summaryrefslogtreecommitdiffstats
path: root/arch/riscv/kernel
AgeCommit message (Collapse)AuthorFilesLines
2020-01-31Merge tag 'riscv-for-linus-5.6-mw0' of ↵Linus Torvalds4-0/+11
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V updates from Palmer Dabbelt: "This contains a handful of patches for this merge window: - Support for kasan - 32-bit physical addresses on rv32i-based systems - Support for CONFIG_DEBUG_VIRTUAL - DT entry for the FU540 GPIO controller, which has recently had a device driver merged These boot a buildroot-based system on QEMU's virt board for me" * tag 'riscv-for-linus-5.6-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: dts: Add DT support for SiFive FU540 GPIO driver riscv: mm: add support for CONFIG_DEBUG_VIRTUAL riscv: keep 32-bit kernel to 32-bit phys_addr_t kasan: Add riscv to KASAN documentation. riscv: Add KASAN support kasan: No KASAN's memmove check if archs don't have it.
2020-01-29Merge tag 'tty-5.6-rc1' of ↵Linus Torvalds1-4/+0
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here are the big set of tty and serial driver updates for 5.6-rc1 Included in here are: - dummy_con cleanups (touches lots of arch code) - sysrq logic cleanups (touches lots of serial drivers) - samsung driver fixes (wasn't really being built) - conmakeshash move to tty subdir out of scripts - lots of small tty/serial driver updates All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits) tty: n_hdlc: Use flexible-array member and struct_size() helper tty: baudrate: SPARC supports few more baud rates tty: baudrate: Synchronise baud_table[] and baud_bits[] tty: serial: meson_uart: Add support for kernel debugger serial: imx: fix a race condition in receive path serial: 8250_bcm2835aux: Document struct bcm2835aux_data serial: 8250_bcm2835aux: Use generic remapping code serial: 8250_bcm2835aux: Allocate uart_8250_port on stack serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER serial: 8250_bcm2835aux: Fix line mismatch on driver unbind serial_core: Remove unused member in uart_port vt: Correct comment documenting do_take_over_console() vt: Delete comment referencing non-existent unbind_con_driver() arch/xtensa/setup: Drop dummy_con initialization arch/x86/setup: Drop dummy_con initialization arch/unicore32/setup: Drop dummy_con initialization arch/sparc/setup: Drop dummy_con initialization arch/sh/setup: Drop dummy_con initialization arch/s390/setup: Drop dummy_con initialization ...
2020-01-28Merge branch 'sched-core-for-linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler updates from Ingo Molnar: "These were the main changes in this cycle: - More -rt motivated separation of CONFIG_PREEMPT and CONFIG_PREEMPTION. - Add more low level scheduling topology sanity checks and warnings to filter out nonsensical topologies that break scheduling. - Extend uclamp constraints to influence wakeup CPU placement - Make the RT scheduler more aware of asymmetric topologies and CPU capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y - Make idle CPU selection more consistent - Various fixes, smaller cleanups, updates and enhancements - please see the git log for details" * 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits) sched/fair: Define sched_idle_cpu() only for SMP configurations sched/topology: Assert non-NUMA topology masks don't (partially) overlap idle: fix spelling mistake "iterrupts" -> "interrupts" sched/fair: Remove redundant call to cpufreq_update_util() sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP sched/fair: calculate delta runnable load only when it's needed sched/cputime: move rq parameter in irqtime_account_process_tick stop_machine: Make stop_cpus() static sched/debug: Reset watchdog on all CPUs while processing sysrq-t sched/core: Fix size of rq::uclamp initialization sched/uclamp: Fix a bug in propagating uclamp value in new cgroups sched/fair: Load balance aggressively for SCHED_IDLE CPUs sched/fair : Improve update_sd_pick_busiest for spare capacity case watchdog: Remove soft_lockup_hrtimer_cnt and related code sched/rt: Make RT capacity-aware sched/fair: Make EAS wakeup placement consider uclamp restrictions sched/fair: Make task_fits_capacity() consider uclamp restrictions sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with() sched/uclamp: Make uclamp util helpers use and return UL values ...
