| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM fixes from Russell King:
"This round of fixes is smaller than previous: a couple more updates
for the security fixes, and a one-liner kexec fix"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7816/1: CONFIG_KUSER_HELPERS: fix help text
ARM: 7815/1: kexec: offline non panic CPUs on Kdump panic
ARM: 7819/1: fiq: Cast the first argument of flush_icache_range()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes for 3.11 are still trickling in. These are:
- A couple of fixes for older OMAP platforms
- Another few fixes for at91 (lateish due to European summer
vacations)
- A late-found problem with USB on Tegra, fix is to keep VBUS
regulator on at all times
- One fix for Exynos 5440 dealing with CPU detection
- One MAINTAINERS update"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: always enable USB VBUS regulators
ARM: davinci: nand: specify ecc strength
ARM: OMAP: rx51: change musb mode to OTG
ARM: OMAP2: fix musb usage for n8x0
MAINTAINERS: Update email address for Benoit Cousson
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: SAMSUNG: fix to support for missing cpu specific map_io
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
|
|
This fixes a regression exposed during the merge window by commit
9f310de "ARM: tegra: fix VBUS regulator GPIO polarity in DT"; namely that
USB VBUS doesn't get turned on, so USB devices are not detected. This
affects the internal USB port on TrimSlice (i.e. the USB->SATA bridge, to
which the SSD is connected) and the external port(s) on Seaboard/
Springbank and Whistler.
The Tegra DT as written in v3.11 allows two paths to enable USB VBUS:
1) Via the legacy DT binding for the USB controller; it can directly
acquire a VBUS GPIO and activate it.
2) Via a regulator for VBUS, which is referenced by the new DT binding
for the USB controller.
Those two methods both use the same GPIO, and hence whichever of the
USB controller and regulator gets probed first ends up owning the GPIO.
In practice, the USB driver only supports path (1) above, since the
patches to support the new USB binding are not present until v3.12:-(
In practice, the regulator ends up being probed first and owning the
GPIO. Since nothing enables the regulator (the USB driver code is not
yet present), the regulator ends up being turned off. This originally
caused no problem, because the polarity in the regulator definition was
incorrect, so attempting to turn off the regulator actually turned it
on, and everything worked:-(
However, when testing the new USB driver code in v3.12, I noticed the
incorrect polarity and fixed it in commit 9f310de "ARM: tegra: fix VBUS
regulator GPIO polarity in DT". In the context of v3.11, this patch then
caused the USB VBUS to actually turn off, which broke USB ports with VBUS
control. I got this patch included in v3.11-rc1 since it fixed a bug in
device tree (incorrect polarity specification), and hence was suitable to
be included early in the rc series. I evidently did not test the patch at
all, or correctly, in the context of v3.11, and hence did not notice the
issue that I have explained above:-(
Fix this by making the USB VBUS regulators always enabled. This way, if
the regulator owns the GPIO, it will always be turned on, even if there
is no USB driver code to request the regulator be turned on. Even
ignoring this bug, this is a reasonable way to configure the HW anyway.
If this patch is applied to v3.11, it will cause a couple pretty trivial
conflicts in tegra20-{trimslice,seaboard}.dts when creating v3.12, since
the context right above the added lines changed in patches destined for
v3.12.
Reported-by: Kyle McMartin <kmcmarti@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- On ARM did not have balanced calls to get/put_cpu.
- Fix to make tboot + Xen + Linux correctly.
- Fix events VCPU binding issues.
- Fix a vCPU online race where IPIs are sent to not-yet-online vCPU.
* tag 'stable/for-linus-3.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/smp: initialize IPI vectors before marking CPU online
xen/events: mask events when changing their VCPU binding
xen/events: initialize local per-cpu mask for all possible events
x86/xen: do not identity map UNUSABLE regions in the machine E820
xen/arm: missing put_cpu in xen_percpu_init
|
|
Pull kvm fixes from Paolo Bonzini:
"Fixes for ARM and aarch64.
This pull request is coming a bit later than I would have preferred,
because I and Gleb happened to have holidays around the same weeks of
August... sorry about that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: ARM: Squash len warning
arm64: KVM: use 'int' instead of 'u32' for variable 'target' in kvm_host.h.
arm64: KVM: add missing dsb before invalidating Stage-2 TLBs
arm64: KVM: perform save/restore of PAR_EL1
arm64: KVM: fix 2-level page tables unmapping
ARM: KVM: Fix unaligned unmap_range leak
ARM: KVM: Fix 64-bit coprocessor handling
|
|
|
|
Commit f6f91b0d9fd9 ("ARM: allow kuser helpers to be removed from the
vector page") introduced some help text for the CONFIG_KUSER_HELPERS
option which is rather contradictory.
