| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Unlike global OOM handling, memory cgroup code will invoke the OOM killer
in any OOM situation because it has no way of telling faults occuring in
kernel context - which could be handled more gracefully - from
user-triggered faults.
Pass a flag that identifies faults originating in user space from the
architecture-specific fault handlers to generic code so that memcg OOM
handling can be improved.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The memcg code can trap tasks in the context of the failing allocation
until an OOM situation is resolved. They can hold all kinds of locks
(fs, mm) at this point, which makes it prone to deadlocking.
This series converts memcg OOM handling into a two step process that is
started in the charge context, but any waiting is done after the fault
stack is fully unwound.
Patches 1-4 prepare architecture handlers to support the new memcg
requirements, but in doing so they also remove old cruft and unify
out-of-memory behavior across architectures.
Patch 5 disables the memcg OOM handling for syscalls, readahead, kernel
faults, because they can gracefully unwind the stack with -ENOMEM. OOM
handling is restricted to user triggered faults that have no other
option.
Patch 6 reworks memcg's hierarchical OOM locking to make it a little
more obvious wth is going on in there: reduce locked regions, rename
locking functions, reorder and document.
Patch 7 implements the two-part OOM handling such that tasks are never
trapped with the full charge stack in an OOM situation.
This patch:
Back before smart OOM killing, when faulting tasks were killed directly on
allocation failures, the arch-specific fault handlers needed special
protection for the init process.
Now that all fault handlers call into the generic OOM killer (see commit
609838cfed97: "mm: invoke oom-killer from remaining unconverted page
fault handlers"), which already provides init protection, the
arch-specific leftovers can be removed.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently hugepage migration works well only for pmd-based hugepages
(mainly due to lack of testing,) so we had better not enable migration of
other levels of hugepages until we are ready for it.
Some users of hugepage migration (mbind, move_pages, and migrate_pages) do
page table walk and check pud/pmd_huge() there, so they are safe. But the
other users (softoffline and memory hotremove) don't do this, so without
this patch they can try to migrate unexpected types of hugepages.
To prevent this, we introduce hugepage_migration_support() as an
architecture dependent check of whether hugepage are implemented on a pmd
basis or not. And on some architecture multiple sizes of hugepages are
available, so hugepage_migration_support() also checks hugepage size.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
|
|
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
|
|
These are based on the current shipping versions of the config files
from Tilera, as synced up to the tip, so are a better starting point
for folks who want a default configuration.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The macrology in cmpxchg.h was designed to allow arbitrary pointer
and integer values to be passed through the routines. To support
cmpxchg() on 64-bit values on the 32-bit tilepro architecture, we
used the idiom "(typeof(val))(typeof(val-val))". This way, in the
"size 8" branch of the switch, when the underlying cmpxchg routine
returns a 64-bit quantity, we cast it first to a typeof(val-val)
quantity (i.e. size_t if "val" is a pointer) with no warnings about
casting between pointers and integers of different sizes, then cast
onwards to typeof(val), again with no warnings. If val is not a
pointer type, the additional cast is a no-op. We can't replace the
typeof(val-val) cast with (for example) unsigned long, since then if
"val" is really a 64-bit type, we cast away the high bits.
HOWEVER, this fails with current gcc (through 4.7 at least) if "val"
is a pointer to an incomplete type. Unfortunately gcc isn't smart
enough to realize that "val - val" will always be a size_t type
even if it's an incomplete type pointer.
Accordingly, I've reworked the way we handle the casting. We have
given up the ability to use cmpxchg() on 64-bit values on tilepro,
which is OK in the kernel since we should use cmpxchg64() explicitly
on such values anyway. As a result, I can just use simple "unsigned
long" casts internally.
As I reworked it, I realized it would be cleaner to move the
architecture-specific conditionals for cmpxchg and xchg out of the
atomic.h headers and into cmpxchg, and then use the cmpxchg() and
xchg() primitives directly in atomic.h and elsewhere. This allowed
the cmpxchg.h header to stand on its own without relying on the
implicit include of it that is performed by <asm/atomic.h>.
It also allowed collapsing the atomic_xchg/atomic_cmpxchg routines
from atomic_{32,64}.h into atomic.h.
