summaryrefslogtreecommitdiffstats
path: root/arch/mips/loongson64
AgeCommit message (Collapse)AuthorFilesLines
2020-03-25MIPS: Loongson64: Load built-in dtbsJiaxun Yang2-0/+39
Load proper dtb according to firmware passed parameters and CPU PRID. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Co-developed-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-03-25MIPS: Loongson64: Drop legacy IRQ codeJiaxun Yang4-180/+18
We've made generic irqchip drivers for Loongson-3 platform, it's time to say goodbye to these legacy code. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Co-developed-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-03-19MIPS: Loongson: Do not initialise statics to 0Tiezhu Yang1-1/+1
Fix the following checkpatch error: ERROR: do not initialise statics to 0 #125: FILE: loongson64/numa.c:125: + static unsigned long num_physpages = 0; Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-03-05MIPS: Replace setup_irq() by request_irq()afzal mohammed1-7/+3
request_irq() is preferred over setup_irq(). Invocations of setup_irq() occur after memory allocators are ready. Per tglx[1], setup_irq() existed in olden days when allocators were not ready by the time early interrupts were initialized. Hence replace setup_irq() by request_irq(). remove_irq() has been replaced by free_irq() as well. There were build error's during previous version, couple of which was reported by kbuild test robot <lkp@intel.com> of which one was reported by Thomas Bogendoerfer <tsbogend@alpha.franken.de> as well. There were a few more issues including build errors, those also have been fixed. [1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-01-31Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds2-1/+4
Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ...
2020-01-10MIPS: Loongson: Fix potential NULL dereference in loongson3_platform_init()Tiezhu Yang1-0/+3
If kzalloc fails, it should return -ENOMEM, otherwise may trigger a NULL pointer dereference. Fixes: 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org
2020-01-09MIPS: Loongson64: Fix node_distance()Thomas Bogendoerfer1-1/+1
Local node distance is defined as LOCAL_DISTANCE, which is 10. Use the define to give back correct local distance. Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org
2020-01-06remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig1-1/+1
ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
2019-11-11MIPS: Loongson64: Drop setup_pcimapJiaxun Yang1-43/+0
setup_pcimap is used to setup address windows for Loongson-3 built-in PCI-X controller, but this function is never been used in the real world and lack of support in kernel. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: chenhe@lemote.com
2019-11-11MIPS: Loongson{2ef, 32, 64} convert to generic fw cmdlineJiaxun Yang3-44/+3
All of Loongson firmwares are passing boot cmdline/env in the manner of YAMON/PMON. Thus we can remove duplicated cmdline initialize code and convert to generic fw method. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: chenhe@lemote.com
2019-11-11MIPS: Loongson: Unify LOONGSON3/LOONGSON64 Kconfig usageHuacai Chen1-1/+1
There are mixed LOONGSON3/LOONGSON64 usages in recently changes, let's establish some rules: 1, In Kconfig symbols, we only use CPU_LOONGSON64, MACH_LOONGSON64 and SYS_HAS_CPU_LOONGSON64, all other derived symbols use "LOONGSON3" since they all not widely-used symbols and sometimes not suitable for all 64-bit Loongson processors. E.g., we use symbols LOONGSON3_ENHANCEMENT, CPU_LOONGSON3_WORKAROUNDS, etc. 2, Hide GSx64/GSx64E in Kconfig title since it is not useful for general users. However, in the full description we use a more detailed manner. E.g., GS264/GS464/GS464E/GS464V. All Kconfig titles and descriptions of Loongson processors and machines have also been updated in this patch for consistency. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2019-11-01Merge tag 'mips_fixes_5.4_3' into mips-nextPaul Burton1-0/+4