Let's fix that, and improve it a little.
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In case of normal kexec kernel load, all cpu's are offlined
before calling machine_kexec().But in case crash panic cpus
are relaxed in machine_crash_nonpanic_core() SMP function
but not offlined.
When crash kernel is loaded with kexec and on panic trigger
machine_kexec() checks for number of cpus online.
If more than one cpu is online machine_kexec() fails to load
with below error
kexec: error: multiple CPUs still online
In machine_crash_nonpanic_core() SMP function, offline CPU
before cpu_relax
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 2ba85e7af4 (ARM: Fix FIQ code on VIVT CPUs) causes the following build warning:
arch/arm/kernel/fiq.c:92:3: warning: passing argument 1 of 'cpu_cache.coherent_kern_range' makes integer from pointer without a cast [enabled by default]
Cast it as '(unsigned long)base' to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Starting with kernel v3.5, it is mandatory
to specify ECC strength when using hardware
ECC. Without this, kernel panics with a warning
of the sort:
Driver must set ecc.strength when using hardware ECC
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:3519!
Fix this by specifying ECC strength for the boards
which were missing this.
Reported-by: Holger Freyther <holger@freyther.de>
Cc: <stable@vger.kernel.org> #v3.5+
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Pull ARM fixes from Russell King:
"The usual collection of random fixes. Also some further fixes to the
last set of security fixes, and some more from Will (which you may
already have in a slightly different form)"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7807/1: kexec: validate CPU hotplug support
ARM: 7812/1: rwlocks: retry trylock operation if strex fails on free lock
ARM: 7811/1: locks: use early clobber in arch_spin_trylock
ARM: 7810/1: perf: Fix array out of bounds access in armpmu_map_hw_event()
ARM: 7809/1: perf: fix event validation for software group leaders
ARM: Fix FIQ code on VIVT CPUs
ARM: Fix !kuser helpers case
ARM: Fix the world famous typo with is_gate_vma()
|
|
Peripheral-only mode got broken in v3.11-rc1 because of unknown reasons.
Change the mode to OTG, in practice that should work equally well even
when/if the regression gets fixed.
Note that the peripheral-only regression is a separate patch, this change
is still correct as the role is handled by hardware.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit b7e2e75a8c ("usb: gadget: drop unused USB_GADGET_MUSB_HDRC")
dropped a config symbol that was unused by the musb core, but it turns
out that board support code still had references to it.
As the core now handles both dual role and host-only modes, we can just
pass MUSB_OTG as mode from board files.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Ben Tebulin reported:
"Since v3.7.2 on two independent machines a very specific Git
repository fails in 9/10 cases on git-fsck due to an SHA1/memory
failures. This only occurs on a very specific repository and can be
reproduced stably on two independent laptops. Git mailing list ran
out of ideas and for me this looks like some very exotic kernel issue"
and bisected the failure to the backport of commit 53a59fc67f97 ("mm:
limit mmu_gather batching to fix soft lockups on !CONFIG_PREEMPT").
That commit itself is not actually buggy, but what it does is to make it
much more likely to hit the partial TLB invalidation case, since it
introduces a new case in tlb_next_batch() that previously only ever
happened when running out of memory.
The real bug is that the TLB gather virtual memory range setup is subtly
buggered. It was introduced in commit 597e1c3580b7 ("mm/mmu_gather:
enable tlb flush range in generic mmu_gather"), and the range handling
was already fixed at least once in commit e6c495a96ce0 ("mm: fix the TLB
range flushed when __tlb_remove_page() runs out of slots"), but that fix
was not complete.
The problem with the TLB gather virtual address range is that it isn't
set up by the initial tlb_gather_mmu() initialization (which didn't get
the TLB range information), but it is set up ad-hoc later by the
functions that actually flush the TLB. And so any such case that forgot
to update the TLB range entries would potentially miss TLB invalidates.
Rather than try to figure out exactly which particular ad-hoc range
setup was missing (I personally suspect it's the hugetlb case in
zap_huge_pmd(), which didn't have the same logic as zap_pte_range()
did), this patch just gets rid of the problem at the source: make the
TLB range information available to tlb_gather_mmu(), and initialize it
when initializing all the other tlb gather fields.
