| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The secondary CPU start C routine uses nodat_stack as a
interim stack before finally switching to kernel_stack.
Such scheme is superfluous, since the assembler restart
interrupt handler (that secondary CPU starter is called
from) does not need to use any stack for switching into
DAT mode. Once DAT is on, any stack including virtually-
mapped one could be used.
Avoid the use of nodat_stack and smp_start_secondary()
helper. Instead, initiate kernel_stack directly from
the restart interrupt handler.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The restart interrupt is triggered whenever a secondary CPU is
brought online, a remote function call dispatched from another
CPU or a manual PSW restart is initiated and causes the system
to kdump. The handling routine is always called with DAT turned
off. It then initializes the stack frame and invokes a callback.
The existing callbacks handle DAT as follows:
* __do_restart() and __machine_kexec() turn in on upon entry;
* __ipl_run(), __reipl_run() and __dump_run() do not turn it
right away, but all of them call diag308() - which turns DAT
on, but only if kasan is enabled;
In addition to the described complexity all callbacks (and the
functions they call) should avoid kasan instrumentation while
DAT is off.
This update enables DAT in the assembler restart handler and
relieves any callbacks (which are mostly C functions) from
dealing with DAT altogether.
There are four types of CPU restart that initialize control
registers in different ways:
1. Start of secondary CPU on boot - control registers are
inherited from the IPL CPU;
2. Restart of online CPU - control registers of the CPU being
restarted are kept;
3. Hotplug of offline CPU - control registers are inherited
from the starting CPU;
4. Start of offline CPU triggered by manual PSW restart -
the control registers are read from the absolute lowcore
and contain the boot time IPL CPU values updated with all
follow-up calls of smp_ctl_set_bit() and smp_ctl_clear_bit()
routines;
In first three cases contents of the control registers is the
most recent. In the latter case control registers are good
enough to facilitate successful completion of kdump operation.
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Ingo Franzki reported that our defconfig and debug_config went out of
sync with respect to DM_INTEGRITY. Fix it.
Reported-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Generate kvm hypercall functions with a macro instead of duplicating
the more or less identical code seven times. This also reduces number
of lines of code.
However the main purpose is to get rid of as many as possible open
coded error prone register asm constructs in s390 architecture code.
For the only user of kvm_hypercall identical code is created
before/after this patch (drivers/s390/virtio/virtio_ccw.c).
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20210713145713.2815167-1-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Add tracing of interactions between the SCLP base driver, firmware and
other drivers to support problem determination in case of SCLP-related
issues.
For that purpose this patch introduces two new s390dbf debug areas:
- sclp: An abbreviated log of all common interactions
- sclp_err: A full log of failed or abnormal interactions
Tracing of full SCCB contents can be enabled for the sclp area by
setting its debug level to maximum (6).
Overview of added trace events:
* Firmware interaction:
- SRV1: Service call about to be issued
- SRV2: Service call was issued
- INT: Interrupt received
* Driver interaction:
- RQAD: Request was added
- RQOK: Request success
- RQAB: Request aborted
- RQTM: Request timed out
- REG: Event listener registered
- UREG: Event listener unregistered
- EVNT: Event callback
- STCG: State-change callback
* Abnormal events:
- TMO: A timeout occurred
- UNEX: Unexpected SCCB completion
* Other (not traced at default level):
- SYN1: Synchronous wait start
- SYN2: Synchronous wait end
Since the SCLP interface is used by console drivers this patch also
moves s390dbf printks outside the critical section protected by debug
area locks to prevent a potential deadlock that would otherwise be
introduced between console_owner --> sclp_lock --> sclp_debug.lock.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Debug areas can currently only be used after s390dbf initialization
which occurs as a postcore_initcall. This is too late for tracing
earlier code such as that related to console_init().
This patch introduces a macro for defining a statically initialized
debug area that can be used to trace very early code. The macro is made
available for built-in code only because modules are never running
during early boot.