2020-01-22riscv: Add KASAN supportNick Hu4-0/+11
This patch ports the feature Kernel Address SANitizer (KASAN). Note: The start address of shadow memory is at the beginning of kernel space, which is 2^64 - (2^39 / 2) in SV39. The size of the kernel space is 2^38 bytes so the size of shadow memory should be 2^38 / 8. Thus, the shadow memory would not overlap with the fixmap area. There are currently two limitations in this port, 1. RV64 only: KASAN need large address space for extra shadow memory region. 2. KASAN can't debug the modules since the modules are allocated in VMALLOC area. We mapped the shadow memory, which corresponding to VMALLOC area, to the kasan_early_shadow_page because we don't have enough physical space for all the shadow memory corresponding to VMALLOC area. Signed-off-by: Nick Hu <nickhu@andestech.com> Reported-by: Greentime Hu <green.hu@gmail.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-01-18riscv: delete temporary filesIlie Halip1-1/+2
Temporary files used in the VDSO build process linger on even after make mrproper: vdso-dummy.o.tmp, vdso.so.dbg.tmp. Delete them once they're no longer needed. Signed-off-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2020-01-15riscv: make sure the cores stay looping in .Lsecondary_parkGreentime Hu1-6/+10
The code in secondary_park is currently placed in the .init section. The kernel reclaims and clears this code when it finishes booting. That causes the cores parked in it to go to somewhere unpredictable, so we move this function out of init to make sure the cores stay looping there. The instruction bgeu a0, t0, .Lsecondary_park may have "a relocation truncated to fit" issue during linking time. It is because that sections are too far to jump. Let's use tail to jump to the .Lsecondary_park. Signed-off-by: Greentime Hu <greentime.hu@sifive.com> Reviewed-by: Anup Patel <anup.patel@sifive.com> Cc: Andreas Schwab <schwab@suse.de> Cc: stable@vger.kernel.org Fixes: 76d2a0493a17d ("RISC-V: Init and Halt Code") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2020-01-14arch/riscv/setup: Drop dummy_con initializationArvind Sankar1-4/+0
con_init in tty/vt.c will now set conswitchp to dummy_con if it's unset. Drop it from arch setup code. Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Link: https://lore.kernel.org/r/20191218214506.49252-19-nivedita@alum.mit.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-12Merge tag 'riscv/for-v5.5-rc6' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Paul Walmsley: "Two fixes for RISC-V: - Clear FP registers during boot when FP support is present, rather than when they aren't present - Move the header files associated with the SiFive L2 cache controller to drivers/soc (where the code was recently moved)" * tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: Fixup obvious bug for fp-regs reset riscv: move sifive_l2_cache.h to include/soc
2020-01-12riscv: Fixup obvious bug for fp-regs resetGuo Ren1-1/+1
CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine ISA Register misa. Every bit:1 indicate a feature, so we should beqz reset_done when there is no F/D bit in csr_misa register. Signed-off-by: Guo Ren <ren_guo@c-sky.com> [paul.walmsley@sifive.com: fix typo in commit message] Fixes: 9e80635619b51 ("riscv: clear the instruction cache and all registers when booting") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2020-01-07riscv: Implement copy_thread_tlsAmanieu d'Antras1-3/+3
This is required for clone3 which passes the TLS value through a struct rather than a register. Signed-off-by: Amanieu d'Antras <amanieu@gmail.com> Cc: linux-riscv@lists.infradead.org Cc: <stable@vger.kernel.org> # 5.3.x Link: https://lore.kernel.org/r/20200102172413.654385-6-amanieu@gmail.com Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
2020-01-04riscv: prefix IRQ_ macro names with an RV_ namespacePaul Walmsley1-3/+3
"IRQ_TIMER", used in the arch/riscv CSR header file, is a sufficiently generic macro name that it's used by several source files across the Linux code base. Some of these other files ultimately include the arch/riscv CSR include file, causing collisions. Fix by prefixing the RISC-V csr.h IRQ_ macro names with an RV_ prefix. Fixes: a4c3733d32a72 ("riscv: abstract out CSR names for supervisor vs machine mode") Reported-by: Olof Johansson <olof@lixom.net> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2020-01-03riscv: ftrace: correct the condition logic in function graph tracerZong Li1-1/+1
The condition should be logical NOT to assign the hook address to parent address. Because the return value 0 of function_graph_enter upon success. Fixes: e949b6db51dc (riscv/function_graph: Simplify with function_graph_enter()) Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: stable@vger.kernel.org Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-12-27riscv: reject invalid syscalls below -1David Abdurachmanov1-0/+1
