| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Resource management:
- Add support for Enhanced Allocation devices (Sean O. Stalley)
- Add Enhanced Allocation register entries (Sean O. Stalley)
- Handle IORESOURCE_PCI_FIXED when sizing resources (David Daney)
- Handle IORESOURCE_PCI_FIXED when assigning resources (David Daney)
- Handle Enhanced Allocation capability for SR-IOV devices (David Daney)
- Clear IORESOURCE_UNSET when reverting to firmware-assigned address (Bjorn Helgaas)
- Make Enhanced Allocation bitmasks more obvious (Bjorn Helgaas)
- Expand Enhanced Allocation BAR output (Bjorn Helgaas)
- Add of_pci_check_probe_only to parse "linux,pci-probe-only" (Marc Zyngier)
- Fix lookup of linux,pci-probe-only property (Marc Zyngier)
- Add sparc mem64 resource parsing for root bus (Yinghai Lu)
PCI device hotplug:
- pciehp: Queue power work requests in dedicated function (Guenter Roeck)
Driver binding:
- Add builtin_pci_driver() to avoid registration boilerplate (Paul Gortmaker)
Virtualization:
- Set SR-IOV NumVFs to zero after enumeration (Alexander Duyck)
- Remove redundant validation of SR-IOV offset/stride registers (Alexander Duyck)
- Remove VFs in reverse order if virtfn_add() fails (Alexander Duyck)
- Reorder pcibios_sriov_disable() (Alexander Duyck)
- Wait 1 second between disabling VFs and clearing NumVFs (Alexander Duyck)
- Fix sriov_enable() error path for pcibios_enable_sriov() failures (Alexander Duyck)
- Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs (Ben Shelton)
- Don't try to restore VF BARs (Wei Yang)
MSI:
- Don't alloc pcibios-irq when MSI is enabled (Joerg Roedel)
- Add msi_controller setup_irqs() method for special multivector setup (Lucas Stach)
- Export all remapped MSIs to sysfs attributes (Romain Bezut)
- Disable MSI on SiS 761 (Ondrej Zary)
AER:
- Clear error status registers during enumeration and restore (Taku Izumi)
Generic host bridge driver:
- Fix lookup of linux,pci-probe-only property (Marc Zyngier)
- Allow multiple hosts with different map_bus() methods (David Daney)
- Pass starting bus number to pci_scan_root_bus() (David Daney)
- Fix address window calculation for non-zero starting bus (David Daney)
Altera host bridge driver:
- Add msi.h to ARM Kbuild (Ley Foon Tan)
- Add Altera PCIe host controller driver (Ley Foon Tan)
- Add Altera PCIe MSI driver (Ley Foon Tan)
APM X-Gene host bridge driver:
- Remove msi_controller assignment (Duc Dang)
Broadcom iProc host bridge driver:
- Fix header comment "Corporation" misspelling (Florian Fainelli)
- Fix code comment to match code (Ray Jui)
- Remove unused struct iproc_pcie.irqs[] (Ray Jui)
- Call pci_fixup_irqs() for ARM64 as well as ARM (Ray Jui)
- Fix PCIe reset logic (Ray Jui)
- Improve link detection logic (Ray Jui)
- Update PCIe device tree bindings (Ray Jui)
- Add outbound mapping support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Return real error code from imx6_add_pcie_port() (Fabio Estevam)
- Add PCIE_PHY_RX_ASIC_OUT_VALID definition (Fabio Estevam)
Freescale Layerscape host bridge driver:
- Remove ls_pcie_establish_link() (Minghuan Lian)
- Ignore PCIe controllers in Endpoint mode (Minghuan Lian)
- Factor out SCFG related function (Minghuan Lian)
- Update ls_add_pcie_port() (Minghuan Lian)
- Remove unused fields from struct ls_pcie (Minghuan Lian)
- Add support for LS1043a and LS2080a (Minghuan Lian)
- Add ls_pcie_msi_host_init() (Minghuan Lian)
HiSilicon host bridge driver:
- Add HiSilicon SoC Hip05 PCIe driver (Zhou Wang)
Marvell MVEBU host bridge driver:
- Return zero for reserved or unimplemented config space (Russell King)
- Use exact config access size; don't read/modify/write (Russell King)
- Use of_get_available_child_count() (Russell King)