Pull in mips-fixes primarily to gain build fixes in order to allow better testing of mips-next. A few MIPS fixes: - Fix VDSO time-related function behavior for systems where we need to fall back to syscalls, but were instead returning bogus results. - A fix to TLB exception handlers for Cavium Octeon systems where they would inadvertently clobber the $1/$at register. - A build fix for bcm63xx configurations. - Switch to using my @kernel.org email address. Signed-off-by: Paul Burton <paulburton@kernel.org>
2019-11-01MIPS: Loongson64: Move files to the top-level directoryJiaxun Yang22-72/+10
Current Loongson-3 code can share among all Loongson64 processors. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: chenhc@lemote.com Cc: paul.burton@mips.com
2019-11-01MIPS: Loongson64: Cleanup unused codeJiaxun Yang21-767/+26
Clean up legacy code after stripping out Loongson2ef code. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: paul.burton@mips.com
2019-11-01MIPS: Fork loongson2ef from loongson64Jiaxun Yang25-2415/+0
As later model of GSx64 family processors including 2-series-soc have similar design with initial loongson3a while loongson2e/f seems less identical, we separate loongson2e/f support code out of mach-loongson64 to make our life easier. This patch contains mostly file moving works. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> [paulburton@kernel.org: Squash in the MAINTAINERS updates] Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: paul.burton@mips.com
2019-10-31MIPS: Loongson64: Rename CPU TYPESJiaxun Yang4-9/+9
CPU_LOONGSON2 -> CPU_LOONGSON2EF CPU_LOONGSON3 -> CPU_LOONGSON64 As newer loongson-2 products (2G/2H/2K1000) can share kernel implementation with loongson-3 while 2E/2F are less similar with other LOONGSON64 products. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Cc: chenhc@lemote.com Cc: paul.burton@mips.com
2019-10-10MIPS: Disable Loongson MMI instructions for kernel buildPaul Burton1-0/+4
GCC 9.x automatically enables support for Loongson MMI instructions when using some -march= flags, and then errors out when -msoft-float is specified with: cc1: error: ‘-mloongson-mmi’ must be used with ‘-mhard-float’ The kernel shouldn't be using these MMI instructions anyway, just as it doesn't use floating point instructions. Explicitly disable them in order to fix the build with GCC 9.x. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 3702bba5eb4f ("MIPS: Loongson: Add GCC 4.4 support for Loongson2E") Fixes: 6f7a251a259e ("MIPS: Loongson: Add basic Loongson 2F support") Fixes: 5188129b8c9f ("MIPS: Loongson-3: Improve -march option and move it to Platform") Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: stable@vger.kernel.org # v2.6.32+ Cc: linux-mips@vger.kernel.org
2019-10-07MIPS: Loongson-3: Add CSR IPI supportHuacai Chen1-8/+62
CSR IPI and legacy MMIO use the same infrastructure, but CSR IPI is faster than legacy MMIO IPI. This patch enable CSR IPI if possible (except for MailBox, because CSR IPI is too complicated for MailBox). Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2019-10-07MIPS: Loongson: Add Loongson-3A R4 basic supportHuacai Chen1-39/+51
