| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- One fix for the interrupt rework we did last release which broke
KVM-PR
- Three commits fixing some fallout from the READ_ONCE() changes
interacting badly with our 8xx 16K pages support, which uses a pte_t
that is a structure of 4 actual PTEs
- A cleanup of the 8xx pte_update() to use the newly added pmd_off()
- A fix for a crash when handling an oops if CONFIG_DEBUG_VIRTUAL is
enabled
- A minor fix for the SPU syscall generation
Thanks to Aneesh Kumar K.V, Christian Zigotzky, Christophe Leroy, Mike
Rapoport, Nicholas Piggin.
* tag 'powerpc-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/8xx: Provide ptep_get() with 16k pages
mm: Allow arches to provide ptep_get()
mm/gup: Use huge_ptep_get() in gup_hugepte()
powerpc/syscalls: Use the number when building SPU syscall table
powerpc/8xx: use pmd_off() to access a PMD entry in pte_update()
powerpc/64s: Fix KVM interrupt using wrong save area
powerpc: Fix kernel crash in show_instructions() w/DEBUG_VIRTUAL
|
|
Now that we've renamed probe_kernel_address() to get_kernel_nofault()
and made it look and behave more in line with get_user(), some of the
subtle type behavior differences end up being more obvious and possibly
dangerous.
When you do
get_user(val, user_ptr);
the type of the access comes from the "user_ptr" part, and the above
basically acts as
val = *user_ptr;
by design (except, of course, for the fact that the actual dereference
is done with a user access).
Note how in the above case, the type of the end result comes from the
pointer argument, and then the value is cast to the type of 'val' as
part of the assignment.
So the type of the pointer is ultimately the more important type both
for the access itself.
But 'get_kernel_nofault()' may now _look_ similar, but it behaves very
differently. When you do
get_kernel_nofault(val, kernel_ptr);
it behaves like
val = *(typeof(val) *)kernel_ptr;
except, of course, for the fact that the actual dereference is done with
exception handling so that a faulting access is suppressed and returned
as the error code.
But note how different the casting behavior of the two superficially
similar accesses are: one does the actual access in the size of the type
the pointer points to, while the other does the access in the size of
the target, and ignores the pointer type entirely.
Actually changing get_kernel_nofault() to act like get_user() is almost
certainly the right thing to do eventually, but in the meantime this
patch adds logit to at least verify that the pointer type is compatible
with the type of the result.
In many cases, this involves just casting the pointer to 'void *' to
make it obvious that the type of the pointer is not the important part.
It's not how 'get_user()' acts, but at least the behavioral difference
is now obvious and explicit.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Better describe what this helper does, and match the naming of
copy_from_kernel_nofault.
Also switch the argument order around, so that it acts and looks
like get_user().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Better describe what these functions do.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Better describe what these functions do.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The CTR register reload in the KVM interrupt path used the wrong save
area for SLB (and NMI) interrupts.
Fixes: 9600f261acaa ("powerpc/64s/exception: Move KVM test to common code")
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200615061247.1310763-1-npiggin@gmail.com
|
|
With CONFIG_DEBUG_VIRTUAL=y, we can hit a BUG() if we take a hard
lockup watchdog interrupt when in OPAL mode.
This happens in show_instructions() if the kernel takes the watchdog
NMI IPI, or any other interrupt, with MSR_IR == 0. show_instructions()
updates the variable pc in the loop and the second iteration will
result in BUG().
We hit the BUG_ON due the below check in __va()
#define __va(x)
({
VIRTUAL_BUG_ON((unsigned long)(x) >= PAGE_OFFSET);
(void *)(unsigned long)((phys_addr_t)(x) | PAGE_OFFSET);
})
Fix it by moving the check out of the loop. Also update nip so that
the nip == pc check still matches.
Fixes: 4dd7554a6456 ("powerpc/64: Add VIRTUAL_BUG_ON checks for __va and __pa addresses")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Use IS_ENABLED(), massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200524093822.423487-1-aneesh.kumar@linux.ibm.com
|
|
This change converts the existing mmap_sem rwsem calls to use the new mmap
locking API instead.
The change is generated using coccinelle with the following rule:
// spatch --sp-file mmap_lock_api.cocci --in-place --include-headers --dir .