- Use for_each_available_child_of_node() to walk child nodes (Russell King)
- Report full node name when reporting a DT error (Russell King)
- Use port->name rather than "PCIe%d.%d" (Russell King)
- Move port parsing and resource claiming to separate function (Russell King)
- Fix memory leaks and refcount leaks (Russell King)
- Split port parsing and resource claiming from port setup (Russell King)
- Use gpio_set_value_cansleep() (Russell King)
- Use devm_kcalloc() to allocate an array (Russell King)
- Use gpio_desc to carry around gpio (Russell King)
- Improve clock/reset handling (Russell King)
- Add PCI Express root complex capability block (Russell King)
- Remove code restricting accesses to slot 0 (Russell King)
NVIDIA Tegra host bridge driver:
- Wrap static pgprot_t initializer with __pgprot() (Ard Biesheuvel)
Renesas R-Car host bridge driver:
- Build pci-rcar-gen2.c only on ARM (Geert Uytterhoeven)
- Build pcie-rcar.c only on ARM (Geert Uytterhoeven)
- Make PCI aware of the I/O resources (Phil Edworthy)
- Remove dependency on ARM-specific struct hw_pci (Phil Edworthy)
- Set root bus nr to that provided in DT (Phil Edworthy)
- Fix I/O offset for multiple host bridges (Phil Edworthy)
ST Microelectronics SPEAr13xx host bridge driver:
- Fix dw_pcie_cfg_read/write() usage (Gabriele Paoloni)
Synopsys DesignWare host bridge driver:
- Make "clocks" and "clock-names" optional DT properties (Bhupesh Sharma)
- Use exact access size in dw_pcie_cfg_read() (Gabriele Paoloni)
- Simplify dw_pcie_cfg_read/write() interfaces (Gabriele Paoloni)
- Require config accesses to be naturally aligned (Gabriele Paoloni)
- Make "num-lanes" an optional DT property (Gabriele Paoloni)
- Move calculation of bus addresses to DRA7xx (Gabriele Paoloni)
- Replace ARM pci_sys_data->align_resource with global function pointer (Gabriele Paoloni)
- Factor out MSI msg setup (Lucas Stach)
- Implement multivector MSI IRQ setup (Lucas Stach)
- Make get_msi_addr() return phys_addr_t, not u32 (Lucas Stach)
- Set up high part of MSI target address (Lucas Stach)
- Fix PORT_LOGIC_LINK_WIDTH_MASK (Zhou Wang)
- Revert "PCI: designware: Program ATU with untranslated address" (Zhou Wang)
- Use of_pci_get_host_bridge_resources() to parse DT (Zhou Wang)
- Make driver arch-agnostic (Zhou Wang)
Miscellaneous:
- Make x86 pci_subsys_init() static (Alexander Kuleshov)
- Turn off Request Attributes to avoid Chelsio T5 Completion erratum (Hariprasad Shenai)"
* tag 'pci-v4.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
PCI: altera: Add Altera PCIe MSI driver
PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver
PCI: layerscape: Add ls_pcie_msi_host_init()
PCI: layerscape: Add support for LS1043a and LS2080a
PCI: layerscape: Remove unused fields from struct ls_pcie
PCI: layerscape: Update ls_add_pcie_port()
PCI: layerscape: Factor out SCFG related function
PCI: layerscape: Ignore PCIe controllers in Endpoint mode
PCI: layerscape: Remove ls_pcie_establish_link()
PCI: designware: Make "clocks" and "clock-names" optional DT properties
PCI: designware: Make driver arch-agnostic
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
Revert "PCI: designware: Program ATU with untranslated address"
PCI: designware: Move calculation of bus addresses to DRA7xx
PCI: designware: Make "num-lanes" an optional DT property
PCI: designware: Require config accesses to be naturally aligned
PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
PCI: designware: Use exact access size in dw_pcie_cfg_read()
PCI: spear: Fix dw_pcie_cfg_read/write() usage
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
|
|
MPC5xxx updates from Anatolij:
"Highlights include a driver for MPC512x LocalPlus Bus FIFO with its
device tree binding documentation, mpc512x device tree updates and some
minor fixes."
