| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (92 commits)
powerpc: Remove unused 'protect4gb' boot parameter
powerpc: Build-in e1000e for pseries & ppc64_defconfig
powerpc/pseries: Make request_ras_irqs() available to other pseries code
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
powerpc: Use smt_snooze_delay=-1 to always busy loop
powerpc: Remove check of ibm,smt-snooze-delay OF property
powerpc/kdump: Fix race in kdump shutdown
powerpc/kexec: Fix race in kexec shutdown
powerpc/kexec: Speedup kexec hash PTE tear down
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
powerpc: Use more accurate limit for first segment memory allocations
powerpc/kdump: Use chip->shutdown to disable IRQs
powerpc/kdump: CPUs assume the context of the oopsing CPU
powerpc/crashdump: Do not fail on NULL pointer dereferencing
powerpc/eeh: Fix oops when probing in early boot
powerpc/pci: Check devices status property when scanning OF tree
powerpc/vio: Switch VIO Bus PM to use generic helpers
powerpc: Avoid bad relocations in iSeries code
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'dbg-early-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
echi-dbgp: Add kernel debugger support for the usb debug port
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
kgdboc: Add ekgdboc for early use of the kernel debugger
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
x86,kgdb: Implement early hardware breakpoint debugging
x86, kgdb, init: Add early and late debug states
x86, kgdb: early trap init for early debug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
|
|
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
|
|
'protect4gb' boot parameter was introduced to avoid allocating dma
space acrossing 4GB boundary in 2007 (the commit
569975591c5530fdc9c7a3c45122e5e46f075a74).
In 2008, the IOMMU was fixed to use the boundary_mask parameter per
device properly. So 'protect4gb' workaround was removed (the
383af9525bb27f927511874f6306247ec13f1c28). But somehow I messed the
'protect4gb' boot parameter that was used to enable the
workaround.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The e1000e device is becoming more common these days, so let's just
build it in for pseries & ppc64_defconfig.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
At the moment only the RAS code uses event-sources interrupts (for EPOW
events and internal errors) so request_ras_irqs() (which actually requests
the event-sources interrupts) is found in ras.c and is static.
We want to be able to use event-sources interrupts in other pseries code,
so let's rename request_ras_irqs() to request_event_sources_irqs() and
move it to event_sources.c.
This will be used in an upcoming patch that adds support for IO Event
interrupts that come through as event sources.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I've been told that the architected way to determine we are in form 1
affinity mode is by reading the ibm,architecture-vec-5 property which
mirrors the layout of the fifth vector of the ibm,client-architecture
structure.
Eventually we may want to parse the ibm,architecture-vec-5 and create
FW_FEATURE_* bits.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I noticed /proc/sys/vm/zone_reclaim_mode was 0 on a ppc64 NUMA box. It gets
enabled via this:
/*
* If another node is sufficiently far away then it is better
* to reclaim pages in a zone before going off node.
*/
if (distance > RECLAIM_DISTANCE)
zone_reclaim_mode = 1;
Since we use the default value of 20 for REMOTE_DISTANCE and 20 for
RECLAIM_DISTANCE it never kicks in.
The local to remote bandwidth ratios can be quite large on System p
machines so it makes sense for us to reclaim clean pagecache locally before
going off node.
The patch below sets a smaller value for RECLAIM_DISTANCE and thus enables
zone reclaim.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Right now if we want to busy loop and not give up any time to the hypervisor
we put a very large value into smt_snooze_delay. This is sometimes useful
when running a single partition and you want to avoid any latencies due
to the hypervisor or CPU power state transitions. While this works, it's a bit
ugly - how big a number is enough now we have NO_HZ and can be idle for a very
long time.
