| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
SCI instances found in SH SoCs have different spacing between registers
depending on the SoC. The platform data contains a regshift field that
tells the driver by how many bits to shift the register offset to
compute its address. We can compute the regshift value automatically
based on the memory resource size, there's no need to pass the value
through platform data.
Fix the sh7750 SCI and sh7760 SIM port memory resources length to ensure
proper computation of the regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the datasheets, the sh7760 SIM and sh7723 SCIFA instances
don't implement the REIE bit. Don't set it in platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bit is only set by platforms that also set the CKE1 but, in which
case its value is ignored by the device. Don't set it, this simplifies
platform data and only leaves the CKE1 bit to be handled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver considers all negative or zero values of the port_reg field
as invalid. The four platforms that set the field to a register address
all use an address higher than 0x7fffffff, which is thus considered by
the driver as invalid. The feature is thus never used, remove it.
The feature could be implemented properly in the future using the
pinctrl and GPIO APIs if desired.
While at it, don't set the field to SCIx_NOT_SUPPORTED (-1) either,
leaving it unset leads to the same result. This will allow removing the
SCIx_NOT_SUPPORTED macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The flag is set by the driver internally, don't set it in platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SCIF ports on sh7264 and sh7269 don't support the TOIE bit according
to the datasheets.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The scscr platform data field is used by the driver in three locations.
One of them masks out all bits except SCSCR_REIE. The two other are the
set_termios handler and the console write handler.
The set_termios handler calls sci_start_rx() to enable the receiver,
which sets the RIE bit unconditionally. It then calls sci_port_disable()
that effectively disables both the transmitter and the receiver. The
TIE bit will thus get set later when the serial cores reenables the
serial port.
The console write handler runs with interrupts disabled, and saves and
restores the SCSCR register value. The RIE and TIE bits are thus not
needed there.
The bits are thus not necessary in platform data, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bits are set by the driver internally, don't set them in platform
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- unwinder fixes
- AMD CPU topology enumeration fixes
- microcode loader fixes
- x86 embedded platform fixes
- fix for a bootup crash that may trigger when clearcpuid= is used
with invalid values"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Use compatible types in comparison to fix sparse error
x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
x86/entry: Fix the end of the stack for newly forked tasks
x86/unwind: Include __schedule() in stack traces
x86/unwind: Disable KASAN checks for non-current tasks
x86/unwind: Silence warnings for non-current tasks
x86/microcode/intel: Use correct buffer size for saving microcode data
x86/microcode/intel: Fix allocation size of struct ucode_patch
x86/microcode/intel: Add a helper which gives the microcode revision
x86/microcode: Use native CPUID to tickle out microcode revision
x86/CPU: Add native CPUID variants returning a single datum
x86/boot: Add missing declaration of string functions
x86/CPU/AMD: Fix Bulldozer topology
x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
x86/cpu: Fix typo in the comment for Anniedale
x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc race fixes uncovered by fuzzing efforts, a Sparse fix, two PMU
driver fixes, plus miscellanous tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Reject non sampling events with precise_ip
perf/x86/intel: Account interrupts for PEBS errors
perf/core: Fix concurrent sys_perf_event_open() vs. 'move_group' race
perf/core: Fix sys_perf_event_open() vs. hotplug
perf/x86/intel: Use ULL constant to prevent undefined shift behaviour
perf/x86/intel/uncore: Fix hardcoded socket 0 assumption in the Haswell init code
perf/x86: Set pmu->module in Intel PMU modules
perf probe: Fix to probe on gcc generated symbols for offline kernel
perf probe: Fix --funcs to show correct symbols for offline module
perf symbols: Robustify reading of build-id from sysfs
perf tools: Install tools/lib/traceevent plugins with install-bin
tools lib traceevent: Fix prev/next_prio for deadline tasks
perf record: Fix --switch-output documentation and comment
perf record: Make __record_options static
tools lib subcmd: Add OPT_STRING_OPTARG_SET option
perf probe: Fix to get correct modname from elf header
samples/bpf trace_output_user: Remove duplicate sys/ioctl.h include
samples/bpf sock_example: Avoid getting ethhdr from two includes
perf sched timehist: Show total scheduling time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"A number of regression fixes:
- Fix a boot hang on machines that have somewhat unusual memory map
entries of phys_addr=0x0 num_pages=0, which broke due to a recent
commit. This commit got cherry-picked from the v4.11 queue because
the bug is affecting real machines.