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into next
Freescale updates from Scott:
"Highlights include 64-bit book3e kexec/kdump support, a rework of the
qoriq clock driver, device tree changes including qoriq fman nodes,
support for a new 85xx board, and some fixes.
Note that there is a trivial merge conflict with the clock tree's next
branch, in the clock Makefile."
|
|
Commit a030e1e4bbd085bbcfd0a23f8d355fcd41f39bed make a change to use
kstrndup() instead of kmalloc() + strlcpy() in the pseries_of_derive_parent()
routine that introduces a subtle change in the parent path name generated.
The kstrndup() routine will copy n characters followed by a terminating null,
whereas strlcpy() will copy n-1 characters and add a terminating null.
This slight difference results in having a parent path that includes the
tailing '/' character, "/cpus/" vs. "/cpus". This then causes the subsequent
call to of_find_node_by_path() to fail, and in the case of DLPAR add
operations the DLPAR request fails.
This patch decrements the pointer returned from kbasename() to point to the
'/' character before the base name instead of the base name. This then
adjusts the string length calculations to not include the trailing '/'
in the parent path name.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is a major overhaul of the clk-qoriq driver, which I'm merging
via PPC with Stephen Boyd's ack in order to apply subsequent PPC patches
that depend on it.
|
|
The new kernel will be expecting secondary threads to be disabled,
not spinning.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Unlike 32-bit 85xx kexec, we don't do a core reset.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood: edit changelog, and cleanup]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfree in probe function.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
This driver for Freescale MPC512x LocalPlus Bus FIFO (called SCLPC
in the Reference Manual) allows Direct Memory Access transfers
between RAM and peripheral devices on LocalPlus Bus.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Freescale's Layerscape ARM chips use the same structure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This fixes a bug where it is possible for an off-line CPU to fail to go
into a low-power state (nap/sleep/winkle), and to become unresponsive to
requests from the KVM subsystem to wake up and run a VCPU. What can
happen is that a maskable interrupt of some kind (external, decrementer,
hypervisor doorbell, or HMI) after we have called local_irq_disable() at
the beginning of pnv_smp_cpu_kill_self() and before interrupts are
hard-disabled inside power7_nap/sleep/winkle(). In this situation, the
pending event is marked in the irq_happened flag in the PACA. This
pending event prevents power7_nap/sleep/winkle from going to the
requested low-power state; instead they return immediately. We don't
deal with any of these pending event flags in the off-line loop in
pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case,
so we will have srr1 == 0, and none of the processing to clear
interrupts or doorbells will be done.
Usually, the most obvious symptom of this is that a KVM guest will fail
with a console message saying "KVM: couldn't grab cpu N".
This fixes the problem by making sure we handle the irq_happened flags
properly. First, we hard-disable before the off-line loop. Once we have
hard-disabled, the irq_happened flags can't change underneath us. We
unconditionally clear the DEC and HMI flags: there is no processing of
timer interrupts while off-line, and the necessary HMI processing is all
done in lower-level code. We leave the EE and DBELL flags alone for the
first iteration of the loop, so that we won't fail to respond to a
split-core request that came in just before hard-disabling. Within the
loop, we handle external interrupts if the EE bit is set in irq_happened
as well as if the low-power state was interrupted by an external
interrupt. (We don't need to do the msgclr for a pending doorbell in
irq_happened, because doorbells are edge-triggered and don't remain
pending in hardware.) Then we clear both the EE and DBELL flags, and
once clear, they cannot be set again (until this CPU comes online again,
that is).
