Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull performance event updates from Ingo Molnar:
- Add CPU-PMU support for Intel Sapphire Rapids CPUs
- Extend the perf ABI with PERF_SAMPLE_WEIGHT_STRUCT, to offer
two-parameter sampling event feedback. Not used yet, but is intended
for Golden Cove CPU-PMU, which can provide both the instruction
latency and the cache latency information for memory profiling
events.
- Remove experimental, default-disabled perfmon-v4 counter_freezing
support that could only be enabled via a boot option. The hardware is
hopelessly broken, we'd like to make sure nobody starts relying on
this, as it would only end in tears.
- Fix energy/power events on Intel SPR platforms
- Simplify the uprobes resume_execution() logic
- Misc smaller fixes.
* tag 'perf-core-2021-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/rapl: Fix psys-energy event on Intel SPR platform
perf/x86/rapl: Only check lower 32bits for RAPL energy counters
perf/x86/rapl: Add msr mask support
perf/x86/kvm: Add Cascade Lake Xeon steppings to isolation_ucodes[]
perf/x86/intel: Support CPUID 10.ECX to disable fixed counters
perf/x86/intel: Add perf core PMU support for Sapphire Rapids
perf/x86/intel: Filter unsupported Topdown metrics event
perf/x86/intel: Factor out intel_update_topdown_event()
perf/core: Add PERF_SAMPLE_WEIGHT_STRUCT
perf/intel: Remove Perfmon-v4 counter_freezing support
x86/perf: Use static_call for x86_pmu.guest_get_msrs
perf/x86/intel/uncore: With > 8 nodes, get pci bus die id from NUMA info
perf/x86/intel/uncore: Store the logical die id instead of the physical die id.
x86/kprobes: Do not decode opcode in resume_execution()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"Core scheduler updates:
- Add CONFIG_PREEMPT_DYNAMIC: this in its current form adds the
preempt=none/voluntary/full boot options (default: full), to allow
distros to build a PREEMPT kernel but fall back to close to
PREEMPT_VOLUNTARY (or PREEMPT_NONE) runtime scheduling behavior via
a boot time selection.
There's also the /debug/sched_debug switch to do this runtime.
This feature is implemented via runtime patching (a new variant of
static calls).
The scope of the runtime patching can be best reviewed by looking
at the sched_dynamic_update() function in kernel/sched/core.c.
( Note that the dynamic none/voluntary mode isn't 100% identical,
for example preempt-RCU is available in all cases, plus the
preempt count is maintained in all models, which has runtime
overhead even with the code patching. )
The PREEMPT_VOLUNTARY/PREEMPT_NONE models, used by the vast
majority of distributions, are supposed to be unaffected.
- Fix ignored rescheduling after rcu_eqs_enter(). This is a bug that
was found via rcutorture triggering a hang. The bug is that
rcu_idle_enter() may wake up a NOCB kthread, but this happens after
the last generic need_resched() check. Some cpuidle drivers fix it
by chance but many others don't.
In true 2020 fashion the original bug fix has grown into a 5-patch
scheduler/RCU fix series plus another 16 RCU patches to address the
underlying issue of missed preemption events. These are the initial
fixes that should fix current incarnations of the bug.
- Clean up rbtree usage in the scheduler, by providing & using the
following consistent set of rbtree APIs:
partial-order; less() based:
- rb_add(): add a new entry to the rbtree
- rb_add_cached(): like rb_add(), but for a rb_root_cached
total-order; cmp() based:
- rb_find(): find an entry in an rbtree
- rb_find_add(): find an entry, and add if not found
- rb_find_first(): find the first (leftmost) matching entry
- rb_next_match(): continue from rb_find_first()
- rb_for_each(): iterate a sub-tree using the previous two
- Improve the SMP/NUMA load-balancer: scan for an idle sibling in a
single pass. This is a 4-commit series where each commit improves
one aspect of the idle sibling scan logic.
- Improve the cpufreq cooling driver by getting the effective CPU
utilization metrics from the scheduler
- Improve the fair scheduler's active load-balancing logic by
reducing the number of active LB attempts & lengthen the
load-balancing interval. This improves stress-ng mmapfork
performance.