All Loongson-3 CPU family: Code-name Brand-name PRId Loongson-3A R1 Loongson-3A1000 0x6305 Loongson-3A R2 Loongson-3A2000 0x6308 Loongson-3A R2.1 Loongson-3A2000 0x630c Loongson-3A R3 Loongson-3A3000 0x6309 Loongson-3A R3.1 Loongson-3A3000 0x630d Loongson-3A R4 Loongson-3A4000 0xc000 Loongson-3B R1 Loongson-3B1000 0x6306 Loongson-3B R2 Loongson-3B1500 0x6307 Features of R4 revision of Loongson-3A: - All R2/R3 features, including SFB, V-Cache, FTLB, RIXI, DSP, etc. - Support variable ASID bits. - Support MSA and VZ extensions. - Support CPUCFG (CPU config) and CSR (Control and Status Register) extensions. - 64 entries of VTLB (classic TLB), 2048 entries of FTLB (8-way set-associative). Now 64-bit Loongson processors has three types of PRID.IMP: 0x6300 is the classic one so we call it PRID_IMP_LOONGSON_64C (e.g., Loongson-2E/ 2F/3A1000/3B1000/3B1500/3A2000/3A3000), 0x6100 is for some processors which has reduced capabilities so we call it PRID_IMP_LOONGSON_64R (e.g., Loongson-2K), 0xc000 is supposed to cover all new processors in general (e.g., Loongson-3A4000+) so we call it PRID_IMP_LOONGSON_64G. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2019-10-07MIPS: barrier: Remove loongson_llsc_mb()Paul Burton1-1/+1
The loongson_llsc_mb() macro is no longer used - instead barriers are emitted as part of inline asm using the __SYNC() macro. Remove the now-defunct loongson_llsc_mb() macro. Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: linux-kernel@vger.kernel.org
2019-10-02mips: Loongson: Fix the link time qualifier of 'serial_exit()'Christophe JAILLET1-1/+1
'exit' functions should be marked as __exit, not __init. Fixes: 85cc028817ef ("mips: make loongsoon serial driver explicitly modular") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: chenhc@lemote.com Cc: ralf@linux-mips.org Cc: jhogan@kernel.org Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: kernel-janitors@vger.kernel.org
2019-09-30MIPS: Loongson64: Fix boot failure after dropping boot_mem_mapHuacai Chen2-28/+18
From commit a94e4f24ec83 ("MIPS: init: Drop boot_mem_map") onwards, add_memory_region() is handled by memblock_add()/memblock_reserve() directly and all bootmem API should be converted to memblock API. Otherwise it will lead to boot failure, especially in the NUMA case because add_memory_region lose the node_id information. Fixes: a94e4f24ec836c8984f83959 ("MIPS: init: Drop boot_mem_map") Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> [paul.burton@mips.com: - Invert node_id check to de-indent the switch statement & avoid lines over 80 characters. - Fixup commit reference in commit message.] Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157Thomas Gleixner1-11/+1
Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner33-163/+33
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner5-0/+5
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-19Merge tag 'mips_fixes_5.1_1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS fixes from Paul Burton: "A small batch of MIPS fixes for 5.1: - An interrupt masking fix for Loongson-based Lemote 2F systems (fixing a regression from v3.19) - A relocation fix for configurations in which the devicetree is stored in an ELF section (fixing a regression from v4.7) - Fix jump labels for MIPSr6 kernels where they previously could inadvertently place a control transfer instruction in a forbidden slot & take unexpected exceptions (fixing MIPSr6 support added in v4.0) - Extend an existing USB power workaround for the Netgear WNDR3400 to v2 boards in addition to the v3 ones that already used it - Remove the custom MIPS32 definition of __kernel_fsid_t to make it consistent with MIPS64 & every other architecture, in particular resolving issues for code which tries to print the val field whose type previously differed (though had identical memory layout)" * tag 'mips_fixes_5.1_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: Remove custom MIPS32 __kernel_fsid_t type mips: bcm47xx: Enable USB power on Netgear WNDR3400v2 MIPS: Fix kernel crash for R6 in jump label branch function MIPS: Ensure ELF appended dtb is relocated mips: loongson64: lemote-2f: Add IRQF_NO_SUSPEND to "cascade" irqaction.