Example usage:
1. Define static debug area:
DEFINE_STATIC_DEBUG_INFO(my_debug, "my_debug", 4, 1, 16,
&debug_hex_ascii_view);
2. Add trace entry:
debug_event(&my_debug, 0, "DATA", 4);
Note: The debug area is automatically registered in debugfs during boot.
A driver must not call any of the debug_register()/_unregister()
functions on a static debug_info_t!
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Any previously recorded s390dbf debug data is reset when a debug area
is resized using the 'pages' sysfs attribute. This can make
live-debugging unnecessarily complex.
Fix this by copying existing debug data to the newly allocated debug
area when resizing.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Avoid that the "restart_part2" label, which is in the middle of a
function, appears in /proc/kallsyms.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In case of splitting to 4k mapping the early exit in walk_pte_level()
must only be taken iff flags is equal to SET_MEMORY_4K.
Currently the early exit is taken if the flag is set, and also others
might be set. This may lead to the situation that a mapping is split
but other changes are not done, like e.g. setting pages to R/W.
There is currently no such caller, but there might be in the future.
Fixes: b3e1a00c8fa4 ("s390/mm: implement set_memory_4k()")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Rename amod31 to amode31 like it was supposed to be.
Fixes: c78d0c7484f0 ("s390: rename dma section to amode31")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Both are no longer used since the conversion to generic
entry, therefore remove them.
Fixes: 56e62a737028 ("s390: convert to generic entry")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently zpci_dma_init_device()/zpci_dma_exit_device() is called as
part of zpci_enable_device()/zpci_disable_device() and errors for
zpci_dma_exit_device() are always ignored even if we could abort.
Improve upon this by moving zpci_dma_exit_device() out of
zpci_disable_device() and check for errors whenever we have a way to
abort the current operation. Note that for example in
zpci_event_hard_deconfigured() the device is expected to be gone so we
really can't abort and proceed even in case of error.
Similarly move the cc == 3 special case out of zpci_unregister_ioat()
and into the callers allowing to abort when finding an already disabled
devices precludes proceeding with the operation.
While we are at it log IOAT register/unregister errors in the s390
debugfs log,
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently clp_get_state() and clp_refresh_fh() awkwardly use the
clp_list_pci() callback mechanism to find the entry for a specific FID
and update its zdev, respectively return its state.
This is both needlessly complex and means we are always going through
the entire PCI function list even if the FID has already been found.
Instead lets introduce a clp_find_pci() function to find a specific
entry and share the CLP List PCI request handling code with
clp_list_pci().
With that in place we can also easily make the function handle a simple
out parameter instead of directly altering the zdev allowing easier
access to the updated function handle by the caller.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Instead of always treating CLP_RC_SETPCIFN_ALRDY as success and blindly
updating the function handle restrict this special handling to the
disable case by moving it into zpci_disable_device() and still treating
it as an error while also updating the function handle such that
a subsequent zpci_disable_device() succeeds or the caller can ignore the
error when aborting is not an option such as for zPCI event 0x304.
Also print this occurrence to the log such that an admin can tell why
a disable operation returned an error.
A mismatch between the state of the underlying device and our view of it
can naturally happen when the device suddenly enters the error state but
we haven't gotten the error notification yet, it must not happen on
enable though.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently clp_set_pci_fn() always returns 0 as long as the CLP request
itself succeeds even if the operation itself returns a response code
other than CLP_RC_OK or CLP_RC_SETPCIFN_ALRDY. This is highly misleading
because calling code assumes that a zero rc means that the operation was
successful.
