| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When CPU hotplugging is enabled, the user may want to remove the
current CPU which is providing the timer ticks. If this happens
we need to find a new timesync master.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add relevant code to __cpu_die() and __cpu_disable() to finally enable
the CPU hotplugging features. Reset the irq count values in smp_callin()
to zero before bringing up the CPU.
It seems that the firmware may need up to 8 seconds to fully stop a CPU
in which no other PDC calls are allowed to be made. Use a timeout
__cpu_die() to accommodate for this.
Use "chcpu -d 1" to bring CPU1 down, and "chcpu -e 1" to bring it up.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add pdc_cpu_rendezvous_lock() and pdc_cpu_rendezvous_unlock()
to lock PDC while CPU is transitioning into rendezvous state.
This is needed, because the transition phase may take up to 8 seconds.
Add pdc_pat_get_PDC_entrypoint() to get PDC entry point for current CPU.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Switch away from the own cpu topology code to common code which is used
by ARM64 and RISCV. That will allow us to enable CPU hotplug later on.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Clean up the code for the mfctl() and mtctl() functions and add often
used constants.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Merge yet more updates from Andrew Morton:
"This is the material which was staged after willystuff in linux-next.
Subsystems affected by this patch series: mm (debug, selftests,
pagecache, thp, rmap, migration, kasan, hugetlb, pagemap, madvise),
and selftests"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (113 commits)
selftests: kselftest framework: provide "finished" helper
mm: madvise: MADV_DONTNEED_LOCKED
mm: fix race between MADV_FREE reclaim and blkdev direct IO read
mm: generalize ARCH_HAS_FILTER_PGPROT
mm: unmap_mapping_range_tree() with i_mmap_rwsem shared
mm: warn on deleting redirtied only if accounted
mm/huge_memory: remove stale locking logic from __split_huge_pmd()
mm/huge_memory: remove stale page_trans_huge_mapcount()
mm/swapfile: remove stale reuse_swap_page()
mm/khugepaged: remove reuse_swap_page() usage
mm/huge_memory: streamline COW logic in do_huge_pmd_wp_page()
mm: streamline COW logic in do_swap_page()
mm: slightly clarify KSM logic in do_swap_page()
mm: optimize do_wp_page() for fresh pages in local LRU pagevecs
mm: optimize do_wp_page() for exclusive pages in the swapcache
mm/huge_memory: make is_transparent_hugepage() static
userfaultfd/selftests: enable hugetlb remap and remove event testing
selftests/vm: add hugetlb madvise MADV_DONTNEED MADV_REMOVE test
mm: enable MADV_DONTNEED for hugetlb mappings
kasan: disable LOCKDEP when printing reports
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Livepatch support for 32-bit is probably the standout new feature,
otherwise mostly just lots of bits and pieces all over the board.
There's a series of commits cleaning up function descriptor handling,
which touches a few other arches as well as LKDTM. It has acks from
Arnd, Kees and Helge.
Summary:
- Enforce kernel RO, and implement STRICT_MODULE_RWX for 603.
- Add support for livepatch to 32-bit.
- Implement CONFIG_DYNAMIC_FTRACE_WITH_ARGS.
- Merge vdso64 and vdso32 into a single directory.
- Fix build errors with newer binutils.
- Add support for UADDR64 relocations, which are emitted by some
toolchains. This allows powerpc to build with the latest lld.
- Fix (another) potential userspace r13 corruption in transactional
memory handling.
- Cleanups of function descriptor handling & related fixes to LKDTM.