2019-03-11mips: loongson64: lemote-2f: Add IRQF_NO_SUSPEND to "cascade" irqaction.Yifeng Li1-1/+1
Timekeeping IRQs from CS5536 MFGPT are routed to i8259, which then triggers the "cascade" IRQ on MIPS CPU. Without IRQF_NO_SUSPEND in cascade_irqaction, MFGPT interrupts will be masked in suspend mode, and the machine would be unable to resume once suspended. Previously, MIPS IRQs were not disabled properly, so the original code appeared to work. Commit a3e6c1eff5 ("MIPS: IRQ: Fix disable_irq on CPU IRQs") uncovers the bug. To fix it, add IRQF_NO_SUSPEND to cascade_irqaction. This commit is functionally identical to 0add9c2f1cff ("MIPS: Loongson-3: Add IRQF_NO_SUSPEND to Cascade irqaction"), but it forgot to apply the same fix to Loongson2. Signed-off-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # v3.19+
2019-02-07mips: loongson64: remove unreachable(), fix loongson_poweroff().Yifeng Li1-1/+6
On my Yeeloong 8089, I noticed the machine fails to shutdown properly, and often, the function mach_prepare_reboot() is unexpectedly executed, thus the machine reboots instead. A wait loop is needed to ensure the system is in a well-defined state before going down. In commit 997e93d4df16 ("MIPS: Hang more efficiently on halt/powerdown/restart"), a general superset of the wait loop for all platforms is already provided, so we don't need to implement our own. This commit simply removes the unreachable() compiler marco after mach_prepare_reboot(), thus allowing the execution of machine_hang(). My test shows that the machine is now able to shutdown successfully. Please note that there are two different bugs preventing the machine from shutting down, another work-in-progress commit is needed to fix a lockup in cpufreq / i8259 driver, please read Reference, this commit does not fix that bug. Reference: https://lkml.org/lkml/2019/2/5/908 Signed-off-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Huacai Chen <chenhc@lemote.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-kernel@vger.kernel.org Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: stable@vger.kernel.org # v4.17+
2019-02-04MIPS: Loongson: Introduce and use loongson_llsc_mb()Huacai Chen1-0/+23
On the Loongson-2G/2H/3A/3B there is a hardware flaw that ll/sc and lld/scd is very weak ordering. We should add sync instructions "before each ll/lld" and "at the branch-target between ll/sc" to workaround. Otherwise, this flaw will cause deadlock occasionally (e.g. when doing heavy load test with LTP). Below is the explaination of CPU designer: "For Loongson 3 family, when a memory access instruction (load, store, or prefetch)'s executing occurs between the execution of LL and SC, the success or failure of SC is not predictable. Although programmer would not insert memory access instructions between LL and SC, the memory instructions before LL in program-order, may dynamically executed between the execution of LL/SC, so a memory fence (SYNC) is needed before LL/LLD to avoid this situation. Since Loongson-3A R2 (3A2000), we have improved our hardware design to handle this case. But we later deduce a rarely circumstance that some speculatively executed memory instructions due to branch misprediction between LL/SC still fall into the above case, so a memory fence (SYNC) at branch-target (if its target is not between LL/SC) is needed for Loongson 3A1000, 3B1500, 3A2000 and 3A3000. Our processor is continually evolving and we aim to to remove all these workaround-SYNCs around LL/SC for new-come processor." Here is an example: Both cpu1 and cpu2 simutaneously run atomic_add by 1 on same atomic var, this bug cause both 'sc' run by two cpus (in atomic_add) succeed at same time('sc' return 1), and the variable is only *added by 1*, sometimes, which is wrong and unacceptable(it should be added by 2). Why disable fix-loongson3-llsc in compiler? Because compiler fix will cause problems in kernel's __ex_table section. This patch fix all the cases in kernel, but: +. the fix at the end of futex_atomic_cmpxchg_inatomic is for branch-target of 'bne', there other cases which smp_mb__before_llsc() and smp_llsc_mb() fix the ll and branch-target coincidently such as atomic_sub_if_positive/ cmpxchg/xchg, just like this one. +. Loongson 3 does support CONFIG_EDAC_ATOMIC_SCRUB, so no need to touch edac.h +. local_ops and cmpxchg_local should not be affected by this bug since only the owner can write. +. mips_atomic_set for syscall.c is deprecated and rarely used, just let it go Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Huang Pei <huangpei@loongson.cn> [paul.burton@mips.com: - Simplify the addition of -mno-fix-loongson3-llsc to cflags, and add a comment describing why it's there. - Make loongson_llsc_mb() a no-op when CONFIG_CPU_LOONGSON3_WORKAROUNDS=n, rather than a compiler memory barrier. - Add a comment describing the bug & how loongson_llsc_mb() helps in asm/barrier.h.] Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: ambrosehua@gmail.com Cc: Steven J . Hill <Steven.Hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Li Xuefeng <lixuefeng@loongson.cn> Cc: Xu Chenghua <xuchenghua@loongson.cn>