- Fix a boot hang also reported by KASAN, caused by incorrect init
ordering introduced by a recent optimization.
- Fix a recent robustification fix to allocate_new_fdt_and_exit_boot()
that introduced an invalid assumption. Neither bugs were seen in
the wild AFAIK"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Prune invalid memory map entries and fix boot regression
x86/efi: Don't allocate memmap through memblock after mm_init()
efi/libstub/arm*: Pass latest memory map to the kernel
|
|
Some machines, such as the Lenovo ThinkPad W541 with firmware GNET80WW
(2.28), include memory map entries with phys_addr=0x0 and num_pages=0.
These machines fail to boot after the following commit,
commit 8e80632fb23f ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Fix this by removing such bogus entries from the memory map.
Furthermore, currently the log output for this case (with efi=debug)
looks like:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0xffffffffffffffff] (0MB)
This is clearly wrong, and also not as informative as it could be. This
patch changes it so that if we find obviously invalid memory map
entries, we print an error and skip those entries. It also detects the
display of the address range calculation overflow, so the new output is:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[0x0000000000000000-0x0000000000000000] (invalid)
It also detects memory map sizes that would overflow the physical
address, for example phys_addr=0xfffffffffffff000 and
num_pages=0x0200000000000001, and prints:
[ 0.000000] efi: [Firmware Bug]: Invalid EFI memory map entries:
[ 0.000000] efi: mem45: [Reserved | | | | | | | | | | | | ] range=[phys_addr=0xfffffffffffff000-0x20ffffffffffffffff] (invalid)
It then removes these entries from the memory map.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ardb: refactor for clarity with no functional changes, avoid PAGE_SHIFT]
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[Matt: Include bugzilla info in commit log]
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191121
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
As Peter suggested [1] rejecting non sampling PEBS events,
because they dont make any sense and could cause bugs
in the NMI handler [2].
[1] http://lkml.kernel.org/r/20170103094059.GC3093@worktop
[2] http://lkml.kernel.org/r/1482931866-6018-3-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20170103142454.GA26251@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It's possible to set up PEBS events to get only errors and not
any data, like on SNB-X (model 45) and IVB-EP (model 62)
via 2 perf commands running simultaneously:
taskset -c 1 ./perf record -c 4 -e branches:pp -j any -C 10
This leads to a soft lock up, because the error path of the
intel_pmu_drain_pebs_nhm() does not account event->hw.interrupt
for error PEBS interrupts, so in case you're getting ONLY
errors you don't have a way to stop the event when it's over
the max_samples_per_tick limit:
NMI watchdog: BUG: soft lockup - CPU#22 stuck for 22s! [perf_fuzzer:5816]
...
RIP: 0010:[<ffffffff81159232>] [<ffffffff81159232>] smp_call_function_single+0xe2/0x140
...
Call Trace:
? trace_hardirqs_on_caller+0xf5/0x1b0
? perf_cgroup_attach+0x70/0x70
perf_install_in_context+0x199/0x1b0
? ctx_resched+0x90/0x90
SYSC_perf_event_open+0x641/0xf90
SyS_perf_event_open+0x9/0x10
do_syscall_64+0x6c/0x1f0
entry_SYSCALL64_slow_path+0x25/0x25
Add perf_event_account_interrupt() which does the interrupt
and frequency checks and call it from intel_pmu_drain_pebs_nhm()'s
error path.
We keep the pending_kill and pending_wakeup logic only in the
__perf_event_overflow() path, because they make sense only if
there's any data to deliver.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1482931866-6018-2-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
info->si_addr is of type void __user *, so it should be compared against
something from the same address space.
This fixes the following sparse error:
arch/x86/mm/mpx.c:296:27: error: incompatible types in comparison expression (different address spaces)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The Intel Denverton microserver uses a 25 MHz TSC crystal,
so we can derive its exact [*] TSC frequency
using CPUID and some arithmetic, eg.:
TSC: 1800 MHz (25000000 Hz * 216 / 3 / 1000000)
[*] 'exact' is only as good as the crystal, which should be +/- 20ppm
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/306899f94804aece6d8fa8b4223ede3b48dbb59c.1484287748.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull KVM fixes from Paolo Bonzini:
- fix for module unload vs deferred jump labels (note: there might be
other buggy modules!)
