summaryrefslogtreecommitdiffstats
path: root/arch/sh
AgeCommit message (Collapse)AuthorFilesLines
2008-03-06sh: Fix up the sh64 build.Paul Mundt1-14/+7
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: Fix up SH7710 VoIP-GW build.Paul Mundt6-449/+250
The only board-specific bits that existed here were for setting up the IRQs, which are now handled by the SH7710 CPU support code instead. As there's nothing else to do for setup, kill off the board support code and have the defconfig use the generic machvec instead. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: Flag PMB support as EXPERIMENTAL.Paul Mundt1-1/+1
There's still work that needs to be done here, and this should not be enabled by default on existing boards. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: Update r7780mp defconfig.Paul Mundt1-25/+66
This disables the PMB/32BIT=y by default in r7780mp, as turning this on presently results in build errors (for an admittedly experimental feature). Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: hp6xx: Fix up hp6xx_apm build failure.Paul Mundt1-0/+2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: Fix up section mismatches.Paul Mundt2-2/+2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: hp6xx: Correct APM output.Kristoffer Ericson1-6/+14
This patch fixes the old non-verbose hp6xx apm code and enables some very basic apm output. We now get percentage (battery) output and basic time estimate. Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: update se7780 defconfiggoda.yusuke1-391/+255
This patch updates se7780_defconfig Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: replace remaining __FUNCTION__ occurrencesHarvey Harrison13-17/+17
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh: export copy-page() to modulesAndrew Morton2-0/+2
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined! like all the other architectures. Cc: Erez Zadok <ezk@cs.sunysb.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh_ksyms_32.c update for gcc 4.3Adrian Bunk1-2/+2
This patch fixes the following build error with landisk_defconfig when using gcc 4.3: <-- snip --> ... MODPOST 50 modules ERROR: "__udivsi3_i4i" [net/sunrpc/sunrpc.ko] undefined! ERROR: "__udivsi3_i4i" [net/appletalk/appletalk.ko] undefined! ERROR: "__udivsi3_i4i" [fs/ufs/ufs.ko] undefined! ERROR: "__udivsi3_i4i" [fs/ntfs/ntfs.ko] undefined! ERROR: "__sdivsi3_i4i" [fs/ntfs/ntfs.ko] undefined! ERROR: "__udivsi3_i4i" [fs/nfsd/nfsd.ko] undefined! ERROR: "__sdivsi3_i4i" [fs/nfsd/nfsd.ko] undefined! ERROR: "__udivsi3_i4i" [fs/nfs/nfs.ko] undefined! ERROR: "__udivsi3_i4i" [fs/lockd/lockd.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/usb/storage/usb-storage.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/usb/serial/pl2303.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/usb/serial/pl2303.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/usb/serial/ftdi_sio.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/usb/misc/sisusbvga/sisusbvga.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/usb/misc/sisusbvga/sisusbvga.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/media/video/v4l1-compat.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/v4l1-compat.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/usbvideo/vicam.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/media/video/usbvideo/usbvideo.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/usbvideo/usbvideo.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/media/video/sn9c102/sn9c102.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/sn9c102/sn9c102.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/se401.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/media/video/pwc/pwc.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/md/raid0.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/md/md-mod.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/md/md-mod.ko] undefined! ERROR: "__udivsi3_i4i" [drivers/md/linear.ko] undefined! ERROR: "__sdivsi3_i4i" [drivers/hid/usbhid/usbhid.ko] undefined! make[2]: *** [__modpost] Error 1 <-- snip --> Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-03-06sh/mm/pg-sh7705.c must #include <linux/fs.h>Adrian Bunk1-0/+1
This patch fixes the following compile error: <-- snip --> ... CC arch/sh/mm/pg-sh7705.o /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c: In function 'ptep_get_and_clear': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c:130: error: implicit declaration of function 'mapping_writably_mapped' make[2]: *** [arch/sh/mm/pg-sh7705.o] Error 1 <-- snip --> Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-27arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &Julia Lawall1-1/+1
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337, a bug was fixed that involved converting !x & y to !(x & y). The code below shows the same pattern, and thus should perhaps be fixed in the same way. This is not tested and clearly changes the semantics, so it is only something to consider. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ expression E1,E2; @@ ( !E1 & !E2 | - !E1 & E2 + !(E1 & E2) ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-26serial: Move asm-sh/sci.h to linux/serial_sci.h.Paul Mundt18-18/+18
This header is needed on other architectures as well (namely h8300), which currently fails to build without this in place. Rather than duplicating the port definition completely there, just move this to a common location instead. This should get h8300 working again for 2.6.25, in addition to the changes already pushed by Sato-san in -rc2. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-26sh: revert dreamcast pci changeMagnus Damm1-22/+22
Commit e036eaa681a17f71b64f6d9040fe605555623919 broke dreamcast pci, this patch fixes that by reverting the dreamcast specific bits. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-26sh: fix rtc_resources setup for sh770xRafael Ignacio Zurita1-3/+3
Fix the RTC resources setup for sh770x. Whit these proper start values RTC driver (drivers/rtc/rtc-sh.c) works. Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-26sh: heartbeat: ioremap is expected to succeedRoel Kluin1-1/+1
ioremap is expected to succeed Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-26sh: Storage class should be before const qualifierTobias Klauser1-2/+2
The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-25sh: SH5-103 needs to select CPU_SH5.Paul Mundt1-0/+1
Without this, it's possible to have CONFIG_SUPERH32=y set on SH5-103 parts, which leads to much build badness. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-25sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.Paul Mundt1-2/+2
drivers/char/pcmcia/synclink_cs.c:284:1: warning: "CCR3" redefined In file included from include/asm/cache.h:13, from include/asm/processor_32.h:15, from include/asm/processor.h:60, from include/linux/prefetch.h:14, from include/linux/list.h:8, from include/linux/module.h:9, from drivers/char/pcmcia/synclink_cs.c:38: include/asm/cpu/cache.h:38:1: warning: this is the location of the previous definition Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Fix multiple UTLB hit on UP SH-4.Hideo Saito1-0/+8