Thanks to Abdul Haleem, Alexey Kardashevskiy, Anders Roxell, Aneesh
Kumar K.V, Anton Blanchard, Arnd Bergmann, Athira Rajeev, Bhaskar
Chowdhury, Cédric Le Goater, Chen Jingwen, Christophe JAILLET,
Christophe Leroy, Corentin Labbe, Daniel Axtens, Daniel Henrique
Barboza, David Dai, Fabiano Rosas, Ganesh Goudar, Guo Zhengkui, Hangyu
Hua, Haren Myneni, Hari Bathini, Igor Zhbanov, Jakob Koschel, Jason
Wang, Jeremy Kerr, Joachim Wiberg, Jordan Niethe, Julia Lawall, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mamatha Inamdar,
Maxime Bizon, Maxim Kiselev, Maxim Kochetkov, Michal Suchanek,
Nageswara R Sastry, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Nour-eddine Taleb, Paul Menzel, Ping Fang, Pratik R. Sampat, Randy
Dunlap, Ritesh Harjani, Rohan McLure, Russell Currey, Sachin Sant,
Segher Boessenkool, Shivaprasad G Bhat, Sourabh Jain, Thierry Reding,
Tobias Waldekranz, Tyrel Datwyler, Vaibhav Jain, Vladimir Oltean,
Wedson Almeida Filho, and YueHaibing"
* tag 'powerpc-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc/pseries: Fix use after free in remove_phb_dynamic()
powerpc/time: improve decrementer clockevent processing
powerpc/time: Fix KVM host re-arming a timer beyond decrementer range
powerpc/tm: Fix more userspace r13 corruption
powerpc/xive: fix return value of __setup handler
powerpc/64: Add UADDR64 relocation support
powerpc: 8xx: fix a return value error in mpc8xx_pic_init
powerpc/ps3: remove unneeded semicolons
powerpc/64: Force inlining of prevent_user_access() and set_kuap()
powerpc/bitops: Force inlining of fls()
powerpc: declare unmodified attribute_group usages const
powerpc/spufs: Fix build warning when CONFIG_PROC_FS=n
powerpc/secvar: fix refcount leak in format_show()
powerpc/64e: Tie PPC_BOOK3E_64 to PPC_FSL_BOOK3E
powerpc: Move C prototypes out of asm-prototypes.h
powerpc/kexec: Declare kexec_paca static
powerpc/smp: Declare current_set static
powerpc: Cleanup asm-prototypes.c
powerpc/ftrace: Use STK_GOT in ftrace_mprofile.S
powerpc/ftrace: Regroup PPC64 specific operations in ftrace_mprofile.S
...
|
|
MADV_DONTNEED historically rejects mlocked ranges, but with MLOCK_ONFAULT
and MCL_ONFAULT allowing to mlock without populating, there are valid use
cases for depopulating locked ranges as well.
Users mlock memory to protect secrets. There are allocators for secure
buffers that want in-use memory generally mlocked, but cleared and
invalidated memory to give up the physical pages. This could be done with
explicit munlock -> mlock calls on free -> alloc of course, but that adds
two unnecessary syscalls, heavy mmap_sem write locks, vma splits and
re-merges - only to get rid of the backing pages.
Users also mlockall(MCL_ONFAULT) to suppress sustained paging, but are
okay with on-demand initial population. It seems valid to selectively
free some memory during the lifetime of such a process, without having to
mess with its overall policy.
Why add a separate flag? Isn't this a pretty niche usecase?
- MADV_DONTNEED has been bailing on locked vmas forever. It's at least
conceivable that someone, somewhere is relying on mlock to protect
data from perhaps broader invalidation calls. Changing this behavior
now could lead to quiet data corruption.
- It also clarifies expectations around MADV_FREE and maybe
MADV_REMOVE. It avoids the situation where one quietly behaves
different than the others. MADV_FREE_LOCKED can be added later.
- The combination of mlock() and madvise() in the first place is
probably niche. But where it happens, I'd say that dropping pages
from a locked region once they don't contain secrets or won't page
anymore is much saner than relying on mlock to protect memory from
speculative or errant invalidation calls. It's just that we can't
change the default behavior because of the two previous points.
Given that, an explicit new flag seems to make the most sense.
[hannes@cmpxchg.org: fix mips build]
Link: https://lkml.kernel.org/r/20220304171912.305060-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
"Lots of small fixes and code cleanups across most of the fbdev
drivers.