- two NULL pointer dereferences from syzkaller
- also syzkaller: fix emulation of fxsave/fxrstor/sgdt/sidt, problem
made worse during this merge window, "just" kernel memory leak on
releases
- fix emulation of "mov ss" - somewhat serious on AMD, less so on Intel
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix emulation of "MOV SS, null selector"
KVM: x86: fix NULL deref in vcpu_scan_ioapic
KVM: eventfd: fix NULL deref irqbypass consumer
KVM: x86: Introduce segmented_write_std
KVM: x86: flush pending lapic jump label updates on module unload
jump_labels: API for flushing deferred jump label updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix huge_ptep_set_access_flags() to return "changed" when any of the
ptes in the contiguous range is changed, not just the last one
- Fix the adr_l assembly macro to work in modules under KASLR
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: assembler: make adr_l work in modules under KASLR
arm64: hugetlb: fix the wrong return value for huge_ptep_set_access_flags
|
|
When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded
modules and the core kernel may exceed 4 GB, putting symbols exported
by the core kernel out of the reach of the ordinary adrp/add instruction
pairs used to generate relative symbol references. So make the adr_l
macro emit a movz/movk sequence instead when executing in module context.
While at it, remove the pointless special case for the stack pointer.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This is CVE-2017-2583. On Intel this causes a failed vmentry because
SS's type is neither 3 nor 7 (even though the manual says this check is
only done for usable SS, and the dmesg splat says that SS is unusable!).
On AMD it's worse: svm.c is confused and sets CPL to 0 in the vmcb.
The fix fabricates a data segment descriptor when SS is set to a null
selector, so that CPL and SS.DPL are set correctly in the VMCS/vmcb.
Furthermore, only allow setting SS to a NULL selector if SS.RPL < 3;
this in turn ensures CPL < 3 because RPL must be equal to CPL.
Thanks to Andy Lutomirski and Willy Tarreau for help in analyzing
the bug and deciphering the manuals.
Reported-by: Xiaohan Zhang <zhangxiaohan1@huawei.com>
Fixes: 79d5b4c3cd809c770d4bf9812635647016c56011
Cc: stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Reported by syzkaller:
BUG: unable to handle kernel NULL pointer dereference at 00000000000001b0
IP: _raw_spin_lock+0xc/0x30
PGD 3e28eb067
PUD 3f0ac6067
PMD 0
Oops: 0002 [#1] SMP
CPU: 0 PID: 2431 Comm: test Tainted: G OE 4.10.0-rc1+ #3
Call Trace:
? kvm_ioapic_scan_entry+0x3e/0x110 [kvm]
kvm_arch_vcpu_ioctl_run+0x10a8/0x15f0 [kvm]
? pick_next_task_fair+0xe1/0x4e0
? kvm_arch_vcpu_load+0xea/0x260 [kvm]
kvm_vcpu_ioctl+0x33a/0x600 [kvm]
? hrtimer_try_to_cancel+0x29/0x130
? do_nanosleep+0x97/0xf0
do_vfs_ioctl+0xa1/0x5d0
? __hrtimer_init+0x90/0x90
? do_nanosleep+0x5b/0xf0
SyS_ioctl+0x79/0x90
do_syscall_64+0x6e/0x180
entry_SYSCALL64_slow_path+0x25/0x25
RIP: _raw_spin_lock+0xc/0x30 RSP: ffffa43688973cc0
The syzkaller folks reported a NULL pointer dereference due to
ENABLE_CAP succeeding even without an irqchip. The Hyper-V
synthetic interrupt controller is activated, resulting in a
wrong request to rescan the ioapic and a NULL pointer dereference.