This makes the patch larger, but conceptually much simpler. And the end
result is much more understandable; even if you want to play games with
partial ranges when invalidating the TLB contents in chunks, now the
range information is always there, and anybody who doesn't want to
bother with it won't introduce subtle bugs.
Ben verified that this fixes his problem.
Reported-bisected-and-tested-by: Ben Tebulin <tebulin@googlemail.com>
Build-testing-by: Stephen Rothwell <sfr@canb.auug.org.au>
Build-testing-by: Richard Weinberger <richard.weinberger@gmail.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
From Nicolas Ferre:
Device tree related fixes:
- USB host numbering for 9x5 which was preventing from using all ports
- a missing UART (not USART) clock lookup table was preventing from using
them on 9x5
- too large amount of memory was specified for 9n12ek
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.5+
|
|
Add clocks to clock lookup table for uart DT entries.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fix constraint check in armpmu_map_hw_event().
Reported-and-tested-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Architectures should fully validate whether kexec is possible as part of
machine_kexec_prepare(), so that user-space's kexec_load() operation can
report any problems. Performing validation in machine_kexec() itself is
too late, since it is not allowed to return.
Prior to this patch, ARM's machine_kexec() was testing after-the-fact
whether machine_kexec_prepare() was able to disable all but one CPU.
Instead, modify machine_kexec_prepare() to validate all conditions
necessary for machine_kexec_prepare()'s to succeed. BUG if the validation
succeeded, yet disabling the CPUs didn't actually work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 15e7e5c1ebf5 ("ARM: 7749/1: spinlock: retry trylock operation if
strex fails on free lock") modifying our arch_spin_trylock to retry the
acquisition if the lock appeared uncontended, but the strex failed.
This patch does the same for rwlocks, which were missed by the original
patch.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The res variable is written before we've finished with the input
operands (namely the lock address), so ensure that we mark it as `early
clobber' to avoid unintended register sharing.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Vince Weaver reports an oops in the ARM perf event code while
running his perf_fuzzer tool on a pandaboard running v3.11-rc4.
Unable to handle kernel paging request at virtual address 73fd14cc
pgd = eca6c000
[73fd14cc] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: snd_soc_omap_hdmi omapdss snd_soc_omap_abe_twl6040 snd_soc_twl6040 snd_soc_omap snd_soc_omap_hdmi_card snd_soc_omap_mcpdm snd_soc_omap_mcbsp snd_soc_core snd_compress regmap_spi snd_pcm snd_page_alloc snd_timer snd soundcore
CPU: 1 PID: 2790 Comm: perf_fuzzer Not tainted 3.11.0-rc4 #6
task: eddcab80 ti: ed892000 task.ti: ed892000
PC is at armpmu_map_event+0x20/0x88
LR is at armpmu_event_init+0x38/0x280
pc : [<c001c3e4>] lr : [<c001c17c>] psr: 60000013
sp : ed893e40 ip : ecececec fp : edfaec00
r10: 00000000 r9 : 00000000 r8 : ed8c3ac0
r7 : ed8c3b5c r6 : edfaec00 r5 : 00000000 r4 : 00000000
r3 : 000000ff r2 : c0496144 r1 : c049611c r0 : edfaec00
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: aca6c04a DAC: 00000015
Process perf_fuzzer (pid: 2790, stack limit = 0xed892240)
Stack: (0xed893e40 to 0xed894000)
3e40: 00000800 c001c17c 00000002 c008a748 00000001 00000000 00000000 c00bf078
3e60: 00000000 edfaee50 00000000 00000000 00000000 edfaec00 ed8c3ac0 edfaec00
3e80: 00000000 c073ffac ed893f20 c00bf180 00000001 00000000 c00bf078 ed893f20
3ea0: 00000000 ed8c3ac0 00000000 00000000 00000000 c0cb0818 eddcab80 c00bf440
3ec0: ed893f20 00000000 eddcab80 eca76800 00000000 eca76800 00000000 00000000
3ee0: 00000000 ec984c80 eddcab80 c00bfe68 00000000 00000000 00000000 00000080
3f00: 00000000 ed892000 00000000 ed892030 00000004 ecc7e3c8 ecc7e3c8 00000000
3f20: 00000000 00000048 ecececec 00000000 00000000 00000000 00000000 00000000
3f40: 00000000 00000000 00297810 00000000 00000000 00000000 00000000 00000000
3f60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3f80: 00000002 00000002 000103a4 00000002 0000016c c00128e8 ed892000 00000000
3fa0: 00090998 c0012700 00000002 000103a4 00090ab8 00000000 00000000 0000000f
3fc0: 00000002 000103a4 00000002 0000016c 00090ab0 00090ab8 000107a0 00090998