This includes conversions to use helper functions, const conversions,
spelling fixes, help text updates, adding return value checks, small
build fixes, and much more"
* tag 'for-5.18/fbdev-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (59 commits)
video: fbdev: kyro: make read-only array ODValues static const
video: fbdev: offb: fix warning comparing pointer to 0
video: fbdev: omapfb: Add missing of_node_put() in dvic_probe_of
video: fbdev: sm712fb: Fix crash in smtcfb_write()
video: fbdev: s3c-fb: fix platform_get_irq.cocci warning
video: fbdev: sm712fb: Fix crash in smtcfb_read()
video: fbdev: via: check the return value of kstrdup()
video: fbdev: au1100fb: Spelling s/palette/palette/
video: fbdev: atari: Atari 2 bpp (STe) palette bugfix
video: fbdev: atari: Remove unused atafb_setcolreg()
video: fbdev: atari: Convert to standard round_up() helper
video: fbdev: atari: Fix TT High video mode
video: fbdev: udlfb: replace snprintf in show functions with sysfs_emit
video: fbdev: omapfb: panel-tpo-td043mtea1: Use sysfs_emit() instead of snprintf()
video: fbdev: omapfb: panel-dsi-cm: Use sysfs_emit() instead of snprintf()
video: fbdev: omapfb: Use sysfs_emit() instead of snprintf()
video: fbdev: s3c-fb: Use platform_get_irq() to get the interrupt
video: fbdev: Fix wrong file path for pvr2fb.c in Kconfig help text
video: fbdev: pxa3xx-gcu: Remove unnecessary print function dev_err()
video: fbdev: pxa168fb: Remove unnecessary print function dev_err()
...
|
|
Pull folio updates from Matthew Wilcox:
- Rewrite how munlock works to massively reduce the contention on
i_mmap_rwsem (Hugh Dickins):
https://lore.kernel.org/linux-mm/8e4356d-9622-a7f0-b2c-f116b5f2efea@google.com/
- Sort out the page refcount mess for ZONE_DEVICE pages (Christoph
Hellwig):
https://lore.kernel.org/linux-mm/20220210072828.2930359-1-hch@lst.de/
- Convert GUP to use folios and make pincount available for order-1
pages. (Matthew Wilcox)
- Convert a few more truncation functions to use folios (Matthew
Wilcox)
- Convert page_vma_mapped_walk to use PFNs instead of pages (Matthew
Wilcox)
- Convert rmap_walk to use folios (Matthew Wilcox)
- Convert most of shrink_page_list() to use a folio (Matthew Wilcox)
- Add support for creating large folios in readahead (Matthew Wilcox)
* tag 'folio-5.18c' of git://git.infradead.org/users/willy/pagecache: (114 commits)
mm/damon: minor cleanup for damon_pa_young
selftests/vm/transhuge-stress: Support file-backed PMD folios
mm/filemap: Support VM_HUGEPAGE for file mappings
mm/readahead: Switch to page_cache_ra_order
mm/readahead: Align file mappings for non-DAX
mm/readahead: Add large folio readahead
mm: Support arbitrary THP sizes
mm: Make large folios depend on THP
mm: Fix READ_ONLY_THP warning
mm/filemap: Allow large folios to be added to the page cache
mm: Turn can_split_huge_page() into can_split_folio()
mm/vmscan: Convert pageout() to take a folio
mm/vmscan: Turn page_check_references() into folio_check_references()
mm/vmscan: Account large folios correctly
mm/vmscan: Optimise shrink_page_list for non-PMD-sized folios
mm/vmscan: Free non-shmem folios without splitting them
mm/rmap: Constify the rmap_walk_control argument
mm/rmap: Convert rmap_walk() to take a folio
mm: Turn page_anon_vma() into folio_anon_vma()
mm/rmap: Turn page_lock_anon_vma_read() into folio_lock_anon_vma_read()
...
|
|
We need to use this function in common code, so define it for
architectures and/or configrations that miss it. The result of
pmd_pfn() will only be used if TRANSPARENT_HUGEPAGE is enabled,
but a function or macro called pmd_pfn() must be defined, even
on machines with two level page tables.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
This patch changes the kprobe and kretprobe feature to use another
break instruction instead of relying on the hardware single-step
feature.
That way those kprobes now work in qemu as well, because in qemu we
don't emulate yet single-stepping.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
At least the qemu virtual machine does not provide D- and I-caches,
so skip triggering SMP irqs to flush caches on such machines.
Further optimize the caching code by using static branches and making
some functions static.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The get_current() code uses the mfctl() macro to get the pointer to the
current task struct from %cr30. The problem with the mfctl() macro is,
that it is marked volatile which is basically correct, because mfctl()
is used to get e.g. the current internal timer or interrupt flags as
well.
But specifically the task struct pointer (%cr30) doesn't change over
time when the kernel executes code for a task.
So, by dropping the volatile when retrieving %cr30 the compiler is now
able to get this value only once and optimize the generated code a lot.