@@
expression mm;
@@
(
-init_rwsem
+mmap_init_lock
|
-down_write
+mmap_write_lock
|
-down_write_killable
+mmap_write_lock_killable
|
-down_write_trylock
+mmap_write_trylock
|
-up_write
+mmap_write_unlock
|
-downgrade_write
+mmap_write_downgrade
|
-down_read
+mmap_read_lock
|
-down_read_killable
+mmap_read_lock_killable
|
-down_read_trylock
+mmap_read_trylock
|
-up_read
+mmap_read_unlock
)
-(&mm->mmap_sem)
+(mm)
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Liam Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ying Han <yinghan@google.com>
Link: http://lkml.kernel.org/r/20200520052908.204642-5-walken@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now the last users of show_stack() got converted to use an explicit log
level, show_stack_loglvl() can drop it's redundant suffix and become once
again well known show_stack().
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20200418201944.482088-51-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the log-level of show_stack() depends on a platform
realization. It creates situations where the headers are printed with
lower log level or higher than the stacktrace (depending on a platform or
user).
Furthermore, it forces the logic decision from user to an architecture
side. In result, some users as sysrq/kdb/etc are doing tricks with
temporary rising console_loglevel while printing their messages. And in
result it not only may print unwanted messages from other CPUs, but also
omit printing at all in the unlucky case where the printk() was deferred.
Introducing log-level parameter and KERN_UNSUPPRESSED [1] seems an easier
approach than introducing more printk buffers. Also, it will consolidate
printings with headers.
Introduce show_stack_loglvl(), that eventually will substitute
show_stack().
[1]: https://lore.kernel.org/lkml/20190528002412.1625-1-dima@arista.com/T/#u
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Link: http://lkml.kernel.org/r/20200418201944.482088-27-dima@arista.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
|
|
Merge updates from Andrew Morton:
"A few little subsystems and a start of a lot of MM patches.
Subsystems affected by this patch series: squashfs, ocfs2, parisc,
vfs. With mm subsystems: slab-generic, slub, debug, pagecache, gup,
swap, memcg, pagemap, memory-failure, vmalloc, kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
kasan: move kasan_report() into report.c
mm/mm_init.c: report kasan-tag information stored in page->flags
ubsan: entirely disable alignment checks under UBSAN_TRAP
kasan: fix clang compilation warning due to stack protector
x86/mm: remove vmalloc faulting
mm: remove vmalloc_sync_(un)mappings()
x86/mm/32: implement arch_sync_kernel_mappings()
x86/mm/64: implement arch_sync_kernel_mappings()
mm/ioremap: track which page-table levels were modified
mm/vmalloc: track which page-table levels were modified
mm: add functions to track page directory modifications
s390: use __vmalloc_node in stack_alloc
powerpc: use __vmalloc_node in alloc_vm_stack
arm64: use __vmalloc_node in arch_alloc_vmap_stack
mm: remove vmalloc_user_node_flags
mm: switch the test_vmalloc module to use __vmalloc_node
mm: remove __vmalloc_node_flags_caller
mm: remove both instances of __vmalloc_node_flags
mm: remove the prot argument to __vmalloc_node
mm: remove the pgprot argument to __vmalloc
...
|
|
alloc_vm_stack can use a slightly higher level vmalloc function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-29-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the two remaining callers to use __get_vm_area_caller instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-9-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These helpers are only used for remapping the ISA I/O base. Replace the
mapping side with a remap_isa_range helper in isa-bridge.c that hard codes
all the known arguments, and just remove __iounmap_at in favour of open
coding it in the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-8-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Factor code shared between pci_64 and electra_cf into a ioremap_pbh helper
that follows the normal ioremap semantics, and returns a useful __iomem
pointer. Note that it opencodes __ioremap_at as we know from the callers
the slab is available. Switch pci_64 to also store the result as __iomem
pointer, and unmap the result using iounmap instead of force casting and
using vmalloc APIs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-7-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PVR value of 0x0F000006 means we are arch v3.1 compliant (i.e.