#include <sys/ioctl.h>
#include <sys/mman.h>
#include <sys/types.h>
#include <linux/kvm.h>
#include <pthread.h>
#include <stddef.h>
#include <stdint.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#ifndef KVM_CAP_HYPERV_SYNIC
#define KVM_CAP_HYPERV_SYNIC 123
#endif
void* thr(void* arg)
{
struct kvm_enable_cap cap;
cap.flags = 0;
cap.cap = KVM_CAP_HYPERV_SYNIC;
ioctl((long)arg, KVM_ENABLE_CAP, &cap);
return 0;
}
int main()
{
void *host_mem = mmap(0, 0x1000, PROT_READ|PROT_WRITE,
MAP_PRIVATE|MAP_ANONYMOUS, -1, 0);
int kvmfd = open("/dev/kvm", 0);
int vmfd = ioctl(kvmfd, KVM_CREATE_VM, 0);
struct kvm_userspace_memory_region memreg;
memreg.slot = 0;
memreg.flags = 0;
memreg.guest_phys_addr = 0;
memreg.memory_size = 0x1000;
memreg.userspace_addr = (unsigned long)host_mem;
host_mem[0] = 0xf4;
ioctl(vmfd, KVM_SET_USER_MEMORY_REGION, &memreg);
int cpufd = ioctl(vmfd, KVM_CREATE_VCPU, 0);
struct kvm_sregs sregs;
ioctl(cpufd, KVM_GET_SREGS, &sregs);
sregs.cr0 = 0;
sregs.cr4 = 0;
sregs.efer = 0;
sregs.cs.selector = 0;
sregs.cs.base = 0;
ioctl(cpufd, KVM_SET_SREGS, &sregs);
struct kvm_regs regs = { .rflags = 2 };
ioctl(cpufd, KVM_SET_REGS, ®s);
ioctl(vmfd, KVM_CREATE_IRQCHIP, 0);
pthread_t th;
pthread_create(&th, 0, thr, (void*)(long)cpufd);
usleep(rand() % 10000);
ioctl(cpufd, KVM_RUN, 0);
pthread_join(th, 0);
return 0;
}
This patch fixes it by failing ENABLE_CAP if without an irqchip.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 5c919412fe61 (kvm/x86: Hyper-V synthetic interrupt controller)
Cc: stable@vger.kernel.org # 4.5+
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Introduces segemented_write_std.
Switches from emulated reads/writes to standard read/writes in fxsave,
fxrstor, sgdt, and sidt. This fixes CVE-2017-2584, a longstanding
kernel memory leak.
Since commit 283c95d0e389 ("KVM: x86: emulate FXSAVE and FXRSTOR",
2016-11-09), which is luckily not yet in any final release, this would
also be an exploitable kernel memory *write*!
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Fixes: 96051572c819194c37a8367624b285be10297eca
Fixes: 283c95d0e3891b64087706b344a4b545d04a6e62
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM's lapic emulation uses static_key_deferred (apic_{hw,sw}_disabled).
These are implemented with delayed_work structs which can still be
pending when the KVM module is unloaded. We've seen this cause kernel
panics when the kvm_intel module is quickly reloaded.
Use the new static_key_deferred_flush() API to flush pending updates on
module unload.
Signed-off-by: David Matlack <dmatlack@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When unwinding a task, the end of the stack is always at the same offset
right below the saved pt_regs, regardless of which syscall was used to
enter the kernel. That convention allows the unwinder to verify that a
stack is sane.
However, newly forked tasks don't always follow that convention, as
reported by the following unwinder warning seen by Dave Jones:
WARNING: kernel stack frame pointer at ffffc90001443f30 in kworker/u8:8:30468 has bad value (null)
The warning was due to the following call chain:
(ftrace handler)
call_usermodehelper_exec_async+0x5/0x140
ret_from_fork+0x22/0x30
The problem is that ret_from_fork() doesn't create a stack frame before
calling other functions. Fix that by carefully using the frame pointer
macros.
In addition to conforming to the end of stack convention, this also
makes related stack traces more sensible by making it clear to the user
that ret_from_fork() was involved.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/8854cdaab980e9700a81e9ebf0d4238e4bbb68ef.1483978430.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the following commit:
0100301bfdf5 ("sched/x86: Rewrite the switch_to() code")
... the layout of the 'inactive_task_frame' struct was designed to have
a frame pointer header embedded in it, so that the unwinder could use
the 'bp' and 'ret_addr' fields to report __schedule() on the stack (or
ret_from_fork() for newly forked tasks which haven't actually run yet).
Finish the job by changing get_frame_pointer() to return a pointer to
inactive_task_frame's 'bp' field rather than 'bp' itself. This allows
the unwinder to start one frame higher on the stack, so that it properly
reports __schedule().
Reported-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/598e9f7505ed0aba86e8b9590aa528c6c7ae8dcd.1483978430.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are a handful of callers to save_stack_trace_tsk() and
show_stack() which try to unwind the stack of a task other than current.
In such cases, it's remotely possible that the task is running on one
CPU while the unwinder is reading its stack from another CPU, causing
the unwinder to see stack corruption.
These cases seem to be mostly harmless. The unwinder has checks which
prevent it from following bad pointers beyond the bounds of the stack.
So it's not really a bug as long as the caller understands that
unwinding another task will not always succeed.
In such cases, it's possible that the unwinder may read a KASAN-poisoned
region of the stack. Account for that by using READ_ONCE_NOCHECK() when
reading the stack of another task.
