| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On 32 bit systems cmpxchg cannot handle 64 bit values, so
some additional magic is required to allow a 32 bit system
with CONFIG_VIRT_CPU_ACCOUNTING_GEN=y enabled to build.
Make sure the correct cmpxchg function is used when doing
an atomic swap of a cputime_t.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Cc: oleg@redhat.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux390@de.ibm.com
Cc: linux-arch@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20140930155947.070cdb1f@annuminas.surriel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
cebf15eb09a2 ("x86, sched: Add new topology for multi-NUMA-node CPUs")
some code to try to detect the situation where we have a NUMA node
inside of the "DIE" sched domain.
It detected this by looking for cpus which match_die() but do not match
NUMA nodes via topology_same_node().
I wrote it up as:
if (match_die(c, o) == !topology_same_node(c, o))
which actually seemed to work some of the time, albiet
accidentally.
It should have been doing an &&, not an ==.
This code essentially chopped off the "DIE" domain on one of
Andrew Morton's systems. He reported that this patch fixed his
issue.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Link: http://lkml.kernel.org/r/20140930214546.FD481CFF@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I'm getting the spew below when booting with Haswell (Xeon
E5-2699 v3) CPUs and the "Cluster-on-Die" (CoD) feature enabled
in the BIOS. It seems similar to the issue that some folks from
AMD ran in to on their systems and addressed in this commit:
161270fc1f9d ("x86/smp: Fix topology checks on AMD MCM CPUs")
Both these Intel and AMD systems break an assumption which is
being enforced by topology_sane(): a socket may not contain more
than one NUMA node.
AMD special-cased their system by looking for a cpuid flag. The
Intel mode is dependent on BIOS options and I do not know of a
way which it is enumerated other than the tables being parsed
during the CPU bringup process. In other words, we have to trust
the ACPI tables <shudder>.
This detects the situation where a NUMA node occurs at a place in
the middle of the "CPU" sched domains. It replaces the default
topology with one that relies on the NUMA information from the
firmware (SRAT table) for all levels of sched domains above the
hyperthreads.
This also fixes a sysfs bug. We used to freak out when we saw
the "mc" group cross a node boundary, so we stopped building the
MC group. MC gets exported as the 'core_siblings_list' in
/sys/devices/system/cpu/cpu*/topology/ and this caused CPUs with
the same 'physical_package_id' to not be listed together in
'core_siblings_list'. This violates a statement from
Documentation/ABI/testing/sysfs-devices-system-cpu:
core_siblings: internal kernel map of cpu#'s hardware threads
within the same physical_package_id.
core_siblings_list: human-readable list of the logical CPU
numbers within the same physical_package_id as cpu#.
The sysfs effects here cause an issue with the hwloc tool where
it gets confused and thinks there are more sockets than are
physically present.
Before this patch, there are two packages:
# cd /sys/devices/system/cpu/
# cat cpu*/topology/physical_package_id | sort | uniq -c
18 0
18 1
But 4 _sets_ of core siblings:
# cat cpu*/topology/core_siblings_list | sort | uniq -c
9 0-8
9 18-26
9 27-35
9 9-17
After this set, there are only 2 sets of core siblings, which
is what we expect for a 2-socket system.
# cat cpu*/topology/physical_package_id | sort | uniq -c
18 0
18 1
# cat cpu*/topology/core_siblings_list | sort | uniq -c
18 0-17
18 18-35
Example spew:
...
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
#2 #3 #4 #5 #6 #7 #8
.... node #1, CPUs: #9
------------[ cut here ]------------
WARNING: CPU: 9 PID: 0 at /home/ak/hle/linux-hle-2.6/arch/x86/kernel/smpboot.c:306 topology_sane.isra.2+0x74/0x90()
sched: CPU #9's mc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
Modules linked in:
CPU: 9 PID: 0 Comm: swapper/9 Not tainted 3.17.0-rc1-00293-g8e01c4d-dirty #631
Hardware name: Intel Corporation S2600WTT/S2600WTT, BIOS GRNDSDP1.86B.0036.R05.1407140519 07/14/2014
0000000000000009 ffff88046ddabe00 ffffffff8172e485 ffff88046ddabe48
ffff88046ddabe38 ffffffff8109691d 000000000000b001 0000000000000009
ffff88086fc12580 000000000000b020 0000000000000009 ffff88046ddabe98
Call Trace:
[<ffffffff8172e485>] dump_stack+0x45/0x56
[<ffffffff8109691d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8109698c>] warn_slowpath_fmt+0x4c/0x50
[<ffffffff81074f94>] topology_sane.isra.2+0x74/0x90
[<ffffffff8107530e>] set_cpu_sibling_map+0x31e/0x4f0
[<ffffffff8107568d>] start_secondary+0x1ad/0x240
---[ end trace 3fe5f587a9fcde61 ]---
#10 #11 #12 #13 #14 #15 #16 #17
.... node #2, CPUs: #18 #19 #20 #21 #22 #23 #24 #25 #26
.... node #3, CPUs: #27 #28 #29 #30 #31 #32 #33 #34 #35
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
[ Added LLC domain and s/match_mc/match_die/ ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: brice.goglin@gmail.com
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/20140918193334.C065EBCE@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Kirill found that there's a subtle race in the
__ARCH_WANT_UNLOCKED_CTXSW code, and instead of fixing it, remove the
entire exception because neither arch that uses it seems to actually
still require it.