3fe0: bed92be0 bed92bd0 0000b785 b6e8f6d0 40000010 00090ab8 00000000 00000000
[<c001c3e4>] (armpmu_map_event+0x20/0x88) from [<c001c17c>] (armpmu_event_init+0x38/0x280)
[<c001c17c>] (armpmu_event_init+0x38/0x280) from [<c00bf180>] (perf_init_event+0x108/0x180)
[<c00bf180>] (perf_init_event+0x108/0x180) from [<c00bf440>] (perf_event_alloc+0x248/0x40c)
[<c00bf440>] (perf_event_alloc+0x248/0x40c) from [<c00bfe68>] (SyS_perf_event_open+0x4f4/0x8fc)
[<c00bfe68>] (SyS_perf_event_open+0x4f4/0x8fc) from [<c0012700>] (ret_fast_syscall+0x0/0x48)
Code: 0a000005 e3540004 0a000016 e3540000 (0791010c)
This is because event->attr.config in armpmu_event_init()
contains a very large number copied directly from userspace and
is never checked against the size of the array indexed in
armpmu_map_hw_event(). Fix the problem by checking the value of
config before indexing the array and rejecting invalid config
values.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It is possible to construct an event group with a software event as a
group leader and then subsequently add a hardware event to the group.
This results in the event group being validated by adding all members
of the group to a fake PMU and attempting to allocate each event on
their respective PMU.
Unfortunately, for software events wthout a corresponding arm_pmu, this
results in a kernel crash attempting to dereference the ->get_event_idx
function pointer.
This patch fixes the problem by checking explicitly for software events
and ignoring those in event validation (since they can always be
scheduled). We will probably want to revisit this for 3.12, since the
validation checks don't appear to work correctly when dealing with
multiple hardware PMUs anyway.
Cc: <stable@vger.kernel.org>
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.linaro.org/people/cdall/linux-kvm-arm into kvm-master
KVM/ARM Fixes for the Linux 3.11 release
|
|
The 'len' variable was declared an unsigned and then checked for less
than 0, which results in warnings on some compilers. Since len is
assigned an int, make it an int.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Fix to boot kernel on exynos5440 which has no specific map_io(). Current kernel
cannot support no CPU specific map_io() for Samsung SoCs.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: fix to support for missing cpu specific map_io
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
- MSM: GPIO fixes (includes old code removal)
- OMAP: earlyprintk regression, AM33xx cpgmac PM regression
- OMAP5: urgent fix for potentially harmful voltage regulator values
- Renesas: gpio-keys fix, fix SD card detection, fix shdma calculation
error
- STi: critical SMP boot fix
- tegra: DTS fix for usb-phy
- a couple MAINTAINERS updates
(Arnd is on paternity leave, Kevin is stepping up to help arm-soc
maintenance)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: add TI Keystone ARM platform
MAINTAINERS: delete Srinidhi from ux500
ARM: tegra: enable ULPI phy on Colibri T20
ARM: STi: remove sti_secondary_start from INIT section.
ARM: STi: Fix cpu nodes with correct device_type.
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
ARM: msm: Consolidate gpiomux for older architectures
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
ARM: msm: dts: Fix the gpio register address for msm8960
|
|
Aaro Koskinen reports the following oops:
Installing fiq handler from c001b110, length 0x164
Unable to handle kernel paging request at virtual address ffff1224
pgd = c0004000
[ffff1224] *pgd=00000000, *pte=11fff0cb, *ppte=11fff00a
...
[<c0013154>] (set_fiq_handler+0x0/0x6c) from [<c0365d38>] (ams_delta_init_fiq+0xa8/0x160)
r6:00000164 r5:c001b110 r4:00000000 r3:fefecb4c
[<c0365c90>] (ams_delta_init_fiq+0x0/0x160) from [<c0365b14>] (ams_delta_init+0xd4/0x114)
r6:00000000 r5:fffece10 r4:c037a9e0
[<c0365a40>] (ams_delta_init+0x0/0x114) from [<c03613b4>] (customize_machine+0x24/0x30)
This is because the vectors page is now write-protected, and to change
code in there we must write to its original alias. Make that change,
and adjust the cache flushing such that the code will become visible
to the instruction stream on VIVT CPUs.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When using 64kB pages, we only have two levels of page tables,
meaning that PGD, PUD and PMD are fused. In this case, trying
to refcount PUDs and PMDs independently is a a complete disaster,
as they are the same.