- Fix CFS's estimated utilization (util_est) calculation bug that can
result in too high utilization values
Misc updates & fixes:
- Fix the HRTICK reprogramming & optimization feature
- Fix SCHED_SOFTIRQ raising race & warning in the CPU offlining code
- Reduce dl_add_task_root_domain() overhead
- Fix uprobes refcount bug
- Process pending softirqs in flush_smp_call_function_from_idle()
- Clean up task priority related defines, remove *USER_*PRIO and
USER_PRIO()
- Simplify the sched_init_numa() deduplication sort
- Documentation updates
- Fix EAS bug in update_misfit_status(), which degraded the quality
of energy-balancing
- Smaller cleanups"
* tag 'sched-core-2021-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
sched,x86: Allow !PREEMPT_DYNAMIC
entry/kvm: Explicitly flush pending rcuog wakeup before last rescheduling point
entry: Explicitly flush pending rcuog wakeup before last rescheduling point
rcu/nocb: Trigger self-IPI on late deferred wake up before user resume
rcu/nocb: Perform deferred wake up before last idle's need_resched() check
rcu: Pull deferred rcuog wake up to rcu_eqs_enter() callers
sched/features: Distinguish between NORMAL and DEADLINE hrtick
sched/features: Fix hrtick reprogramming
sched/deadline: Reduce rq lock contention in dl_add_task_root_domain()
uprobes: (Re)add missing get_uprobe() in __find_uprobe()
smp: Process pending softirqs in flush_smp_call_function_from_idle()
sched: Harden PREEMPT_DYNAMIC
static_call: Allow module use without exposing static_call_key
sched: Add /debug/sched_preempt
preempt/dynamic: Support dynamic preempt with preempt= boot option
preempt/dynamic: Provide irqentry_exit_cond_resched() static call
preempt/dynamic: Provide preempt_schedule[_notrace]() static calls
preempt/dynamic: Provide cond_resched() and might_resched() static calls
preempt: Introduce CONFIG_PREEMPT_DYNAMIC
static_call: Provide DEFINE_STATIC_CALL_RET0()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull tlb gather updates from Ingo Molnar:
"Theses fix MM (soft-)dirty bit management in the procfs code & clean
up the TLB gather API"
* tag 'core-mm-2021-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ldt: Use tlb_gather_mmu_fullmm() when freeing LDT page-tables
tlb: arch: Remove empty __tlb_remove_tlb_entry() stubs
tlb: mmu_gather: Remove start/end arguments from tlb_gather_mmu()
tlb: mmu_gather: Introduce tlb_gather_mmu_fullmm()
tlb: mmu_gather: Remove unused start/end arguments from tlb_finish_mmu()
mm: proc: Invalidate TLB after clearing soft-dirty page state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the irq subsystem:
- The usual new irq chip driver (Realtek RTL83xx)
- Removal of sirfsoc and tango irq chip drivers
- Conversion of the sun6i chip support to hierarchical irq domains
- The usual fixes, improvements and cleanups all over the place"
* tag 'irq-core-2021-02-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/imx: IMX_INTMUX should not default to y, unconditionally
irqchip/loongson-pch-msi: Use bitmap_zalloc() to allocate bitmap
irqchip/csky-mpintc: Prevent selection on unsupported platforms
irqchip: Add support for Realtek RTL838x/RTL839x interrupt controller
dt-bindings: interrupt-controller: Add Realtek RTL838x/RTL839x support
irqchip/ls-extirq: add IRQCHIP_SKIP_SET_WAKE to the irqchip flags
genirq: Use new tasklet API for resend_tasklet
dt-bindings: qcom,pdc: Add compatible for SM8350
dt-bindings: qcom,pdc: Add compatible for SM8250
irqchip/sun6i-r: Add wakeup support
irqchip/sun6i-r: Use a stacked irqchip driver
dt-bindings: irq: sun6i-r: Add a compatible for the H3
dt-bindings: irq: sun6i-r: Split the binding from sun7i-nmi
irqchip/gic-v3: Fix typos in PMR/RPR SCR_EL3.FIQ handling explanation
irqchip: Remove sirfsoc driver
irqchip: Remove sigma tango driver
|
|
Pull core block updates from Jens Axboe:
"Another nice round of removing more code than what is added, mostly
due to Christoph's relentless pursuit of tech debt removal/cleanups.
This pull request contains:
- Two series of BFQ improvements (Paolo, Jan, Jia)
- Block iov_iter improvements (Pavel)
- bsg error path fix (Pan)
- blk-mq scheduler improvements (Jan)
- -EBUSY discard fix (Jan)
- bvec allocation improvements (Ming, Christoph)
- bio allocation and init improvements (Christoph)
- Store bdev pointer in bio instead of gendisk + partno (Christoph)
- Block trace point cleanups (Christoph)
- hard read-only vs read-only split (Christoph)
- Block based swap cleanups (Christoph)
- Zoned write granularity support (Damien)
- Various fixes/tweaks (Chunguang, Guoqing, Lei, Lukas, Huhai)"
* tag 'for-5.12/block-2021-02-17' of git://git.kernel.dk/linux-block: (104 commits)
mm: simplify swapdev_block
sd_zbc: clear zone resources for non-zoned case
block: introduce blk_queue_clear_zone_settings()
zonefs: use zone write granularity as block size
block: introduce zone_write_granularity limit
block: use blk_queue_set_zoned in add_partition()
nullb: use blk_queue_set_zoned() to setup zoned devices
nvme: cleanup zone information initialization
block: document zone_append_max_bytes attribute
block: use bi_max_vecs to find the bvec pool
md/raid10: remove dead code in reshape_request
block: mark the bio as cloned in bio_iov_bvec_set
block: set BIO_NO_PAGE_REF in bio_iov_bvec_set
block: remove a layer of indentation in bio_iov_iter_get_pages
block: turn the nr_iovecs argument to bio_alloc* into an unsigned short
block: remove the 1 and 4 vec bvec_slabs entries
block: streamline bvec_alloc
block: factor out a bvec_alloc_gfp helper
block: move struct biovec_slab to bio.c
block: reuse BIO_INLINE_VECS for integrity bvecs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux
Pull oprofile and dcookies removal from Viresh Kumar:
"Remove oprofile and dcookies support
The 'oprofile' user-space tools don't use the kernel OPROFILE support
any more, and haven't in a long time. User-space has been converted to
the perf interfaces.
The dcookies stuff is only used by the oprofile code. Now that
oprofile's support is getting removed from the kernel, there is no
need for dcookies as well.