I improved the tests that guard the allowed size of the arguments
to the routines to use a __compiletime_error() test. (By avoiding
the use of BUILD_BUG, I could include cmpxchg.h into bitops.h as
well and use the macros there, which is otherwise impossible due
to include order dependency issues.)
The tilepro _atomic_xxx internal methods were previously set up to
take atomic_t and atomic64_t arguments, which isn't as convenient
with the new model, so I modified them to take int or u64 arguments,
which is consistent with how they used the arguments internally
anyway, so provided some nice simplification there too.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
This change sets the PCI devices' initial DMA capabilities
conservatively and promotes them at the request of the driver,
as opposed to assuming advanced DMA capabilities. The old design
runs the risk of breaking drivers that assume default capabilities.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Should check the return value of kzalloc first to avoid the null pointer.
Then can dereference the non-null pointer to access the fields of struct
resource.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This was really only useful for TILE64 when we mapped the
kernel data with small pages. Now we use a huge page and we
really don't want to map different parts of the kernel
data in different ways.
We retain the __write_once name in case we want to bring
it back to life at some point in the future.
Note that this change uncovered a latent bug where the
"smp_topology" variable happened to always be aligned mod 8
so we could store two "int" values at once, but when we
eliminated __write_once it ended up only aligned mod 4.
Fix with an explicit annotation.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This chip is no longer being actively developed for (it was superceded
by the TILEPro64 in 2008), and in any case the existing compiler and
toolchain in the community do not support it. It's unlikely that the
kernel works with TILE64 at this point as the configuration has not been
tested in years. The support is also awkward as it requires maintaining
a significant number of ifdefs. So, just remove it altogether.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The definisions of __ffs(), __fls(), and ffs() for tile are almost same
as asm-generic/bitops-*.h. The only difference is that it is defined
as __always_inline or inline. So this switches to use those headers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [moved #includes to end]
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We were rolling our own bundle_bits, which is unnecessary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
There's no need to make up new ways of computing the addresses
of the Tilera hypervisor APIs; just use the standard method
of relying on the symbols to provide the addresses.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Also fix mentions of it in #error statements.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
It was bombed away because it was previously marked as __devinit,
but it should be an __init function.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
If we wait until after including a bunch of other files, we
will have generated so much warning spew that it's hard to
notice the error about using the wrong compiler.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Explain the rationale of not overlapping the 64-bit DMA window
with the PA range.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
It isn't used any more by us now that the generic kernel build
offers DEBUG_INFO_REDUCED, so just get rid of it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We use virt_to_pte(NULL, va) a lot, which isn't very obvious.
I added virt_to_kpte(va) as a more obvious wrapper function,
that also validates the va as being a kernel adddress.
And, I fixed the semantics of virt_to_pte() so that we handle
the pud and pmd the same way, and we now document the fact that
we handle the final pte level differently.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Allow enabling frame pointer support; this makes it easier to hook
into the various kernel features that claim they require it without
having to add Kconfig conditionals everywhere (a la mips, ppc, s390,
and microblaze). When enabled, it basically eliminates leaf functions
as such, and stops optimizing tail and sibling calls. It adds around
3% to the size of the kernel when enabled.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Newer hypervisors have an API for reporting per-cpu statistics
information. This change allows seeing that information via
/sys/devices/system/cpu/cpuN/hv_stats file for each core.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Enter kernel debugger at boot with:
--hvd UART_1=1 --hvx kgdbwait --hvx kgdboc=ttyS1,115200
or at runtime with:
echo ttyS1,115200 > /sys/module/kgdboc/parameters/kgdboc
echo g > /proc/sysrq-trigger
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The TILE-Gx chip includes an on-chip UART. This change adds support
for using the UART from within the kernel. The UART shim has more
functionality than is exposed here, but to keep the kernel code and
binary simpler, this is a subset of the full API designed to enable
a standard Linux tty serial driver only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The existing code relied on the hardware definition (<arch/chip.h>)
to specify how much VA and PA space was available. It's convenient
to allow customizing this for some configurations, so provide symbols
MAX_PA_WIDTH and MAX_VA_WIDTH in <asm/page.h> that can be modified
if desired.