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops with "Unable to handle kernel paging request at virtual address" message. This happens when enosys stressor starts testing random non-valid syscalls. I forgot to redirect any syscall below -1 to sys_ni_syscall. With the patch kernel oops messages are gone while running stress-ng enosys stressor. Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Fixes: 5340627e3fe0 ("riscv: add support for SECCOMP and SECCOMP_FILTER") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-12-27riscv: fix compile failure with EXPORT_SYMBOL() & !MMULuc Van Oostenryck1-3/+0
When support for !MMU was added, the declaration of __asm_copy_to_user() & __asm_copy_from_user() were #ifdefed out hence their EXPORT_SYMBOL() give an error message like: .../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here .../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here Since these symbols are not defined with !MMU it's wrong to export them. Same for __clear_user() (even though this one is also declared in include/asm-generic/uaccess.h and thus doesn't give an error message). Fix this by doing the EXPORT_SYMBOL() directly where these symbols are defined: inside lib/uaccess.S itself. Fixes: 6bd33e1ece52 ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU") Reported-by: kbuild test robot <lkp@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-12-25Merge tag 'v5.5-rc3' into sched/core, to pick up fixesIngo Molnar1-1/+1
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-12-20riscv: fix scratch register clearing in M-mode.Greentime Hu1-1/+1
This patch fixes that the sscratch register clearing in M-mode. It cleared sscratch register in M-mode, but it should clear mscratch register. That will cause kernel trap if the CPU core doesn't support S-mode when trying to access sscratch. Fixes: 9e80635619b5 ("riscv: clear the instruction cache and all registers when booting") Signed-off-by: Greentime Hu <greentime.hu@sifive.com> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-12-08sched/rt, riscv: Use CONFIG_PREEMPTIONThomas Gleixner1-2/+2
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT. Both PREEMPT and PREEMPT_RT require the same functionality which today depends on CONFIG_PREEMPT. Switch the entry code over to use CONFIG_PREEMPTION. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # for arch/riscv Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: linux-riscv@lists.infradead.org Link: https://lore.kernel.org/r/20191015191821.11479-17-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-11-30Merge tag 'seccomp-v5.5-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull seccomp updates from Kees Cook: "Mostly this is implementing the new flag SECCOMP_USER_NOTIF_FLAG_CONTINUE, but there are cleanups as well. - implement SECCOMP_USER_NOTIF_FLAG_CONTINUE (Christian Brauner) - fixes to selftests (Christian Brauner) - remove secure_computing() argument (Christian Brauner)" * tag 'seccomp-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: seccomp: rework define for SECCOMP_USER_NOTIF_FLAG_CONTINUE seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test seccomp: simplify secure_computing() seccomp: test SECCOMP_USER_NOTIF_FLAG_CONTINUE seccomp: add SECCOMP_USER_NOTIF_FLAG_CONTINUE seccomp: avoid overflow in implicit constant conversion
2019-11-27Merge tag 'riscv/for-v5.5-rc1' of ↵Linus Torvalds18-138/+340
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V updates from Paul Walmsley: "New features: - SECCOMP support - nommu support - SBI-less system support - M-Mode support - TLB flush optimizations Other improvements: - Pass the complete RISC-V ISA string supported by the CPU cores to userspace, rather than redacting parts of it in the kernel - Add platform DMA IP block data to the HiFive Unleashed board DT file - Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image compression formats, in line with other architectures Cleanups: - Remove unnecessary PTE_PARENT_SIZE macro - Standardize include guard naming across arch/riscv" * tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits) riscv: provide a flat image loader riscv: add nommu support riscv: clear the instruction cache and all registers when booting riscv: read the hart ID from mhartid on boot riscv: provide native clint access for M-mode riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00 riscv: add support for MMIO access to the timer registers riscv: implement remote sfence.i using IPIs riscv: cleanup the default power off implementation riscv: poison SBI calls for M-mode riscv: don't allow selecting SBI based drivers for M-mode RISC-V: Add multiple compression image format. riscv: clean up the macro format in each header file riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE riscv: abstract out CSR names for supervisor vs machine mode riscv: separate MMIO functions into their own header file riscv: enter WFI in default_power_off() if SBI does not shutdown RISC-V: Issue a tlb page flush if possible RISC-V: Issue a local tlbflush if possible. RISC-V: Do not invoke SBI call if cpumask is empty ...