Fix this by returning the response code or cc on failure with the
exception of the special handling for CLP_RC_SETPCIFN_ALRDY. Also let's
not assume that the returned function handle for CLP_RC_SETPCIFN_ALRDY
is 0, we don't need it anyway.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Move offsetting all of vmlinux_info fields to a separate
function for better readability.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
It is currently possible to initialize a large PMD page when
the address is not aligned on page boundary.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On failure to register a struct zpci_dev with a struct zpci_bus we left
a dangling pointer in zdev->zbus. As zpci_create_device() bails if
zpci_bus_device_register() fails this is of no consequence but still bad
practice.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
It's currently safe to call zpci_cleanup_bus_resources() even if the
resources were never created but it makes no sense so check
zdev->has_resources before we call zpci_cleanup_bus_resources() in
zpci_release_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
notification
It was pointed out during an unrelated patch review that locks should not
be open coded - i.e., writing the algorithm of a standard lock in a
function instead of using a lock from the standard library. The setting and
testing of a busy flag and sleeping on a wait_event is the same thing
a lock does. The open coded locks are invisible to lockdep, so potential
locking problems are not detected.
This patch removes the open coded locks used during
VFIO_GROUP_NOTIFY_SET_KVM notification. The busy flag
and wait queue were introduced to resolve a possible circular locking
dependency reported by lockdep when starting a secure execution guest
configured with AP adapters and domains. Reversing the order in which
the kvm->lock mutex and matrix_dev->lock mutex are locked resolves the
issue reported by lockdep, thus enabling the removal of the open coded
locks.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20210823212047.1476436-3-akrowiak@linux.ibm.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The function pointer to the interception handler for the PQAP instruction
can get changed during the interception process. Let's add a
semaphore to struct kvm_s390_crypto to control read/write access to the
function pointer contained therein.
The semaphore must be locked for write access by the vfio_ap device driver
when notified that the KVM pointer has been set or cleared. It must be
locked for read access by the interception framework when the PQAP
instruction is intercepted.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20210823212047.1476436-2-akrowiak@linux.ibm.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Add new types of KVM stats, linear and logarithmic histogram.
Histogram are very useful for observing the value distribution
of time or size related stats.
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210802165633.1866976-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Ship minimal stdarg.h (1 type, 4 macros) as <linux/stdarg.h>.
stdarg.h is the only userspace header commonly used in the kernel.
GPL 2 version of <stdarg.h> can be extracted from
http://archive.debian.org/debian/pool/main/g/gcc-4.2/gcc-4.2_4.2.4.orig.tar.gz
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20fe
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Fixes: 05bc1be6db4b2 ("s390/pci: create zPCI bus")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The memory block occupied by the SCLP early buffer that is allocated
by the decompressor and then handed over to the decompressed kernel,
must be reserved to prevent it from being reused for other purposes.
This is necessary because the SCLP early buffer is still in use
during kernel initialization.
Fixes: f1d3c5323772 ("s390/boot: move sclp early buffer from fixed address in asm to C")
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The last user of arch_set_page_states(), arch_set_page_nodat() and
arch_test_page_nodat() was removed in commit 394216275c7d
("s390: remove broken hibernate / power management support"),
let's remove these functions.
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20210806075430.6103-1-david@redhat.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Neither of the two drivers provides any SLIB parameter data, so get rid
of the dead code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Make architectures select TRACE_IRQFLAGS_SUPPORT instead of
having many defines.
Link: https://lkml.kernel.org/r/20210731052233.4703-2-masahiroy@kernel.org
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> #arch/arc
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
The PCI core already ensures that the MSI[-X] state is correct when MSI[-X]
is disabled. For MSI the reset state is all entries unmasked and for MSI-X
all vectors are masked.
S390 masks all MSI entries and masks the already masked MSI-X entries
again. Remove it and let the device in the correct state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20210729222542.939798136@linutronix.de
|
|
Setting the ->dma_address to DMA_MAPPING_ERROR is not part of
the ->map_sg calling convention, so remove it.
Link: https://lore.kernel.org/linux-mips/20210716063241.GC13345@lst.de/
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The .map_sg() op now expects an error code instead of zero on failure.
So propagate the error from __s390_dma_map_sg() up. __s390_dma_map_sg()
returns either -ENOMEM on allocation failure or -EINVAL which is
the same as what's expected by dma_map_sgtable().