2018-12-29Merge tag 'kconfig-v4.21-2' of ↵Linus Torvalds1-4/+3
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kconfig file consolidation from Masahiro Yamada: "Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by Christoph Hellwig. Currently, every architecture that wants to provide common peripheral busses needs to add some boilerplate code and include the right Kconfig files. This series instead just selects the presence (when needed) and then handles everything in the bus-specific Kconfig file under drivers/" * tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: pcmcia: remove per-arch PCMCIA config entry eisa: consolidate EISA Kconfig entry in drivers/eisa rapidio: consolidate RAPIDIO config entry in drivers/rapidio pcmcia: allow PCMCIA support independent of the architecture PCI: consolidate the PCI_SYSCALL symbol PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options PCI: consolidate PCI config entry in drivers/pci MIPS: remove the HT_PCI config option
2018-12-26Merge tag 'mips_4.21' of ↵Linus Torvalds3-7/+6
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Paul Burton: "Here's the main MIPS pull for Linux 4.21. Core architecture changes include: - Syscall tables & definitions for unistd.h are now generated by scripts, providing greater consistency with other architectures & making it easier to add new syscalls. - Support for building kernels with no floating point support, upon which any userland attempting to use floating point instructions will receive a SIGILL. Mostly useful to shrink the kernel & as preparation for nanoMIPS support which does not yet include FP. - MIPS SIMD Architecture (MSA) vector register context is now exposed by ptrace via a new NT_MIPS_MSA regset. - ASIDs are now stored as 64b values even for MIPS32 kernels, expanding the ASID version field sufficiently that we don't need to worry about overflow & avoiding rare issues with reused ASIDs that have been observed in the wild. - The branch delay slot "emulation" page is now mapped without write permission for the user, preventing its use as a nice location for attacks to execute malicious code from. - Support for ioremap_prot(), primarily to allow gdb or other ptrace users the ability to view their tracee's memory using the same cache coherency attribute. - Optimizations to more cpu_has_* macros, allowing more to be compile-time constant where possible. - Enable building the whole kernel with UBSAN instrumentation. - Enable building the kernel with link-time dead code & data elimination. Platform specific changes include: - The Boston board gains a workaround for DMA prefetching issues with the EG20T Platform Controller Hub that it uses. - Cleanups to Cavium Octeon code removing about 20k lines of redundant code, mostly unused or duplicate register definitions in headers. - defconfig updates for the DECstation machines, including new defconfigs for r4k & 64b machines. - Further work on Loongson 3 support. - DMA fixes for SiByte machines" * tag 'mips_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (95 commits) MIPS: math-emu: Write-protect delay slot emulation pages MIPS: Remove struct mm_context_t fp_mode_switching field mips: generate uapi header and system call table files mips: add system call table generation support mips: remove syscall table entries mips: add +1 to __NR_syscalls in uapi header mips: rename scall64-64.S to scall64-n64.S mips: remove unused macros mips: add __NR_syscalls along with __NR_Linux_syscalls MIPS: Expand MIPS32 ASIDs to 64 bits MIPS: OCTEON: delete redundant register definitions MIPS: OCTEON: cvmx_gmxx_inf_mode: use oldest forward compatible definition MIPS: OCTEON: cvmx_mio_fus_dat3: use oldest forward compatible definition MIPS: OCTEON: cvmx_pko_mem_debug8: use oldest forward compatible definition MIPS: OCTEON: octeon-usb: use common gpio_bit definition MIPS: OCTEON: enable all OCTEON drivers in defconfig mips: annotate implicit fall throughs MIPS: Hardcode cpu_has_mips* where target ISA allows MIPS: MT: Remove norps command line parameter MIPS: Only include mmzone.h when CONFIG_NEED_MULTIPLE_NODES=y ...
