM PWM.
pwm: Add Freescale FTM PWM driver support
pwm: pxa: Use of_match_ptr()
pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
pwm: renesas-tpu: Add dependency on HAS_IOMEM
pwm: Remove obsolete HAVE_PWM Kconfig symbol
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
|
|
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board changes from Arnd Bergmann:
"As we continue to replace board files with device tree descriptions,
this part of the ARM support is getting smaller. We have basically
just defconfig changes here this time, and a significant number of
Renesas shmobile changes, as Renesas is still in the process of
deprecating board file support"
* tag 'boards-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
ARM: enable fhandle in multi_v7_defconfig
ARM: tegra: enable fhandle in tegra_defconfig
ARM: update multi_v7_defconfig for Tegra
ARM: add Marvell Dove and some drivers to multi_v7 defconfig
ARM: fix duplicate symbols in multi_v5_defconfig
ARM: pxa: add gpio keys information
ARM: tegra: defconfig updates
ARM: config: keystone: enable AEMIF/NAND support
ARM: qcom: Enable basic support for Qualcomm platforms in multi_v7_defconfig
ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
ARM: config: Add mvebu_v5_defconfig
ARM: config: Add a multi_v5_defconfig
ARM: shmobile: r7s72100: update defconfig for I2C usage
ARM: shmobile: Remove Lager DT reference legacy clock bits
ARM: shmobile: Remove Koelsch DT reference legacy clock bits
ARM: shmobile: Remove KZM9D board code
ARM: mvebu: update defconfigs for Armada 375 and 38x
ARM: dove: Enable watchdog support in the defconfig
ARM: mvebu: Enable watchdog support in defconfig
ARM: config: keystone: enable led support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"Lots of isolated bug fixes that were not found to be important enough
to be submitted before the merge window or backported into stable
kernels.
The vast majority of these came out of Arnd's randconfig testing and
just prevents running into build-time bugs in configurations that we
do not care about in practice"
* tag 'fixes-non-critical-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: at91: fix a typo
ARM: moxart: fix CPU selection
ARM: tegra: fix board DT pinmux setup
ARM: nspire: Fix compiler warning
IXP4xx: Fix DMA masks.
Revert "ARM: ixp4xx: Make dma_set_coherent_mask common, correct implementation"
IXP4xx: Fix Goramo Multilink GPIO conversion.
Revert "ARM: ixp4xx: fix gpio rework"
ARM: tegra: make debug_ll code build for ARMv6
ARM: sunxi: fix build for THUMB2_KERNEL
ARM: exynos: add missing include of linux/module.h
ARM: exynos: fix l2x0 saved regs handling
ARM: samsung: select CRC32 for SAMSUNG_PM_CHECK
ARM: samsung: select ATAGS where necessary
ARM: samsung: fix SAMSUNG_PM_DEBUG Kconfig logic
ARM: samsung: allow serial driver to be disabled
ARM: s5pv210: enable IDE support in MACH_TORBRECK
ARM: s5p64x0: fix building with only one soc type
ARM: s3c64xx: select power domains only when used
ARM: s3c64xx: MACH_SMDK6400 needs HSMMC1
...
|
|
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel
Pull Hexagon updates from Richard Kuo:
"Mostly cleanups for compilation with allmodconfig and some other
miscellaneous fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: update CR year for elf.h
Hexagon: remove SP macro
Hexagon: set ELF_EXEC_PAGESIZE to PAGE_SIZE
Hexagon: set the e_flags in user regset view for core dumps
Hexagon: fix atomic_set
Hexagon: add screen_info for VGA_CONSOLE
hexagon: correct type on pgd copy
smp, hexagon: kill SMP single function call interrupt
arch: hexagon: include: asm: add generic macro 'mmiowb' in "io.h"
arch: hexagon: kernel: hexagon_ksyms.c: export related symbols which various modules need
arch: hexagon: kernel: reset.c: use function pointer instead of function for pm_power_off and export it
arch: hexagon: include: asm: add "vga.h" in Kbuild
arch: hexagon: include: asm: Kbuild: add generic "serial.h" in Kbuild
arch: hexagon: include: uapi: asm: setup.h add swith macro __KERNEL__
arch: hexagon: include: asm: add prefix "hvm[ci]_" for all enum members in "hexagon_vm.h"
arch: hexagon: Kconfig: add HAVE_DMA_ATTR in Kconfig and remove "linux/dma-mapping.h" from "asm/dma-mapping.h"
arch: hexagon: kernel: add export symbol function __delay()
hexagon: include: asm: kgdb: extend DBG_MAX_REG_NUM for "cs0/1"
hexagon: kernel: kgdb: include related header for pass compiling.