A bloat-o-meter comparism shows that this patch saves ~5kB kernel code
on a 32-bit kernel and ~6kB kernel code on a 64-bit kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Use the provided space register constants instead of hardcoded values.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Instead of hardcoding the space registers as strings, use the SR_USER
and SR_KERNEL constants to form the space register in the access
functions.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Provide defines for space registers (SR_KERNEL, SR_USER, ...) which
should be used instead of hardcoding the values.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add minimal vDSO support, which provides the signal trampoline helpers,
but none of the userspace syscall helpers like time wrappers.
The big benefit of this vDSO implementation is, that we now don't need
an executeable stack any longer. PA-RISC is one of the last
architectures where an executeable stack was needed in oder to implement
the signal trampolines by putting assembly instructions on the stack
which then gets executed. Instead the kernel will provide the relevant
code in the vDSO page and only put the pointers to the signal
information on the stack.
By dropping the need for executable stacks we avoid running into issues
with applications which want non executable stacks for security reasons.
Additionally, alternative stacks on memory areas without exec
permissions are supported too.
This code is based on an initial implementation by Randolph Chung from 2006:
https://lore.kernel.org/linux-parisc/4544A34A.6080700@tausq.org/
I did the porting and lifted the code to current code base. Dave fixed
the unwind code so that gdb and glibc are able to backtrace through the
code. An additional patch to gdb will be pushed upstream by Dave.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Cc: Randolph Chung <randolph@tausq.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Currently, the parisc kernel does not fully support non-access TLB
fault handling for probe instructions. In the fast path, we set the
target register to zero if it is not a shadowed register. The slow
path is not implemented, so we call do_page_fault. The architecture
indicates that non-access faults should not cause a page fault from
disk.
This change adds to code to provide non-access fault support for
probe instructions. It also modifies the handling of faults on
userspace so that if the address lies in a valid VMA and the access
type matches that for the VMA, the probe target register is set to
one. Otherwise, the target register is set to zero.
This was done to make probe instructions more useful for userspace.
Probe instructions are not very useful if they set the target register
to zero whenever a page is not present in memory. Nominally, the
purpose of the probe instruction is determine whether read or write
access to a given address is allowed.
This fixes a problem in function pointer comparison noticed in the
glibc testsuite (stdio-common/tst-vfprintf-user-type). The same
problem is likely in glibc (_dl_lookup_address).
V2 adds flush and lpa instruction support to handle_nadtlb_fault.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic into asm-generic
Christoph Hellwig and a few others spent a huge effort on removing
set_fs() from most of the important architectures, but about half the
other architectures were never completed even though most of them don't
actually use set_fs() at all.
I did a patch for microblaze at some point, which turned out to be fairly
generic, and now ported it to most other architectures, using new generic
implementations of access_ok() and __{get,put}_kernel_nocheck().
Three architectures (sparc64, ia64, and sh) needed some extra work,
which I also completed.
* 'set_fs-4' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
uaccess: fix integer overflow on access_ok()
|
|
There are no remaining callers of set_fs(), so CONFIG_SET_FS
can be removed globally, along with the thread_info field and
any references to it.
This turns access_ok() into a cheaper check against TASK_SIZE_MAX.
As CONFIG_SET_FS is now gone, drop all remaining references to
set_fs()/get_fs(), mm_segment_t, user_addr_max() and uaccess_kernel().
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for sparc32 changes
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Tested-by: Sergey Matyukevich <sergey.matyukevich@synopsys.com> # for arc changes
Acked-by: Stafford Horne <shorne@gmail.com> # [openrisc, asm-generic]
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There are many different ways that access_ok() is defined across
architectures, but in the end, they all just compare against the
user_addr_max() value or they accept anything.
Provide one definition that works for most architectures, checking
against TASK_SIZE_MAX for user processes or skipping the check inside
of uaccess_kernel() sections.
For architectures without CONFIG_SET_FS(), this should be the fastest
check, as it comes down to a single comparison of a pointer against a
compile-time constant, while the architecture specific versions tend to
do something more complex for historic reasons or get something wrong.
Type checking for __user annotations is handled inconsistently across
architectures, but this is easily simplified as well by using an inline
function that takes a 'const void __user *' argument. A handful of
callers need an extra __user annotation for this.
Some architectures had trick to use 33-bit or 65-bit arithmetic on the
addresses to calculate the overflow, however this simpler version uses
fewer registers, which means it can produce better object code in the
end despite needing a second (statically predicted) branch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Rutland <mark.rutland@arm.com> [arm64, asm-generic]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Nine architectures are still missing __{get,put}_kernel_nofault:
alpha, ia64, microblaze, nds32, nios2, openrisc, sh, sparc32, xtensa.
