summaryrefslogtreecommitdiffstats
path: root/arch
AgeCommit message (Collapse)AuthorFilesLines
2014-02-27ARM: OMAP3: Fix pinctrl interrupts for core2Tony Lindgren1-0/+1
After splitting padconf core into two parts to avoid exposing unaccessable registers, the new padconf core2 domain was left without a wake-up interrupt. Fix the issue by passing the shared wake-up interrupt in platform data like we do for padconf core and wkup domains already. Fixes: 3d49538364 (ARM: dts: Split omap3 pinmux core device) Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-21ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMPSantosh Shilimkar1-3/+5
for non SMP build, NR_CPUS is 1 and hence the code complains with below warnings. arch/arm/mach-omap2/cpuidle44xx.c:207:8: warning: array subscript is above array bounds [-Warray-bounds] arch/arm/mach-omap2/cpuidle44xx.c:212:11: warning: array subscript is above array bounds [-Warray-bounds] Kill it by making array size fixed. Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-21ARM: OMAP2+: Add support for thumb mode on DT booted N900Sebastian Reichel1-1/+19
Without enabling the workaround for ARM errata 430973 thumb compiled userland crashes randomly on the Nokia N900. Signed-off-by: Sebastian Reichel <sre@debian.org> Reviewed-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-21Merge tag 'for-v3.14-rc/omap-fixes-a' of ↵Tony Lindgren5-31/+96
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.14/fixes Several OMAP clock/PM/device data fixes for v3.14-rc. There's an OMAP5 reboot fix in there, plus a clock fix for rate computations involving x2 multipliers. Basic build, boot, and PM test logs are available here: http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/ Note that most full-chip PM is broken since the v3.14 merge; it's not caused by this series.
2014-02-19ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENTTomi Valkeinen2-15/+79
If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling clk_set_rate() on the clock "skips" the x2 multiplier as there are no set_rate and round_rate functions defined for the clkoutx2. This results in getting double the requested clock rates, breaking the display on omap3430 based devices. This got broken when d0f58bd3bba3877fb1af4664c4e33273d36f00e4 and related patches were merged for v3.14, as omapdss driver now relies more on the clk-framework and CLK_SET_RATE_PARENT. This patch implements set_rate and round_rate for clkoutx2. Tested on OMAP3430, OMAP3630, OMAP4460. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-02-19ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4Illia Smyrnov1-9/+11
Commit 313a76e (ARM: OMAP2+: hwmod: Fix SOFTRESET logic) introduced softreset bit cleaning right after set one. It is caused L3 error for OMAP4 ISS because ISS register write occurs when ISS reset process is in progress. Avoid this situation by cleaning softreset bit later, when reset process is successfully finished. Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-02-19ARM: DRA7: hwmod data: correct the sysc data for spinlockSuman Anna1-5/+4
The spinlock module's SYSCONFIG register on DRA7xx does not support smart wakeup, and also does not have the CLKACTIVITY field. The sysc data for spinlock module has been appropriately fixed up to reflect the same. Cc: Ambresh K <ambresh@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-02-19ARM: OMAP5: PRM: Fix reboot handlingVaibhav Bedia1-2/+2
Use the correct register offset for issuing the reset command in OMAP5. Since dev_inst is set dynamically OMAP4 should not be affected by this change. Signed-off-by: Vaibhav Bedia <vaibhav.bedia@gmail.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-02-13ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/TobiFlorian Vaussard4-7/+46
Unfortunatly the device tree for older OMAP35xx Overo cannot be used with newer OMAP36xx and vice-versa. To address this issue, move most of the Tobi DTS to a common include file, and create model-specific Tobi DTS. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Tested-by: Kevin Hilman <khilman@linaro.org> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: omap3-tobi: Use the correct vendor prefixFlorian Vaussard1-1/+1
Gumstix is the correct vendor for all Overo related products. Reported-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based OveroFlorian Vaussard2-4/+4
Tobi expansion board can be used with both OMAP35xx-based Overo, and OMAP36xx-based Overo. Currently the boot is broken with newer OMAP36xx-based Overo (Storm and alike). Fix include file and compatible string to be able to boot newer models. This will break older models. This will be addressed later. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Tested-by: Kevin Hilman <khilman@linaro.org> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP2+: Remove legacy macros for zoom platformsPaul Bolle1-9/+0
Commit 97411608fd5f ("ARM: OMAP2+: Remove legacy support for zoom platforms") removed the Kconfig symbols MACH_OMAP_ZOOM2 and MACH_OMAP_ZOOM3. Remove the last usage of the related macros too. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP2+: Remove MACH_NOKIA_N800Paul Bolle1-4/+0