The patch below makes smt_snooze_delay signed, and a negative value means loop
forever:
echo -1 > /sys/devices/system/cpu/cpu0/smt_snooze_delay
This change shouldn't affect the existing userspace tools (eg ppc64_cpu), but
I'm cc-ing Nathan just to be sure.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I'm not sure why we have code for parsing an ibm,smt-snooze-delay OF
property. Since we have a smt-snooze-delay= boot option and we can
also set it at runtime via sysfs, it should be safe to get rid of
this code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When we are crashing, the crashing/primary CPU IPIs the secondaries to
turn off IRQs, go into real mode and wait in kexec_wait. While this
is happening, the primary tears down all the MMU maps. Unfortunately
the primary doesn't check to make sure the secondaries have entered
real mode before doing this.
On PHYP machines, the secondaries can take a long time shutting down
the IRQ controller as RTAS calls are need. These RTAS calls need to
be serialised which resilts in the secondaries contending in
lock_rtas() and hence taking a long time to shut down.
We've hit this on large POWER7 machines, where some secondaries are
still waiting in lock_rtas(), when the primary tears down the HPTEs.
This patch makes sure all secondaries are in real mode before the
primary tears down the MMU. It uses the new kexec_state entry in the
paca. It times out if the secondaries don't reach real mode after
10sec.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In kexec_prepare_cpus, the primary CPU IPIs the secondary CPUs to
kexec_smp_down(). kexec_smp_down() calls kexec_smp_wait() which sets
the hw_cpu_id() to -1. The primary does this while leaving IRQs on
which means the primary can take a timer interrupt which can lead to
the IPIing one of the secondary CPUs (say, for a scheduler re-balance)
but since the secondary CPU now has a hw_cpu_id = -1, we IPI CPU
-1... Kaboom!
We are hitting this case regularly on POWER7 machines.
There is also a second race, where the primary will tear down the MMU
mappings before knowing the secondaries have entered real mode.
Also, the secondaries are clearing out any pending IPIs before
guaranteeing that no more will be received.
This changes kexec_prepare_cpus() so that we turn off IRQs in the
primary CPU much earlier. It adds a paca flag to say that the
secondaries have entered the kexec_smp_down() IPI and turned off IRQs,
rather than overloading hw_cpu_id with -1. This new paca flag is
again used to in indicate when the secondaries has entered real mode.
It also ensures that all CPUs have their IRQs off before we clear out
any pending IPI requests (in kexec_cpu_down()) to ensure there are no
trailing IPIs left unacknowledged.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently for kexec the PTE tear down on 1TB segment systems normally
requires 3 hcalls for each PTE removal. On a machine with 32GB of
memory it can take around a minute to remove all the PTEs.
This optimises the path so that we only remove PTEs that are valid.
It also uses the read 4 PTEs at once HCALL. For the common case where
a PTEs is invalid in a 1TB segment, this turns the 3 HCALLs per PTE
down to 1 HCALL per 4 PTEs.
This gives an > 10x speedup in kexec times on PHYP, taking a 32GB
machine from around 1 minute down to a few seconds.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds plpar_pte_read_4_raw() which can be used read 4 PTEs from
PHYP at a time, while in real mode.
It also creates a new hcall9 which can be used in real mode. It's the
same as plpar_hcall9 but minus the tracing hcall statistics which may
require variables outside the RMO.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Author: Milton Miller <miltonm@bga.com>
On large machines we are running out of room below 256MB. In some cases we
only need to ensure the allocation is in the first segment, which may be
256MB or 1TB.
Add slb0_limit and use it to specify the upper limit for the irqstack and
emergency stacks.
On a large ppc64 box, this fixes a panic at boot when the crashkernel=
option is specified (previously we would run out of memory below 256MB).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I saw this in a kdump kernel:
IOMMU table initialized, virtual merging enabled
Interrupt 155954 (real) is invalid, disabling it.
