| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enabling of Posted mode is seen to cause problems on dmtimer modules on AM33xx
(much like other OMAPs). Reference discussions on forums [1] [2]. Earlier
patch solving this on other OMAPs [3].
For OMAP SoCs with this errata, the fix has been to not enable Posted mode.
However, on some SoCs (atleast AM33xx) which carry this errata, Posted mode
is enabled on reset. So we not only need to ignore enabling of the POSTED bit
when the timer is requested, but also disable Posted mode if errata is present.
[1] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/285744.aspx
[2] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/270632.aspx
[3] http://www.spinics.net/lists/linux-omap/msg81770.html
Cc: stable@vgerk.kernel.org
Reported-by: Russ Dill <russ.dill@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We do not have REGULATOR_FIXED selected if no boards are selected
and we boot with device tree. This can cause various devices to
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull DRM fixes from Dave Airlie:
"I was going to leave this until post -rc1 but sysfs fixes broke
hotplug in userspace, so I had to fix it harder, otherwise a set of
pulls from intel, radeon and vmware,
The vmware/ttm changes are bit larger but since its early and they are
unlikely to break anything else I put them in, it lets vmware work
with dri3"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
drm/sysfs: fix hotplug regression since lifetime changes
drm/exynos: g2d: fix memory leak to userptr
drm/i915: Fix gen3 self-refresh watermarks
drm/ttm: Remove set_need_resched from the ttm fault handler
drm/ttm: Don't move non-existing data
drm/radeon: hook up backlight functions for CI and KV family.
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/vmwgfx: Make vmwgfx dma buffers prime aware
drm/vmwgfx: Make surfaces prime-aware
drm/vmwgfx: Hook up the prime ioctls
drm/ttm: Add a minimal prime implementation for ttm base objects
drm/vmwgfx: Fix false lockdep warning
drm/ttm: Allow execbuf util reserves without ticket
drm/i915: restore the early forcewake cleanup
...
|
|
Pull ARM fixes from Russell King:
"Some small fixes for this merge window, most of them quite self
explanatory - the biggest thing here is a fix for the ARMv7 LPAE
suspend/resume support"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7894/1: kconfig: select GENERIC_CLOCKEVENTS if HAVE_ARM_ARCH_TIMER
ARM: 7893/1: bitops: only emit .arch_extension mp if CONFIG_SMP
ARM: 7892/1: Fix warning for V7M builds
ARM: 7888/1: seccomp: not compatible with ARM OABI
ARM: 7886/1: make OABI default to off
ARM: 7885/1: Save/Restore 64-bit TTBR registers on LPAE suspend/resume
ARM: 7884/1: mm: Fix ECC mem policy printk
ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE
ARM: 7882/1: mm: fix __phys_to_virt to work with 64 bit phys_addr_t in BE case
ARM: 7881/1: __fixup_smp read of SCU config should do byteswap in BE case
ARM: Fix nommu.c build warning
|
|
Pull KVM fixes from Gleb Natapov.
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: kvm_clear_guest_page(): fix empty_zero_page usage
kvm: mmu: delay mmu audit activation
arm/arm64: KVM: Fix hyp mappings of vmalloc regions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull third set of powerpc updates from Benjamin Herrenschmidt:
"This is a small collection of random bug fixes and a few improvements
of Oops output which I deemed valuable enough to include as well.
The fixes are essentially recent build breakage and regressions, and a
couple of older bugs such as the DTL log duplication, the EEH issue
with PCI_COMMAND_MASTER and the problem with small contexts passed to
get/set_context with VSX enabled"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/signals: Mark VSX not saved with small contexts
powerpc/pseries: Fix SMP=n build of rng.c
powerpc: Make cpu_to_chip_id() available when SMP=n
powerpc/vio: Fix a dma_mask issue of vio
powerpc: booke: Fix build failures
powerpc: ppc64 address space capped at 32TB, mmap randomisation disabled
powerpc: Only print PACATMSCRATCH in oops when TM is active
powerpc/pseries: Duplicate dtl entries sometimes sent to userspace
powerpc: Remove a few lines of oops output
powerpc: Print DAR and DSISR on machine check oopses
powerpc: Fix __get_user_pages_fast() irq handling
powerpc/eeh: More accurate log
powerpc/eeh: Enable PCI_COMMAND_MASTER for PCI bridges
|
|
There are two code paths how page with pmd page table can be freed:
pmd_free() and pmd_free_tlb().