Use READ_ONCE() when reading the stack of the current task, since KASAN
warnings can still be useful for finding bugs in that case.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4c575eb288ba9f73d498dfe0acde2f58674598f1.1483978430.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are a handful of callers to save_stack_trace_tsk() and
show_stack() which try to unwind the stack of a task other than current.
In such cases, it's remotely possible that the task is running on one
CPU while the unwinder is reading its stack from another CPU, causing
the unwinder to see stack corruption.
These cases seem to be mostly harmless. The unwinder has checks which
prevent it from following bad pointers beyond the bounds of the stack.
So it's not really a bug as long as the caller understands that
unwinding another task will not always succeed.
Since stack "corruption" on another task's stack isn't necessarily a
bug, silence the warnings when unwinding tasks other than current.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/00d8c50eea3446c1524a2a755397a3966629354c.1483978430.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a regression in aesni that renders it useless if it's
built-in with a modular pcbc configuration"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - Fix failure when built-in with modular pcbc
|
|
When x86_pmu.num_counters is 32 the shift of the integer constant 1 is
exceeding 32bit and therefor undefined behaviour.
Fix this by shifting 1ULL instead of 1.
Reported-by: CoverityScan CID#1192105 ("Bad bit shift operation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: http://lkml.kernel.org/r/20170111114310.17928-1-colin.king@canonical.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
code
hswep_uncore_cpu_init() uses a hardcoded physical package id 0 for the boot
cpu. This works as long as the boot CPU is actually on the physical package
0, which is normaly the case after power on / reboot.
But it fails with a NULL pointer dereference when a kdump kernel is started
on a secondary socket which has a different physical package id because the
locigal package translation for physical package 0 does not exist.
Use the logical package id of the boot cpu instead of hard coded 0.
[ tglx: Rewrote changelog once more ]
Fixes: cf6d445f6897 ("perf/x86/uncore: Track packages, not per CPU data")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Harish Chegondi <harish.chegondi@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1483628965-2890-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In current code, the @changed always returns the last one's status for
the huge page with the contiguous bit set. This is really not what we
want. Even one of the PTEs is changed, we should tell it to the caller.
This patch fixes this issue.
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Cc: <stable@vger.kernel.org> # 4.5.x-
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In generic_load_microcode(), curr_mc_size is the size of the last
allocated buffer and since we have this performance "optimization"
there to vmalloc a new buffer only when the current one is bigger,
curr_mc_size ends up becoming the size of the biggest buffer we've seen
so far.
However, we end up saving the microcode patch which matches our CPU
and its size is not curr_mc_size but the respective mc_size during the
iteration while we're staring at it.
So save that mc_size into a separate variable and use it to store the
previously found microcode buffer.
Without this fix, we could get oops like this:
BUG: unable to handle kernel paging request at ffffc9000e30f000
IP: __memcpy+0x12/0x20
...
Call Trace:
? kmemdup+0x43/0x60
__alloc_microcode_buf+0x44/0x70
save_microcode_patch+0xd4/0x150
generic_load_microcode+0x1b8/0x260
request_microcode_user+0x15/0x20
microcode_write+0x91/0x100
__vfs_write+0x34/0x120
vfs_write+0xc1/0x130
SyS_write+0x56/0xc0
do_syscall_64+0x6c/0x160
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: 06b8534cb728 ("x86/microcode: Rework microcode loading")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/4f33cbfd-44f2-9bed-3b66-7446cd14256f@ce.jp.nec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We allocate struct ucode_patch here. @size is the size of microcode data
and used for kmemdup() later in this function.
Fixes: 06b8534cb728 ("x86/microcode: Rework microcode loading")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/7a730dc9-ac17-35c4-fe76-dfc94e5ecd95@ce.jp.nec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Since on Intel we're required to do CPUID(1) first, before reading
the microcode revision MSR, let's add a special helper which does the
required steps so that we don't forget to do them next time, when we
want to read the microcode revision.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20170109114147.5082-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Intel supplies the microcode revision value in MSR 0x8b
(IA32_BIOS_SIGN_ID) after CPUID(1) has been executed. Execute it each
time before reading that MSR.
It used to do sync_core() which did do CPUID but
c198b121b1a1 ("x86/asm: Rewrite sync_core() to use IRET-to-self")
changed the sync_core() implementation so we better make the microcode
loading case explicit, as the SDM documents it.
