summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)AuthorFilesLines
2010-01-25Merge branch 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds6-15/+18
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: Fix leak of free lapic date in kvm_arch_vcpu_init() KVM: x86: Fix probable memory leak of vcpu->arch.mce_banks KVM: S390: fix potential array overrun in intercept handling KVM: fix spurious interrupt with irqfd eventfd - allow atomic read and waitqueue remove KVM: MMU: bail out pagewalk on kvm_read_guest error KVM: properly check max PIC pin in irq route setup KVM: only allow one gsi per fd KVM: x86: Fix host_mapping_level() KVM: powerpc: Show timing option only on embedded KVM: Fix race between APIC TMR and IRR
2010-01-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds18-424/+749
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix IRQ ->set_affinity() methods. sparc: cpumask_of_node() should handle -1 as a node sparc64: Update defconfig. sparc: Add missing SW perf fault events. sparc64: Fully support both performance counters. sparc64: Add perf callchain support. sparc: convert to arch_gettimeoffset() sparc: leds_resource.end assigned to itself in clock_board_probe() sparc32: Fix page_to_phys(). sparc: Simplify param.h by simply including <asm-generic/param.h> sparc32: Update defconfig. SPARC: use helpers for rlimits sparc: copy_from_user() should not return -EFAULT
2010-01-25Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds23-131/+229
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (25 commits) OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timer PM debug: Fix warning when no CONFIG_DEBUG_FS OMAP3: PM: DSS PM_WKEN to refill DMA OMAP: timekeeping: time should not stop during suspend OMAP3: PM: Force write last pad config register into save area OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get() OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modules OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FS OMAP3: PM: Removing redundant and potentially dangerous PRCM configration OMAP3: Fixed ARM aux ctrl register save/restore OMAP3: CPUidle: Fixed timer resolution OMAP3: PM: Remove duplicate code blocks OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI OMAP3: PM: Enable system control module autoidle OMAP3: PM: Ack pending interrupts before entering suspend omap: Enable GPMC clock in gpmc_init OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0" OMAP4: clocks: Fix the clksel_rate struct DPLL divs OMAP4: PRCM: Fix the base address for CHIRONSS reg defines OMAP: dma_chan[lch_head].flag & OMAP_DMA_ACTIVE tested twice in omap_dma_unlink_lch() ...
2010-01-25KVM: x86: Fix leak of free lapic date in kvm_arch_vcpu_init()Wei Yongjun1-2/+3
In function kvm_arch_vcpu_init(), if the memory malloc for vcpu->arch.mce_banks is fail, it does not free the memory of lapic date. This patch fixed it. Cc: stable@kernel.org Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-25KVM: x86: Fix probable memory leak of vcpu->arch.mce_banksWei Yongjun1-0/+1
vcpu->arch.mce_banks is malloc in kvm_arch_vcpu_init(), but never free in any place, this may cause memory leak. So this patch fixed to free it in kvm_arch_vcpu_uninit(). Cc: stable@kernel.org Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-25KVM: S390: fix potential array overrun in intercept handlingChristian Borntraeger1-2/+2
kvm_handle_sie_intercept uses a jump table to get the intercept handler for a SIE intercept. Static code analysis revealed a potential problem: the intercept_funcs jump table was defined to contain (0x48 >> 2) entries, but we only checked for code > 0x48 which would cause an off-by-one array overflow if code == 0x48. Use the compiler and ARRAY_SIZE to automatically set the limits. Cc: stable@kernel.org Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-25KVM: MMU: bail out pagewalk on kvm_read_guest errorMarcelo Tosatti1-1/+3
