Age | Commit message (Collapse) | Author | Files | Lines |
|
Add to Trats2 DTS new node for configuring the max77693 charger driver.
Only the maxim,constant-microvolt differs from default value but set all
of the optional properties anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Remove fixed regulators (duplicating what max77686 provides) and
add GPIO enable control to max77686 regulators.
This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.
Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
- ENB9 GPIO (turned always on by regulator-fixed),
- BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
exynos4412-trats2
Add suspend to RAM configuration for max77686 regulators. Some LDOs
and bucks are disabled. This reduces energy consumption during S2R,
approximately from 17 mA to 9 mA.
Additionally remove old and not supported bindings:
- regulator-mem-off
- regulator-mem-idle
- regulator-mem-on
The max77686 driver does not parse them and they are not documented
anywere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add node for fuel gauge present in Maxim 77693 PMIC. This allows control
over battery charging state on Trats2 board.
The fuel gauge is compatible with max17042 battery driver (Maxim
17042/17047/17050). Although datasheet rev 2.2 for MAX77693 describes
fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies
itself as Maxim 17047-like.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The odroid-xu3 has 4 INA231 current sensors on board which can be
accessed from the Linux via the hwmon interface.
There is one sensor for each of these power rails:
- A15 cluster: VDD_ARM
- A7 cluster: VDD_KFC
- GPU: VDD_G3D
- memory: VDD_MEM
In addition to adding the sensors, LDO26 from the PMIC needs to be
enabled because it's powering these sensor.
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds regulator-haptic device node controlled by regulator.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds regulator-haptic device node controlled by regulator.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
All currently supported boards use hsotg/dwc2 controller in device
('peripheral') mode, so add property which sets correct operation mode.
This patch fixes support in recent changes in dwc2 driver, which added
support for dual-role devices.
Suggested-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch replaces all custom samsung,power-domain dt
properties with generic power domain bindings and updates
documentation Samsung's devices referring to old binding.
Suggested-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[javier.martinez@collabora.co.uk: tested on the Exynos5800 Peach Pi Chromebook]
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.
To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have both
a power and lid GPIO keys but only the former was defined in the
DTS. Add DTS snippets for the lid GPIO key too. These were taken
from the downstream ChromeOS 3.8 kernel tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos5250 Snow Chromebook has GPIO keys for power and lid
so the SoC I/O pins have to be configured in external interrupt
mode. Currently, this is working without setting the pinctrl
lines but is better to set it explicitly instead of relying on
the previous state of the I/O pins.
The DTS snippets were taken from the downstream ChromeOS tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds MIPI-DSI and MIPI-DSI based S6E63J0X03 AMOLED panel
device nodes for Exynos3250 Rinato board.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds fimd device node which is a display controller
for Exynos3250 Rinato board.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch replaces number by macro in gpio keys for exynos3250 boards.
Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch removes unnecessary property of gpio-keys node. The
gpio-keys driver doesn't use interrupts and interrupt-parent.
Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch enables hsotg and usbphy node to use USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds device tree node for exynos_usbphy to use USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel
Pull arch/hexagon updates from Richard Kuo:
"Build cleanup and a few misc fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: fix signal delivery for debug traps
Hexagon: set ARCH_DMA_MINALIGN
Hexagon: fix alignment of init_task in RW_DATA_SECTION
hexagon: Fix build failures in linux-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/chris updates from Jesper Nilsson:
"Mostly cleanup and build fixes for CRISv32 allmodconfig
God Jul och Gott Nytt år!"
* tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
CRISv32: ETRAXFS: Fix recursive spinlock
CRISv32: Select MTDRAM for axisflashmap
CRISv32: Implement early console
CRIS: Use KALLSYMs if available in call stack dump
CRISv32: Fix declaration mismatch
CRISv32: Rewrite of synchronous serial port driver
CRIS: Update init memory handling
CRISv32: Better handling of watchdog bite
CRIS: Export missing function symbols
CRIS: Export ioremap_nocache
CRIS: Fix headers_install
CRISv32: Add missing include for mm.h
CRISv32: Drop obsolete file for SPI driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 __get_cpu_var removal from Tony Luck:
"__get_cpu_var removed from rest of tree, drop reference from comments
in arch/ia64"
* tag 'please-pull-misc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Update comment that references __get_cpu_var
|
|
There are no users of this symbol left.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Move pinmux alloc/dealloc code into functions that don't take
the spinlock so we can use from code that has the spinlock already.
CRISv32 has no working SMP, so spinlocks becomes a NOP,
so deadlock was never seen.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Fixes compile error on allmodconfig.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Also, print kernel version on oops.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Drop i2c_init from this header, it was declared non-static here,
but static in the C-file.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Make driver possible to load as a module and try to handle
locking better.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
- Add free_initrd_mem as found by Guenter Roeck <linux@roeck-us.net>
- Add free_init_pages
- Export empty_zero_page symbol
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Don't enter watchdog handling if we're already in watchdog handling.
Also some minor formatting tweaks.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
strcmp was lost when all other string functions were removed,
but we still have an optimized version for this on CRISv32,
so any driver built as a module would not have access to this symbol.
In a similar manner, we had optimized versions of
csum_partial_copy_from_user and __do_clear_user
but no exported symbols for them, breaking bunch of other drivers
when built as a module.
At the same time, move EXPORT_SYMBOL(__copy_user) and
EXPORT_SYMBOL(__copy_user_zeroing) C-files so it's
located together with the function definition.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Fix headers_install by adjusting the path to arch files.
And delete unused Kbuild file.
Drop special handling of cris in the headers.sh script
as a nice side-effect.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
Fixes the following compile error.
arch/cris/arch-v32/kernel/time.c: In function 'reset_watchdog':
arch/cris/arch-v32/kernel/time.c:121:2:
error: implicit declaration of function 'global_page_state'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
File was already deleted.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
|
|
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"This contains a single TLS ABI validation fix from Andy Lutomirski"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Don't validate lm in set_thread_area() after all
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes and cleanups from Ingo Molnar:
"A kernel fix plus mostly tooling fixes, but also some tooling
restructuring and cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf: Fix building warning on ARM 32
perf symbols: Fix use after free in filename__read_build_id
perf evlist: Use roundup_pow_of_two
tools: Adopt roundup_pow_of_two
perf tools: Make the mmap length autotuning more robust
tools: Adopt rounddown_pow_of_two and deps
tools: Adopt fls_long and deps
tools: Move bitops.h from tools/perf/util to tools/
tools: Introduce asm-generic/bitops.h
tools lib: Move asm-generic/bitops/find.h code to tools/include and tools/lib
tools: Whitespace prep patches for moving bitops.h
tools: Move code originally from asm-generic/atomic.h into tools/include/asm-generic/
tools: Move code originally from linux/log2.h to tools/include/linux/
tools: Move __ffs implementation to tools/include/asm-generic/bitops/__ffs.h
perf evlist: Do not use hard coded value for a mmap_pages default
perf trace: Let the perf_evlist__mmap autosize the number of pages to use
perf evlist: Improve the strerror_mmap method
perf evlist: Clarify sterror_mmap variable names
perf evlist: Fixup brown paper bag on "hint" for --mmap-pages cmdline arg
perf trace: Provide a better explanation when mmap fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
|