summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/configs/cell_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2014-10-03powerpc: Don't build powernv for other platform defconfigsMichael Ellerman1-0/+1
Because powernv arrived after these other platforms, the defconfigs didn't have PPC_POWERNV disabled, and being default y it gets turned on. If we're going to bother having defconfigs for the specific platforms then they should only build the code required for those platforms. The grab bag of everything config is ppc64_defconfig. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-09-09powerpc: Make CONFIG_FHANDLE=y for all 64 bit powerpc defconfigsCyril Bur1-0/+1
CONFIG_FHANDLE is a requirement for systemd and with the increasing uptake of systemd within distros it makes sense for 64 bit defconfigs to include it. Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
2014-05-27USB: delete CONFIG_USB_DEVICEFS from defconfigNaoki MATSUMOTO1-1/+0
It no longer occurs in Kconfig. USB: remove CONFIG_USB_DEVICEFS(fb28d58b) leaked remove defconfig. Signed-off-by: Naoki MATSUMOTO <nekomatu+linux@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2010-08-09powerpc: Trim defconfigsBenjamin Herrenschmidt1-1308/+9
This trims all our defconfigs using make savedefconfig Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-06-15powerpc: Disable CONFIG_SYSFS_DEPRECATEDGrant Likely1-2/+1
Acked-by: Grant Likely <grant.likely@secretlab.ca> On 5 May 2010 21:33, "Anton Blanchard" <anton@samba.org> wrote: CONFIG_SYSFS_DEPRECATED can cause issues with newer distros and should not be required for any distro in the last 3 or 4 years, so disable it. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-26eeprom: More consistent symbol namesJean Delvare1-1/+1
Now that all EEPROM drivers live in the same place, let's harmonize their symbol names. Also fix eeprom's dependencies, it definitely needs sysfs, and is no longer experimental after many years in the kernel tree. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: David Brownell <dbrownell@users.sourceforge.net>
2008-03-20[POWERPC] Update some defconfigsPaul Mackerras1-55/+86
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-12-06[POWERPC] Update defconfigsPaul Mackerras1-77/+99
This updates all the defconfigs in arch/powerpc/configs except iseries and ps3, which were updated by the preceding commits. This mostly takes the defaults, except that I turned on tickless idle and high-resolution timers for everything, and turned off instrumentation support and "Fair group CPU scheduler" for the smaller/embedded platforms. Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-10-19task cgroups: enable cgroups by default in some configsPaul Jackson1-0/+1
In pre-cgroup cpusets, a few config files enabled cpusets by default. Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-25[POWERPC] cell: Update cell_defconfig for 2.6.23Arnd Bergmann1-144/+76
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-07-20[CELL] oprofile: add support to OProfile for profiling CELL BE SPUsBob Nelson1-1/+2
From: Maynard Johnson <mpjohn@us.ibm.com> This patch updates the existing arch/powerpc/oprofile/op_model_cell.c to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code. Exports spu_set_profile_private_kref and spu_get_profile_private_kref which are used by OProfile to store private profile information in spufs data structures. Also incorporated several fixes from other patches (rrn). Check pointer returned from kzalloc. Eliminated unnecessary cast. Better error handling and cleanup in the related area. 64-bit unsigned long parameter was being demoted to 32-bit unsigned int and eventually promoted back to unsigned long. Signed-off-by: Carl Love <carll@us.ibm.com> Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com> Signed-off-by: Bob Nelson <rrnelson@us.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org>
2007-06-26[POWERPC] Update defconfigsPaul Mackerras1-140/+103
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-17[POWERPC] cell_defconfig: Disable cpufreq and pmiChristian Krafft1-14/+1
Cpufreq using pmi is broken by a dependency issue, that will be fixed in a seperate patch. Bare-metal cpufreq is broken by hardware limitations. As it was the only user, pmi is disabled as well. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-23[POWERPC] update cell_defconfigArnd Bergmann1-28/+29
Sync with the Kconfig changes, and enable some options for celleb Cc: Ishizaki Kou <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jens Osterkamp <jens@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2007-03-10[POWERPC] update cell_defconfigArnd Bergmann1-21/+130
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2007-02-16[POWERPC] Add PMI driver for cell bladeChristian Krafft1-0/+1
This adds driver code for the PMI device found in future IBM products. PMI stands for "Platform Management Interrupt" and is a way to communicate with the BMC (Baseboard Management Controller). It provides bidirectional communication with a low latency. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Acked-by: Heiko J Schick <schickhj@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-22[POWERPC] Update defconfigsPaul Mackerras1-4/+2
Mostly took the defaults, except tried to get the netfilter options more or less as they were before. Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-19[POWERPC] cell: update cell_defconfigArnd Bergmann1-44/+314
New options appeared in the kernel, and new hardware became available for us to use. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2006-12-04[POWERPC] update cell_defconfig for ps3 supportArnd Bergmann1-8/+23
In the common cell kernel, I want to have ps3 enabled to find potential bugs at compile-time. Also enable SPU disassembly in xmon. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
2006-12-04[POWERPC] cell: Add oprofile supportMaynard Johnson1-1/+2