POWER10). This is used by phyp and kvm when booting as a pseries guest
to detect the presence of new P10 features and to enable the
appropriate hwcap and facility bits.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[mpe: Fall through to __init_FSCR rather than duplicating it, drop
hack to set current->thread.fscr now that is handled elsewhere.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200521014341.29095-8-alistair@popple.id.au
|
|
Matrix multiple assist (MMA) is a new feature added to ISAv3.1 and
POWER10. Support on powernv can be selected via a firmware CPU device
tree feature which enables it via a PCR bit.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200521014341.29095-7-alistair@popple.id.au
|
|
Prefix instructions have their own FSCR bit which needs to be enabled
via a CPU feature. The kernel will save the FSCR for problem state but
it needs to be enabled initially.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200521014341.29095-6-alistair@popple.id.au
|
|
On powernv hardware support for ISAv3.1 is advertised via a cpu feature
bit in the device tree. This patch enables the associated HWCAP bit if
the device tree indicates ISAv3.1 is available.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200521014341.29095-4-alistair@popple.id.au
|
|
At boot the FSCR is initialised via one of two paths. On most systems
it's set to a hard coded value in __init_FSCR().
On newer skiboot systems we use the device tree CPU features binding,
where firmware can tell Linux what bits to set in FSCR (and HFSCR).
In both cases the value that's configured at boot is not propagated
into the init_task.thread.fscr value prior to the initial fork of init
(pid 1), which means the value is not used by any processes other than
swapper (the idle task).
For the __init_FSCR() case this is OK, because the value in
init_task.thread.fscr is initialised to something sensible. However it
does mean that the value set in __init_FSCR() is not used other than
for swapper, which is odd and confusing.
The bigger problem is for the device tree CPU features case it
prevents firmware from setting (or clearing) FSCR bits for use by user
space. This means all existing kernels can not have features
enabled/disabled by firmware if those features require
setting/clearing FSCR bits.
We can handle both cases by saving the FSCR value into
init_task.thread.fscr after we have initialised it at boot. This fixes
the bug for device tree CPU features, and will allow us to simplify
the initialisation for the __init_FSCR() case in a future patch.
Fixes: 5a61ef74f269 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-3-mpe@ellerman.id.au
|
|
The device tree CPU features binding includes FSCR bit numbers which
Linux is instructed to set by firmware.
Whether that's a good idea or not, in the case of the DSCR the Linux
implementation has a hard requirement that the FSCR_DSCR bit not be
set by default. We use it to track when a process reads/writes to
DSCR, so it must be clear to begin with.
So if firmware tells us to set FSCR_DSCR we must ignore it.
Currently this does not cause a bug in our DSCR handling because the
value of FSCR that the device tree CPU features code establishes is
only used by swapper. All other tasks use the value hard coded in
init_task.thread.fscr.
However we'd like to fix that in a future commit, at which point this
will become necessary.
Fixes: 5a61ef74f269 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-2-mpe@ellerman.id.au
|
|
__init_FSCR() was added originally in commit 2468dcf641e4 ("powerpc:
Add support for context switching the TAR register") (Feb 2013), and
only set FSCR_TAR.
At that point FSCR (Facility Status and Control Register) was not
context switched, so the setting was permanent after boot.
Later we added initialisation of FSCR_DSCR to __init_FSCR(), in commit
54c9b2253d34 ("powerpc: Set DSCR bit in FSCR setup") (Mar 2013), again
that was permanent after boot.
Then commit 2517617e0de6 ("powerpc: Fix context switch DSCR on
POWER8") (Aug 2013) added a limited context switch of FSCR, just the
FSCR_DSCR bit was context switched based on thread.dscr_inherit. That
commit said "This clears the H/FSCR DSCR bit initially", but it
didn't, it left the initialisation of FSCR_DSCR in __init_FSCR().
However the initial context switch from init_task to pid 1 would clear
FSCR_DSCR because thread.dscr_inherit was 0.
That commit also introduced the requirement that FSCR_DSCR be clear
for user processes, so that we can take the facility unavailable
interrupt in order to manage dscr_inherit.
Then in commit 152d523e6307 ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") (Dec 2015) FSCR was added to
thread_struct. However it still wasn't fully context switched, we just
took the existing value and set FSCR_DSCR if the new thread had
dscr_inherit set. FSCR was still initialised at boot to FSCR_DSCR |
FSCR_TAR, but that value was not propagated into the thread_struct, so
the initial context switch set FSCR_DSCR back to 0.
Finally commit b57bd2de8c6c ("powerpc: Improve FSCR init and context
switching") (Jun 2016) added a full context switch of the FSCR, and
added an initialisation of init_task.thread.fscr to FSCR_TAR |
FSCR_EBB, but omitted FSCR_DSCR.