Interrupt 155953 (real) is invalid, disabling it.
ie we took some spurious interrupts. default_machine_crash_shutdown tries
to disable all interrupt sources but uses chip->disable which maps to
the default action of:
static void default_disable(unsigned int irq)
{
}
If we use chip->shutdown, then we actually mask the IRQ:
static void default_shutdown(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
desc->chip->mask(irq);
desc->status |= IRQ_MASKED;
}
Not sure why we don't implement a ->disable action for xics.c, or why
default_disable doesn't mask the interrupt.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We wrap the crash_shutdown_handles[] calls with longjmp/setjmp, so if any
of them fault we can recover. The problem is we add a hook to the debugger
fault handler hook which calls longjmp unconditionally.
This first part of kdump is run before we marshall the other CPUs, so there
is a very good chance some CPU on the box is going to page fault. And when
it does it hits the longjmp code and assumes the context of the oopsing CPU.
The machine gets very confused when it has 10 CPUs all with the same stack,
all thinking they have the same CPU id. I get even more confused trying
to debug it.
The patch below adds crash_shutdown_cpu and uses it to specify which cpu is
in the protected region. Since it can only be -1 or the oopsing CPU, we don't
need to use memory barriers since it is only valid on the local CPU - no other
CPU will ever see a value that matches it's local CPU id.
Eventually we should switch the order and marshall all CPUs before doing the
crash_shutdown_handles[] calls, but that is a bigger fix.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Maxim Uvarov <muvarov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we take an EEH error early enough, we oops:
Call Trace:
[c000000010483770] [c000000000013ee4] .show_stack+0xd8/0x218 (unreliable)
[c000000010483850] [c000000000658940] .dump_stack+0x28/0x3c
[c0000000104838d0] [c000000000057a68] .eeh_dn_check_failure+0x2b8/0x304
[c000000010483990] [c0000000000259c8] .rtas_read_config+0x120/0x168
[c000000010483a40] [c000000000025af4] .rtas_pci_read_config+0xe4/0x124
[c000000010483af0] [c00000000037af18] .pci_bus_read_config_word+0xac/0x104
[c000000010483bc0] [c0000000008fec98] .pcibios_allocate_resources+0x7c/0x220
[c000000010483c90] [c0000000008feed8] .pcibios_resource_survey+0x9c/0x418
[c000000010483d80] [c0000000008fea10] .pcibios_init+0xbc/0xf4
[c000000010483e20] [c000000000009844] .do_one_initcall+0x98/0x1d8
[c000000010483ed0] [c0000000008f0560] .kernel_init+0x228/0x2e8
[c000000010483f90] [c000000000031a08] .kernel_thread+0x54/0x70
EEH: Detected PCI bus error on device <null>
EEH: This PCI device has failed 1 times in the last hour:
EEH: location=U78A5.001.WIH8464-P1 driver= pci addr=0001:00:01.0
EEH: of node=/pci@800000020000209/usb@1
EEH: PCI device/vendor: 00351033
EEH: PCI cmd/status register: 12100146
Unable to handle kernel paging request for data at address 0x00000468
Oops: Kernel access of bad area, sig: 11 [#1]
....
NIP [c000000000057610] .rtas_set_slot_reset+0x38/0x10c
LR [c000000000058724] .eeh_reset_device+0x5c/0x124
Call Trace:
[c00000000bc6bd00] [c00000000005a0e0] .pcibios_remove_pci_devices+0x7c/0xb0 (unreliable)
[c00000000bc6bd90] [c000000000058724] .eeh_reset_device+0x5c/0x124
[c00000000bc6be40] [c0000000000589c0] .handle_eeh_events+0x1d4/0x39c
[c00000000bc6bf00] [c000000000059124] .eeh_event_handler+0xf0/0x188
[c00000000bc6bf90] [c000000000031a08] .kernel_thread+0x54/0x70
We called rtas_set_slot_reset while scanning the bus and before the pci_dn
to pcidev mapping has been created. Since we only need the pcidev to work
out the type of reset and that only gets set after the module for the
device loads, lets just do a hot reset if the pcidev is NULL.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.
However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.