Exit the guest pagetable walk loop if reading gpte failed. Otherwise its possible to enter an endless loop processing the previous present pte. Cc: stable@kernel.org Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-25KVM: x86: Fix host_mapping_level()Sheng Yang1-4/+2
When found a error hva, should not return PAGE_SIZE but the level... Also clean up the coding style of the following loop. Cc: stable@kernel.org Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-25KVM: powerpc: Show timing option only on embeddedAlexander Graf1-1/+1
Embedded PowerPC KVM has an exit timing implementation to track and evaluate how much time was spent in which exit path. For Book3S, we don't implement it. So let's not expose it as a config option either. Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Avi Kivity <avi@redhat.com>
2010-01-25KVM: Fix race between APIC TMR and IRRAvi Kivity1-5/+6
When we queue an interrupt to the local apic, we set the IRR before the TMR. The vcpu can pick up the IRR and inject the interrupt before setting the TMR, and perhaps even EOI it, causing incorrect behaviour. The race is really insignificant since it can only occur on the first interrupt (usually following interrupts will not change TMR), but it's better closed than open. Fixed by reordering setting the TMR vs IRR. Cc: stable@kernel.org Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
2010-01-21OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timerTero Kristo1-0/+13
OMAP GP timers keep running for a few cycles after they are stopped, which can cause the timer to expire and generate an interrupt. The pending interrupt will prevent e.g. OMAP from entering suspend, thus we ack it manually. Only applicable on OMAP2/3/4. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-21Merge branch 'for-linus/samsung' of git://git.fluff.org/bjdooks/linuxLinus Torvalds1-1/+1
* 'for-linus/samsung' of git://git.fluff.org/bjdooks/linux: hmt: adjust for new pwm_backlight->notify prototype
2010-01-22hmt: adjust for new pwm_backlight->notify prototypePeter Korsgaard1-1/+1
Commit cfc38999f (backlight: Pass device through notify callback) added a struct device argument to the notify callback, but didn't update the user of it in mach-hmt.c Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-01-21Merge branch 'perf-fixes-for-linus' of ↵Linus Torvalds3-3/+12
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: perf: x86: Add support for the ANY bit perf: Change the is_software_event() definition perf: Honour event state for aux stream data perf: Fix perf_event_do_pending() fallback callsite perf kmem: Print usage help for unknown commands perf kmem: Increase "Hit" column length hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change perf timechart: Use tid not pid for COMM change
2010-01-21Merge branch 'release' of ↵Linus Torvalds1-16/+6
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits) ACPI: delete acpi_processor_power_verify_c2() ACPI: allow C3 > 1000usec ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C ACPI: power_meter: remove double kfree() ACPI: processor: restrict early _PDC to opt-in platforms ACPI: Fix unused variable warning in sbs.c acpi: make ACPI device id constant sony-laptop - fix using of uninitialized variable ACPI: Fix section mismatch error for acpi_early_processor_set_pdc() eeepc-laptop: disable wireless hotplug for 1201N eeepc-laptop: add hotplug_disable parameter eeepc-laptop: switch to using sparse keymap library eeepc-laptop: dmi blacklist to disable pci hotplug code eeepc-laptop: disable cpu speed control on EeePC 701 ACPI: don't cond_resched if irq is disabled ACPI: Remove unnecessary cast. ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes ACPI: EC: Add wait for irq storm ACPI: SBS: Move SBS HC callback to faster Notify queue x86, ACPI: delete acpi_boot_table_init() return value ...
2010-01-21Merge branch 'sh/for-2.6.33' of ↵Linus Torvalds5-5/+7
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6 * 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: sh64: wire up sys_accept4. sh: unwire sys_recvmmsg. sh: ms7724: Correct sh-eth EEPROM polling timeout.