I've missed the second one and didn't add page table destructor call
there. It leads to leak of page->ptl for pmd page tables, if
dynamically allocated page->ptl is in use.
The patch adds the missed destructor and modifies documentation
accordingly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Tested-by: Andrey Vagin <avagin@openvz.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just a small pile of fixes for bugs and a few regressions. I'm still
trying to track down a driver load hang on my g33 (which infuriatingly
doesn't happen when loading the module manually after boot), somehow
bisecting loves to go astray on this one :( And there's a (harmless)
locking WARN in the suspend code due to one of Jesse's vlv backlight
rework patches. Otherwise nothing outstanding afaik.
* tag 'drm-intel-fixes-2013-11-20' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix gen3 self-refresh watermarks
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/i915: restore the early forcewake cleanup
Partially revert "drm/i915: tune the RC6 threshold for stability"
drm/i915: flush cursors harder
i915: Use 120MHz LVDS SSC clock for gen5/gen6/gen7
x86/early quirk: use gen6 stolen detection for VLV
drm/i915/dp: set sink to power down mode on dp disable
|
|
The VSX MSR bit in the user context indicates if the context contains VSX
state. Currently we set this when the process has touched VSX at any stage.
Unfortunately, if the user has not provided enough space to save the VSX state,
we can't save it but we currently still set the MSR VSX bit.
This patch changes this to clear the MSR VSX bit when the user doesn't provide
enough space. This indicates that there is no valid VSX state in the user
context.
This is needed to support get/set/make/swapcontext for applications that use
VSX but only provide a small context. For example, getcontext in glibc
provides a smaller context since the VSX registers don't need to be saved over
the glibc function call. But since the program calling getcontext may have
used VSX, the kernel currently says the VSX state is valid when it's not. If
the returned context is then used in setcontext (ie. a small context without
VSX but with MSR VSX set), the kernel will refuse the context. This situation
has been reported by the glibc community.
Based on patch from Carlos O'Donell.
Tested-by: Haren Myneni <haren@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In commit a489043 "Implement arch_get_random_long() based on H_RANDOM" I
broke the SMP=n build. We were getting plpar_wrappers.h via spinlock.h
which breaks when SMP=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Up until now we have only used cpu_to_chip_id() in the topology code,
which is only used on SMP builds. However my recent commit a4da0d5
"Implement arch_get_random_long/int() for powernv" added a usage when
SMP=n, breaking the build.
Move cpu_to_chip_id() into prom.c so it is available for SMP=n builds.
We would move the extern to prom.h, but that breaks the include in
topology.h. Instead we leave it in smp.h, but move it out of the
CONFIG_SMP #ifdef. We also need to include asm/smp.h in rng.c, because
the linux version skips asm/smp.h on UP. What a mess.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I encountered following issue:
[ 0.283035] ibmvscsi 30000015: couldn't initialize event pool
[ 5.688822] ibmvscsi: probe of 30000015 failed with error -1
which prevents the storage from being recognized, and the machine from
booting.
After some digging, it seems that it is caused by commit 4886c399da
as dma_mask pointer in viodev->dev is not set, so in
dma_set_mask_and_coherent(), dma_set_coherent_mask() is not called
because dma_set_mask(), which is dma_set_mask_pSeriesLP() returned EIO.
While before the commit, dma_set_coherent_mask() is always called.
I tried to replace dma_set_mask_and_coherent() with
dma_coerce_mask_and_coherent(), and the machine could boot again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
arch/powerpc/platforms/wsp/wsp.c: In function ‘wsp_probe_devices’:
arch/powerpc/platforms/wsp/wsp.c:76:3: error: implicit declaration of function ‘of_address_to_resource’ [-Werror=implicit-function-declaration]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit fba2369e6ceb (mm: use vm_unmapped_area() on powerpc architecture)
has a bug in slice_scan_available() where we compare an unsigned long
(high_slices) against a shifted int. As a result, comparisons against
the top 32 bits of high_slices (representing the top 32TB) always
returns 0 and the top of our mmap region is clamped at 32TB
This also breaks mmap randomisation since the randomised address is
always up near the top of the address space and it gets clamped down
to 32TB.