The end result is that swapper runs with FSCR_DSCR set because of the
initialisation in __init_FSCR(), but no other processes do, they use
the value from init_task.thread.fscr.
Having FSCR_DSCR set for swapper allows it to access SPR 3 from
userspace, but swapper never runs userspace, so it has no useful
effect. It's also confusing to have the value initialised in two
places to two different values.
So remove FSCR_DSCR from __init_FSCR(), this at least gets us to the
point where there's a single value of FSCR, even if it's still set in
two places.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-1-mpe@ellerman.id.au
|
|
Since commit c55d7b5e64265f ("powerpc: Remove STRICT_KERNEL_RWX
incompatibility with RELOCATABLE"), powerpc kernels with
-mprofile-kernel can crash in certain scenarios with a trace like below:
BUG: Unable to handle kernel instruction fetch (NULL pointer?)
Faulting instruction address: 0x00000000
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=256 DEBUG_PAGEALLOC NUMA PowerNV
<snip>
NIP [0000000000000000] 0x0
LR [c0080000102c0048] ext4_iomap_end+0x8/0x30 [ext4]
Call Trace:
iomap_apply+0x20c/0x920 (unreliable)
iomap_bmap+0xfc/0x160
ext4_bmap+0xa4/0x180 [ext4]
bmap+0x4c/0x80
jbd2_journal_init_inode+0x44/0x1a0 [jbd2]
ext4_load_journal+0x440/0x860 [ext4]
ext4_fill_super+0x342c/0x3ab0 [ext4]
mount_bdev+0x25c/0x290
ext4_mount+0x28/0x50 [ext4]
legacy_get_tree+0x4c/0xb0
vfs_get_tree+0x4c/0x130
do_mount+0xa18/0xc50
sys_mount+0x158/0x180
system_call+0x5c/0x68
The NIP points to NULL, or a random location (data even), while the LR
always points to the LEP of a function (with an offset of 8), indicating
that something went wrong with ftrace. However, ftrace is not
necessarily active when such crashes occur.
The kernel OOPS sometimes follows a warning from ftrace indicating that
some module functions could not be patched with a nop. Other times, if a
module is loaded early during boot, instruction patching can fail due to
a separate bug, but the error is not reported due to missing error
reporting.
In all the above cases when instruction patching fails, ftrace will be
disabled but certain kernel module functions will be left with default
calls to _mcount(). This is not a problem with ELFv1. However, with
-mprofile-kernel, the default stub is problematic since it depends on a
valid module TOC in r2. If the kernel (or a different module) calls into
a function that does not use the TOC, the function won't have a prologue
to setup the module TOC. When that function calls into _mcount(), we
will end up in the relocation stub that will use the previous TOC, and
end up trying to jump into a random location. From the above trace:
iomap_apply+0x20c/0x920 [kernel TOC]
|
V
ext4_iomap_end+0x8/0x30 [no GEP == kernel TOC]
|
V
_mcount() stub
[uses kernel TOC -> random entry]
To address this, let's change over to using the special stub that is
used for ftrace_[regs_]caller() for _mcount(). This ensures that we are
not dependent on a valid module TOC in r2 for default _mcount()
handling.
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8affd4298d22099bbd82544fab8185700a6222b1.1587488954.git.naveen.n.rao@linux.vnet.ibm.com
|
|
For -mprofile-kernel, we need special handling when generating stubs for
ftrace calls such as _mcount(). To faciliate this, we check if a
R_PPC64_REL24 relocation is for a symbol named "_mcount()" along with
also checking the instruction sequence. The latter is not really
required since "_mcount()" is an exported symbol and kernel modules
cannot use it. As such, drop the additional checking and simplify the
code. This helps unify stub creation for ftrace stubs with
-mprofile-kernel and aids in code reuse.
Also rename is_mprofile_mcount_callsite() to is_mprofile_ftrace_call()
to reflect the checking being done.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7d9c316adfa1fb787ad268bb4691e7e4059ff2d5.1587488954.git.naveen.n.rao@linux.vnet.ibm.com
|
|
module_trampoline_target() is only used by ftrace. Move the prototype
within the appropriate #ifdef in the header. Also, move the function
body to the end of module_64.c so as to consolidate all ftrace code in
one place.