This also fixes the debug check to not be done when we just ran a KVM
guest or when the sleep didn't happen because of a pending event in
irq_happened.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Similar to commit b6541db ("powerpc/eeh: Block PCI config access
upon frozen PE"), this blocks the PCI config space of Broadcom
Shiner adapter until PE reset is completed, to avoid recursive
fenced PHB when dumping PCI config registers during the period
of error recovery.
~# lspci -ns 0003:03:00.0
0003:03:00.0 0200: 14e4:168a (rev 10)
~# lspci -s 0003:03:00.0
0003:03:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57800 1/10 Gigabit Ethernet (rev 10)
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This simplifies pnv_eeh_set_option() to avoid unnecessary nested
if statements, to improve readability. No functional changes.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This moves the logic of pnv_eeh_cap_start() to pnv_eeh_find_cap()
as the function is only called by pnv_eeh_find_cap(). The logic
of both functions are pretty simple. No need to have separate
functions.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This applies cleanup on eeh-powernv.c, no functional changes:
* Remove unnecessary comments and empty line.
* Correct inaccurate comments.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This cleans up pseries_eeh_get_state(), no functional changes:
* Return EEH_STATE_NOT_SUPPORT early when the 2nd RTAS output
argument is zero to avoid nested if statements.
* Skip clearing bits in the PE state represented by variable
"result" to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The TUNE_CELL option allows you to build a kernel that runs on multiple
CPUs but is tuned (ie. optimised) to run on Cell CPUs. Now days no one
is building a distro in that fashion, and any users who are building
custom kernels for their Cell machines are better off building with
CONFIG_CELL_CPU, which builds a kernel that only runs on Cell and
therefore can be optimised even more aggresively.
Dropping the option also avoids confusing other users, who are presented
with an option to tune for Cell when they are not building for a Cell
CPU at all.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
85xx currently uses the generic timebase sync mechanism when
CONFIG_KEXEC is enabled, because 32-bit 85xx kexec support does a hard
reset of each core. 64-bit 85xx kexec does not do this, so we neither
need nor want this (nor is the generic timebase sync code built on
ppc64).
FWIW, I don't like the fact that the hard reset is done on 32-bit
kexec, and I especially don't like the timebase sync being triggered
only on the presence of CONFIG_KEXEC rather than actually booting in
that environment, but that's beyond the scope of this patch...
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Problems have been observed in coreint (EPR) mode if interrupts are
left pending (due to the lack of device quiescence with kdump) after
having tried to deliver to a CPU but unable to deliver due to MSR[EE]
-- interrupts no longer get reliably delivered in the new kernel. I
tried various ways of fixing it up inside the crash kernel itself, and
none worked (including resetting the entire mpic). Masking all
interrupts and issuing EOIs in the crashing kernel did help a lot of
the time, but the behavior was not consistent.
Thus, stick to standard IACK mode when kdump is a possibility.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This allows SMP kernels to work as kdump crash kernels. While crash
kernels don't really need to be SMP, this prevents things from breaking
if a user does it anyway (which is not something you want to only find
out once the main kernel has crashed in the field, especially if
whether it works or not depends on which cpu crashed).
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This board uses a P5020 chip, and boots just fine using
the corenet_generic code. The device tree is very similar to the
P5020DS, except that there is no Flash memory. The environment is,
instead, stored on an MMC card on the motherboard.
Signed-off-by: Andy Fleming <afleming@gmail.com>
[scottwood: fixed trailing whitespace]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Core reset may cause issue if using the proxy mode of MPIC.
Use the mixed mode of MPIC if enabling CPU hotplug.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Now that pseries selects PCI_MSI && PCI, EEH will always be true, and
therefore CONFIG_PSERIES_MSI will always be true. So drop it, and move
msi.o to obj-y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Make it entirely clear in the Makefile that we always build the pci
related files by moving them to obj-y.
Note that CONFIG_EEH is now always enabled on pseries, because it
depends on PSERIES && PCI.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that we always have CONFIG_PCI=y for pseries, we can stop guarding
code with CONFIG_PCI ifdefs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pseries build with PCI=n looks to have been broken for at least 5
years, and no one's noticed or cared.