The last caller of machine_is_nokia_n800() was removed in commit 5a87cde490e1 ("ARM: OMAP2+: Remove legacy booting support for n8x0"). That means that the Kconfig symbol MACH_NOKIA_N800 is now unused. It can safely be removed. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: N900: add missing compatible propertyAaro Koskinen1-2/+2
Add missing compatible property to avoid problems in the future. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: N9/N950: fix boot hang with 3.14-rc1Aaro Koskinen2-2/+2
N9/N950 does not boot anymore with 3.14-rc1, because SoC compatible property is missing. Fix that. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP1: nokia770: enable tahvo-usbAaro Koskinen1-0/+1
Add platform data for tahvo-usb. This is the last missing piece to get Tahvo USB working with 3.14. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND ↵Pekon Gupta1-1/+1
is built as module Fixes: commit 75d3625e0e86b2d8d77b4e9c6f685fd7ea0d5a96 ARM: OMAP2+: gpmc: add DT bindings for OneNAND OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and register them platform_device for ONENAND driver to probe later. However this does not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m). Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable to find any matching platform_device and remain un-binded. This causes on board ONENAND flash to remain un-detected. This patch causes GPMC controller to parse DT nodes when CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m CC: <stable@vger.kernel.org> # 3.9.x+ Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is ↵Pekon Gupta1-1/+1
built as module Fixes: commit bc6b1e7b86f5d8e4a6fc1c0189e64bba4077efe0 ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and register them platform_device for NAND driver to probe later. However this does not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m). Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable to find any matching platform_device and remain un-binded. This causes on board NAND flash to remain un-detected. This patch causes GPMC controller to parse DT nodes when CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m CC: <stable@vger.kernel.org> # 3.9.x+ Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: omap3-gta04: Fix mmc1 properties.Marek Belisko1-1/+1
Does not have an aux supply, and must be non-removable. Otherwise it is removed during suspend and filesystem gets confused. Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.NeilBrown1-1/+1
It should be ACTIVE_HIGH. Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: OMAP2+: add missing ARCH_HAS_OPPNishanth Menon1-0/+4
OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC only configuration boot to work with OPP. Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: am335x-evmsk: Fix mmc1 supportPeter Ujfalusi1-0/+9
Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not working on EVM-SK board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: DTS: am335x-evmsk: Correct audio clock frequencyPeter Ujfalusi1-1/+1
The clock for audio is sourced from virt_24000000_ck, so the correct frequency is 24000000. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-13ARM: dts: omap3-gta04: Add EOC irq gpio line handling.Marek Belisko1-0/+2
BMP085 EOC (End Of Conversion) irq line is connected to gpio113 on gta04. Set irq properties to have driver using irq instead polling for EOC. Signed-off-by: Marek Belisko <marek@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-02-02parisc: add flexible mmap memory layout supportHelge Deller6-43/+233
Add support for the flexible mmap memory layout (as described in http://lwn.net/Articles/91829). This is especially very interesting on parisc since we currently only support 32bit userspace (even with a 64bit Linux kernel). Signed-off-by: Helge Deller <deller@gmx.de>
2014-02-02parisc: Make EWOULDBLOCK be equal to EAGAIN on pariscGuy Martin1-1/+1
On Linux, only parisc uses a different value for EWOULDBLOCK which causes a lot of troubles for applications not checking for both values. Since the hpux compat is long dead, make EWOULDBLOCK behave the same as all other architectures. Signed-off-by: Guy Martin <gmsoft@tuxicoman.be> Signed-off-by: Helge Deller <deller@gmx.de>
2014-02-02parisc: convert uapi/asm/stat.h to use native types onlyHelge Deller1-21/+19
The stat.h header file is exported to userspace. Some userspace applications failed to compile due to missing/unknown types, so we better convert it to use native types only (like it's done on other architectures too). Signed-off-by: Helge Deller <deller@gmx.de>
2014-02-02parisc: wire up sched_setattr and sched_getattrHelge Deller2-1/+5
Signed-off-by: Helge Deller <deller@gmx.de>
2014-02-02parisc: fix cache-flushingHelge Deller3-3/+16
This commit: f8dae00684d678afa13041ef170cecfd1297ed40: parisc: Ensure full cache coherency for kmap/kunmap caused negative caching side-effects, e.g. hanging processes with expect and too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems. This patch now partly reverts it and has been in production use on our debian buildd makeservers since a week without any major problems. Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Helge Deller <deller@gmx.de>
2014-02-02Merge tag 'fixes-for-linus' of ↵Linus Torvalds27-43/+381