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If TM is not active there is no need to print PACATMSCRATCH
so we can save ourselves a line.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When reading from the dispatch trace log (dtl) userspace interface, I
sometimes see duplicate entries. One example:
# hexdump -C dtl.out
00000000 07 04 00 0c 00 00 48 44 00 00 00 00 00 00 00 00
00000010 00 0c a0 b4 16 83 6d 68 00 00 00 00 00 00 00 00
00000020 00 00 00 00 10 00 13 50 80 00 00 00 00 00 d0 32
00000030 07 04 00 0c 00 00 48 44 00 00 00 00 00 00 00 00
00000040 00 0c a0 b4 16 83 6d 68 00 00 00 00 00 00 00 00
00000050 00 00 00 00 10 00 13 50 80 00 00 00 00 00 d0 32
The problem is in scan_dispatch_log() where we call dtl_consumer()
but bail out before incrementing the index.
To fix this I moved dtl_consumer() after the timebase comparison.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We waste quite a few lines in our oops output:
...
MSR: 8000000000009032 <SF,EE,ME,IR,DR,RI> CR: 28044024 XER: 00000000
SOFTE: 0
CFAR: 0000000000009088
DAR: 000000000000001c, DSISR: 40000000
GPR00: c0000000000c74f0 c00000037cc1b010 c000000000d2bb30 0000000000000000
...
We can do a better job here and remove 3 lines:
MSR: 8000000000009032 <SF,EE,ME,IR,DR,RI> CR: 28044024 XER: 00000000
CFAR: 0000000000009088 DAR: 0000000000000010, DSISR: 40000000 SOFTE: 1
GPR00: c0000000000e3d10 c00000037cc2fda0 c000000000d2c3a8 0000000000000001
Also move PACATMSCRATCH up, it doesn't really belong in the stack
trace section.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Machine check exceptions set DAR and DSISR, so print them in our
oops output.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
__get_user_pages_fast() may be called with interrupts disabled (see e.g.
get_futex_key() in kernel/futex.c) and therefore should use local_irq_save()
and local_irq_restore() instead of local_irq_disable()/enable().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: <stable@vger.kernel.org> [v3.12]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This clarifies in the log whether the error is a global PHB error
or an individual PE being frozen.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On PHB3, we will fail to fetch IODA tables without PCI_COMMAND_MASTER
on PCI bridges. According to one experiment I had, the MSIx interrupts
didn't raise from the adapter without the bit applied to all upstream
PCI bridges including root port of the adapter. The patch forces to
have that bit enabled accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc LE updates from Ben Herrenschmidt:
"With my previous pull request I mentioned some remaining Little Endian
patches, notably support for our new ABI, which I was sitting on
making sure it was all finalized.
The toolchain folks confirmed it now, the new ABI is stable and merged
with gcc, so we are all good. Oh and we actually missed the actual
Kconfig switch for LE so here it is, along with a couple more bug
fixes.
I have more fixes but not related to LE so I'll send them as a
separate pull request tomorrow, let's get this one out of the way.
Note that this supports running user space binaries using the new ABI,
but the kernel itself still needs to be built with the old one. We'll
bring fixes for that after -rc1.
Here's Anton log that goes with this series:
This patch series adds support for the new ABI, LPAR support for
H_SET_MODE and finally adds a kconfig option and defconfig.
ABIv2 support was recently committed to binutils and gcc, and should
be merged into glibc soon. There are a number of very nice
improvements including the removal of function descriptors. Rusty's
kernel patches allow binaries of either ABI to work, easing the
transition"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Wrong DWARF CFI in the kernel vdso for little-endian / ELFv2
powerpc: Add pseries_le_defconfig
powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.
powerpc: Don't use ELFv2 ABI to build the kernel
powerpc: ELF2 binaries signal handling
powerpc: ELF2 binaries launched directly.
powerpc: Set eflags correctly for ELF ABIv2 core dumps.
powerpc: Add TIF_ELF2ABI flag.
pseries: Add H_SET_MODE to change exception endianness
powerpc/pseries: Fix endian issues in pseries EEH code
|
|
The ARM architected timer driver doesn't compile without
GENERIC_CLOCKEVENTS selected, so ensure that we select it when building
for a platform that has the timer.