Add a generic version that lets everything use the normal
copy_{from,to}_kernel_nofault() code based on these, removing the last
use of get_fs()/set_fs() from architecture-independent code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asm/shmbuf.h is currently excluded from the UAPI compile-test because of
the errors like follows:
HDRTEST usr/include/asm/shmbuf.h
In file included from ./usr/include/asm/shmbuf.h:6,
from <command-line>:
./usr/include/asm-generic/shmbuf.h:26:33: error: field ‘shm_perm’ has incomplete type
26 | struct ipc64_perm shm_perm; /* operation perms */
| ^~~~~~~~
./usr/include/asm-generic/shmbuf.h:27:9: error: unknown type name ‘size_t’
27 | size_t shm_segsz; /* size of segment (bytes) */
| ^~~~~~
./usr/include/asm-generic/shmbuf.h:40:9: error: unknown type name ‘__kernel_pid_t’
40 | __kernel_pid_t shm_cpid; /* pid of creator */
| ^~~~~~~~~~~~~~
./usr/include/asm-generic/shmbuf.h:41:9: error: unknown type name ‘__kernel_pid_t’
41 | __kernel_pid_t shm_lpid; /* pid of last operator */
| ^~~~~~~~~~~~~~
The errors can be fixed by replacing size_t with __kernel_size_t and by
including proper headers.
Then, remove the no-header-test entry from user/include/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
linux/signal.h and asm/signal.h are currently excluded from the UAPI
compile-test because of the errors like follows:
HDRTEST usr/include/asm/signal.h
In file included from <command-line>:
./usr/include/asm/signal.h:103:9: error: unknown type name ‘size_t’
103 | size_t ss_size;
| ^~~~~~
The errors can be fixed by replacing size_t with __kernel_size_t.
Then, remove the no-header-test entries from user/include/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
dereference_function_descriptor() and
dereference_kernel_function_descriptor() are identical on the
three architectures implementing them.
Make them common and put them out-of-line in kernel/extable.c
which is one of the users and has similar type of functions.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/449db09b2eba57f4ab05f80102a67d8675bc8bcd.1644928018.git.christophe.leroy@csgroup.eu
|
|
We have three architectures using function descriptors, each with its
own type and name.
Add a common typedef that can be used in generic code.
Also add a stub typedef for architecture without function descriptors,
to avoid a forest of #ifdefs.
It replaces the similar 'func_desc_t' previously defined in
arch/powerpc/kernel/module_64.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f1f91b142b3c1082bdc1586ce71c9bac1e75213c.1644928018.git.christophe.leroy@csgroup.eu
|
|
Replace HAVE_DEREFERENCE_FUNCTION_DESCRIPTOR by a config option
named CONFIG_HAVE_FUNCTION_DESCRIPTORS and use it instead of
'dereference_function_descriptor' macro to know whether an
arch has function descriptors.
To limit churn in one of the following patches, use
an #ifdef/#else construct with empty first part
instead of an #ifndef in asm-generic/sections.h
On powerpc, make sure the config option matches the ABI used
by the compiler with a BUILD_BUG_ON() and add missing _CALL_ELF=2
when calling 'sparse' so that sparse sees the same piece of
code as GCC.
And include a helper to check whether an arch has function
descriptors or not : have_function_descriptors()
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4a0f11fb0ea74a3197bc44dd7ba25e53a24fd03d.1644928018.git.christophe.leroy@csgroup.eu
|
|
After commit 4b9d2a731c3d ("parisc: Switch user access functions
to signal errors in r29 instead of r8") bash suddenly started
to report those warnings after login:
-bash: cannot set terminal process group (-1): Bad file descriptor
-bash: no job control in this shell
It turned out, that a function call inside a put_user(), e.g.:
put_user(vt_do_kdgkbmode(console), (int __user *)arg);
clobbered the error register (r29) and thus the put_user() call itself
seem to have failed.
Rearrange the C-code to pre-calculate the intermediate value
and then do the put_user().
Additionally prefer the "+" constraint on pu_err and gu_err registers
to tell the compiler that those operands are both read and written by
the assembly instruction.