Remove kernel's old oprofile and dcookies support"
* tag 'oprofile-removal-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/linux:
fs: Remove dcookies support
drivers: Remove CONFIG_OPROFILE support
arch: xtensa: Remove CONFIG_OPROFILE support
arch: x86: Remove CONFIG_OPROFILE support
arch: sparc: Remove CONFIG_OPROFILE support
arch: sh: Remove CONFIG_OPROFILE support
arch: s390: Remove CONFIG_OPROFILE support
arch: powerpc: Remove oprofile
arch: powerpc: Stop building and using oprofile
arch: parisc: Remove CONFIG_OPROFILE support
arch: mips: Remove CONFIG_OPROFILE support
arch: microblaze: Remove CONFIG_OPROFILE support
arch: ia64: Remove rest of perfmon support
arch: ia64: Remove CONFIG_OPROFILE support
arch: hexagon: Don't select HAVE_OPROFILE
arch: arc: Remove CONFIG_OPROFILE support
arch: arm: Remove CONFIG_OPROFILE support
arch: alpha: Remove CONFIG_OPROFILE support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull ELF compat updates from Al Viro:
"Sanitizing ELF compat support, especially for triarch architectures:
- X32 handling cleaned up
- MIPS64 uses compat_binfmt_elf.c both for O32 and N32 now
- Kconfig side of things regularized
Eventually I hope to have compat_binfmt_elf.c killed, with both native
and compat built from fs/binfmt_elf.c, with -DELF_BITS={64,32} passed
by kbuild, but that's a separate story - not included here"
* 'work.elf-compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
get rid of COMPAT_ELF_EXEC_PAGESIZE
compat_binfmt_elf: don't bother with undef of ELF_ARCH
Kconfig: regularize selection of CONFIG_BINFMT_ELF
mips compat: switch to compat_binfmt_elf.c
mips: don't bother with ELF_CORE_EFLAGS
mips compat: don't bother with ELF_ET_DYN_BASE
mips: KVM_GUEST makes no sense for 64bit builds...
mips: kill unused definitions in binfmt_elf[on]32.c
mips binfmt_elf*32.c: use elfcore-compat.h
x32: make X32, !IA32_EMULATION setups able to execute x32 binaries
[amd64] clean PRSTATUS_SIZE/SET_PR_FPVALID up properly
elf_prstatus: collect the common part (everything before pr_reg) into a struct
binfmt_elf: partially sanitize PRSTATUS_SIZE and SET_PR_FPVALID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for
5.12-rc1.
It's been an active set of development in these subsystems for the
past few months:
- loads of typec features added for new hardware
- xhci features and bugfixes
- dwc3 features added for more hardware support
- dwc2 fixes and new hardware support
- cdns3 driver updates for more hardware support
- gadget driver cleanups and minor fixes
- usb-serial fixes, new driver, and more devices supported
- thunderbolt feature additions for new hardware
- lots of other tiny fixups and additions
The chrome driver changes are in here as well, as they depended on
some of the typec changes, and the maintainer acked them.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (300 commits)
dt-bindings: usb: mediatek: musb: add mt8516 compatbile
dt-bindings: usb: mtk-xhci: add compatible for mt2701 and mt7623
dt-bindings: usb: mtk-xhci: add optional assigned clock properties
Documentation: connector: Update the description of sink-vdos
usb: misc: usb3503: Fix logic in usb3503_init()
dt-bindings: usb: usb-device: fix typo in required properties
usb: Replace lkml.org links with lore
dt-bindings: usb: dwc3: add description for rk3328
dt-bindings: usb: convert rockchip,dwc3.txt to yaml
usb: quirks: add quirk to start video capture on ELMO L-12F document camera reliable
USB: quirks: sort quirk entries
USB: serial: drop bogus to_usb_serial_port() checks
USB: serial: make remove callback return void
USB: serial: drop if with an always false condition
usb: gadget: Assign boolean values to a bool variable
usb: typec: tcpm: Get Sink VDO from fwnode
dt-bindings: connector: Add SVDM VDO properties
usb: typec: displayport: Fill the negotiated SVDM Version in the header
usb: typec: ucsi: Determine common SVDM Version
usb: typec: tcpm: Determine common SVDM Version
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Borislav Petkov:
"Annotate new MMIO-accessing insn wrappers' arguments with __iomem"
* tag 'x86_asm_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Add a missing __iomem annotation in enqcmds()
x86/asm: Annotate movdir64b()'s dst argument with __iomem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build updates from Borislav Petkov:
- Treat R_386_PLT32 relocations like R_386_PC32 ones when building
- Add documentation about "make kvm_guest/xen.config" in "make help"
output
* tag 'x86_build_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build: Treat R_386_PLT32 relocation as R_386_PC32
x86/build: Realign archhelp
x86/build: Add {kvm_guest,xen}.config targets to make help's output
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 resource control updates from Borislav Petkov:
"Avoid IPI-ing a task in certain cases and prevent load/store tearing
when accessing a task's resctrl fields concurrently"
* tag 'x86_cache_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Apply READ_ONCE/WRITE_ONCE to task_struct.{rmid,closid}
x86/resctrl: Use task_curr() instead of task_struct->on_cpu to prevent unnecessary IPI
x86/resctrl: Add printf attribute to log function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 CPUID cleanup from Borislav Petkov:
"Assign a dedicated feature word to a CPUID leaf which is widely used"
* tag 'x86_cpu_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpufeatures: Assign dedicated feature word for CPUID_0x8000001F[EAX]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 FPU updates from Borislav Petkov:
"x86 fpu usage optimization and cleanups:
- make 64-bit kernel code which uses 387 insns request a x87 init
(FNINIT) explicitly when using the FPU
- misc cleanups"
* tag 'x86_fpu_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Use sizeof() instead of a constant
x86/fpu/64: Don't FNINIT in kernel_fpu_begin()
x86/fpu: Make the EFI FPU calling convention explicit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode cleanup from Borislav Petkov:
"Make the driver init function static again"
* tag 'x86_microcode_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Make microcode_init() static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 misc updates from Borislav Petkov:
- Complete the MSR write filtering by applying it to the MSR ioctl
interface too.
- Other misc small fixups.
* tag 'x86_misc_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MSR: Filter MSR writes through X86_IOC_WRMSR_REGS ioctl too
selftests/fpu: Fix debugfs_simple_attr.cocci warning
selftests/x86: Use __builtin_ia32_read/writeeflags
x86/reboot: Add Zotac ZBOX CI327 nano PCI reboot quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm cleanups from Borislav Petkov:
- PTRACE_GETREGS/PTRACE_PUTREGS regset selection cleanup
- Another initial cleanup - more to follow - to the fault handling
code.