Boot tested on mips64el (qemu) only.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kirill Tkhai <tkhai@yandex.ru>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: oleg@redhat.com
Cc: linux@roeck-us.net
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20140923150641.GH3312@worktop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the new arch_scale_cpu_capacity() scheduler facility in order to reflect
the original capacity of a CPU instead of arch_scale_freq_capacity() which is
more linked to a scaling of the capacity linked to the frequency.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: preeti@linux.vnet.ibm.com
Cc: riel@redhat.com
Cc: Morten.Rasmussen@arm.com
Cc: efault@gmx.de
Cc: daniel.lezcano@linaro.org
Cc: dietmar.eggemann@arm.com
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1409051215-16788-6-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This facility is used in a few places so let's introduce
a helper function to improve code readability.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: aneesh.kumar@linux.vnet.ibm.com
Cc: dzickus@redhat.com
Cc: bmr@redhat.com
Cc: jcastillo@redhat.com
Cc: oleg@redhat.com
Cc: riel@redhat.com
Cc: prarit@redhat.com
Cc: jgh@redhat.com
Cc: minchan@kernel.org
Cc: mpe@ellerman.id.au
Cc: tglx@linutronix.de
Cc: hannes@cmpxchg.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1410527779-8133-3-git-send-email-atomlin@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Tasks get their end of stack set to STACK_END_MAGIC with the
aim to catch stack overruns. Currently this feature does not
apply to init_task. This patch removes this restriction.
Note that a similar patch was posted by Prarit Bhargava
some time ago but was never merged:
http://marc.info/?l=linux-kernel&m=127144305403241&w=2
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: aneesh.kumar@linux.vnet.ibm.com
Cc: dzickus@redhat.com
Cc: bmr@redhat.com
Cc: jcastillo@redhat.com
Cc: jgh@redhat.com
Cc: minchan@kernel.org
Cc: tglx@linutronix.de
Cc: hannes@cmpxchg.org
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Daeseok Youn <daeseok.youn@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1410527779-8133-2-git-send-email-atomlin@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
schedule()
schedule(), io_schedule() and schedule_timeout() always return
with TASK_RUNNING state set, so one more setting is unnecessary.
(All places in patch are visible good, only exception is
kiblnd_scheduler() from:
drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c
Its schedule() is one line above standard 3 lines of unified diff)
No places where set_current_state() is used for mb().
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1410529254.3569.23.camel@tkhai
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Anil Belur <askb23@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: David Howells <dhowells@redhat.com>
Cc: Dmitry Eremin <dmitry.eremin@intel.com>
Cc: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Isaac Huang <he.huang@intel.com>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Liang Zhen <liang.zhen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Masaru Nomura <massa.nomura@gmail.com>
Cc: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Oleg Drokin <green@linuxhacker.ru>
Cc: Peng Tao <bergwolf@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: devel@driverdev.osuosl.org
Cc: dm-devel@redhat.com
Cc: dri-devel@lists.freedesktop.org
Cc: fcoe-devel@open-fcoe.org
Cc: jfs-discussion@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-afs@lists.infradead.org
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-nfs@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: qla2xxx-upstream@qlogic.com
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: user-mode-linux-user@lists.sourceforge.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"Another round of fixes from arm-soc land, which are mostly DT fixes
for:
- OMAP: handful of DT fixes devices on newly supported hardware
- davinci: fix 2nd EDMA channel
- ux500: extend previous pinctrl fix to another board
- at91: clock registration fixes, compatibility string precision
And one more fix for event cleanup in drivers/bus/arm-ccn"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Move event cleanup routine
ARM: at91/dt: rm9200: fix usb clock definition
ARM: at91: rm9200: fix clock registration
ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
ARM: ux500: disable msp2 node on Snowball
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock
|
|
Merge "at91: fixes for 3.17 #1" from Nicols Ferre:
First AT91 fixes batch for 3.17:
- compatibility string precision
- clock registration and USB DT fix for at91rm9200
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: rm9200: fix usb clock definition
ARM: at91: rm9200: fix clock registration
ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Wire up new syscalls getrandom and memfd_create"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up memfd_create
m68k: Wire up getrandom
|
|
The atmel,clk-divisors property is taking 4 divisors, if less are
provided, the clock registration will fail.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Actually register clocks from device tree when using the common clock
framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: add at91 to function name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The at91sam9g20 SOC uses its own pllb implementation which is different
from the one inherited from at91sam9260 SOC.