Signed-of-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Switch to use the generic power management helpers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Subrata Modak reported that building a CONFIG_RELOCATABLE kernel with
CONFIG_ISERIES enabled gives the following warnings:
WARNING: 4 bad relocations
c00000000007216e R_PPC64_ADDR16_HIGHEST __ksymtab+0x00000000009dcec8
c000000000072172 R_PPC64_ADDR16_HIGHER __ksymtab+0x00000000009dcec8
c00000000007217a R_PPC64_ADDR16_HI __ksymtab+0x00000000009dcec8
c00000000007217e R_PPC64_ADDR16_LO __ksymtab+0x00000000009dcec8
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd314ef95553604208c25bc35581f7f0a
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
|
|
Allow kdb to work properly with with earlyprintk=vga by interpreting
the backspace and carriage return output characters. These
interpretation of these characters is used for simple line editing
provided in the kdb shell.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
If the kernel debugger was configured, attached and started with
kgdbwait, the hardware breakpoint registers should get restored by the
kgdb code which is managing the dr registers.
CC: x86@kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
It is not possible to use the hw_breakpoint.c API prior to mm_init(),
but it is possible to use hardware breakpoints with the kernel
debugger.
Prior to smp_init() it is possible to simply write to the dr registers
of the boot cpu directly. This can be used up until the
kgdb_arch_late() is invoked, at which point the standard hw_breakpoint.c
API will get used.
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
The kernel debugger can operate well before mm_init(), but the x86
hardware breakpoint code which uses the perf api requires that the
kernel allocators are initialized.
This means the kernel debug core needs to provide an optional arch
specific call back to allow the initialization functions to run after
the kernel has been further initialized.
The kdb shell already had a similar restriction with an early
initialization and late initialization. The kdb_init() was moved into
the debug core's version of the late init which is called
dbg_late_init();
CC: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Allow the x86 arch to have early exception processing for the purpose
of debugging via the kgdb.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to have a low level "first opportunity handler" do_trap_or_bp() handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Also added was a die notification for oops such that kdb can catch an
oops for analysis.
There appeared to be no obvious way to pass the struct pt_regs from
the original exception back to the stack back tracer, so a special
case was added to show_stack() for when kdb is active because you
generally desire to generally look at the back trace of the original
exception.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to allow the kernel debugger to handle the exception first in
program_check_exception().
The other change here is to make sure that kgdb_handle_exception() is
called with correct parameters when catching an oops, because kdb
needs to know if the entry was an oops, single step, or breakpoint
exception.
[benh@kernel.crashing.org: move debugger_bpt instead of #ifdef]
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a triple fault is
to have a low level "first opportunity handler" in the int3 exception
handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
Remove all the references to the kgdb_post_primary_code. This
function serves no useful purpose because you can obtain the same
information from the "struct kgdb_state *ks" from with in the
debugger, if for some reason you want the data.
Also remove the unintentional duplicate assignment for ks->ex_vector.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
|
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
|
|
This patch contains the hooks and instrumentation into kernel which
live outside the kernel/debug directory, which the kdb core
will call to run commands like lsmod, dmesg, bt etc...
CC: linux-arch@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
|
|
The new debug core api requires all architectures that use to debug
core to implement a function to set the program counter.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Implement kgdb_arch_pc() which adjusts the pc if it needs to be
adjusted after a software breakpoint trap.
Implement kgdb_arch_set_pc() which is a new required function in the
kgdb debug core.
When processing a single step return zero in the error exception field
so that the debug core can distinguish between a single step trap and
a breakpoint trap generically.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
|
|
The new debug core api requires all architectures that use to debug
core to implement a function to set the program counter.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Add platform init code for the OMAP3 OHCI driver.
Also, configure padconf settings for OMAP3 depending
on which port mode is used.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
Add support for i2c init for omap4.
This patch is based on and earlier patch by
Santosh Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add separate omap_i2c_add_bus functions for mach-omap1
and mach-omap2. Make the mach-omap2 init set the interrupt
dynamically to support.
This is needed to add support for omap4 in a way that
works with multi-omap builds. This will eventually get
fixed in a generic way with the omap hwmods.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