No functional changes.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2527351f65c53c5866068ae130dc34c5d4ee8ad9.1587488954.git.naveen.n.rao@linux.vnet.ibm.com
|
|
kprobe does not handle events happening in real mode.
The very last part of exception exits cannot support a trap.
Blacklist them from kprobe.
While we are at it, remove exc_exit_start symbol which is not
used to avoid having to blacklist it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/098b0fd3f6299aa1bd692bd576bd7012c84608de.1585670437.git.christophe.leroy@c-s.fr
|
|
kprobe does not handle events happening in real mode.
The very last part of syscall cannot support a trap.
Add a symbol syscall_exit_finish to identify that part and
blacklist it from kprobe.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/23eddf49abb03d1359fa0be4206998eb3800f42c.1585670437.git.christophe.leroy@c-s.fr
|
|
kprobe does not handle events happening in real mode.
As exception entry points are running with MMU disabled,
blacklist them.
The handling of TLF_NAPPING and TLF_SLEEPING is moved before the
CONFIG_TRACE_IRQFLAGS which contains 'reenable_mmu' because from there
kprobe will be possible as the kernel will run with MMU enabled.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f61ac599855e674ebb592464d0ea32a3ba9c6644.1585670437.git.christophe.leroy@c-s.fr
|
|
kprobe does not handle events happening in real mode, all
functions running with MMU disabled have to be blacklisted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3bf57066d05518644dee0840af69d36ab5086729.1585670437.git.christophe.leroy@c-s.fr
|
|
machine_check_in_rtas() is just a trap.
Do the trap directly in the machine check exception handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/78899f40f89cb3c4f69bdff7f04eb6ec7cb753d5.1585670437.git.christophe.leroy@c-s.fr
|
|
In order to avoid Oopses, use probe_address() to read the
instruction at the address where the trap happened.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7f24b5961a6839ff01df792816807f74ff236bf6.1582567319.git.christophe.leroy@c-s.fr
|
|
Implement rtas_call_reentrant() for reentrant rtas-calls:
"ibm,int-on", "ibm,int-off",ibm,get-xive" and "ibm,set-xive".
On LoPAPR Version 1.1 (March 24, 2016), from 7.3.10.1 to 7.3.10.4,
items 2 and 3 say:
2 - For the PowerPC External Interrupt option: The * call must be
reentrant to the number of processors on the platform.
3 - For the PowerPC External Interrupt option: The * argument call
buffer for each simultaneous call must be physically unique.
So, these rtas-calls can be called in a lockless way, if using
a different buffer for each cpu doing such rtas call.
For this, it was suggested to add the buffer (struct rtas_args)
in the PACA struct, so each cpu can have it's own buffer.
The PACA struct received a pointer to rtas buffer, which is
allocated in the memory range available to rtas 32-bit.
Reentrant rtas calls are useful to avoid deadlocks in crashing,
where rtas-calls are needed, but some other thread crashed holding
the rtas.lock.
This is a backtrace of a deadlock from a kdump testing environment:
#0 arch_spin_lock
#1 lock_rtas ()
#2 rtas_call (token=8204, nargs=1, nret=1, outputs=0x0)
#3 ics_rtas_mask_real_irq (hw_irq=4100)
#4 machine_kexec_mask_interrupts
#5 default_machine_crash_shutdown
#6 machine_crash_shutdown
#7 __crash_kexec
#8 crash_kexec
#9 oops_end
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
[mpe: Move under #ifdef PSERIES to avoid build breakage]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200518234245.200672-3-leobras.c@gmail.com
|
|
While providing guests, it's desirable to resize it's memory on demand.
By now, it's possible to do so by creating a guest with a small base
memory, hot-plugging all the rest, and using 'movable_node' kernel
command-line parameter, which puts all hot-plugged memory in
ZONE_MOVABLE, allowing it to be removed whenever needed.
But there is an issue regarding guest reboot:
If memory is hot-plugged, and then the guest is rebooted, all hot-plugged
memory goes to ZONE_NORMAL, which offers no guaranteed hot-removal.
It usually prevents this memory to be hot-removed from the guest.
It's possible to use device-tree information to fix that behavior, as
it stores flags for LMB ranges on ibm,dynamic-memory-vN.