2018-11-23PCI: consolidate PCI config entry in drivers/pciChristoph Hellwig1-4/+3
There is no good reason to duplicate the PCI menu in every architecture. Instead provide a selectable HAVE_PCI symbol that indicates availability of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the rest in drivers/pci. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Palmer Dabbelt <palmer@sifive.com> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-23MIPS: remove the HT_PCI config optionChristoph Hellwig1-1/+1
This option is always selected from LOONGSON_MACH3X. Switch to just seleting PCI from that option and definining LOONGSON_PCIIO_BASE based on CONFIG_LOONGSON_MACH3X. PCI already selects PCI_DOMAINS. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-19MIPS: Loongson: Add Loongson-3A R2.1 basic supportHuacai Chen2-2/+4
Loongson-3A R2.1 is the bugfix revision of Loongson-3A R2. All Loongson-3 CPU family: Code-name Brand-name PRId Loongson-3A R1 Loongson-3A1000 0x6305 Loongson-3A R2 Loongson-3A2000 0x6308 Loongson-3A R2.1 Loongson-3A2000 0x630c Loongson-3A R3 Loongson-3A3000 0x6309 Loongson-3A R3.1 Loongson-3A3000 0x630d Loongson-3B R1 Loongson-3B1000 0x6306 Loongson-3B R2 Loongson-3B1500 0x6307 Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/21128/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <james.hogan@mips.com> Cc: Steven J . Hill <Steven.Hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com>
2018-11-15MIPS: Loongson3,SGI-IP27: Simplify max_low_pfn calculationPaul Burton1-10/+2
Both the Loongson3 & SGI-IP27 platforms set max_low_pfn to the last available PFN describing memory. They both do it in paging_init() which is later than ideal since max_low_pfn is used before that function is called. Simplify both platforms to trivially initialize max_low_pfn using the end address of DRAM, and do it earlier in prom_meminit(). Signed-off-by: Paul Burton <paul.burton@mips.com> Suggested-by: Mike Rapoport <rppt@linux.ibm.com> Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Patchwork: https://patchwork.linux-mips.org/patch/21104/ References: https://patchwork.linux-mips.org/patch/21031/ Cc: Huacai Chen <chenhc@lemote.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de> Cc: linux-mips@linux-mips.org
2018-11-09MIPS: Simplify FP context initializationPaul Burton1-5/+2
MIPS has up until now had 3 different ways for a task's floating point context to be initialized: - If the task's first use of FP involves it gaining ownership of an FPU then _init_fpu() is used to initialize the FPU's registers such that they all contain ~0, and the FPU registers will be stored to struct thread_info later (eg. when context switching). - If the task first uses FP on a CPU without an associated FPU then fpu_emulator_init_fpu() initializes the task's floating point register state in struct thread_info such that all floating point register contain the bit pattern 0x7ff800007ff80000, different to the _init_fpu() behaviour. - If a task's floating point context is first accessed via ptrace then init_fp_ctx() initializes the floating point register state in struct thread_info to ~0, giving equivalent state to _init_fpu(). The _init_fpu() path has 2 separate implementations - one for r2k/r3k style systems & one for r4k style systems. The _init_fpu() path also requires that we be careful to clear & restore the value of the Config5.FRE bit on modern systems in order to avoid inadvertently triggering floating point exceptions. None of this code is in a performance critical hot path - it runs only the first time a task uses floating point. As such it doesn't seem to warrant the complications of maintaining the _init_fpu() path. Remove _init_fpu() & fpu_emulator_init_fpu(), instead using init_fp_ctx() consistently to initialize floating point register state in struct thread_info. Upon a task's first use of floating point this will typically mean that we initialize state in memory & then load it into FPU registers using _restore_fp() just as we would on a context switch. For other paths such as __compute_return_epc_for_insn() or mipsr2_decoder() this results in a significant simplification of the work to be done. Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/21002/ Cc: linux-mips@linux-mips.org
2018-10-31mm: remove include/linux/bootmem.hMike Rapoport2-2/+1