Reported-and-tested-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20170109114147.5082-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
... similarly to the cpuid_<reg>() variants.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20170109114147.5082-2-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull networking fixes from David Miller:
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
|
|
Add the missing declarations of basic string functions to string.h to allow
a clean build.
Fixes: 5be865661516 ("String-handling functions for the new x86 setup code.")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the following commit:
4bc9f92e64c8 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
... efi_bgrt_init() calls into the memblock allocator through
efi_mem_reserve() => efi_arch_mem_reserve() *after* mm_init() has been called.
Indeed, KASAN reports a bad read access later on in efi_free_boot_services():
BUG: KASAN: use-after-free in efi_free_boot_services+0xae/0x24c
at addr ffff88022de12740
Read of size 4 by task swapper/0/0
page:ffffea0008b78480 count:0 mapcount:-127
mapping: (null) index:0x1 flags: 0x5fff8000000000()
[...]
Call Trace:
dump_stack+0x68/0x9f
kasan_report_error+0x4c8/0x500
kasan_report+0x58/0x60
__asan_load4+0x61/0x80
efi_free_boot_services+0xae/0x24c
start_kernel+0x527/0x562
x86_64_start_reservations+0x24/0x26
x86_64_start_kernel+0x157/0x17a
start_cpu+0x5/0x14
The instruction at the given address is the first read from the memmap's
memory, i.e. the read of md->type in efi_free_boot_services().
Note that the writes earlier in efi_arch_mem_reserve() don't splat because
they're done through early_memremap()ed addresses.
So, after memblock is gone, allocations should be done through the "normal"
page allocator. Introduce a helper, efi_memmap_alloc() for this. Use
it from efi_arch_mem_reserve(), efi_free_boot_services() and, for the sake
of consistency, from efi_fake_memmap() as well.
Note that for the latter, the memmap allocations cease to be page aligned.
This isn't needed though.
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.9
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 4bc9f92e64c8 ("x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data")
Link: http://lkml.kernel.org/r/20170105125130.2815-1-nicstange@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull KVM fixes from Radim Krčmář:
"MIPS:
- fix host kernel crashes when receiving a signal with 64-bit
userspace
- flush instruction cache on all vcpus after generating entry code
(both for stable)
x86:
- fix NULL dereference in MMU caused by SMM transitions (for stable)
- correct guest instruction pointer after emulating some VMX errors
- minor cleanup"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: remove duplicated declaration
KVM: MIPS: Flush KVM entry code from icache globally
KVM: MIPS: Don't clobber CP0_Status.UX
KVM: x86: reset MMU on KVM_SET_VCPU_EVENTS
KVM: nVMX: fix instruction skipping during emulated vm-entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- re-introduce the arm64 get_current() optimisation
- KERN_CONT fallout fix in show_pte()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: restore get_current() optimisation
arm64: mm: fix show_pte KERN_CONT fallout
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
|
|
The following commit:
8196dab4fc15 ("x86/cpu: Get rid of compute_unit_id")
... broke the initial strategy for Bulldozer-based cores' topology,
where we consider each thread of a compute unit a standalone core
and not a HT or SMT thread.
Revert to the firmware-supplied core_id numbering and do not make
them thread siblings as we don't consider them for such even if they
technically are, more or less.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # v4.6+
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8196dab4fc15 ("x86/cpu: Get rid of compute_unit_id")
Link: http://lkml.kernel.org/r/20170105092638.5247-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
|
|
Declaration of VMX_VPID_EXTENT_SUPPORTED_MASK occures twice in the code.
Probably, it was happened after unsuccessful merge.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Flush the KVM entry code from the icache on all CPUs, not just the one
that built the entry code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.16.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
On 64-bit kernels, MIPS KVM will clear CP0_Status.UX to prevent the
guest (running in user mode) from accessing the 64-bit memory segments.
However the previous value of CP0_Status.UX is never restored when
exiting from the guest.
If the user process uses 64-bit addressing (the n64 ABI) this can result
in address error exceptions from the kernel if it needs to deliver a
signal before returning to user mode, as the kernel will need to write a
sigframe to high user addresses on the user stack which are disallowed
by CP0_Status.UX=0.
This is fixed by explicitly setting SX and UX again when exiting from
the guest, and explicitly clearing those bits when returning to the
guest. Having the SX and UX bits set when handling guest exits (rather
than only when exiting to userland) will be helpful when we support VZ,
since we shouldn't need to directly read or write guest memory, so it
will be valid for cache management IPIs to access host user addresses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.8.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