Following the obvious breakages backward, the first commit I can find
that builds is the parent of 2eb4afb69ff3 ("powerpc/pci: Move pseries
code into pseries platform specific area") from April 2009.
A distro would never ship a PCI=n kernel, so it is only useful for folks
building custom kernels. Also on KVM the virtio devices appear on PCI,
so it would only be useful if you were building kernels specifically to
run on PowerVM and with no PCI devices.
The added code complexity, and testing load (which we've clearly not
been doing), is not justified by the small reduction in kernel size for
such a niche use case.
So just make PCI non-optional on pseries.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
All unrecovered machine check errors on PowerNV should cause an
immediate panic. There are 2 reasons that this is the right policy:
it's not safe to continue, and we're already trying to reboot.
Firstly, if we go through the recovery process and do not successfully
recover, we can't be sure about the state of the machine, and it is
not safe to recover and proceed.
Linux knows about the following sources of Machine Check Errors:
- Uncorrectable Errors (UE)
- Effective - Real Address Translation (ERAT)
- Segment Lookaside Buffer (SLB)
- Translation Lookaside Buffer (TLB)
- Unknown/Unrecognised
In the SLB, TLB and ERAT cases, we can further categorise these as
parity errors, multihit errors or unknown/unrecognised.
We can handle SLB errors by flushing and reloading the SLB. We can
handle TLB and ERAT multihit errors by flushing the TLB. (It appears
we may not handle TLB and ERAT parity errors: I will investigate
further and send a followup patch if appropriate.)
This leaves us with uncorrectable errors. Uncorrectable errors are
usually the result of ECC memory detecting an error that it cannot
correct, but they also crop up in the context of PCI cards failing
during DMA writes, and during CAPI error events.
There are several types of UE, and there are 3 places a UE can occur:
Skiboot, the kernel, and userspace. For Skiboot errors, we have the
facility to make some recoverable. For userspace, we can simply kill
(SIGBUS) the affected process. We have no meaningful way to deal with
UEs in kernel space or in unrecoverable sections of Skiboot.
Currently, these unrecovered UEs fall through to
machine_check_expection() in traps.c, which calls die(), which OOPSes
and sends SIGBUS to the process. This sometimes allows us to stumble
onwards. For example we've seen UEs kill the kernel eehd and
khugepaged. However, the process killed could have held a lock, or it
could have been a more important process, etc: we can no longer make
any assertions about the state of the machine. Similarly if we see a
UE in skiboot (and again we've seen this happen), we're not in a
position where we can make any assertions about the state of the
machine.
Likewise, for unknown or unrecognised errors, we're not able to say
anything about the state of the machine.
Therefore, if we have an unrecovered MCE, the most appropriate thing
to do is to panic.
The second reason is that since e784b6499d9c ("powerpc/powernv: Invoke
opal_cec_reboot2() on unrecoverable machine check errors."), we
attempt a special OPAL reboot on an unhandled MCE. This is so the
hardware can record error data for later debugging.
The comments in that commit assert that we are heading down the panic
path anyway. At the moment this is not always true. With UEs in kernel
space, for instance, they are marked as recoverable by the hardware,
so if the attempt to reboot failed (e.g. old Skiboot), we wouldn't
panic() but would simply die() and OOPS. It doesn't make sense to be
staggering on if we've just tried to reboot: we should panic().
Explicitly panic() on unrecovered MCEs on PowerNV.
Update the comments appropriately.
This fixes some hangs following EEH events on cxlflash setups.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pi_buff is being memset before it is sanity checked. Move the
memset after the null pi_buff sanity check to avoid an oops.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Always include a timeout when waiting for secondary cpus to enter OPAL
in the kexec path, rather than only when crashing.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The derive_parent() has similar semantics to what we have in newly introduced
of_helpers module. The replacement reduces code base and propagates the actual
error code to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In case we have node without '/' strrchr() returns NULL which might lead to
crash. Replace strrchr() by kbasename() and modify condition to avoid such
behaviour.