Move remaining definitions and declarations from include/linux/bootmem.h into include/linux/memblock.h and remove the redundant header. The includes were replaced with the semantic patch below and then semi-automated removal of duplicated '#include <linux/memblock.h> @@ @@ - #include <linux/bootmem.h> + #include <linux/memblock.h> [sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h] Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au [sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h] Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au [sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal] Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Jonas Bonn <jonas@southpole.se> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ley Foon Tan <lftan@altera.com> Cc: Mark Salter <msalter@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Matt Turner <mattst88@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31memblock: rename free_all_bootmem to memblock_free_allMike Rapoport1-1/+1
The conversion is done using sed -i 's@free_all_bootmem@memblock_free_all@' \ $(git grep -l free_all_bootmem) Link: http://lkml.kernel.org/r/1536927045-23536-26-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Greentime Hu <green.hu@gmail.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Jonas Bonn <jonas@southpole.se> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ley Foon Tan <lftan@altera.com> Cc: Mark Salter <msalter@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Matt Turner <mattst88@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Simek <monstr@monstr.eu> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Richard Weinberger <richard@nod.at> Cc: Rich Felker <dalias@libc.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-15MIPS: Loongson-3: Fix BRIDGE irq delivery problemHuacai Chen1-10/+3
After commit e509bd7da149dc349160 ("genirq: Allow migration of chained interrupts by installing default action") Loongson-3 fails at here: setup_irq(LOONGSON_HT1_IRQ, &cascade_irqaction); This is because both chained_action and cascade_irqaction don't have IRQF_SHARED flag. This will cause Loongson-3 resume fails because HPET timer interrupt can't be delivered during S3. So we set the irqchip of the chained irq to loongson_irq_chip which doesn't disable the chained irq in CP0.Status. Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20434/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2018-10-15MIPS: Loongson-3: Fix CPU UART irq delivery problemHuacai Chen1-40/+3
Masking/unmasking the CPU UART irq in CP0_Status (and redirecting it to other CPUs) may cause interrupts be lost, especially in multi-package machines (Package-0's UART irq cannot be delivered to others). So make mask_loongson_irq() and unmask_loongson_irq() be no-ops. The original problem (UART IRQ may deliver to any core) is also because of masking/unmasking the CPU UART irq in CP0_Status. So it is safe to remove all of the stuff. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20433/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2018-09-22MIPS: kexec: Make a framework for both jumping and halting on nonboot CPUsDengcheng Zhu1-0/+4
The existing implementation lets machine_kexec() CPU jump to reboot code buffer, whereas other CPUs to relocated_kexec_smp_wait. The natural way to bring up an SMP new kernel would be to let CPU0 do it while others being halted. For those failing to do so, fall back to the jumping method. Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com> [paul.burton@mips.com: Guard kexec_nonboot_cpu_jump with CONFIG_SMP] Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20570/ Cc: pburton@wavecomp.com Cc: ralf@linux-mips.org Cc: linux-mips@linux-mips.org Cc: rachel.mozes@intel.com
2018-09-14mips: switch to NO_BOOTMEMMike Rapoport1-19/+15
MIPS already has memblock support and all the memory is already registered with it. This patch replaces bootmem memory reservations with memblock ones and removes the bootmem initialization. Since memblock allocates memory in top-down mode, we ensure that memblock limit is max_low_pfn to prevent allocations from the high memory. To have the exceptions base in the lower 512M of the physical memory, its allocation in arch/mips/kernel/traps.c::traps_init() is using bottom-up mode. Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20560/ Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: linux-mips@linux-mips.org Cc: linux-mm@kvack.org Cc: linux-kernel@vger.kernel.org
2018-08-31MIPS: Remove no-op/identity castsPaul Burton1-5/+5