2019-11-26Merge branch 'x86-asm-for-linus' of ↵Linus Torvalds1-3/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 asm updates from Ingo Molnar: "The main changes in this cycle were: - Cross-arch changes to move the linker sections for NOTES and EXCEPTION_TABLE into the RO_DATA area, where they belong on most architectures. (Kees Cook) - Switch the x86 linker fill byte from x90 (NOP) to 0xcc (INT3), to trap jumps into the middle of those padding areas instead of sliding execution. (Kees Cook) - A thorough cleanup of symbol definitions within x86 assembler code. The rather randomly named macros got streamlined around a (hopefully) straightforward naming scheme: SYM_START(name, linkage, align...) SYM_END(name, sym_type) SYM_FUNC_START(name) SYM_FUNC_END(name) SYM_CODE_START(name) SYM_CODE_END(name) SYM_DATA_START(name) SYM_DATA_END(name) etc - with about three times of these basic primitives with some label, local symbol or attribute variant, expressed via postfixes. No change in functionality intended. (Jiri Slaby) - Misc other changes, cleanups and smaller fixes" * 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits) x86/entry/64: Remove pointless jump in paranoid_exit x86/entry/32: Remove unused resume_userspace label x86/build/vdso: Remove meaningless CFLAGS_REMOVE_*.o m68k: Convert missed RODATA to RO_DATA x86/vmlinux: Use INT3 instead of NOP for linker fill bytes x86/mm: Report actual image regions in /proc/iomem x86/mm: Report which part of kernel image is freed x86/mm: Remove redundant address-of operators on addresses xtensa: Move EXCEPTION_TABLE to RO_DATA segment powerpc: Move EXCEPTION_TABLE to RO_DATA segment parisc: Move EXCEPTION_TABLE to RO_DATA segment microblaze: Move EXCEPTION_TABLE to RO_DATA segment ia64: Move EXCEPTION_TABLE to RO_DATA segment h8300: Move EXCEPTION_TABLE to RO_DATA segment c6x: Move EXCEPTION_TABLE to RO_DATA segment arm64: Move EXCEPTION_TABLE to RO_DATA segment alpha: Move EXCEPTION_TABLE to RO_DATA segment x86/vmlinux: Move EXCEPTION_TABLE to RO_DATA segment x86/vmlinux: Actually use _etext for the end of the text segment vmlinux.lds.h: Allow EXCEPTION_TABLE to live in RO_DATA ...
2019-11-25Merge tag 'printk-for-5.5' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk Pull printk updates from Petr Mladek: - Allow to print symbolic error names via new %pe modifier. - Use pr_warn() instead of the remaining pr_warning() calls. Fix formatting of the related lines. - Add VSPRINTF entry to MAINTAINERS. * tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits) checkpatch: don't warn about new vsprintf pointer extension '%pe' MAINTAINERS: Add VSPRINTF tools lib api: Renaming pr_warning to pr_warn ASoC: samsung: Use pr_warn instead of pr_warning lib: cpu_rmap: Use pr_warn instead of pr_warning trace: Use pr_warn instead of pr_warning dma-debug: Use pr_warn instead of pr_warning vgacon: Use pr_warn instead of pr_warning fs: afs: Use pr_warn instead of pr_warning sh/intc: Use pr_warn instead of pr_warning scsi: Use pr_warn instead of pr_warning platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning platform/x86: asus-laptop: Use pr_warn instead of pr_warning platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning oprofile: Use pr_warn instead of pr_warning of: Use pr_warn instead of pr_warning macintosh: Use pr_warn instead of pr_warning idsn: Use pr_warn instead of pr_warning ide: Use pr_warn instead of pr_warning crypto: n2: Use pr_warn instead of pr_warning ...