We manage to get it right for the allocation (stage2_set_pte uses
{pmd,pud}_none), but the unmapping path clears both pud and pmd
refcounts, which fails spectacularly with 2-level page tables.
The fix is to avoid calling clear_pud_entry when both the pmd and
pud pages are empty. For this, and instead of introducing another
pud_empty function, consolidate both pte_empty and pmd_empty into
page_empty (the code is actually identical) and use that to also
test the validity of the pud.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The unmap_range function did not properly cover the case when the start
address was not aligned to PMD_SIZE or PUD_SIZE and an entire pte table
or pmd table was cleared, causing us to leak memory when incrementing
the addr.
The fix is to always move onto the next page table entry boundary
instead of adding the full size of the VA range covered by the
corresponding table level entry.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Fix yet another build failure caused by a weird set of configuration
settings:
LD init/built-in.o
arch/arm/kernel/built-in.o: In function `__dabt_usr':
/home/tom3q/kernel/arch/arm/kernel/entry-armv.S:377: undefined reference to `kuser_cmpxchg64_fixup'
arch/arm/kernel/built-in.o: In function `__irq_usr':
/home/tom3q/kernel/arch/arm/kernel/entry-armv.S:387: undefined reference to `kuser_cmpxchg64_fixup'
caused by:
CONFIG_KUSER_HELPERS=n
CONFIG_CPU_32v6K=n
CONFIG_NEEDS_SYSCALL_FOR_CMPXCHG=n
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The PAR was exported as CRn == 7 and CRm == 0, but in fact the primary
coprocessor register number was determined by CRm for 64-bit coprocessor
registers as the user space API was modeled after the coprocessor
access instructions (see the ARM ARM rev. C - B3-1445).
However, just changing the CRn to CRm breaks the sorting check when
booting the kernel, because the internal kernel logic always treats CRn
as the primary register number, and it makes the table sorting
impossible to understand for humans.
Alternatively we could change the logic to always have CRn == CRm, but
that becomes unclear in the number of ways we do look up of a coprocessor
register. We could also have a separate 64-bit table but that feels
somewhat over-engineered. Instead, keep CRn the primary representation
of the primary coproc. register number in-kernel and always export the
primary number as CRm as per the existing user space ABI.
Note: The TTBR registers just magically worked because they happened to
follow the CRn(0) regs and were considered CRn(0) in the in-kernel
representation.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
When CONFIG_PREEMPT is enabled, Linux will not be able to boot and warn:
[ 4.127825] ------------[ cut here ]------------
[ 4.133376] WARNING: at init/main.c:699 do_one_initcall+0x150/0x158()
[ 4.140738] initcall xen_init_events+0x0/0x10c returned with preemption imbalance
This is because xen_percpu_init uses get_cpu but doesn't have the corresponding
put_cpu.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
This was missed when splitting out the phy from the controller node in
commit 9dffe3be3f32 (ARM: tegra: modify ULPI reset GPIO properties).
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch removes sti_secondary_start from _INIT section, there are 2
reason for this removal.
1. discarding such a small code does not save much, given the RAM
sizes.
2. Having this code discarded, creates corruption issue when we boot
smp-kernel with nrcpus=1 or with single cpu node in DT.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes cpu nodes with device_type = "cpu". This change was not
necessary before 3.10-rc7.
Without this patch STi SOCs does not boot as SMP.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second round of Renesas ARM based SoC fixes for v3.11
* Lager board: do not annotate gpio_buttons as __initdata
- This avoids accessing uninitialised memory if keys are pressed
after kernel initialisation completes.
- Bug introduced in gpio-keys were enabled in v3.11-rc1
* Bock-W board: fix SDHI0 PFC settings
- Allow detection of SD card
- Bug introduced in SDHI support was added in v3.11-rc1
* shdma: fixup sh_dmae_get_partial() calculation error
- Bug introduced in 2.6.34-rc1.
* armadillo800eva board: Don't request GPIO 166 in board code
- Allow use of touchscreen
- Bug introduced in v3.11-rc1
* tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley via Tony Lindgren:
Some OMAP hwmod fixes for v3.11-rc. Mostly intended to fix an earlyprintk
regression and an AM33xx cpgmac power management regression.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_a_v3.11-rc/20130730042132/
The tests include temporary fixes for the unrelated 2430SDP and OMAP3
boot regressions, which are not part of this signed tag.