2010-01-21Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds12-57/+110
* master.kernel.org:/home/rmk/linux-2.6-arm: ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot() ARM: 5884/1: arm: Fix DCC console for v7 ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels" ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void) ARM: fix badly placed mach/plat entries in Kconfig & Makefile
2010-01-21perf: x86: Add support for the ANY bitStephane Eranian2-0/+8
Propagate the ANY bit into the fixed counter config for v3 and higher. Signed-off-by: Stephane Eranian <eranian@google.com> [a.p.zijlstra@chello.nl: split from larger patch] Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-01-20sparc64: Fix IRQ ->set_affinity() methods.David S. Miller1-9/+28
As noted by Benjamin Herrenschmidt, the generic IRQ layer only sets irq_desc[irq].affinity after ->set_affinity() succeeds. So we have to use the passed in cpumask. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20sparc: cpumask_of_node() should handle -1 as a nodeAnton Blanchard1-1/+3
pcibus_to_node can return -1 if we cannot determine which node a pci bus is on. If passed -1, cpumask_of_node will negatively index the lookup array and pull in random data: # cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus 00000000,00000003,00000000,00000000 # cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist 64-65 Change cpumask_of_node to check for -1 and return cpu_all_mask in this case: # cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus ffffffff,ffffffff,ffffffff,ffffffff # cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist 0-127 Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20Merge branch 'omap-fixes' into omap-fixes-for-linusTony Lindgren6-31/+66
2010-01-20Merge branch 'pm-fixes' of ↵Tony Lindgren9-45/+95
master.kernel.org:/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-fixes-for-linus
2010-01-20PM debug: Fix warning when no CONFIG_DEBUG_FSSergio Aguirre1-2/+2
Fix following warning when CONFIG_DEBUG_FS wasn't selected: arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: DSS PM_WKEN to refill DMASubramani Venkatesh1-0/+4
Currently, DSS does not wakeup when there is a DMA request. DSS wake up event must be enabled so that the DMA request to refill the FIFO will wake up the CORE domain. Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP: timekeeping: time should not stop during suspendKevin Hilman1-0/+26
During suspend, the kernel timekeeping subsystem is shut down. Before suspend and upon resume, it uses a weak function read_persistent_clock() to determine the amount of time that elapsed during suspend. This function was not implemented on OMAP, so from the timekeeping subsystem perspective (and thus userspace as well) it appeared that no time elapsed during suspend. This patch uses the 32k sync timer as a the persistent clock. NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so more than one wrapping of the 32k sync timer during suspend may cause problems. Also note there are not interrupts when the 32k sync timer wraps, so something else has to be done. Reported-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Force write last pad config register into save areaTero Kristo1-1/+10
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register (ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous OCP access to the SCM register area. Fixed by writing the last register to the save area. Also, optimized the delay loop for the HW save to include an udelay(1), which limits the number of unnecessary HW accesses to SCM register area during the save. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get()Roel Kluin1-2/+4
val is an u64 pointer, we need an int to check the error. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modulesPeter Ujfalusi1-2/+6
Wake-up from McBSP ports are needed, especially when the THRESHOLD dma mode is in use for audio playback. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FSManjunatha GK2-4/+6
The PM debug code fails to build on when CONFIG_DEBUG_FS is not enabled. Build error log: arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle': arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save' arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save' arch/arm/mach-omap2/built-in.o: In function `configure_vc': arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init' arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init' make: *** [.tmp_vmlinux1] Error 1 This patch fixes the above errors. Kernel booting is tested on omap zoom2 and zoom3 boards. Signed-off-by: Manjunatha GK <manjugk@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Removing redundant and potentially dangerous PRCM configrationSripathy, Vishwanath1-11/+0
As part of Core domain context restoration while coming out of off mode there are some registers being restored which are not required to be restored. ROM code will have restored them already. Overwriting some of them can have potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked. Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled. Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: Fixed ARM aux ctrl register save/restoreTero Kristo1-4/+9
Current value is stored on SDRAM and it is written back during wakeup. Previously a static value of 0x72 was written there. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Thara Gopinath <thara@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: CPUidle: Fixed timer resolutionTero Kristo1-1/+1