2019-11-22Merge branch 'next/nommu' into for-nextPaul Walmsley16-94/+302
Conflicts: arch/riscv/boot/Makefile arch/riscv/include/asm/sbi.h
2019-11-22Merge branch 'next/isa-string' into for-nextPaul Walmsley1-42/+3
2019-11-17riscv: add nommu supportChristoph Hellwig4-3/+34
The kernel runs in M-mode without using page tables, and thus can't run bare metal without help from additional firmware. Most of the patch is just stubbing out code not needed without page tables, but there is an interesting detail in the signals implementation: - The normal RISC-V syscall ABI only implements rt_sigreturn as VDSO entry point, but the ELF VDSO is not supported for nommu Linux. We instead copy the code to call the syscall onto the stack. In addition to enabling the nommu code a new defconfig for a small kernel image that can run in nommu mode on qemu is also provided, to run a kernel in qemu you can use the following command line: qemu-system-riscv64 -smp 2 -m 64 -machine virt -nographic \ -kernel arch/riscv/boot/loader \ -drive file=rootfs.ext2,format=raw,id=hd0 \ -device virtio-blk-device,drive=hd0 Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> [paul.walmsley@sifive.com: updated to apply; add CONFIG_MMU guards around PCI_IOBASE definition to fix build issues; fixed checkpatch issues; move the PCI_IO_* and VMEMMAP address space macros along with the others; resolve sparse warning] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-17riscv: clear the instruction cache and all registers when bootingChristoph Hellwig1-1/+87
When we get booted we want a clear slate without any leaks from previous supervisors or the firmware. Flush the instruction cache and then clear all registers to known good values. This is really important for the upcoming nommu support that runs on M-mode, but can't really harm when running in S-mode either. Vaguely based on the concepts from opensbi. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-17riscv: read the hart ID from mhartid on bootDamien Le Moal1-0/+8
When in M-Mode, we can use the mhartid CSR to get the ID of the running HART. Doing so, direct M-Mode boot without firmware is possible. Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-17riscv: provide native clint access for M-modeChristoph Hellwig5-3/+64
RISC-V has the concept of a cpu level interrupt controller. The interface for it is split between a standardized part that is exposed as bits in the mstatus/sstatus register and the mie/mip/sie/sip CRS. But the bit to actually trigger IPIs is not standardized and just mentioned as implementable using MMIO. Add support for IPIs using MMIO using the SiFive clint layout (which is also shared by Ariane, Kendryte and the Qemu virt platform). Additionally the MMIO block also supports the time value and timer compare registers, so they are also set up using the same OF node. Support for other layouts should also be relatively easy to add in the future. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> [paul.walmsley@sifive.com: update include guard format; fix checkpatch issues; minor commit message cleanup] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-13riscv: cleanup the default power off implementationChristoph Hellwig3-2/+18
Move the sbi poweroff to a separate function and file that is only compiled if CONFIG_SBI is set. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Atish Patra <atish.patra@wdc.com> [paul.walmsley@sifive.com: split the WFI fix into a separate patch] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-05riscv: abstract out CSR names for supervisor vs machine modeChristoph Hellwig10-86/+91
Many of the privileged CSRs exist in a supervisor and machine version that are used very similarly. Provide versions of the CSR names and fields that map to either the S-mode or M-mode variant depending on a new CONFIG_RISCV_M_MODE kconfig symbol. Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com> and Paul Walmsley <paul.walmsley@sifive.com>. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource, drivers/irqchip [paul.walmsley@sifive.com: updated to apply] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-05riscv: enter WFI in default_power_off() if SBI does not shutdownChristoph Hellwig1-1/+2
Provide a new default fallback power off that just sits in a wfi loop to save some power. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Atish Patra <atish.patra@wdc.com> [paul.walmsley@sifive.com: split the WFI fix apart from the nommu-related default_power_off() changes] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-11-04vmlinux.lds.h: Replace RW_DATA_SECTION with RW_DATAKees Cook1-1/+1
Rename RW_DATA_SECTION to RW_DATA. (Calling this a "section" is a lie, since it's multiple sections and section flags cannot be applied to the macro.) Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # s390 Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-c6x-dev@linux-c6x.org Cc: linux-ia64@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: Segher Boessenkool <segher@kernel.crashing.org> Cc: Will Deacon <will@kernel.org> Cc: x86-ml <x86@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: https://lkml.kernel.org/r/20191029211351.13243-14-keescook@chromium.org