hexagon: kernel: remove useless variables 'dn', 'r' and 'err' in time_init_deferred() in "time.c"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68k fixes from Greg Ungerer:
"Just a couple of fixes. Clean up compile warnings by using correct
types in function args, and clean out the removed CONFIG_MTD_PARTITIONS"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix arg types for outs* functions
m68k : Kill CONFIG_MTD_PARTITIONS
|
|
Despite the switch to right UART driver (prev patch), serial console
still doesn't work due to missing CONFIG_SERIAL_OF_PLATFORM
Also fix the default cmdline in DT to not refer to out-of-tree
ARC framebuffer driver for console.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.13, 3.14
Cc: Francois Bedard <Francois.Bedard@synopsys.com>
|
|
The Synopsys APB DW UART has a couple of special features that are not
in the System C model. In 3.8, the 8250_dw driver didn't really use these
features, but from 3.9 onwards, the 8250_dw driver has become incompatible
with our model.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.13, 3.14
Cc: Francois Bedard <Francois.Bedard@synopsys.com>
|
|
-Pass the expected arg to non-boot park'ing routine
(It worked so far because existing SMP backends don't use the arg)
-CONFIG_DEBUG_PREEMPT warning
|
|
This reverts commit 82b2f495fba338d1e3098dde1df54944a9c19751. The
__boot_cpu_mode variable is flushed in head.S after being written,
therefore the additional cache flushing is no longer required.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).
This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Various fbdev fixes and improvements, but nothing big"
* tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (38 commits)
fbdev: Make the switch from generic to native driver less alarming
Video: atmel: avoid the id of fix screen info is overwritten
video: imxfb: Add DT default contrast control register property.
video: atmel_lcdfb: ensure the hardware is initialized with the correct mode
fbdev: vesafb: add dev->remove() callback
fbdev: efifb: add dev->remove() callback
video: pxa3xx-gcu: switch to devres functions
video: pxa3xx-gcu: provide an empty .open call
video: pxa3xx-gcu: pass around struct device *
video: pxa3xx-gcu: rename some symbols
sisfb: fix 1280x720 resolution support
video: fbdev: uvesafb: Remove impossible code path in uvesafb_init_info
video: fbdev: uvesafb: Remove redundant NULL check in uvesafb_remove
fbdev: FB_OPENCORES should depend on HAS_DMA
OMAPDSS: convert pixel clock to common videomode style
OMAPDSS: Remove unused get_context_loss_count support
OMAPDSS: use DISPC register to detect context loss
video: da8xx-fb: Use "SIMPLE_DEV_PM_OPS" macro
video: imxfb: Convert to SIMPLE_DEV_PM_OPS
video: imxfb: Resolve mismatch between backlight/contrast
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"A number of cleanups plus support for the RDSEED instruction, which
will be showing up in Intel Broadwell CPU's"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: Add arch_has_random[_seed]()
random: If we have arch_get_random_seed*(), try it before blocking
random: Use arch_get_random_seed*() at init time and once a second
x86, random: Enable the RDSEED instruction
random: use the architectural HWRNG for the SHA's IV in extract_buf()
random: clarify bits/bytes in wakeup thresholds
random: entropy_bytes is actually bits
random: simplify accounting code
random: tighten bound on random_read_wakeup_thresh
random: forget lock in lockless accounting
random: simplify accounting logic
random: fix comment on "account"
random: simplify loop in random_read
random: fix description of get_random_bytes
random: fix comment on proc_do_uuid
random: fix typos / spelling errors in comments
|
|
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
The SP/r29 macro wasn't used anywhere else and was causing conflicts
with another module, so just remove it.
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Normal writes in our our architecture don't invalidate lock
reservations.
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
swapper_pg_dir is an array of pgd_t, not pgd_t*. This has no actual
effect since sizeof(pgd_t) == sizeof(pgd_t*), but unconfuses tools that
check types.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Commit 9a46ad6d6df3b54 "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one intterupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Need dumy mmiowb(), or can not pass compiling, the related error with
allmodconfig:
CC [M] drivers/mmc/host/sdhci.o
drivers/mmc/host/sdhci.c: In function 'sdhci_request':
drivers/mmc/host/sdhci.c:1409:2: error: implicit declaration of function 'mmiowb' [-Werror=implicit-function-declaration]
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
modules need
Need export all related functions and symbols for various modules with
allmodconfig. The related errors:
MODPOST 2879 modules
ERROR: "__vmyield" [sound/sound_firmware.ko] undefined!
ERROR: "__phys_offset" [sound/drivers/snd-dummy.ko] undefined!
ERROR: "ioremap_nocache" [drivers/char/ipmi/ipmi_si.ko] undefined!
ERROR: "__iounmap" [drivers/char/ipmi/ipmi_si.ko] undefined!
...
For including files, need "linux/*" first, then "asm/*". All related
included files and symbols need be sorted by alphabetical order.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
pm_power_off and export it
'pm_power_off' is a function pointer, not a function, so need change
its type, and also need export it, or can not pass compiling with
allmodconfig. The related error:
MODPOST 2879 modules
ERROR: "pm_power_off" [drivers/char/ipmi/ipmi_poweroff.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Need include generic "vga.h", or can not pass compiling with
allmodconfig, the related error:
CC [M] drivers/gpu/drm/drm_irq.o
In file included from include/linux/vgaarb.h:34:0,
from drivers/gpu/drm/drm_irq.c:42:
include/video/vga.h:22:21: fatal error: asm/vga.h: No such file or directory
Also move "preempt.h" upper to match sort order.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
|
Add "serial.h" in Kbuild, or can not pass compiling with allmodconfig,
the related error:
CC [M] drivers/staging/speakup/speakup_acntpc.o
In file included from drivers/staging/speakup/speakup_acntpc.c:33:0:
drivers/staging/speakup/serialio.h:7:24: fatal error: asm/serial.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
|