Without this patch, mach-virt fails to build without something like
mach-vexpress also selected.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Uwe reported a build failure when targetting a NOMMU platform with my
recent prefetch changes:
arch/arm/lib/changebit.S: Assembler messages:
arch/arm/lib/changebit.S:15: Error: architectural extension `mp' is
not allowed for the current base architecture
This is due to use of the .arch_extension mp directive immediately prior
to an ALT_SMP(...) instruction. Whilst the ALT_SMP macro will expand to
nothing if !CONFIG_SMP, gas will still choke on the directive.
This patch fixes the issue by only emitting the sequence (including the
directive) if CONFIG_SMP=y.
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"It contains a few fixes and some work from Richard to make alpha
emulation under QEMU much more usable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Prevent a NULL ptr dereference in csum_partial_copy.
alpha: perf: fix out-of-bounds array access triggered from raw event
alpha: Use qemu+cserve provided high-res clock and alarm.
alpha: Switch to GENERIC_CLOCKEVENTS
alpha: Enable the rpcc clocksource for single processor
alpha: Reorganize rtc handling
alpha: Primitive support for CPU power down.
alpha: Allow HZ to be configured
alpha: Notice if we're being run under QEMU
alpha: Eliminate compiler warning from memset macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- revert an access_ok() patch which broke 32bit userspace on 64bit
kernels
- avoid a gcc miscompilation in two internal pa_memcpy() functions by
not inlining those
- do not export the definition of SOCK_NONBLOCK via uapi header (fixes
build of audit package)
- depending on the fault type we now correctly report either SIGBUS or
SIGSEGV
- a small fix to not compare a size_t variable for < 0
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: size_t is unsigned, so comparison size < 0 doesn't make sense.
parisc: improve SIGBUS/SIGSEGV error reporting
parisc: break out SOCK_NONBLOCK define to own asm header file
parisc: do not inline pa_memcpy() internal functions
Revert "parisc: implement full version of access_ok()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 updates from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: uapi: be sure of "_UAPI" prefix for all guard macros
avr32: add kprobe_ctlblk memory struct
avr32: fix out-of-range jump in large kernels
avr32: setup crt for early panic()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs bits and pieces from Al Viro:
"Assorted bits that got missed in the first pull request + fixes for a
couple of coredump regressions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fold try_to_ascend() into the sole remaining caller
dcache.c: get rid of pointless macros
take read_seqbegin_or_lock() and friends to seqlock.h
consolidate simple ->d_delete() instances
gfs2: endianness misannotations
dump_emit(): use __kernel_write(), not vfs_write()
dump_align(): fix the dumb braino
|
|
Note that pmds[i] is simply uninitialized at that point...
Granted, it's very hard to hit (you need split page locks *and*
kmalloc(sizeof(spinlock_t), GFP_KERNEL) failing), but the code is
obviously bogus.
Introduced by commit 09ef4939850a ("x86: add missed
pgtable_pmd_page_ctor/dtor calls for preallocated pmds")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I've finally tracked down why my CR signal-unwind test case still
fails on little-endian. The problem turned to be that the kernel
installs a signal trampoline in the vDSO, and provides a DWARF CFI
record for that trampoline. This CFI describes the save location
for CR:
rsave (70, 38*RSIZE + (RSIZE - CRSIZE))
which is correct for big-endian, but points to the wrong word on
little-endian. This is wrong no matter which ABI.
In addition, for the ELFv2 ABI, we should not only provide a CFI
record for register 70 (cr2), but for all CR fields separately.
Strictly speaking, I guess this would mean providing two separate
vDSO images, one for ELFv1 processes and one for ELFv2 processes (or
maybe playing some tricks with conditional DWARF expressions).
However, having CFI records for the other CR fields in ELFv1 is not
actually wrong, they just will be ignored. So it seems the simplest
fix would be just to always provide CFI for all the fields.
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With the little endian support merged, we can add the
CONFIG_CPU_LITTLE_ENDIAN kernel config option.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The kernel doesn't build correctly using the ELFv2 ABI. This patch
ensures that the ELFv1 ABI is used when building a kernel with an
ELFv2 enabled compiler.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For the ELFv2 ABI, the hander is the entry point, not a function descriptor.
We also need to set up r12, and fortunately the fast_exception_return
exit path restores r12 for us so nothing else is required.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No function descriptor, but we set r12 up and set TIF_RESTOREALL as it
normally isn't restored on return from syscall.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We leave it at zero (though it could be 1) for old tasks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