2019-11-04vmlinux.lds.h: Replace RO_DATA_SECTION with RO_DATAKees Cook1-1/+1
Finish renaming RO_DATA_SECTION to RO_DATA. (Calling this a "section" is a lie, since it's multiple sections and section flags cannot be applied to the macro.) Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # s390 Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-c6x-dev@linux-c6x.org Cc: linux-ia64@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: Segher Boessenkool <segher@kernel.crashing.org> Cc: Will Deacon <will@kernel.org> Cc: x86-ml <x86@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: https://lkml.kernel.org/r/20191029211351.13243-13-keescook@chromium.org
2019-11-04vmlinux.lds.h: Move NOTES into RO_DATAKees Cook1-1/+0
The .notes section should be non-executable read-only data. As such, move it to the RO_DATA macro instead of being per-architecture defined. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # s390 Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: linux-alpha@vger.kernel.org Cc: linux-arch@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-c6x-dev@linux-c6x.org Cc: linux-ia64@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: Segher Boessenkool <segher@kernel.crashing.org> Cc: Will Deacon <will@kernel.org> Cc: x86-ml <x86@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: https://lkml.kernel.org/r/20191029211351.13243-11-keescook@chromium.org
2019-10-29riscv: add support for SECCOMP and SECCOMP_FILTERDavid Abdurachmanov2-2/+35
This patch was extensively tested on Fedora/RISCV (applied by default on top of 5.2-rc7 kernel for <2 months). The patch was also tested with 5.3-rc on QEMU and SiFive Unleashed board. libseccomp (userspace) was rebased: https://github.com/seccomp/libseccomp/pull/134 Fully passes libseccomp regression testing (simulation and live). There is one failing kernel selftest: global.user_notification_signal v1 -> v2: - return immediately if secure_computing(NULL) returns -1 - fixed whitespace issues - add missing seccomp.h - remove patch #2 (solved now) - add riscv to seccomp kernel selftest Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Cc: keescook@chromium.org Cc: me@carlosedp.com Tested-by: Carlos de Paula <me@carlosedp.com> Reviewed-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/linux-riscv/CAEn-LTp=ss0Dfv6J00=rCAy+N78U2AmhqJNjfqjr2FDpPYjxEQ@mail.gmail.com/ Link: https://lore.kernel.org/linux-riscv/CAJr-aD=UnCN9E_mdVJ2H5nt=6juRSWikZnA5HxDLQxXLbsRz-w@mail.gmail.com/ [paul.walmsley@sifive.com: cleaned up Cc: lines; fixed spelling and checkpatch issues; updated to apply] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-28RISC-V: Remove unsupported isa string info printAtish Patra1-42/+3
/proc/cpuinfo should just print all the isa string as an information instead of determining what is supported or not. ELF hwcap can be used by the userspace to figure out that. Simplify the isa string printing by removing the unsupported isa string print and all related code. The relevant discussion can be found at http://lists.infradead.org/pipermail/linux-riscv/2019-September/006702.html Signed-off-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: http://lists.infradead.org/pipermail/linux-riscv/2019-September/006702.html Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-28riscv: for C functions called only from assembly, mark with __visiblePaul Walmsley5-8/+8
Rather than adding prototypes for C functions called only by assembly code, mark them as __visible. This avoids adding prototypes that will never be used by the callers. Resolves the following sparse warnings: arch/riscv/kernel/irq.c:27:29: warning: symbol 'do_IRQ' was not declared. Should it be static? arch/riscv/kernel/ptrace.c:151:6: warning: symbol 'do_syscall_trace_enter' was not declared. Should it be static? arch/riscv/kernel/ptrace.c:165:6: warning: symbol 'do_syscall_trace_exit' was not declared. Should it be static? arch/riscv/kernel/signal.c:295:17: warning: symbol 'do_notify_resume' was not declared. Should it be static? arch/riscv/kernel/traps.c:92:1: warning: symbol 'do_trap_unknown' was not declared. Should it be static? arch/riscv/kernel/traps.c:94:1: warning: symbol 'do_trap_insn_misaligned' was not declared. Should it be static? arch/riscv/kernel/traps.c:96:1: warning: symbol 'do_trap_insn_fault' was not declared. Should it be static? arch/riscv/kernel/traps.c:98:1: warning: symbol 'do_trap_insn_illegal' was not declared. Should it be static? arch/riscv/kernel/traps.c:100:1: warning: symbol 'do_trap_load_misaligned' was not declared. Should it be static? arch/riscv/kernel/traps.c:102:1: warning: symbol 'do_trap_load_fault' was not declared. Should it be static? arch/riscv/kernel/traps.c:104:1: warning: symbol 'do_trap_store_misaligned' was not declared. Should it be static? arch/riscv/kernel/traps.c:106:1: warning: symbol 'do_trap_store_fault' was not declared. Should it be static? arch/riscv/kernel/traps.c:108:1: warning: symbol 'do_trap_ecall_u' was not declared. Should it be static? arch/riscv/kernel/traps.c:110:1: warning: symbol 'do_trap_ecall_s' was not declared. Should it be static? arch/riscv/kernel/traps.c:112:1: warning: symbol 'do_trap_ecall_m' was not declared. Should it be static? arch/riscv/kernel/traps.c:124:17: warning: symbol 'do_trap_break' was not declared. Should it be static? arch/riscv/kernel/smpboot.c:136:24: warning: symbol 'smp_callin' was not declared. Should it be static? Based on a suggestion from Luc Van Oostenryck. This version includes changes based on feedback from Christoph Hellwig <hch@lst.de>. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> # for do_syscall_trace_*