* tag 'for-v3.11-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fixes for omap5-uevm regulators from Nishanth Menon <nm@ti.com>:
Due to wrong older revision of documentation used as reference, we
seem to have a bunch of LDOs wrongly configured on OMAP5 uEVM. This
series is based power tree on production board 750-2628-XXX platform.
Unfortunately, the wrong voltages may be detrimental to OMAP5 as they
supply hardware blocks at voltages that are out of specification.
There is a chance that without these fixes there can be hardware
damage to omap5-uevm boards with the v3.11-rc series.
* tag 'omap-for-v3.11/fixes-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown, fixes for MSM for 3.11:
Two small fixes for MSM.
The first fixes the a gpio controller register address. I didn't see
any acks from the devicetree maintainers, so I've copied them on this
pull request. The change itself is minor, and just to the register
address.
The second change removes the gpiomux V1 code from MSM. This was
breaking compilation for some of the targets.
* tag 'msm-3.11-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Consolidate gpiomux for older architectures
ARM: msm: dts: Fix the gpio register address for msm8960
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull arm fixes fixes from Russell King:
"This fixes a couple of problems with commit 48be69a026b2 ("ARM: move
signal handlers into a vdso-like page"), one of which was originally
discovered via my testing originally, but the fix for it was never
actually committed.
The other shows up on noMMU builds, and such platforms are extremely
rare and as such are not part of my nightly testing"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix nommu builds with 48be69a02 (ARM: move signal handlers into a vdso-like page)
ARM: fix a cockup in 48be69a02 (ARM: move signal handlers into a vdso-like page)
|
|
|
|
vdso-like page)
Olof reports that noMMU builds error out with:
arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'
This shows one of the evilnesses of IS_ENABLED(). Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Unfortunately, I never committed the fix to a nasty oops which can
occur as a result of that commit:
------------[ cut here ]------------
kernel BUG at /home/olof/work/batch/include/linux/mm.h:414!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe0308 #53
task: e90acac0 ti: e9be8000 task.ti: e9be8000
PC is at special_mapping_fault+0xa4/0xc4
LR is at __do_fault+0x68/0x48c
This doesn't show up unless you do quite a bit of testing; a simple
boot test does not do this, so all my nightly tests were passing fine.
The reason for this is that install_special_mapping() expects the
page array to stick around, and as this was only inserting one page
which was stored on the kernel stack, that's why this was blowing up.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull ARM fixes from Russell King:
"I've thought long and hard about what to say for this pull request,
and I really can't work out anything sane to say to summarise much of
these commits. The problem is, for most of these are, yet again, lots
of small bits scattered around the place without any real overall
theme to them"
Most notable is probably the kuser page helper improvements.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (22 commits)
ARM: Add .text annotations where required after __CPUINIT removal
ARM: 7803/1: Fix deadlock scenario with smp_send_stop()
ARM: make vectors page inaccessible from userspace
ARM: move signal handlers into a vdso-like page
ARM: allow kuser helpers to be removed from the vector page
ARM: update FIQ support for relocation of vectors
ARM: use linker magic for vectors and vector stubs
ARM: move vector stubs
ARM: poison memory between kuser helpers
ARM: poison the vectors page
ARM: 7801/1: v6: prevent gcc 4.5 from reordering extended CP15 reads above is_smp() test
ARM: 7800/1: ARMv7-M: Fix name of NVIC handler function
ARM: Fix sorting of machine- initializers
ARM: 7791/1: a.out: remove partial a.out support
ARM: 7790/1: Fix deferred mm switch on VIVT processors
ARM: 7789/1: Do not run dummy_flush_tlb_a15_erratum() on non-Cortex-A15
ARM: 7787/1: virt: ensure visibility of __boot_cpu_mode
ARM: 7788/1: elf: fix lpae hwcap feature reporting in proc/cpuinfo
ARM: 7786/1: hyp: fix macro parameterisation
ARM: 7785/1: mm: restrict early_alloc to section-aligned memory
...
|
|
Panda's DVI connector's DDC pins are connected to OMAP's third i2c bus.
With non-DT, the bus number was 3, and that is what is used in the
dss-common.c which contains the platform data for Panda's DVI.
However, with DT, the bus number is 2. As we now only have DT boot for
Panda, we have to change the bus number to make DVI EDID read
operational.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
|