It involves marking each memblock with the correct flags as hotpluggable
memory, which mm/memblock.c puts in ZONE_MOVABLE during boot if
'movable_node' is passed.
For carrying such information, the new flag DRCONF_MEM_HOTREMOVABLE was
proposed and accepted into Power Architecture documentation.
This flag should be:
- true (b=1) if the hypervisor may want to hot-remove it later, and
- false (b=0) if it does not care.
During boot, guest kernel reads the device-tree, early_init_drmem_lmb()
is called for every added LMBs. Here, checking for this new flag and
marking memblocks as hotplugable memory is enough to get the desirable
behavior.
This should cause no change if 'movable_node' parameter is not passed
in kernel command-line.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Reviewed-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200402195156.626430-1-leonardo@linux.ibm.com
|
|
Currently when we boot on a big core system, we get this print:
[ 0.040500] Using small cores at SMT level
This is misleading as we've actually detected big cores.
This patch clears up the print to say we've detect big cores but are
using small cores for scheduling.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200528230731.1235752-1-mikey@neuling.org
|
|
If the memory chunk found for reserving memory overshoots the memory
limit imposed, do not proceed with reserving memory. Default behavior
was this until commit 140777a3d8df ("powerpc/fadump: consider reserved
ranges while reserving memory") changed it unwittingly.
Fixes: 140777a3d8df ("powerpc/fadump: consider reserved ranges while reserving memory")
Cc: stable@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/159057266320.22331.6571453892066907320.stgit@hbathini.in.ibm.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"Assorted patches from Miklos.
An interesting part here is /proc/mounts stuff..."
The "/proc/mounts stuff" is using a cursor for keeeping the location
data while traversing the mount listing.
Also probably worth noting is the addition of faccessat2(), which takes
an additional set of flags to specify how the lookup is done
(AT_EACCESS, AT_SYMLINK_NOFOLLOW, AT_EMPTY_PATH).
* 'from-miklos' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: add faccessat2 syscall
vfs: don't parse "silent" option
vfs: don't parse "posixacl" option
vfs: don't parse forbidden flags
statx: add mount_root
statx: add mount ID
statx: don't clear STATX_ATIME on SB_RDONLY
uapi: deprecate STATX_ALL
utimensat: AT_EMPTY_PATH support
vfs: split out access_override_creds()
proc/mounts: add cursor
aio: fix async fsync creds
vfs: allow unprivileged whiteout creation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The RCU updates for this cycle were:
- RCU-tasks update, including addition of RCU Tasks Trace for BPF use
and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates"
* tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
rcu: Allow for smp_call_function() running callbacks from idle
rcu: Provide rcu_irq_exit_check_preempt()
rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()
rcu: Provide __rcu_is_watching()
rcu: Provide rcu_irq_exit_preempt()
rcu: Make RCU IRQ enter/exit functions rely on in_nmi()
rcu/tree: Mark the idle relevant functions noinstr
x86: Replace ist_enter() with nmi_enter()
x86/mce: Send #MC singal from task work
x86/entry: Get rid of ist_begin/end_non_atomic()
sched,rcu,tracing: Avoid tracing before in_nmi() is correct
sh/ftrace: Move arch_ftrace_nmi_{enter,exit} into nmi exception
lockdep: Always inline lockdep_{off,on}()
hardirq/nmi: Allow nested nmi_enter()
arm64: Prepare arch_nmi_enter() for recursion
printk: Disallow instrumenting print_nmi_enter()
printk: Prepare for nested printk_nmi_enter()
rcutorture: Convert ULONG_CMP_LT() to time_before()
torture: Add a --kasan argument
torture: Save a few lines by using config_override_param initially
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull kprobes updates from Ingo Molnar:
"Various kprobes updates, mostly centered around cleaning up the
no-instrumentation logic.
Instead of the current per debug facility blacklist, use the more
generic .noinstr.text approach, combined with a 'noinstr' marker for
functions.
Also add instrumentation_begin()/end() to better manage the exact
place in entry code where instrumentation may be used.