2019-10-28riscv: fp: add missing __user pointer annotationsPaul Walmsley1-2/+2
The __user annotations were removed from the {save,restore}_fp_state() function signatures by commit 007f5c358957 ("Refactor FPU code in signal setup/return procedures"), but should be present, and sparse warns when they are not applied. Add them back in. This change should have no functional impact. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Fixes: 007f5c358957 ("Refactor FPU code in signal setup/return procedures") Cc: Alan Kao <alankao@andestech.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
2019-10-28riscv: add missing header file includesPaul Walmsley10-0/+12
sparse identifies several missing prototypes caused by missing preprocessor include directives: arch/riscv/kernel/cpufeature.c:16:6: warning: symbol 'has_fpu' was not declared. Should it be static? arch/riscv/kernel/process.c:26:6: warning: symbol 'arch_cpu_idle' was not declared. Should it be static? arch/riscv/kernel/reset.c:15:6: warning: symbol 'pm_power_off' was not declared. Should it be static? arch/riscv/kernel/syscall_table.c:15:6: warning: symbol 'sys_call_table' was not declared. Should it be static? arch/riscv/kernel/traps.c:149:13: warning: symbol 'trap_init' was not declared. Should it be static? arch/riscv/kernel/vdso.c:54:5: warning: symbol 'arch_setup_additional_pages' was not declared. Should it be static? arch/riscv/kernel/smp.c:64:6: warning: symbol 'arch_match_cpu_phys_id' was not declared. Should it be static? arch/riscv/kernel/module-sections.c:89:5: warning: symbol 'module_frob_arch_sections' was not declared. Should it be static? arch/riscv/mm/context.c:42:6: warning: symbol 'switch_mm' was not declared. Should it be static? Fix by including the appropriate header files in the appropriate source files. This patch should have no functional impact. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
2019-10-28riscv: mark some code and data as file-staticPaul Walmsley1-1/+1
Several functions and arrays which are only used in the files in which they are declared are missing "static" qualifiers. Warnings for these symbols are reported by sparse: arch/riscv/kernel/vdso.c:28:18: warning: symbol 'vdso_data' was not declared. Should it be static? arch/riscv/mm/sifive_l2_cache.c:145:12: warning: symbol 'sifive_l2_init' was not declared. Should it be static? Resolve these warnings by marking them as static. This version incorporates feedback from Greentime Hu <greentime.hu@sifive.com>. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Greentime Hu <greentime.hu@sifive.com>
2019-10-28riscv: add prototypes for assembly language functions from head.SPaul Walmsley3-0/+25
Add prototypes for assembly language functions defined in head.S, and include these prototypes into C source files that call those functions. This patch resolves the following warnings from sparse: arch/riscv/kernel/setup.c:39:10: warning: symbol 'hart_lottery' was not declared. Should it be static? arch/riscv/kernel/setup.c:42:13: warning: symbol 'parse_dtb' was not declared. Should it be static? arch/riscv/kernel/smpboot.c:33:6: warning: symbol '__cpu_up_stack_pointer' was not declared. Should it be static? arch/riscv/kernel/smpboot.c:34:6: warning: symbol '__cpu_up_task_pointer' was not declared. Should it be static? arch/riscv/mm/fault.c:25:17: warning: symbol 'do_page_fault' was not declared. Should it be static? This change should have no functional impact. Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-25riscv: cleanup do_trap_breakChristoph Hellwig1-20/+6
If we always compile the get_break_insn_length inline function we can remove the ifdefs and let dead code elimination take care of the warn branch that is now unreadable because the report_bug stub always returns BUG_TRAP_TYPE_BUG. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Anup Patel <anup@brainfault.org> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-18riscv: Use pr_warn instead of pr_warningKefeng Wang1-2/+2
As said in commit f2c2cbcc35d4 ("powerpc: Use pr_warn instead of pr_warning"), removing pr_warning so all logging messages use a consistent <prefix>_warn style. Let's do it. Link: http://lkml.kernel.org/r/20191018031850.48498-4-wangkefeng.wang@huawei.com To: linux-kernel@vger.kernel.org Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Palmer Dabbelt <palmer@sifive.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com>