Previously used u32 as temporary data storage that wraps around at 4.294s. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Remove duplicate code blocksSanjeev Premi1-18/+0
This patch removes code blocks that are repeated in function prcm_setup_regs(). Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Disable interrupt controller AUTOIDLE before WFITero Kristo3-0/+16
OMAP interrupt controller goes to unknown state when there is right combination of l3,l4 sleep/wake-up transitions, l4 autoidle in interrupt controller and some interrupt. When this happens, interrupts are not delivered to ARM anymore and ARM will remain in WFI (wait for interrupt) until interrupt controller is forced to wake-up (i.e. lauterbach). Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Enable system control module autoidleTero Kristo1-0/+2
Enable the auto-idle feature of the SCM block to save some additional power. Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Ack pending interrupts before entering suspendTero Kristo3-0/+9
Suspending drivers may still generate interrupts just before their suspend is completed. Any pending interrupts here will prevent sleep. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20omap: Enable GPMC clock in gpmc_initOlof Johansson1-0/+2
Don't assume that gpmc_l3_clk is on, enable it before touching configuration registers. Note that the current code assumes that this clock is always enabled. We are already setting smart idle and L3 autogating for GPMC clock in gpmc_init. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-20sparc64: Update defconfig.David S. Miller1-31/+100
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20sparc: Add missing SW perf fault events.David S. Miller2-5/+20
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20sparc64: Fully support both performance counters.David S. Miller1-154/+353
Add the rest of the conflict detection and resolution logic necessary to support more than one counter at a time on sparc64. The structure and implementation closely mimicks that of powerpc. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20sparc64: Add perf callchain support.David S. Miller1-1/+119
Pretty straightforward, and it should be easy to add accurate walk through of signal stack frames in userspace. Signed-off-by: David S. Miller <davem@davemloft.net> Tested-by: Jens Axboe <jens.axboe@oracle.com>
2010-01-20OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0"Paul Walmsley1-3/+3
Commit 52650505fbf3a6ab851c801f54e73e76c55ab8da caused clock initialization to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate() with the clockfw spinlock held. Fix by accessing the rate directly from the internal clock framework functions. Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com>
2010-01-20OMAP4: clocks: Fix the clksel_rate struct DPLL divsRajendra Nayak1-31/+31
For all DPLL's the valid dividers are same as the values to be programmed in the register. 0 is an invalid value. The changes are generated by updating the script which autogenerates the file modifed in the patch. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-20OMAP4: PRCM: Fix the base address for CHIRONSS reg definesRajendra Nayak2-16/+18
The CHIRONSS has its own local PRCM module and the register defines need to use the CHIRONSS base and not the PRM base. The changes are generated by updating the script which autogenerates the file modifed in the patch. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-20Merge branch 'misc' into releaseLen Brown1-16/+6
2010-01-19OMAP: dma_chan[lch_head].flag & OMAP_DMA_ACTIVE tested twice in ↵Roel Kluin1-1/+1
omap_dma_unlink_lch() The same flag and bits were tested twice. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19omap3: Fix cpu detectionTony Lindgren2-18/+24
We need to set the omap_chip.oc carefully for the clocks to work. To fix this, set the omap_chip.oc in omap3_check_features() based on the CONTROL_IDCODE and silicon revision registers. Also add handling for 34xx es3.1.2 as es3.1 for now. Fixes booting on at least overo board. Based on an earlier patch by Paul Walmsley <paul@pwsan.com>. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19omap: Fix functions for dynamic remuxing of pinsTony Lindgren2-11/+35
Make the omap_mux_read and write available for board code, and rename omap_mux_set_board_signals into omap_mux_write_array. Also add the related prototypes and comments into mux.h. In some cases we want to change the signals dynamically, mostly for power management. Note that we cannot use the signal names as they are set __init to save memory. Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19omap: Fix cmdline muxingTony Lindgren1-2/+5
Looks like cmdline muxing got broken at some point when we decided to limit muxing to __init code. Currently omap_mux_entry list is not yet initialized when we try to initialize cmdline muxing. Fix this by calling omap_mux_init_list() before calling omap_mux_set_cmdline_signals(). Reported-by: Philip Balister <philip@balister.org> Tested-by: Philip Balister <philip@balister.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19OMAP3: clock: Remove unnecessarily .init initializers from OMAP3 clocksRussell King1-4/+0
The first thing that omap2_init_clksel_parent() does is check for a non-zero .clksel field in the struct clk. Therefore, it is pointless calling this function on clocks where the clksel field is unset. Remove init calls to omap2_init_clksel_parent() on clocks without a clksel field. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Paul Walmsley <paul@pwsan.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-09-07 18:39:37 +0000