- Other minor cleanups and corrections.
* tag 'x86_mm_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/{fault,efi}: Fix and rename efi_recover_from_page_fault()
x86/fault: Don't run fixups for SMAP violations
x86/fault: Don't look for extable entries for SMEP violations
x86/fault: Rename no_context() to kernelmode_fixup_or_oops()
x86/fault: Bypass no_context() for implicit kernel faults from usermode
x86/fault: Split the OOPS code out from no_context()
x86/fault: Improve kernel-executing-user-memory handling
x86/fault: Correct a few user vs kernel checks wrt WRUSS
x86/fault: Document the locking in the fault_signal_pending() path
x86/fault/32: Move is_f00f_bug() to do_kern_addr_fault()
x86/fault: Fold mm_fault_error() into do_user_addr_fault()
x86/fault: Skip the AMD erratum #91 workaround on unaffected CPUs
x86/fault: Fix AMD erratum #91 errata fixup for user code
x86/Kconfig: Remove HPET_EMULATE_RTC depends on RTC
x86/asm: Fixup TASK_SIZE_MAX comment
x86/ptrace: Clean up PTRACE_GETREGS/PTRACE_PUTREGS regset selection
x86/vm86/32: Remove VM86_SCREEN_BITMAP support
x86: Remove definition of DEBUG
x86/entry: Remove now unused do_IRQ() declaration
x86/mm: Remove duplicate definition of _PAGE_PAT_LARGE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 paravirt updates from Borislav Petkov:
"Part one of a major conversion of the paravirt infrastructure to our
kernel patching facilities and getting rid of the custom-grown ones"
* tag 'x86_paravirt_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pv: Rework arch_local_irq_restore() to not use popf
x86/xen: Drop USERGS_SYSRET64 paravirt call
x86/pv: Switch SWAPGS to ALTERNATIVE
x86/xen: Use specific Xen pv interrupt entry for DF
x86/xen: Use specific Xen pv interrupt entry for MCE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform updates from Borislav Petkov:
- Convert geode drivers to look up the LED controls from a GPIO machine
descriptor table.
- Remove arch/x86/platform/goldfish as it is not used by the android
emulator anymore.
* tag 'x86_platform_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/geode: Convert alix LED to GPIO machine descriptor
x86/platform/geode: Convert geode LED to GPIO machine descriptor
x86/platform/geode: Convert net5501 LED to GPIO machine descriptor
x86/platform: Retire arch/x86/platform/goldfish
x86/platform/intel-mid: Convert comma to semicolon
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SEV-ES fix from Borislav Petkov:
"Do not unroll string I/O for SEV-ES guests because they support it"
* tag 'x86_seves_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev-es: Do not unroll string I/O for SEV-ES guests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SGX fixes from Borislav Petkov:
"Random small fixes which missed the initial SGX submission. Also, some
procedural clarifications"
* tag 'x86_sgx_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Add Dave Hansen as reviewer for INTEL SGX
x86/sgx: Drop racy follow_pfn() check
MAINTAINERS: Fix the tree location for INTEL SGX patches
x86/sgx: Fix the return type of sgx_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ard Biesheuvel via Borislav Petkov:
"A few cleanups left and right, some of which were part of a initrd
measured boot series that needs some more work, and so only the
cleanup patches have been included for this release"
* tag 'efi-next-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Update debug prints to reflect other entropy sources
efi: x86: clean up previous struct mm switching
efi: x86: move mixed mode stack PA variable out of 'efi_scratch'
efi/libstub: move TPM related prototypes into efistub.h
efi/libstub: fix prototype of efi_tcg2_protocol::get_event_log()
efi/libstub: whitespace cleanup
efi: ia64: move IA64-only declarations to new asm/efi.h header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Borislav Petkov:
- move therm_throt.c to the thermal framework, where it belongs.
- identify CPUs which miss to enter the broadcast handler, as an
additional debugging aid.
* tag 'ras_updates_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
thermal: Move therm_throt there from x86/mce
x86/mce: Get rid of mcheck_intel_therm_init()
x86/mce: Make mce_timed_out() identify holdout CPUs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"After the last release contained a surprising amount of new 32-bit
machines, this time two thirds of the code changes are for 64-bit.