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "Here's a set of patches for (hopefully) -rc1. Some of them are fixes, but a good number of them also do things such as enable new drivers in the defconfigs for platforms that have such devices, increases coverage of the multiplatform defconfig and some DTS changes that plumbs up some of the devices that now have bindings and driver support. The commit dates are recent; we've mostly collected these fixes in the last few days but I also had to rebuild the branch yesterday to sort out some internal conflicts which reset the timestamps. The changes should have been tested by each platform maintainer already (and few of them have cross-platform impact) so I'm personally not too concerned by it at this time" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits) ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA ARM: multi_v7_defconfig: add mvebu drivers clocksource: kona: Add basic use of external clock drivers: bus: fix CCI driver kcalloc call parameters swap ARM: dts: bcm28155-ap: Fix Card Detection GPIO ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers ARM: dts: zynq: Add SDHCI nodes ARM: hisi: don't select SMP ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS ARM: multi_v7: copy most options from tegra_defconfig ARM: iop32x: fix power off handling for the EM7210 board ARM: integrator: restore static map on the CP ARM: msm_defconfig: Enable MSM clock drivers ARM: dts: msm: Add clock controller nodes and hook into uart ARM: OMAP4+: move errata initialization to omap4_pm_init_early ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP) ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference ...
2014-02-01tile: remove compat_sys_lookup_dcookie declaration to fix compile errorHeiko Carstens1-1/+0
With commit d8d14bd09cdd ("fs/compat: fix lookup_dcookie() parameter handling") I changed the type of the len parameter of the lookup_dcookie() syscall. However I missed that there was still a stale declaration in arch/tile/.. which now causes a compile error on tile: In file included from fs/dcookies.c:28:0: include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie' fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie' Simply remove the declaration in the tile architecture, which is only a leftover from before the different compat lookup_dcookie() versions have been merged. The correct declaration is now in include/linux/compat.h The build error was reported by Fenguang's build bot. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-01-31ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMAOlof Johansson1-10/+2
TI_EDMA fell out of automatically selected options in the multi_v7 defconfig due to a select being removed from the davinci Kconfig entry. So we need to re-enable explicitly to not regress some platforms. The rest is just the result of running 'make multi_v7_defconfig + make savedefconfig' to remove entries that are no longer needed due to changed dependencies/selects or defaults. Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: multi_v7_defconfig: add mvebu driversOlof Johansson1-0/+10
Recent boot farm testing has highlighted some issues with mvebu and multiplatform kernels. Increase the test coverage so we can discover these issues earlier. Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: dts: bcm28155-ap: Fix Card Detection GPIOTim Kryger1-1/+3
The board schematic states that the "SD_CARD_DET_N gets pulled to GND when card is inserted" so the polarity has been updated to active low. Polarity is now specified with a GPIO define instead of a magic number. Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31Merge tag 'renesas-dt-fixes2-for-v3.14' of ↵Olof Johansson1-4/+4
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes Second Round of Renesas ARM Based SoC DT Fixes for v3.14 Correct i2c clock references for r8a7790 (R-Car H2) SoC The error was introduced in 72197ca7a1cb1cea5 ("ARM: shmobile: r8a7790: Reference clocks") which is queued up for v3.14. * tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHYFabio Estevam1-0/+1
Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not setGrygorii Strashko2-1/+1
Drop automatic selection of TI_EDMA from Keystone Kconfig file, as it produces build warning in case if CONFIG_DMADEVICES is not set: warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE)) Instead enable TI EDMA support from defconfig. Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31Merge tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson3-3/+50
mvebu fixes for v3.13 (incremental #2) - allow building and booting DT and non-DT plat-orion SoCs - catch proper return value for kirkwood_pm_init() - properly check return of of_iomap to solve boot hangs (mirabox, others) - remove a compile warning on Armada 370 with non-SMP. * tag 'mvebu-fixes-3.13-2' of git://git.infradead.org/linux-mvebu: ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP) ARM: mvebu: Fix kernel hang in mvebu_soc_id_init() when of_iomap failed ARM: kirkwood: kirkwood_pm_init() should return void ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: dts: zynq: Add SDHCI nodesSoren Brinkmann4-0/+32
