summaryrefslogtreecommitdiffstats
path: root/arch/arm
AgeCommit message (Collapse)AuthorFilesLines
2016-02-18arm64: kvm: deal with kernel symbols outside of linear mappingArd Biesheuvel2-3/+7
KVM on arm64 uses a fixed offset between the linear mapping at EL1 and the HYP mapping at EL2. Before we can move the kernel virtual mapping out of the linear mapping, we have to make sure that references to kernel symbols that are accessed via the HYP mapping are translated to their linear equivalent. Reviewed-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2016-02-14Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds1-2/+7
Pull ARM fixes from Russell King: "A couple of ARM fixes from Linus for the ICST clock generator code" [ "Linus" here is Linus Walleij. Name-stealer. Linus "there can be only one" Torvalds ] * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8519/1: ICST: try other dividends than 1 ARM: 8517/1: ICST: avoid arithmetic overflow in icst_hz()
2016-02-12Merge tag 'fbdev-fixes-4.5' of ↵Linus Torvalds1-17/+16
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux Pull fbdev fixes from Tomi Valkeinen: - fix omap2plus_defconfig to enable omapfb as it was in v4.4 - ocfb: fix timings for margins - s6e8ax0, da8xx-fb: fix compile warnings - mmp: fix build failure caused by bad printk parameters - imxfb: fix clock issue which kept the display off * tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: video: fbdev: imxfb: Provide a reset mechanism fbdev: mmp: print IRQ resource using %pR format string fbdev: da8xx-fb: remove incorrect type cast fbdev: s6e8ax0: avoid unused function warnings ocfb: fix tgdel and tvdel timing parameters ARM: omap2plus_defconfig: update display configs
2016-02-11ARM: 8519/1: ICST: try other dividends than 1Linus Walleij1-0/+1
Since the dawn of time the ICST code has only supported divide by one or hang in an eternal loop. Luckily we were always dividing by one because the reference frequency for the systems using the ICSTs is 24MHz and the [min,max] values for the PLL input if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop will always terminate immediately without assigning any divisor for the reference frequency. But for the code to make sense, let's insert the missing i++ Reported-by: David Binderman <dcb314@hotmail.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-02-08ARM: 8517/1: ICST: avoid arithmetic overflow in icst_hz()Linus Walleij1-2/+6
When trying to set the ICST 307 clock to 25174000 Hz I ran into this arithmetic error: the icst_hz_to_vco() correctly figure out DIVIDE=2, RDW=100 and VDW=99 yielding a frequency of 25174000 Hz out of the VCO. (I replicated the icst_hz() function in a spreadsheet to verify this.) However, when I called icst_hz() on these VCO settings it would instead return 4122709 Hz. This causes an error in the common clock driver for ICST as the common clock framework will call .round_rate() on the clock which will utilize icst_hz_to_vco() followed by icst_hz() suggesting the erroneous frequency, and then the clock gets set to this. The error did not manifest in the old clock framework since this high frequency was only used by the CLCD, which calls clk_set_rate() without first calling clk_round_rate() and since the old clock framework would not call clk_round_rate() before setting the frequency, the correct values propagated into the VCO. After some experimenting I figured out that it was due to a simple arithmetic overflow: the divisor for 24Mhz reference frequency as reference becomes 24000000*2*(99+8)=0x132212400 and the "1" in bit 32 overflows and is lost. But introducing an explicit 64-by-32 bit do_div() and casting the divisor into (u64) we get the right frequency back, and the right frequency gets set. Tested on the ARM Versatile. Cc: stable@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-02-04ARM: multi_v7_defconfig: enable DW_WATCHDOGDinh Nguyen1-0/+1
The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog. Enable CONFIG_DW_WATCHDOG for the driver to get built. Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-04ARM: nomadik: fix up SD/MMC DT settingsLinus Walleij1-17/+20
The DTSI file for the Nomadik does not properly specify how the PL180 levelshifter is connected: the Nomadik actually needs all the five st,sig-dir-* flags set to properly control all lines out. Further this board supports full power cycling of the card, and since this variant has no hardware clock gating, it needs a ridiculously low frequency setting to keep up with the ever overflowing FIFO. The pin configuration set-up is a bit of a mystery, because of course these pins are a mix of inputs and outputs. However the reference implementation sets all pins to "output" with unspecified initial value, so let's do that here as well. Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01Merge tag 'mvebu-fixes-4.5-1' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson5-31/+35
mvebu fixes for 4.5 (part 1) - Fix dts on buffalo linksations machines (gpios and leds) - Fix dts partition node according to new binding introduced in v4.5 * tag 'mvebu-fixes-4.5-1' of git://git.infradead.org/linux-mvebu: ARM: dts: orion5x: gpio pin fixes for linkstation lswtgl ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vl ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxl ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vl ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxl ARM: mvebu: ix4-300d: Add compatible property to "partitions" node ARM: mvebu: kirkwood: Add compatible property to "partitions" node Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01Merge tag 'omap-for-v4.5/fixes-rc1' of ↵Olof Johansson13-91/+130