The usual updates to existing files include:
- Device tree compiler warning fixes for Berlin, Renesas, SoCFPGA,
nomadik, stm32, Allwinner, TI Keystone
- Support for additional devices on existing machines on Renesas,
SoCFPGA, at91, hisilicon, OMAP, Tegra, TI K3, Allwinner, Broadcom,
ux500, Mediatek, Marvell Armada, Marvell MMP, ZynqMP, AMLogic,
Qualcomm, i.MX, Layerscape, Actions, ASpeed, Toshiba
- Cleanups and minor fixes for Renesas, at91, mstar, ux500, Samsung,
stm32, Tegra, Broadcom, Mediatek, Marvell MMP, AMLogic, Qualcomm,
i.MX, Rockchip, ASpeed, Zynq
Only three new SoCs this time, but a number of boards across:
Renesas:
- Two Beacon EmbeddedWorks boards (RZ/G2H and RZ/G2N based)
Intel SoCFPGA:
- eASIC N5X board (N5X)
ST-Ericsson Ux500:
- Samsung GT-I9070 (Janice) phone (u8500)
TI OMAP:
- MYIR Tech Limited development board (AM335X)
Allwinner/sunxi:
- SL631 Action Camera (V3)
- PineTab Early Adopter tablet (A64)
Broadcom:
- BCM4906 networking chip
- Netgear R8000P router (BCM4906)
AMLogic:
- Hardkernel ODROID-HC4 development board (SM1)
- Beelink GS-King-X TV Box (S922X)
Qualcomm:
- Snapdragon 888 / SM8350 high-end phone SoC
- Qualcomm SDX55 5G modem as standalone SoC
- Snapdragon MTP reference board (SM8350)
- Snapdragon MTP reference board (SDX55)
- Sony Kitakami phones: Xperia Z3+/Z4/Z5 (APQ8094)
- Alcatel Idol 3 phone (MSM8916)
- ASUS Zenfone 2 Laser phone (MSM8916)
- BQ Aquaris X5 aka Longcheer L8910 phone (MSM8916)
- OnePlus6 phone (SDM845)
- OnePlus6T phone (SDM845)
- Alfa Network AP120C-AC access point (IPQ4018)
NXP i.MX6 (32-bit):
- Plymovent BAS base system controller for filter systems (imx6dl)
- Protonic MVT industrial touchscreen terminals (imx6dl)
- Protonic PRTI6G reference board (imx6ul)
- Kverneland UT1, UT1Q, UT1P, TGO agricultural terminals (imx6q/dl/qp)
NXP i.MX8 (64-bit)
- Beacon i.MX8M Nano development kit (imx8mn)
- Boundary Devices i.MX8MM Nitrogen SBC (imx8mm)
- Gateworks Venice i.MX 8M Mini Development Kits (imx8mm)
- phyBOARD-Pollux-i.MX8MP (imx8mp)
- Purism Librem5 Evergreen phone (imx8mp)
- Kontron SMARC-sAL28 system-on-module(imx8mp)
Rockchip:
- NanoPi M4B Single-board computer (RK3399)
- Radxa Rock Pi E router SBC (RK3328)
ASpeed:
- Ampere Mt. Jade, a BMC for an x86 server (AST2500)
- IBM Everest, a BMC for a Power10 server (AST2600)
- Supermicro x11spi, a BMC for an ARM server (AST2500)
Zynq:
- Ebang EBAZ4205, FPGA board (Zynq-7000)
- ZynqMP zcu104 revC reference platform (ZynqMP)"
* tag 'arm-dt-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (584 commits)
ARM: dts: aspeed: align GPIO hog names with dtschema
ARM: dts: aspeed: fix PCA95xx GPIO expander properties on Portwell
dt-bindings: spi: zynq: Convert Zynq QSPI binding to yaml
arm: dts: visconti: Add DT support for Toshiba Visconti5 GPIO driver
ARM: dts: aspeed: ast2600evb: Add enable ehci and uhci
ARM: dts: aspeed: mowgli: Add i2c rtc device
ARM: dts: aspeed: amd-ethanolx: Enable secondary LPC snooping address
dt-bindings: arm: xilinx: Add missing Zturn boards
ARM: dts: ebaz4205: add pinctrl entries for switches
ARM: dts: add Ebang EBAZ4205 device tree
dt-bindings: arm: add Ebang EBAZ4205 board
dt-bindings: add ebang vendor prefix
ARM: dts: aspeed: Add Everest BMC machine
ARM: dts: aspeed: inspur-fp5280g2: Add ipsps1 driver
ARM: dts: aspeed: inspur-fp5280g2: Add GPIO line names
ARM: dts: aspeed: Add Supermicro x11spi BMC machine
ARM: dts: aspeed: g220a: Fix some gpio
ARM: dts: aspeed: g220a: Enable ipmb
ARM: dts: aspeed: rainier: Add eMMC clock phase compensation
ARM: dts: aspeed: Add LCLK to lpc-snoop
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a number of additional device drivers that were added to the
kernel are now enabled in the respective configuration files.
A few of the files get updated to match the current Kconfig files for
removed or renamed options"
* tag 'arm-defconfig-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
ARM: configs: sama5_defconfig: add QSPI driver
ARM: configs: at91_dt_defconfig: add ov7740 module
ARM: configs: at91_dt_defconfig: add useful helper options
ARM: configs: at91: DT/ATAG defconfig modifications
ARM: configs: sama5_defconfig: update and remove unneeded options
ARM: configs: at91: enable drivers for sam9x60
arm64: defconfig: Enable RT5659
arm64: configs: Support DEVAPC on MediaTek platforms
arm64: configs: Support pwrap on Mediatek MT6779 platform
arm64: defconfig: Enable PF8x00 as builtin
ARM: multi_v7_defconfig: add STM32 CEC support
arm64: defconfig: Enable vibra-pwm
ARM: omap2plus_defconfig: Update for dropped options
ARM: omap2plus_defconfig: Update for moved options
ARM: multi_v7_defconfig: Enable nvmem's rmem driver
arm64: defconfig: Enable nvmem's rmem driver
ARM: multi_v7_defconfig: Enable support for the ADC thermal sensor
ARM: qcom_defconfig: Enable Command DB driver
ARM: qcom_defconfig: Enable RPMh power domain driver
ARM: qcom_defconfig: Enable ARM PSCI support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"This is mostly 32-bit code for SoC platforms, and looks smaller than
any such branch I remember from previous kernels, as most of this is
now handled in other subsystems for modern platforms:
- Minor bugfixes and Kconfig updates for Tegra, Broadcom, i.MX,
Renesas, and Samsung
- Updates to the MAINTAINERS listing for Actions, OMAP, and Samsung
- Samsung SoC driver updates to make them loadable modules"
* tag 'arm-soc-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: arm: samsung: include S3C headers in platform entry
MAINTAINERS: Add linux-actions ML for Actions Semi Arch
ARM: s3c: irq-s3c24xx: staticize local functions
ARM: s3c: irq-s3c24xx: include headers for missing declarations
ARM: s3c: fix fiq for clang IAS
ARM: imx: Remove unused IMX_GPIO_NR() macro
soc: renesas: rcar-sysc: Mark device node OF_POPULATED after init
ARM: OMAP2+: fix spellint typo
MAINTAINERS: Update address for OMAP GPMC driver
soc: renesas: rcar-sysc: Use readl_poll_timeout_atomic()
ARM: bcm: Select BRCMSTB_L2_IRQ for bcm2835
ARM: brcmstb: Add debug UART entry for 72116
ARM: tegra: Don't enable unused PLLs on resume from suspend
soc: samsung: pm_domains: Convert to regular platform driver
soc: samsung: exynos-chipid: correct helpers __init annotation
ARM: mach-imx: imx6ul: Print SOC revision on boot
ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup
soc: samsung: exynos-chipid: convert to driver and merge exynos-asv
soc: samsung: exynos-asv: handle reading revision register error
soc: samsung: exynos-asv: don't defer early on not-supported SoCs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only two left-over remaining non-urgent ARM SoC bug fixes:
- A build fix for the Atmel SAM9 platform to allow building with the
clang integrated assembler
- A DT fix for ethernet on Intel SoCFPGA, this has been broken since
it was added in v5.4"
* tag 'arm-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: at91: use proper asm syntax in pm_suspend
arm64: dts: agilex: fix phy interface bit shift for gmac1 and gmac2
|
|
Pull networking updates from David Miller:
"Here is what we have this merge window:
1) Support SW steering for mlx5 Connect-X6Dx, from Yevgeny Kliteynik.