Add nodes for the Arasan SDHCI controller to Zynq dts files. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: hisi: don't select SMPRob Herring1-1/+0
SMP is a user configurable option, not a hardware feature and should not be selected. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: tegra: rebuild tegra_defconfig to add DEBUG_FSStephen Warren1-8/+3
DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled by tegra_defconfig. However, this config option no longer exists, so no longer selects DEBUG_FS, and nothing else selects it either. So, "make tegra_defconfig" no longer enables DEBUG_FS in .config. Rebuild tegra_defconfig on top of next-20140424, while manually re-enabling DEBUG_FS. Reasons for removed entries are: - I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT - DRM_PANEL: selected by DRM_TEGRA - NEW_LEDS: selected by many things; at least VT - LEDS_CLASS: selected by many things; at least VT - LEDS_TRIGGERS: selected by many things; at least VT - COMMON_CLK_DEBUG: no longer exists Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
2014-01-31ARM: multi_v7: copy most options from tegra_defconfigStephen Warren1-11/+142
multi_v7_defconfig was missing a large number of options that were in tegra_defconfig. This patch adds them. The changes fall into the following categories: * Enable more Tegra SoC options/drivers. * Enable more drivers for Tegra boards. * Enable more options that are useful for running distros. The patch removes a few lines as well, simply because those options are now selected by something else, and "make savedefconfig" removes them. I verified that the options appear in .config after "make multi_v7_defconfig". Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: iop32x: fix power off handling for the EM7210 boardLinus Walleij1-5/+27
This board was missed when converting all the others to proper abstracted GPIO handling. Fix it up the right way by requesting and driving GPIO line 0 high through gpiolib to power off the machine. Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: integrator: restore static map on the CPLinus Walleij1-0/+6
Commit 78d1632183454dba46ca8295484a5e7603acdc18 deleted the static mappings of the core modules, but this static map is still needed on the Integrator/CP (not the Integrator/AP). Restore the static map on the Integrator/CP. Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: msm_defconfig: Enable MSM clock driversStephen Boyd1-0/+4
This allows us to probe the clock controller devices and boot to a serial console on all DT enabled MSM platforms. Cc: David Brown <davidb@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: dts: msm: Add clock controller nodes and hook into uartStephen Boyd3-0/+53
Add the necessary DT nodes to probe the clock controllers on MSM devices as well as hook up the uart nodes to the clock controllers. This should allow us to boot to a serial console on all DT enabled MSM platforms. Cc: David Brown <davidb@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: OMAP4+: move errata initialization to omap4_pm_init_earlyNishanth Menon4-5/+23
Move all OMAP4 PM errata initializations to centralized location in omap4_pm_init_early. This allows for users to utilize the erratas in various submodules as needed. Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidleStrashko, Grygorii4-5/+31
The same workaround as ff999b8a0983ee15668394ed49e38d3568fc6859 "ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..." need to be applied not only when system is booting, but when MPUSS hits OSWR state through CPUIdle too. Without this WA the same issue is reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460 when CONFIG_CPU_IDLE is enabled. After MPUSS has enterred OSWR and waken up: - GIC distributor became disabled forever - scheduling is not performed any more Cc: Kevin Hilman <khilman@linaro.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-31Merge tag 'arm64-upstream' of ↵Linus Torvalds8-43/+74
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pyll ARM64 patches from Catalin Marinas: - Build fix with DMA_CMA enabled - Introduction of PTE_WRITE to distinguish between writable but clean and truly read-only pages - FIQs enabling/disabling clean-up (they aren't used on arm64) - CPU resume fix for the per-cpu offset restoring - Code comment typos * tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mm: Introduce PTE_WRITE arm64: mm: Remove PTE_BIT_FUNC macro arm64: FIQs are unused arm64: mm: fix the function name in comment of cpu_do_switch_mm arm64: fix build error if DMA_CMA is enabled arm64: kernel: fix per-cpu offset restore on resume arm64: mm: fix the function name in comment of __flush_dcache_area arm64: mm: use ubfm for dcache_line_size
2014-01-31Merge branch 'for-linus' of ↵Linus Torvalds8-3/+87
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha Pull alpha updates from Matt Turner: "A pair of changes for alpha. One fixes a networking regression, and the second adds audit syscall support which will help in supporting systemd" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha: alpha: fix broken network checksum alpha: Enable system-call auditing support.
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-03 19:20:36 +0000