And add a kprobes blacklist for modules"
* tag 'core-kprobes-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Prevent probes in .noinstr.text section
vmlinux.lds.h: Create section for protection against instrumentation
samples/kprobes: Add __kprobes and NOKPROBE_SYMBOL() for handlers.
kprobes: Support NOKPROBE_SYMBOL() in modules
kprobes: Support __kprobes blacklist in modules
kprobes: Lock kprobe_mutex while showing kprobe_blacklist
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
|
|
To turn the KMSG_DUMP_* reasons into a more ordered list, collapse
the redundant KMSG_DUMP_(RESTART|HALT|POWEROFF) reasons into
KMSG_DUMP_SHUTDOWN. The current users already don't meaningfully
distinguish between them, so there's no need to, as discussed here:
https://lore.kernel.org/lkml/CA+CK2bAPv5u1ih5y9t5FUnTyximtFCtDYXJCpuyjOyHNOkRdqw@mail.gmail.com/
Link: https://lore.kernel.org/lkml/20200515184434.8470-2-keescook@chromium.org/
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
syzkaller is picking up a bunch of crashes that look like this:
Unrecoverable exception 380 at c00000000037ed60 (msr=8000000000001031)
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 874 Comm: syz-executor.0 Not tainted 5.7.0-rc7-syzkaller-00016-gb0c3ba31be3e #0
NIP: c00000000037ed60 LR: c00000000004bac8 CTR: c000000000030990
REGS: c0000000555a7230 TRAP: 0380 Not tainted (5.7.0-rc7-syzkaller-00016-gb0c3ba31be3e)
MSR: 8000000000001031 <SF,ME,IR,DR,LE> CR: 48222882 XER: 20000000
CFAR: c00000000004bac4 IRQMASK: 0
GPR00: c00000000004bb68 c0000000555a74c0 c0000000024b3500 0000000000000005
GPR04: 0000000000000000 0000000000000000 c00000000004bb88 c008000000910000
GPR08: 00000000000b0000 c00000000004bac8 0000000000016000 c000000002503500
GPR12: c000000000030990 c000000003190000 00000000106a5898 00000000106a0000
GPR16: 00000000106a5890 c000000007a92000 c000000008180e00 c000000007a8f700
GPR20: c000000007a904b0 0000000010110000 c00000000259d318 5deadbeef0000100
GPR24: 5deadbeef0000122 c000000078422700 c000000009ee88b8 c000000078422778
GPR28: 0000000000000001 800000000280b033 0000000000000000 c0000000555a75a0
NIP [c00000000037ed60] __sanitizer_cov_trace_pc+0x40/0x50
LR [c00000000004bac8] interrupt_exit_kernel_prepare+0x118/0x310
Call Trace:
[c0000000555a74c0] [c00000000004bb68] interrupt_exit_kernel_prepare+0x1b8/0x310 (unreliable)
[c0000000555a7530] [c00000000000f9a8] interrupt_return+0x118/0x1c0
--- interrupt: 900 at __sanitizer_cov_trace_pc+0x0/0x50
...<random previous call chain>...
This is caused by __sanitizer_cov_trace_pc() causing an SLB fault
after MSR[RI] has been cleared by __hard_EE_RI_disable(), which we
can not recover from.
Do not instrument the new syscall/interrupt entry/exit code with KCOV,
GCOV or UBSAN.
Reported-by: syzbot-ppc64 <ozlabsyz@au1.ibm.com>
Fixes: 68b34588e202 ("powerpc/64/sycall: Implement syscall entry/exit logic in C")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Similar to the C code change, make the AMR restore conditional on
whether the register has changed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200429065654.1677541-7-npiggin@gmail.com
|
|
The AMR update is made conditional on AMR actually changing, which
should be the less common case on most workloads (though kernel page
faults on uaccess could be frequent, this doesn't significantly slow
down that case).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200429065654.1677541-4-npiggin@gmail.com
|
|
We have r12 available, use it to keep CR around and don't
save it in SPRN_SPRG_SCRATCH6.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/019f314a98c107c4ca46e46c1cf402e9a44114a7.1590079969.git.christophe.leroy@csgroup.eu
|
|
Let's reduce the number of registers used in TLB miss handlers.
We have both r9 and r12 available for any temporary use.
r9 is enough, avoid using r12.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7f330e971952abb2645fb9ca4310c0f527e84dcb.1590079969.git.christophe.leroy@csgroup.eu
|
|
This erratum is dedicated to IBM 405GP and STB03xxx
which are now gone.
Remove this erratum.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/44dbc08e9034681eb28324cbabc086e97044c36c.1590079969.git.christophe.leroy@csgroup.eu
|