2) Add RSS multi group support to octeontx2-pf driver, from Geetha
Sowjanya.
3) Add support for KS8851 PHY. From Marek Vasut.
4) Add support for GarfieldPeak bluetooth controller from Kiran K.
5) Add support for half-duplex tcan4x5x can controllers.
6) Add batch skb rx processing to bcrm63xx_enet, from Sieng Piaw
Liew.
7) Rework RX port offload infrastructure, particularly wrt, UDP
tunneling, from Jakub Kicinski.
8) Add BCM72116 PHY support, from Florian Fainelli.
9) Remove Dsa specific notifiers, they are unnecessary. From Vladimir
Oltean.
10) Add support for picosecond rx delay in dwmac-meson8b chips. From
Martin Blumenstingl.
11) Support TSO on xfrm interfaces from Eyal Birger.
12) Add support for MP_PRIO to mptcp stack, from Geliang Tang.
13) Support BCM4908 integrated switch, from Rafał Miłecki.
14) Support for directly accessing kernel module variables via module
BTF info, from Andrii Naryiko.
15) Add DASH (esktop and mobile Architecture for System Hardware)
support to r8169 driver, from Heiner Kallweit.
16) Add rx vlan filtering to dpaa2-eth, from Ionut-robert Aron.
17) Add support for 100 base0x SFP devices, from Bjarni Jonasson.
18) Support link aggregation in DSA, from Tobias Waldekranz.
19) Support for bitwidse atomics in bpf, from Brendan Jackman.
20) SmartEEE support in at803x driver, from Russell King.
21) Add support for flow based tunneling to GTP, from Pravin B Shelar.
22) Allow arbitrary number of interconnrcts in ipa, from Alex Elder.
23) TLS RX offload for bonding, from Tariq Toukan.
24) RX decap offklload support in mac80211, from Felix Fietkou.
25) devlink health saupport in octeontx2-af, from George Cherian.
26) Add TTL attr to SCM_TIMESTAMP_OPT_STATS, from Yousuk Seung
27) Delegated actionss support in mptcp, from Paolo Abeni.
28) Support receive timestamping when doin zerocopy tcp receive. From
Arjun Ray.
29) HTB offload support for mlx5, from Maxim Mikityanskiy.
30) UDP GRO forwarding, from Maxim Mikityanskiy.
31) TAPRIO offloading in dsa hellcreek driver, from Kurt Kanzenbach.
32) Weighted random twos choice algorithm for ipvs, from Darby Payne.
33) Fix netdev registration deadlock, from Johannes Berg.
34) Various conversions to new tasklet api, from EmilRenner Berthing.
35) Bulk skb allocations in veth, from Lorenzo Bianconi.
36) New ethtool interface for lane setting, from Danielle Ratson.
37) Offload failiure notifications for routes, from Amit Cohen.
38) BCM4908 support, from Rafał Miłecki.
39) Support several new iwlwifi chips, from Ihab Zhaika.
40) Flow drector support for ipv6 in i40e, from Przemyslaw Patynowski.
41) Support for mhi prrotocols, from Loic Poulain.
42) Optimize bpf program stats.
43) Implement RFC6056, for better port randomization, from Eric
Dumazet.
44) hsr tag offloading support from George McCollister.
45) Netpoll support in qede, from Bhaskar Upadhaya.
46) 2005/400g speed support in bonding 3ad mode, from Nikolay
Aleksandrov.
47) Netlink event support in mptcp, from Florian Westphal.
48) Better skbuff caching, from Alexander Lobakin.
49) MRP (Media Redundancy Protocol) offloading in DSA and a few
drivers, from Horatiu Vultur.
50) mqprio saupport in mvneta, from Maxime Chevallier.