Add PPU event-based and cycle-based profiling support to Oprofile for Cell. Oprofile is expected to collect data on all CPUs simultaneously. However, there is one set of performance counters per node. There are two hardware threads or virtual CPUs on each node. Hence, OProfile must multiplex in time the performance counter collection on the two virtual CPUs. The multiplexing of the performance counters is done by a virtual counter routine. Initially, the counters are configured to collect data on the even CPUs in the system, one CPU per node. In order to capture the PC for the virtual CPU when the performance counter interrupt occurs (the specified number of events between samples has occurred), the even processors are configured to handle the performance counter interrupts for their node. The virtual counter routine is called via a kernel timer after the virtual sample time. The routine stops the counters, saves the current counts, loads the last counts for the other virtual CPU on the node, sets interrupts to be handled by the other virtual CPU and restarts the counters, the virtual timer routine is scheduled to run again. The virtual sample time is kept relatively small to make sure sampling occurs on both CPUs on the node with a relatively small granularity. Whenever the counters overflow, the performance counter interrupt is called to collect the PC for the CPU where data is being collected. The oprofile driver relies on a firmware RTAS call to setup the debug bus to route the desired signals to the performance counter hardware to be counted. The RTAS call must set the routing registers appropriately in each of the islands to pass the signals down the debug bus as well as routing the signals from a particular island onto the bus. There is a second firmware RTAS call to reset the debug bus to the non pass thru state when the counters are not in use. Signed-off-by: Carl Love <carll@us.ibm.com> Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-04Merge branch 'linux-2.6' into for-linusPaul Mackerras1-6/+13
2006-10-25[POWERPC] cell: add cpufreq driver for Cell BE processorChristian Krafft1-1/+14
This patch adds a cpufreq backend driver to enable frequency scaling on cell. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-25[POWERPC] cell: add temperature to SPU and CPU sysfs entriesChristian Krafft1-0/+1
This patch adds a module that registers sysfs attributes to CPU and SPU containing the temperature of the CBE. They can be found under /sys/devices/system/spu/cpuX/thermal/temperature[0|1] /sys/devices/system/spu/spuX/thermal/temperature The temperature is read from the on-chip temperature sensors. Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-25[POWERPC] cell: update defconfigArnd Bergmann1-6/+13
=================================================================== Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-05[POWERPC] Update cell_defconfigArnd Bergmann1-14/+46
This adds defaults for new configuration options added since 2.6.18 and it enables the option for 64kb pages by default. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-09-10[POWERPC] Update defconfigsPaul Mackerras1-7/+51
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-28[POWERPC] Enable XMON in cell_defconfigMichael Ellerman1-3/+4
Now that we have the udbg callbacks we can enable XMON by default. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-21[POWERPC] spufs: split the Cell BE support into generic and platform ↵Geoff Levand1-1/+3
dependant parts Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE. The existing CONFIG_PPC_CELL is now used to denote the generic Cell processor support. PPC_CELL = make descends into platforms/cell PPC_CELL_NATIVE = add bare metal support PPC_IBM_CELL_BLADE = add blade device drivers, etc. Also renames spu_priv1.c to spu_priv1_mmio.c. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-21[POWERPC] cell: update defconfigarnd@arndb.de1-12/+17
Enable some of the most requested features in defconfig and refresh with the latest powerpc.git Kconfig files. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-06-21[POWERPC] cell: add RAS supportBenjamin Herrenschmidt1-0/+1
This is a first version of support for the Cell BE "Reliability, Availability and Serviceability" features. It doesn't yet handle some of the RAS interrupts (the ones described in iic_is/iic_irr), I'm still working on a proper way to expose these. They are essentially a cascaded controller by themselves (sic !) though I may just handle them locally to the iic driver. I need also to sync with David Erb on the way he hooked in the performance monitor interrupt. So that's all for 2.6.17 and I'll do more work on that with my rework of the powerpc interrupt layer that I'm hacking on at the moment. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-04-29[PATCH] powerpc: update cell_defconfigArnd Bergmann1-15/+25
reflect the changes to Kconfig since the last update. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-03-27[PATCH] powerpc: update cell defconfigArnd Bergmann1-81/+52
The default configuration in mainline got a little out of sync with what we use internally. Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-03-16powerpc: update defconfigsPaul Mackerras1-28/+66
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-01-18[PATCH] e1000: Added disable packet split capabilityJesse Brandeburg1-0/+1
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: John Ronciak <john.ronciak@intel.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-12-20powerpc: update defconfigsPaul Mackerras1-3/+4
Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-16[PATCH] powerpc: update defconfigsBenjamin Herrenschmidt1-60/+115
My patch moving ppc64 RTC to genrtc was supposed to update all defconfigs, but for some reason, the patch actually posted only had the pseries one... ouch. This patch properly updates all defconfigs. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-11-03powerpc: Copy default configs into arch/powerpc/configsMichael Ellerman1-0/+1024
Copy default configs into arch/powerpc/configs, rename bpa_defconfig to cell_defconfig while we're at it. Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-07 18:11:45 +0000