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The helper kstrndup() will do the same in one line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In case we have a full node name like /foo/bar and /foo is not found the
parent_path left unfreed. So, free a memory before return to a caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Extract a new module to share the code between other modules.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This struct is unused, which is now a build error with gcc 6:
error: 'os_area_db_id_video_mode' defined but not used
There doesn't seem to be any good reason to keep it around so remove it,
it's in the history if anyone needs it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently, little endian is only supported on powernv and pseries,
however, Kconfigs still allow us to include other platforms in a LE
kernel, this may result in space wasting or even build error if some
BE-only platforms always assume they are built for a BE kernel. So just
modify the Kconfigs of BE-only platforms to remove them from being built
for a LE kernel.
For 32bit only platforms, nothing needs to be done, because
CPU_LITTLE_ENDIAN depends on PPC64. For 64bit supported platforms, add
CPU_BIG_ENDIAN to dependencies explicitly, so that these platforms will
be disabled for LE [Suggested-by: Cédric Le Goater <clg@fr.ibm.com>].
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
|
|
When find_and_init_phbs() looks for the probe-only property, it seems to
trust the firmware to be correctly written, and assumes that there is a
parameter to the property.
It is conceivable that the firmware could not be that perfect, and it could
expose this property naked (at least one arm64 platform seems to exhibit
this exact behaviour). The setup code the ends up making a decision based
on whatever the property pointer points to, which is likely to be junk.
Instead, switch to the common of_pci.c implementation that doesn't suffer
from this problem and ignore the property if the firmware couldn't make up
its mind.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
@@
struct irq_data *d;
expression E1;
@@
-__irq_set_handler_locked(d->irq, E1);
+irq_set_handler_locked(d, E1);
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
|
|
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
|
|
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: linuxppc-dev@lists.ozlabs.org
|
|
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
|
|
This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
Fixes: 05af7bd2d75e ("[POWERPC] MPIC U3/U4 MSI backend")
Cc: stable@vger.kernel.org # v2.6.22+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
alloc_pages_exact_node() was introduced in commit 6484eb3e2a81 ("page
allocator: do not check NUMA node ID when the caller knows the node is
valid") as an optimized variant of alloc_pages_node(), that doesn't
fallback to current node for nid == NUMA_NO_NODE. Unfortunately the
name of the function can easily suggest that the allocation is
restricted to the given node and fails otherwise. In truth, the node is
only preferred, unless __GFP_THISNODE is passed among the gfp flags.
The misleading name has lead to mistakes in the past, see for example
commits 5265047ac301 ("mm, thp: really limit transparent hugepage
allocation to local node") and b360edb43f8e ("mm, mempolicy:
migrate_to_node should only migrate to node").
Another issue with the name is that there's a family of
alloc_pages_exact*() functions where 'exact' means exact size (instead
of page order), which leads to more confusion.
To prevent further mistakes, this patch effectively renames
alloc_pages_exact_node() to __alloc_pages_node() to better convey that
it's an optimized variant of alloc_pages_node() not intended for general
usage. Both functions get described in comments.
It has been also considered to really provide a convenience function for
allocations restricted to a node, but the major opinion seems to be that
__GFP_THISNODE already provides that functionality and we shouldn't
duplicate the API needlessly. The number of users would be small
anyway.
Existing callers of alloc_pages_exact_node() are simply converted to
call __alloc_pages_node(), with the exception of sba_alloc_coherent()
which open-codes the check for NUMA_NO_NODE, so it is converted to use
alloc_pages_node() instead. This means it no longer performs some
VM_BUG_ON checks, and since the current check for nid in
alloc_pages_node() uses a 'nid < 0' comparison (which includes
NUMA_NO_NODE), it may hide wrong values which would be previously
exposed.
Both differences will be rectified by the next patch.
To sum up, this patch makes no functional changes, except temporarily
hiding potentially buggy callers. Restricting the checks in
alloc_pages_node() is left for the next patch which can in turn expose
more existing buggy callers.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Robin Holt <robinmholt@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cliff Whickman <cpw@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