Signed-off-by: Gaël PORTAY <gael.portay@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.17-rc3" from Tony Lindgren:
Few fixes for omaps mostly for various devices to get them working
properly on the new am437x and dra7 hardware for several devices
such as I2C, NAND, DDR3 and USB. There's also a clock fix for omap3.
And also included are two minor cosmetic fixes that are not
stictly fixes for the new hardware support added recently to
downgrade a GPMC warning into a debug statement, and fix the
confusing comments for dra7-evm spi1 mux.
Note that these are all .dts changes except for a GPMC change.
* tag 'omap-fixes-against-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (255 commits)
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
Linux 3.17-rc3
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This patch fixes setup of second EDMA channel controller
on DA850.
* tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
|
|
DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).
Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1daaf1af ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Size should be 64KiB instead of 92KiB.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
fixes-rc3
|
|
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Structure name and variable name were erroneously interchanged
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
[ Also removed pointless cast from "void *". - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- misc fixes (fpsimd context handling, crypto, ...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
|
|
fc95ca7284bc54953165cba76c3228bd2cdb9591 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Analogous to commit 8858d88a25142544843869f0cd3e6654aa7b4aec
that fixed commit 70b41abc151f9
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
|
|
commit 0944fe3f4a32 ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
|
|
Since 3.12 or more precisely commit 0944fe3f4a32 ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
|
|
It turns out that vendors are relying on the format of /proc/cpuinfo,
and we've even spotted out-of-tree hacks attempting to make it look
identical to the format used by arch/arm/. That means we can't afford to
churn this interface in mainline, so revert the recent reformatting of
the file for arm64 pending discussions on the list to find out what
people actually want.
This reverts commit d7a49086f263164a2c4c178eb76412d48cd671d7.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Now arm64 defers reloading FPSIMD state, but this optimization also
introduces the bug after cpu resume back from low power mode.
The reason is after the cpu has been powered off, s/w need set the
cpu's fpsimd_last_state to NULL so that it will force to reload
FPSIMD state for the thread, otherwise there has the chance to meet
the condition for both the task's fpsimd_state.cpu field contains the
id of the current cpu, and the cpu's fpsimd_last_state per-cpu variable
points to the task's fpsimd_state, so finally kernel will skip to reload
the context during it return back to userland.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
|
|
unicore32 builds fail with
arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
arch/unicore32/kernel/signal.c: In function ‘do_signal’:
arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
make: *** [arch/unicore32/kernel/signal.o] Error 2
Bisect points to commit 649671c90eaf ("unicore32: Use get_signal()
signal_setup_done()").
This code never even compiled. Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up. Compile
tested only.
Fixes: 649671c90eaf ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"Various assorted fixes:
- a couple of patches from Mark Rutland to resolve an errata with
Cortex-A15 CPUs.
- fix cpuidle for the CPU part ID changes in the last merge window
- add support for a relocation which ARM binutils is generating in
some circumstances"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
ARM: 8128/1: abort: don't clear the exclusive monitors
ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
|
|
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:
arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
struct ve_spc_opp *opps = info->opps[cluster];
^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:
Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
|
|
Merge patches from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
kexec: purgatory: add clean-up for purgatory directory
Documentation/kdump/kdump.txt: add ARM description
flush_icache_range: export symbol to fix build errors
tools: selftests: fix build issue with make kselftests target
ocfs2: quorum: add a log for node not fenced
ocfs2: o2net: set tcp user timeout to max value
ocfs2: o2net: don't shutdown connection when idle timeout
ocfs2: do not write error flag to user structure we cannot copy from/to
x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
xattr: fix check for simultaneous glibc header inclusion
kexec: remove CONFIG_KEXEC dependency on crypto
kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
x86,mm: fix pte_special versus pte_numa
hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
mm/zpool: use prefixed module loading
zram: fix incorrect stat with failed_reads
lib: turn CONFIG_STACKTRACE into an actual option.
mm: actually clear pmd_numa before invalidating
memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
...
|
|
Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