Clean up instances of casts to the type that a value already has, since they are effectively no-ops and only serve to complicate the code. This is the result of the following semantic patch: @identitycast@ type T; T *A; @@ - (T *)(A) + A Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19599/
2018-08-28MIPS: Loongon64: DMA functions cleanupHuacai Chen5-7/+14
Split the common dma.c which shared by Loongson-2E and Loongson-2F, since the code in 'common' directory is assumed be shared by all 64bit Loongson platforms (but Loongson-3 doesn't use it now). By the way, Loongson-2E and Loongson-2F have already dropped 32bit kernel support, so CONFIG_64BIT isn't needed. Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/20302/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2018-07-23MIPS: Loongson: Add Loongson-3A R3.1 basic supportHuacai Chen2-2/+4
Loongson-3A R3.1 is the bugfix revision of Loongson-3A R3. All Loongson-3 CPU family: Code-name Brand-name PRId Loongson-3A R1 Loongson-3A1000 0x6305 Loongson-3A R2 Loongson-3A2000 0x6308 Loongson-3A R3 Loongson-3A3000 0x6309 Loongson-3A R3.1 Loongson-3A3000 0x630d Loongson-3B R1 Loongson-3B1000 0x6306 Loongson-3B R2 Loongson-3B1500 0x6307 Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19263/ Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <james.hogan@mips.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Huacai Chen <chenhuacai@gmail.com>
2018-07-17MIPS: loongson64: cs5536: Fix PCI_OHCI_INT_REG readsPaul Burton1-1/+1
The PCI_OHCI_INT_REG case in pci_ohci_read_reg() contains the following if statement: if ((lo & 0x00000f00) == CS5536_USB_INTR) CS5536_USB_INTR expands to the constant 11, which gives us the following condition which can never evaluate true: if ((lo & 0xf00) == 11) At least when using GCC 8.1.0 this falls foul of the tautoligcal-compare warning, and since the code is built with the -Werror flag the build fails. Fix this by shifting lo right by 8 bits in order to match the corresponding PCI_OHCI_INT_REG case in pci_ohci_write_reg(). Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19861/ Cc: Huacai Chen <chenhc@lemote.com> Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
2018-07-17mips: unify prom_putchar() declarationsAlexander Sverdlin1-0/+1
prom_putchar() is used centrally in early printk infrastructure therefore at least MIPS should agree on the function return type. [paul.burton@mips.com: - Include linux/types.h in asm/setup.h to gain the bool typedef before we start include asm/setup.h elsewhere. - Include asm/setup.h in all files that use or define prom_putchar(). - Also standardise on signed rather than unsigned char argument.] Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Patchwork: https://patchwork.linux-mips.org/patch/19842/ Cc: linux-mips@linux-mips.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Jonas Gorski <jonas.gorski@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com>
2018-06-24MIPS: loongson64: use generic dma noncoherent opsChristoph Hellwig3-2/+19
Provide phys_to_dma/dma_to_phys helpers, everything else is generic. Signed-off-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/19545/ Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: David Daney <david.daney@cavium.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de> Cc: Huacai Chen <chenhc@lemote.com> Cc: iommu@lists.linux-foundation.org Cc: linux-mips@linux-mips.org
2018-06-24MIPS: loongson: untangle dma implementationsChristoph Hellwig4-23/+5
Only loongson-3 is DMA coherent and uses swiotlb. So move the dma address translations stubs directly to the loongson-3 code, and remove a few Kconfig indirections. Signed-off-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/19539/ Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: David Daney <david.daney@cavium.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de> Cc: Huacai Chen <chenhc@lemote.com> Cc: iommu@lists.linux-foundation.org Cc: linux-mips@linux-mips.org
2018-06-24MIPS: make the default mips dma implementation optionalChristoph Hellwig1-0/+2
Octeon and loonson64 already don't use it at all, and we're going to migrate more plaforms away from it. Signed-off-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/19536/ Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: David Daney <david.daney@cavium.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de> Cc: Huacai Chen <chenhc@lemote.com> Cc: iommu@lists.linux-foundation.org Cc: linux-mips@linux-mips.org
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 01:36:14 +0000