Reported-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 4b9d2a731c3d ("parisc: Switch user access functions to signal errors in r29 instead of r8")
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
It happens quite often that people use the wrong compiler to build the
kernel:
make ARCH=parisc -> builds the 32-bit kernel
make ARCH=parisc64 -> builds the 64-bit kernel
This patch adds a sanity check which errors out with an instruction how
use the correct ARCH= option.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.15+
|
|
Add the SO_TXREHASH socket option to control hash rethink behavior per socket.
When default mode is set, sockets disable rehash at initialization and use
sysctl option when entering listen state. setsockopt() overrides default
behavior.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The empty unmap_page_from_agp() macro causes a warning when
building with 'make W=1' on a couple of architectures:
drivers/char/agp/generic.c: In function 'agp_generic_destroy_page':
drivers/char/agp/generic.c:1265:28: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
1265 | unmap_page_from_agp(page);
Change the definitions to a 'do { } while (0)' construct to
make these more reliable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
|
|
Fix a missing prototype warning noticed by the kernel test robot.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
find_bit API and bitmap API are closely related, but inclusion paths
are different - include/asm-generic and include/linux, correspondingly.
In the past it made a lot of troubles due to circular dependencies
and/or undefined symbols. Fix this by moving find.h under include/linux.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
This patch fixes the following build error for source file
drivers/scsi/pcmcia/sym53c500_cs.c:
In file included from ./include/linux/bug.h:5,
from ./include/linux/cpumask.h:14,
from ./include/linux/mm_types_task.h:14,
from ./include/linux/mm_types.h:5,
from ./include/linux/buildid.h:5,
from ./include/linux/module.h:14,
from drivers/scsi/pcmcia/sym53c500_cs.c:42:
drivers/scsi/pcmcia/sym53c500_cs.c: In function ‘SYM53C500_intr’:
./arch/parisc/include/asm/bug.h:28:2: error: expected expression before ‘do’
28 | do { \
| ^~
./arch/parisc/include/asm/io.h:276:20: note: in expansion of macro ‘BUG’
276 | #define outb(x, y) BUG()
| ^~~
drivers/scsi/pcmcia/sym53c500_cs.c:124:19: note: in expansion of macro ‘outb’
124 | #define REG0(x) (outb(C4_IMG, (x) + CONFIG4))
| ^~~~
drivers/scsi/pcmcia/sym53c500_cs.c:362:2: note: in expansion of macro ‘REG0’
362 | REG0(port_base);
| ^~~~
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The definitions for pdc_toc_pim_11 and pdc_toc_pim_20 are wrong since they
include an entry for a hversion field which doesn't exist in the specification.
Fix this and clean up some whitespaces so that the whole file will be in
sync with it's copy in the SeaBIOS-hppa sources.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.16
|
|
The parisc architecture lacks general hardware support for compare and swap.
Particularly for userspace, it is difficult to implement software atomic
support. Page faults in critical regions can cause processes to sleep and
block the forward progress of other processes. Thus, it is essential that
page faults be disabled in critical regions. For performance reasons, we
also need to disable external interrupts in critical regions.
In order to do this, we need a mechanism to trigger COW breaks outside the
critical region. Fortunately, parisc has the "stbys,e" instruction. When
the leftmost byte of a word is addressed, this instruction triggers all
the exceptions of a normal store but it does not write to memory. Thus,
we can use it to trigger COW breaks outside the critical region without
modifying the data that is to be updated atomically.
COW breaks occur randomly. So even if we have priviously executed a "stbys,e"
instruction, we still need to disable pagefaults around the critical region.
If a fault occurs in the critical region, we return -EAGAIN. I had to add
a wrapper around _arch_futex_atomic_op_inuser() as I found in testing that
returning -EAGAIN caused problems for some processes even though it is
listed as a possible return value.
The patch implements the above. The code no longer attempts to sleep with
interrupts disabled and I haven't seen any stalls with the change.
I have attempted to merge common code and streamline the fast path. In the
futex code, we only compute the spinlock address once.
I eliminated some debug code in the original CAS routine that just made the
flow more complicated.
I don't clip the arguments when called from wide mode. As a result, the LWS
routines should work when called from 64-bit processes.
I defined TASK_PAGEFAULT_DISABLED offset for use in the lws_pagefault_disable
and lws_pagefault_enable macros.
Since we now disable interrupts on the gateway page where necessary, it
might be possible to allow processes to be scheduled when they are on the
gateway page.
Change has been tested on c8000 and rp3440. It improves glibc build and test
time by about 10%.