2019-10-14riscv: remove the switch statement in do_trap_break()Vincent Chen1-11/+11
To make the code more straightforward, replace the switch statement with an if statement. Suggested-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Vincent Chen <vincent.chen@sifive.com> [paul.walmsley@sifive.com: cleaned up patch description; updated to apply] Link: https://lore.kernel.org/linux-riscv/20190927224711.GI4700@infradead.org/ Link: https://lore.kernel.org/linux-riscv/CABvJ_xiHJSB7P5QekuLRP=LBPzXXghAfuUpPUYb=a_HbnOQ6BA@mail.gmail.com/ Link: https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/VDCU2WOB6KQISREO4V5DTXEI2M7VOV55/ Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-09RISC-V: entry: Remove unneeded need_resched() loopValentin Schneider1-2/+1
Since the enabling and disabling of IRQs within preempt_schedule_irq() is contained in a need_resched() loop, we don't need the outer arch code loop. Reviewed-by: Palmer Dabbelt <palmer@sifive.com> Signed-off-by: Valentin Schneider <valentin.schneider@arm.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: linux-riscv@lists.infradead.org Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-07riscv: Correct the handling of unexpected ebreak in do_trap_break()Vincent Chen1-3/+3
For the kernel space, all ebreak instructions are determined at compile time because the kernel space debugging module is currently unsupported. Hence, it should be treated as a bug if an ebreak instruction which does not belong to BUG_TRAP_TYPE_WARN or BUG_TRAP_TYPE_BUG is executed in kernel space. For the userspace, debugging module or user problem may intentionally insert an ebreak instruction to trigger a SIGTRAP signal. To approach the above two situations, the do_trap_break() will direct the BUG_TRAP_TYPE_NONE ebreak exception issued in kernel space to die() and will send a SIGTRAP to the trapped process only when the ebreak is in userspace. Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> [paul.walmsley@sifive.com: fixed checkpatch issue] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-07riscv: avoid sending a SIGTRAP to a user thread trapped in WARN()Vincent Chen1-1/+1
On RISC-V, when the kernel runs code on behalf of a user thread, and the kernel executes a WARN() or WARN_ON(), the user thread will be sent a bogus SIGTRAP. Fix the RISC-V kernel code to not send a SIGTRAP when a WARN()/WARN_ON() is executed. Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> [paul.walmsley@sifive.com: fixed subject] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-07riscv: avoid kernel hangs when trapped in BUG()Vincent Chen1-3/+3
When the CONFIG_GENERIC_BUG is disabled by disabling CONFIG_BUG, if a kernel thread is trapped by BUG(), the whole system will be in the loop that infinitely handles the ebreak exception instead of entering the die function. To fix this problem, the do_trap_break() will always call the die() to deal with the break exception as the type of break is BUG_TRAP_TYPE_BUG. Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-10-01RISC-V: Clear load reservations while restoring hart contextsPalmer Dabbelt1-1/+20
This is almost entirely a comment. The bug is unlikely to manifest on existing hardware because there is a timeout on load reservations, but manifests on QEMU because there is no timeout. Signed-off-by: Palmer Dabbelt <palmer@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-20riscv: Avoid interrupts being erroneously enabled in handle_exception()Vincent Chen1-1/+5
When the handle_exception function addresses an exception, the interrupts will be unconditionally enabled after finishing the context save. However, It may erroneously enable the interrupts if the interrupts are disabled before entering the handle_exception. For example, one of the WARN_ON() condition is satisfied in the scheduling where the interrupt is disabled and rq.lock is locked. The WARN_ON will trigger a break exception and the handle_exception function will enable the interrupts before entering do_trap_break function. During the procedure, if a timer interrupt is pending, it will be taken when interrupts are enabled. In this case, it may cause a deadlock problem if the rq.lock is locked again in the timer ISR. Hence, the handle_exception() can only enable interrupts when the state of sstatus.SPIE is 1. This patch is tested on HiFive Unleashed board. Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Palmer Dabbelt <palmer@sifive.com> [paul.walmsley@sifive.com: updated to apply] Fixes: bcae803a21317 ("RISC-V: Enable IRQ during exception handling") Cc: David Abdurachmanov <david.abdurachmanov@sifive.com> Cc: stable@vger.kernel.org Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
2019-09-20RISC-V: Export kernel symbols for kvmAtish Patra2-0/+2
Export a few symbols used by kvm module. Without this, kvm cannot be compiled as a module. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Alexander Graf <graf@amazon.com> [paul.walmsley@sifive.com: updated to apply; clarified short patch description] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 18:32:50 +0000