51) Remove of_phy_attach, no longer needed, from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1766 commits)
octeontx2-pf: Fix otx2_get_fecparam()
cteontx2-pf: cn10k: Prevent harmless double shift bugs
net: stmmac: Add PCI bus info to ethtool driver query output
ptp: ptp_clockmatrix: clean-up - parenthesis around a == b are unnecessary
ptp: ptp_clockmatrix: Simplify code - remove unnecessary `err` variable.
ptp: ptp_clockmatrix: Coding style - tighten vertical spacing.
ptp: ptp_clockmatrix: Clean-up dev_*() messages.
ptp: ptp_clockmatrix: Remove unused header declarations.
ptp: ptp_clockmatrix: Add alignment of 1 PPS to idtcm_perout_enable.
ptp: ptp_clockmatrix: Add wait_for_sys_apll_dpll_lock.
net: stmmac: dwmac-sun8i: Add a shutdown callback
net: stmmac: dwmac-sun8i: Minor probe function cleanup
net: stmmac: dwmac-sun8i: Use reset_control_reset
net: stmmac: dwmac-sun8i: Remove unnecessary PHY power check
net: stmmac: dwmac-sun8i: Return void from PHY unpower
r8169: use macro pm_ptr
net: mdio: Remove of_phy_attach()
net: mscc: ocelot: select PACKING in the Kconfig
net: re-solve some conflicts after net -> net-next merge
net: dsa: tag_rtl4_a: Support also egress tags
...
|
|
Allow building x86 with PREEMPT_DYNAMIC=n, this is needed for
PREEMPT_RT as it makes no sense to not have full preemption on
PREEMPT_RT.
Fixes: 8c98e8cf723c ("preempt/dynamic: Provide preempt_schedule[_notrace]() static calls")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Mike Galbraith <efault@gmx.de>
Link: https://lkml.kernel.org/r/YCK1+JyFNxQnWeXK@hirez.programming.kicks-ass.net
|
|
Following the idle loop model, cleanly check for pending rcuog wakeup
before the last rescheduling point upon resuming to guest mode. This
way we can avoid to do it from rcu_user_enter() with the last resort
self-IPI hack that enforces rescheduling.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210131230548.32970-6-frederic@kernel.org
|
|
Use the new EXPORT_STATIC_CALL_TRAMP() / static_call_mod() to unexport
the static_call_key for the PREEMPT_DYNAMIC calls such that modules
can no longer update these calls.
Having modules change/hi-jack the preemption calls would be horrible.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When exporting static_call_key; with EXPORT_STATIC_CALL*(), the module
can use static_call_update() to change the function called. This is
not desirable in general.
Not exporting static_call_key however also disallows usage of
static_call(), since objtool needs the key to construct the
static_call_site.
Solve this by allowing objtool to create the static_call_site using
the trampoline address when it builds a module and cannot find the
static_call_key symbol. The module loader will then try and map the
trampole back to a key before it constructs the normal sites list.
Doing this requires a trampoline -> key associsation, so add another
magic section that keeps those.
Originally-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210127231837.ifddpn7rhwdaepiu@treble
|
|
Provide static calls to control preempt_schedule[_notrace]()
(called in CONFIG_PREEMPT) so that we can override their behaviour when
preempt= is overriden.
Since the default behaviour is full preemption, both their calls are
initialized to the arch provided wrapper, if any.
[fweisbec: only define static calls when PREEMPT_DYNAMIC, make it less
dependent on x86 with __preempt_schedule_func]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-7-frederic@kernel.org
|
|
Preemption mode selection is currently hardcoded on Kconfig choices.
Introduce a dedicated option to tune preemption flavour at boot time,
This will be only available on architectures efficiently supporting
static calls in order not to tempt with the feature against additional
overhead that might be prohibitive or undesirable.
CONFIG_PREEMPT_DYNAMIC is automatically selected by CONFIG_PREEMPT if
the architecture provides the necessary support (CONFIG_STATIC_CALL_INLINE,
CONFIG_GENERIC_ENTRY, and provide with __preempt_schedule_function() /
__preempt_schedule_notrace_function()).
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
[peterz: relax requirement to HAVE_STATIC_CALL]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-5-frederic@kernel.org
|
|
Provide a stub function that return 0 and wire up the static call site
patching to replace the CALL with a single 5 byte instruction that
clears %RAX, the return value register.
The function can be cast to any function pointer type that has a
single %RAX return (including pointers). Also provide a version that
returns an int for convenience. We are clearing the entire %RAX register
in any case, whether the return value is 32 or 64 bits, since %RAX is
always a scratch register anyway.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210118141223.123667-2-frederic@kernel.org
|
|
The only remaining use of MAX_USER_PRIO (and USER_PRIO) is the
SCALE_PRIO() definition in the PowerPC Cell architecture's Synergistic
Processor Unit (SPU) scheduler. TASK_USER_PRIO isn't used anymore.
Commit fe443ef2ac42 ("[POWERPC] spusched: Dynamic timeslicing for
SCHED_OTHER") copied SCALE_PRIO() from the task scheduler in v2.6.23.
Commit a4ec24b48dde ("sched: tidy up SCHED_RR") removed it from the task
scheduler in v2.6.24.
Commit 3ee237dddcd8 ("sched/prio: Add 3 macros of MAX_NICE, MIN_NICE and
NICE_WIDTH in prio.h") introduced NICE_WIDTH much later.
With:
MAX_USER_PRIO = USER_PRIO(MAX_PRIO)
= MAX_PRIO - MAX_RT_PRIO
MAX_PRIO = MAX_RT_PRIO + NICE_WIDTH
MAX_USER_PRIO = MAX_RT_PRIO + NICE_WIDTH - MAX_RT_PRIO
MAX_USER_PRIO = NICE_WIDTH
MAX_USER_PRIO can be replaced by NICE_WIDTH to be able to remove all the
{*_}USER_PRIO defines.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20210128131040.296856-3-dietmar.eggemann@arm.com
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-02-16
The following pull-request contains BPF updates for your *net-next* tree.
There's a small merge conflict between 7eeba1706eba ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f8161 ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:
[...]
lock_sock(sk);
err = tcp_zerocopy_receive(sk, &zc, &tss);
err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
&zc, &len, err);
release_sock(sk);
[...]
We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).