Signed-off-by: Martin Oliveira <martin.oliveira@eideticom.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We need the driver core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lru_slot is used to keep track of the index of the most-recently used
memslot. The correct acronym would be "mru" but that is not a common
acronym. So call it last_used_slot which is a bit more obvious.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210804222844.1419481-2-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df9322 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098ed ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df9322 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- fix zstd build for -march=z900 (undefined reference to __clzdi2)
- add missing .got.plts to vdso linker scripts to fix kpatch build
errors
- update defconfigs
* tag 's390-5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/boot: fix zstd build for -march=z900
s390/vdso: add .got.plt in vdso linker script
|
|
The dma section name is confusing, since the code which resides within
that section has nothing to do with direct memory access. Instead the
limitation is that the code has to run in 31 bit addressing mode, and
therefore has to reside below 2GB. So the name was chosen since
ZONE_DMA is the same region.
To reduce confusion rename the section to amode31, which hopefully
describes better what this is about.
Note: this will also change vmcoreinfo strings
- SDMA=... gets renamed to SAMODE31=...
- EDMA=... gets renamed to EAMODE31=...
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-5-bigeasy@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
s390 allows hotpatching the mask of a conditional jump instruction.
Make use of this feature in order to avoid the expensive stop_machine()
call.
The new trampolines are split in 3 stages:
- A first stage is a 6-byte relative conditional long branch located at
each function's entry point. Its offset always points to the second
stage for the corresponding function, and its mask is either all 0s
(ftrace off) or all 1s (ftrace on). The code for flipping the mask is
borrowed from ftrace_{enable,disable}_ftrace_graph_caller. After
flipping, ftrace_arch_code_modify_post_process() syncs with all the
other CPUs by sending SIGPs.
- Second stages for vmlinux are stored in a separate part of the .text
section reserved by the linker script, and in dynamically allocated
memory for modules. This prevents the icache pollution. The total
size of second stages is about 1.5% of that of the kernel image.
Putting second stages in the .bss section is possible and decreases
the size of the non-compressed vmlinux, but splits the kernel 1:1
mapping, which is a bad tradeoff.
Each second stage contains a call to the third stage, a pointer to
the part of the intercepted function right after the first stage, and
a pointer to an interceptor function (e.g. ftrace_caller).
Second stages are 8-byte aligned for the future direct calls
implementation.
- There are only two copies of the third stage: in the .text section
for vmlinux and in dynamically allocated memory for modules. It can be
an expoline, which is relatively large, so inlining it into each
second stage is prohibitively expensive.
As a result of this organization, phoronix-test-suite with ftrace off
does not show any performance degradation.
Suggested-by: Sven Schnelle <svens@linux.ibm.com>
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Co-developed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/r/20210728212546.128248-3-iii@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Conflicting commits, all resolutions pretty trivial:
drivers/bus/mhi/pci_generic.c
5c2c85315948 ("bus: mhi: pci-generic: configurable network interface MRU")
56f6f4c4eb2a ("bus: mhi: pci_generic: Apply no-op for wake using sideband wake boolean")
drivers/nfc/s3fwrn5/firmware.c
a0302ff5906a ("nfc: s3fwrn5: remove unnecessary label")
46573e3ab08f ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
801e541c79bb ("nfc: s3fwrn5: fix undefined parameter values in dev_err()")
MAINTAINERS
7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
8a7b46fa7902 ("MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.14-rc4, including fixes from bpf, can, WiFi
(mac80211) and netfilter trees.