Additionally, move away from the MEM_XX_INTRPT nomenclature to
define the start of various regions within the VA space. In fact
the cleaner symbol is, for example, MEM_SV_START, to indicate the
start of the area used for supervisor code; the actual address of the
interrupt vectors is not as important, and can be changed if desired.
As part of this change, convert from "intrpt1" nomenclature (which
built in the old privilege-level 1 model) to a simple "intrpt".
Also strip out some tilepro-specific code supporting modifying the
PL the kernel could run at, since we don't actually support using
different PLs in tilepro, only tilegx.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Technically, user privilege is anything less than kernel
privilege. We modify the existing user_mode() macro to have
this semantic (and use it in a couple of places it wasn't being
used before), and add an IS_KERNEL_EX1() macro to the assembly
code as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We remove some debug code in relocate_kernel_64.S that made raw
calls to the hv_console_putc Tilera hypervisor API, since everything
should funnel through the early_hv_write() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This tile-specific API had a minor bug, in that if a super huge (>4GB)
page mapped a particular address range, we wouldn't handle it correctly.
As part of fixing that bug, I also cleaned up some of the pud and pmd
accessors to make them more consistent.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Previously, we used a special-purpose register (SPR_SYSTEM_SAVE_K_0)
to hold the CPU number and the top of the current kernel stack
by using the low bits to hold the CPU number, and using the high
bits to hold the address of the page just above where we'd want
the kernel stack to be. That way we could initialize a new SP
when first entering the kernel by just masking the SPR value and
subtracting a couple of words.
However, it's actually more useful to be able to place an arbitrary
kernel-top value in the SPR. This allows us to create a new stack
context (e.g. for virtualization) with an arbitrary top-of-stack VA.
To make this work, we now store the CPU number in the high bits,
above the highest legal VA bit (42 bits in the current tilegx
microarchitecture). The full 42 bits are thus available to store the
top of stack value. Getting the current cpu (a relatively common
operation) is still fast; it's now a shift rather than a mask.
We make this change only for tilegx, since tilepro has too few SPR
bits to do this, and we don't need this support on tilepro anyway.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We use the validate_current() API to make sure that "current" seems
plausible before using it. With the new show_regs_print_info()
API, we want to check that current is OK before calling it, since
otherwise we will end up in a recursive panic.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Normally the build doesn't include these warnings, but at one
point I built with -Wsign-compare, and noticed a few things that
are technically bugs. This change fixes those things.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
With this change such sections are grouped with regular text
in the vmlinux image; this change puts them at the front,
which is where the standard Linux includes .text.hot*.
This change should fix a recently-observed bug where a bunch of
symbols were being omitted from the /proc/kallsyms output
because they fell between _etext and _sinittext.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
In strncpy_from_user_asm, when the destination buffer length was the
same as the actual string length, we were returning the size of the
destination buffer. But since it's a NUL terminated string, we should
return the length of the string instead.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Nothing in the codebase was using them, and as written they took
"unsigned long" as the physical address rather than "phys_addr_t",
which is wrong on tilepro anyway. Rather than fixing stale APIs,
just remove them; if there's ever demand for them on this platform,
we can put them back.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
We had been doing an automatic full eviction of the L1 I$
everywhere whenever we did a kernel-space TLB flush. It turns
out this isn't necessary, since all the callers already handle
doing a flush if necessary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This enables support for "kexec --initrd" for tile.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
With this change, tile Linux now supports address-space layout
randomization for shared objects, stack, heap and vdso.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Tony Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The r1 value is set based on the r0 value as we return to user space.
So tracing tools won't automatically see the right value. Fix this by
generating the correct r1 value in do_syscall_trace_exit() rather
than trying to tamper with the hot path in syscall return.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The "available_irqs" value needs to actually reflect the IRQs
available, not just start as an all-ones mask, since we only
have 32 IRQs available even on a 64-bit platform.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This may fix a reported bug where an R_TILEGX_64 in a module was not
pointing to an aligned address.
Reported-by: Simon Marchi <simon.marchi@polymtl.ca>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This change includes support for Kprobes, Jprobes and Return Probes.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Tony Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This commit adds support for static ftrace, graph function support,
and dynamic tracer support.
Signed-off-by: Tony Lu <zlu@tilera.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