The main changes are:
1) Adds support of pointers to types with known size among global function
args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.
2) Add bpf_iter for task_vma which can be used to generate information similar
to /proc/pid/maps, from Song Liu.
3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
rewriting bind user ports from BPF side below the ip_unprivileged_port_start
range, both from Stanislav Fomichev.
4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
as well as per-cpu maps for the latter, from Alexei Starovoitov.
5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
for sleepable programs, both from KP Singh.
6) Extend verifier to enable variable offset read/write access to the BPF
program stack, from Andrei Matei.
7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
query device MTU from programs, from Jesper Dangaard Brouer.
8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
tracing programs, from Florent Revest.
9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
otherwise too many passes are required, from Gary Lin.
10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
verification both related to zero-extension handling, from Ilya Leoshkevich.
11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.
12) Batch of AF_XDP selftest cleanups and small performance improvement
for libbpf's xsk map redirect for newer kernels, from Björn Töpel.
13) Follow-up BPF doc and verifier improvements around atomics with
BPF_FETCH, from Brendan Jackman.
14) Permit zero-sized data sections e.g. if ELF .rodata section contains
read-only data from local variables, from Yonghong Song.
15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ethernet controller node in Toshiba Visconti5 SoC-specific DT file.
And enable this node in TMPV7708 RM main board's board-specific DT file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- New driver for the MIPS-based Realtek RTL838x/RTL839x SoC
- Conversion of the sun6i-r support code to a hierarchical setup
- Fix wake-up interrupts for the ls-extirq driver
- Fix MSI allocation for the loongson-pch-msi driver
- Add compatible strings for new Qualcomm SoCs
- Tidy up a few Kconfig entries (IMX, CSKY)
- Spelling phyksiz
- Remove the sirfsoc and tango drivers
Link: https://lore.kernel.org/r/20210214124015.3333457-1-maz@kernel.org
|
|
dtschema for pca95xx expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210212162640.66677-2-krzk@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PCA95xx GPIO expander requires GPIO controller properties to operate
properly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210212162640.66677-1-krzk@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
- Use pkg-config for scripts/sign-file.c CFLAGS
* tag 'kbuild-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
scripts: set proper OpenSSL include dir also for sign-file
sparc: remove wrong comment from arch/sparc/include/asm/Kbuild
kbuild: fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"I kinda knew while typing 'I hope this is the last batch of x86/urgent
updates' last week, Murphy was reading too and uttered 'Hold my
beer!'.
So here's more fixes... Thanks Murphy.
Anyway, three more x86/urgent fixes for 5.11 final. We should be
finally ready (famous last words). :-)
- An SGX use after free fix
- A fix for the fix to disable CET instrumentation generation for
kernel code. We forgot 32-bit, which we seem to do very often
nowadays
- A Xen PV fix to irqdomain init ordering"
* tag 'x86_urgent_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci: Create PCI/MSI irqdomain after x86_init.pci.arch_init()
x86/build: Disable CET instrumentation in the kernel for 32-bit too
x86/sgx: Maintain encl->refcount for each encl->mm_list entry
|
|
These are NOT exported to userspace.
The headers listed in arch/sparc/include/uapi/asm/Kbuild are exported.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Merge fixes from Andrew Morton:
"6 patches.
Subsystems affected by this patch series: mm/pagemap, scripts,
MAINTAINERS, and h8300"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
h8300: fix PREEMPTION build, TI_PRE_COUNT undefined
MAINTAINERS: add Andrey Konovalov to KASAN reviewers
MAINTAINERS: update Andrey Konovalov's email address
MAINTAINERS: update KASAN file list
scripts/recordmcount.pl: support big endian for ARCH sh
m68k: make __pfn_to_phys() and __phys_to_pfn() available for !MMU
|
|
Fix a build error for undefined 'TI_PRE_COUNT' by adding it to
asm-offsets.c.
h8300-linux-ld: arch/h8300/kernel/entry.o: in function `resume_kernel': (.text+0x29a): undefined reference to `TI_PRE_COUNT'
Link: https://lkml.kernel.org/r/20210212021650.22740-1-rdunlap@infradead.org
Fixes: df2078b8daa7 ("h8300: Low level entry")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Recent changes that obsoleted DISCONTIGMEM on m68k switched the MMU
variant to use generic definitions of __pfn_to_phys() and __phys_to_pfn(),
but missed the !MMU variant which caused a build failure:
drivers/media/common/videobuf2/videobuf2-dma-contig.c: In function 'vb2_dc_get_userptr':
drivers/media/common/videobuf2/videobuf2-dma-contig.c:509:5: error: implicit declaration of function '__pfn_to_phys' [-Werror=implicit-function-declaration]
509 | __pfn_to_phys(nums[0]), size, buf->dma_dir, 0);
| ^~~~~~~~~~~~~
cc1: some warnings being treated as errors
Enable __pfn_to_phys() and __phys_to_pfn() on !MMU builds.
Link: https://lkml.kernel.org/r/20210211232202.GS299309@linux.ibm.com
Fixes: 4bfc848e0981 ("m68k/mm: enable use of generic memory_model.h for !DISCONTIGMEM")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A single fix for an issue introduced this development cycle: when
running as a Xen guest on Arm systems the kernel will hang during
boot"
* tag 'for-linus-5.11-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: Don't probe xenbus as part of an early initcall
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Palmer Dabbelt:
"A single fix this week: the removal of the GPIO reset method for the
Ethernet phy on the HiFive Unleashed.
This returns to relying on the bootloader's phy reset sequence, which
we'll have to continue doing until we can sort out how to get the
Linux phy driver to perform the special reset dance required for this
phy"
* tag 'riscv-for-linus-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Revert "dts: phy: add GPIO number and active state used for phy reset"
|