Current release - regressions:
- mac80211: fix starting aggregation sessions on mesh interfaces
Current release - new code bugs:
- sctp: send pmtu probe only if packet loss in Search Complete state
- bnxt_en: add missing periodic PHC overflow check
- devlink: fix phys_port_name of virtual port and merge error
- hns3: change the method of obtaining default ptp cycle
- can: mcba_usb_start(): add missing urb->transfer_dma initialization
Previous releases - regressions:
- set true network header for ECN decapsulation
- mlx5e: RX, avoid possible data corruption w/ relaxed ordering and
LRO
- phy: re-add check for PHY_BRCM_DIS_TXCRXC_NOENRGY on the BCM54811
PHY
- sctp: fix return value check in __sctp_rcv_asconf_lookup
Previous releases - always broken:
- bpf:
- more spectre corner case fixes, introduce a BPF nospec
instruction for mitigating Spectre v4
- fix OOB read when printing XDP link fdinfo
- sockmap: fix cleanup related races
- mac80211: fix enabling 4-address mode on a sta vif after assoc
- can:
- raw: raw_setsockopt(): fix raw_rcv panic for sock UAF
- j1939: j1939_session_deactivate(): clarify lifetime of session
object, avoid UAF
- fix number of identical memory leaks in USB drivers
- tipc:
- do not blindly write skb_shinfo frags when doing decryption
- fix sleeping in tipc accept routine"
* tag 'net-5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
gve: Update MAINTAINERS list
can: esd_usb2: fix memory leak
can: ems_usb: fix memory leak
can: usb_8dev: fix memory leak
can: mcba_usb_start(): add missing urb->transfer_dma initialization
can: hi311x: fix a signedness bug in hi3110_cmd()
MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver
bpf: Fix leakage due to insufficient speculative store bypass mitigation
bpf: Introduce BPF nospec instruction for mitigating Spectre v4
sis900: Fix missing pci_disable_device() in probe and remove
net: let flow have same hash in two directions
nfc: nfcsim: fix use after free during module unload
tulip: windbond-840: Fix missing pci_disable_device() in probe and remove
sctp: fix return value check in __sctp_rcv_asconf_lookup
nfc: s3fwrn5: fix undefined parameter values in dev_err()
net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32
net/mlx5e: Fix nullptr in mlx5e_hairpin_get_mdev()
net/mlx5: Unload device upon firmware fatal error
net/mlx5e: Fix page allocation failure for ptp-RQ over SF
net/mlx5e: Fix page allocation failure for trap-RQ over SF
...
|
|
Currently, the install target in arch/s390/Makefile descends into
arch/s390/boot/Makefile to invoke the shell script, but there is no
good reason to do so.
arch/s390/Makefile can run the shell script directly.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210729142338.446002-1-masahiroy@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
s390x GCC and SystemZ Clang have ThreadSanitizer support now [1] [2],
so enable KCSAN for s390.
[1] https://gcc.gnu.org/git/?p=gcc.git;a=commit;h=ea22954e7c58
[2] https://reviews.llvm.org/D105629
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20210728190254.3921642-5-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
[hca@linux.ibm.com: simplify/rework code]
Link: https://lore.kernel.org/r/20210728190254.3921642-4-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Implement set_memory_4k() which will split any present large or huge
mapping in the given range to a 4k mapping.
Link: https://lore.kernel.org/r/20210728190254.3921642-2-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
zstd decompression uses __builtin_clz() which fails back to __clzdi2()
when the kernel is built for older hardware like z900. This leads to
build failures like the following:
s390x-11.1.0-ld: /devel/src/kernel/arch/s390/boot/compressed/../../../../lib/zstd/bitstream.h:148: undefined reference to `__clzdi2'
Fix that by optionally including lib/clz_ctz.c into the decompressor.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 7b034d9c1b08 ("s390/boot: add zstd support")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/patch-1.thread-f0f589.git-f0f58936888f.your-ad-here.call-01627564869-ext-2765@work.hours
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
KCFLAGS="-mno-pic-data-is-text-relative" make leads to bfd assertion
error in s390_got_pointer():
LD arch/s390/kernel/vdso64/vdso64.so.dbg
ld: BFD version 2.35-18.fc33 assertion fail elf-s390-common.c:74
readelf -Wr vdso64_generic.o | grep GOT
0000000000000032 000000110000001a R_390_GOTENT 0000000000000000 _vdso_data + 2
(...)
Add .got.plt in linker script to avoid this.
Suggested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