This acts as a reversion of 1c6b2ca5e0939bf8b5d1a11f1646f25189ecd447 in the case of UP SH-4, where we still have the risk of a multiple hit between the slow and fast paths. As seen on SH7780. Signed-off-by: Hideo Saito <saito@densan.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: fix pci io access for r2d boardsMagnus Damm1-1/+2
Use generic_io_base to point out the pci io window, and make sure the highest port address used is SH7751_PCI_IO_SIZE - 1. This patch fixes pci io port access for the r2d boards - CONFIG_8139TOO_PIO now works as expected. So does the alsa driver for CMI8738. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Katsuya MATSUBARA <matsu@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: use ctrl_in/out for on chip pci accessMagnus Damm6-37/+37
This patch makes sure ctrl_inN/outN are used instead of inN/outN for on chip pci registers. Without this patch addresses may be adjusted using the value in generic_io_base. This patch makes it possible to set generic_io_base and have pci without reading and writing all over the place. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Katsuya MATSUBARA <matsu@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Kill off more dead symbols.Paul Mundt5-40/+17
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: __uncached_start only on sh32.Paul Mundt1-0/+2
sh64 doesn't provide __uncached_start, so don't reference it unconditionally. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Get SH-5 caches working again post-unification.Paul Mundt2-643/+439
A number of cleanups to get the SH-5 cache management code in line with the rest of the SH backend. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Kill off bogus SH_SDK7780_STANDALONE symbol.Paul Mundt1-7/+0
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Shut up some trivial build warnings.Paul Mundt3-19/+18
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Update SH-5 flush_cache_sigtramp() for API changes.Paul Mundt1-3/+5
Previously this took an explicit range, update this to use the same behaviour as the rest of the SH parts where we simply flush out a line from the start address. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Disable big endian for SH-5.Paul Mundt1-0/+1
All SH-5 machines are little endian. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Symbol exports for trapped I/O.Paul Mundt1-0/+5
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Clean up whitespace damage in Kconfig.debug.Paul Mundt1-2/+2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Use max_t in io_trapped.Paul Mundt1-3/+5
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: add support for sh7366 processorMagnus Damm7-3/+203
This patch adds sh7366 cpu supports. Just the most basic things like interrupt controller, clocks and serial port are included at this point. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: remove maskreg irq codeMagnus Damm3-97/+0
This patch removes the maskreg irq code since it is not in use anymore. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: fix ptrace copy_from/to_user() compilation errorMagnus Damm1-2/+2
This patch makes the 32-bit ptrace code compile again. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: trapped io support for highlander V2Magnus Damm2-31/+17
This patch converts the highlander CF device from good old machvec readb/writeb to the new shiny trapped io. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: trapped io support for r2d V2Magnus Damm2-31/+15
This patch converts the CF device on r2d boards from machvec readb/writeb to trapped io. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: trapped io support V2Magnus Damm8-38/+330
The idea is that we want to get rid of the in/out/readb/writeb callbacks from the machvec and replace that with simple inline read and write operations to memory. Fast and simple for most hardware devices (think pci). Some devices require special treatment though - like 16-bit only CF devices - so we need to have some method to hook in callbacks. This patch makes it possible to add a per-device trap generating filter. This way we can get maximum performance of sane hardware - which doesn't need this filter - and crappy hardware works but gets punished by a performance hit. V2 changes things around a bit and replaces io access callbacks with a simple minimum_bus_width value. In the future we can add stride as well. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: update r2d defconfigs with usb, spi and rtcMagnus Damm2-150/+530
Update the defconfigs for r2d-plus and r2d-1 since we now have new drivers for sm501 usb, spi-over-sci and epson r9701 rtc in mainline. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: use opcode_t and enable unaligned code for sh2aMagnus Damm1-34/+25
This patch converts the unaligned access handling code to use opcode_t instead of u16. While at it, enable unaligned access handling for sh2a. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: add byte support to the sign extension codeMagnus Damm1-1/+11
This patch adds byte support to the sign extension code. Unaligned access traps should never be generated on 8-bit io operations, but we will use this code for trapped io and we do need byte support there. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: fix xtime_lock deadlocking.Peter Zijlstra2-18/+32
move update_process_times() out from under xtime_lock. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Add mach-type entries for MigoR and SDK7780.Paul Mundt1-0/+2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: migor board supportMagnus Damm5-0/+894
This patch adds basic support for the Migo-R board. Only simple stuff provided by the cpu specific sh7722 code is in place now, like serial console port, timers and usb gadget. There is also partial support for the smc91c111 ethernet controller - unfortunately some driver header file also needs patching (not included here) to make the driver get IRQ sense information from the platform data. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: Wire up new timerfd syscalls.Paul Mundt2-2/+6
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: break out unaligned sign extension codeMagnus Damm1-45/+23
Break out the sign extension code since it's used in multiple places. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: add probe support for new sh7722 cutMagnus Damm1-1/+1
This patch adds support for sh7722 devices with prr value 0xa1. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: add sh7722 support to EARLY_SCIF_CONSOLEMagnus Damm1-0/+1
This patch adds the base address of SCIF0 in the case of sh7722. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-02-14sh: remove unneeded castStephen Rothwell1-1/+1
now that platform_device_register_simple() takes a "const chat *". Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-21 10:02:52 +0000