In v2, I removed the lws_atomic_xchg and and lws_atomic_store calls. I
also removed the bug fixes that were not directly related to this patch.
In v3, I removed the code to force interruptions from
arch_futex_atomic_op_inuser(). It is always called with page faults
disabled, so this code had no effect.
In v4, I fixed a typo in depi_safe line.
In v5, I moved the code to disable/enable page faults inside the spinlocks.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Use register r29 instead of register r8 to signal faults when accessing
user memory. In case of faults, the fixup routine will store -EFAULT in
this register.
This change saves up to 752 bytes on a 32bit kernel, partly because the
compiler doesn't need to save and restore the old r8 value on the stack.
bloat-o-meter results for usage with r29 register:
add/remove: 0/0 grow/shrink: 23/86 up/down: 228/-980 (-752)
bloat-o-meter results for usage with r28 register:
add/remove: 0/0 grow/shrink: 28/83 up/down: 296/-956 (-660)
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
While working on the rewrite to the light-weight syscall and futex code, I
experimented with using a hash index based on the user physical address of
atomic variable. This exposed two problems with the lpa and lpa_user defines.
Because of the copy instruction, the pa argument needs to be an early clobber
argument. This prevents gcc from allocating the va and pa arguments to the same
register.
Secondly, the lpa instruction can cause a page fault so we need to catch
exceptions.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 116d753308cf ("parisc: Use lpa instruction to load physical addresses in driver code")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.2+
|
|
The depi instruction is similar to the extru instruction on 64-bit machines.
It leaves the most-significant 32 bits of the target register in an undefined
state. On 64-bit machines, the macro uses depdi to perform safe deposits in
the least-significant 32 bits.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The address bits used to select the futex spinlock need to match those used in
the LWS code in syscall.S. The mask 0x3f8 only selects 7 bits. It should
select 8 bits.
This change fixes the glibc nptl/tst-cond24 and nptl/tst-cond25 tests.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Fixes: 53a42b6324b8 ("parisc: Switch to more fine grained lws locks")
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Pull folio fixes from Matthew Wilcox:
"In the course of preparing the folio changes for iomap for next merge
window, we discovered some problems that would be nice to address now:
- Renaming multi-page folios to large folios.
mapping_multi_page_folio_support() is just a little too long, so we
settled on mapping_large_folio_support(). That meant renaming, eg
folio_test_multi() to folio_test_large().
Rename AS_THP_SUPPORT to match
- I hadn't included folio wrappers for zero_user_segments(), etc.
Also, multi-page^W^W large folio support is now independent of
CONFIG_TRANSPARENT_HUGEPAGE, so machines with HIGHMEM always need
to fall back to the out-of-line zero_user_segments().
Remove FS_THP_SUPPORT to match
- The build bots finally got round to telling me that I missed a
couple of architectures when adding flush_dcache_folio(). Christoph
suggested that we just add linux/cacheflush.h and not rely on
asm-generic/cacheflush.h"
* tag 'folio-5.16b' of git://git.infradead.org/users/willy/pagecache:
mm: Add functions to zero portions of a folio
fs: Rename AS_THP_SUPPORT and mapping_thp_support
fs: Remove FS_THP_SUPPORT
mm: Remove folio_test_single
mm: Rename folio_test_multi to folio_test_large
Add linux/cacheflush.h
|
|
The extru instruction leaves the most significant 32 bits of the
target register in an undefined state on PA 2.0 systems.
Provide a macro to safely use extru on 32- and 64-bit machines.
Suggested-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This reverts commit e4f2006f1287e7ea17660490569cff323772dac4.
This patch shows problems with signal handling. Revert it for now.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v5.15
|
|
Building allmodconfig shows errors in the gpu/drm/msm snapdragon drivers,
because a COND() define is used there which conflicts with the COND() for
PA-RISC assembly. Although the snapdragon driver isn't relevant for parisc, it
is nevertheless compiled when CONFIG_COMPILE_TEST is defined.
Move the COND() define and other PA-RISC mnemonics inside the #ifdef
__ASSEMBLY__ part to avoid this conflict.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
|
|
Include stringify.h to avoid this build error:
arch/parisc/include/asm/jump_label.h: error: expected ':' before '__stringify'
arch/parisc/include/asm/jump_label.h: error: label 'l_yes' defined but not used [-Werror=unused-label]
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
|