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omaps with the most intrusive stuff being read-only data assembly fixes, the other things are mostly board related: - A series of omap assembly code fixes to fix issues with rodata with ARM_KERNMEM_PERMS enabled. We had several places writing to rodata, which is bad. The fix in most cases is to load the value from data section using a pointer. Let's also enable ARM_KERNMEM_PERMS so DEBUG_RODATA gets selected by default. And while testing things, I also added few more loadable driver modules to the defconfig that I seem to need quite often. - Fix a long standing omap5 RTC mystery and enable RTC where we need to ensure the SoC msecure pin is high so we can write to the RTC registers. - Fix irq types for am437x - A series of minor dts fixes for sbc-am57x and cl-som-am57x - Fixes for torpedo dts to make WLAN behave and to remove a duplicate i2c rate entry This series also includes few minor changes that are not stricly fixes, but would be good to get in during the early -rc cycle: - Remove legacy mailbox platform data that is no longer needed - Add the pdata-quirks needed for the new pwm-omap-dmtimer so people can use it - Enable ti,mbox-send-noirq that's needed by wkup_m3 driver - Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the initramfs quite a bit smaller * tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits) ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2 ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address ARM: dts: LogicPD Torpedo: Revert Duplicative Entries ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types ARM: dts: am4372: fix irq type for arm twd and global timer ARM: dts: Fix wl12xx missing clocks that cause hangs ARM: OMAP: Add PWM dmtimer platform data quirks ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata ARM: OMAP2+: Fix l2_inv_api_params for rodata ARM: OMAP2+: Fix save_secure_ram_context for rodata ARM: OMAP2+: Fix l2dis_3630 for rodata ARM: OMAP2+: Fix wait_dll_lock_timed for rodata ARM: OMAP2+: Remove legacy mailbox device instantiation ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox ... Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01Merge tag 'at91-fixes' of ↵Olof Johansson5-4/+31
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes First fixes for 4.5. Only DT changes: - sama5d4: error in DBGU index - addition of phy properties in several boards - at91sam9n12ek fix a panel compatible string * tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0 ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0 ARM: dts: at91: at91sam9n12ek: fix panel compatible string ARM: dts: at91: sama5d4: fix instance id of DBGU Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01ARM: realview: use "depends on" instead of "if" after promptMasahiro Yamada1-1/+2
This platform recently moved to multi-platform, so missed the global fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs instead of "if" after prompt"). Fix it now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01ARM: tango: use "depends on" instead of "if" after promptMasahiro Yamada1-1/+2
This platform was recently added, so missed the global fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs instead of "if" after prompt"). Fix it now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01ARM: tango: use const and __initconst for smp_operationsMasahiro Yamada1-1/+1
This newly added code missed the global fixup by commit 75305275a721 ("ARM: use const and __initconst for smp_operations"). So fix it now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-02-01ARM: realview: use const and __initconst for smp_operationsMasahiro Yamada1-1/+1
This newly added code missed the global fixup by commit 75305275a721 ("ARM: use const and __initconst for smp_operations"). So fix it now. Also, add missing "static" qualifier. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2016-01-29ARM: omap2plus_defconfig: update display configsTomi Valkeinen1-17/+16
omapfb and omapdrm were recently made independent of each other, and this required Kconfig option changes. This patch changes the omap2plus_defconfig to enable display similarly as before: omapfb and panel & encoder drivers as modules. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: wire up copy_file_range() syscallRussell King2-0/+2
Add the copy_file_range() syscall to ARM. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-01-27ARM: dts: am57xx: sbc-am57x: correct Eth PHY settingsDmitry Lifshitz1-2/+2
Update Eth PHY settings to make it possible to run both phys at 1Gbps. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmuxDmitry Lifshitz1-1/+1
Fix CPSW EMAC pinmux Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am57xx: sbc-am57x: fix UART3 pinmuxDmitry Lifshitz1-2/+2
Fix UART3 pinmux. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequencyDmitry Lifshitz1-2/+2
On-board SPI flash cat act at 48Mhz SPI bus frequency. Update the DT frequency property. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2Dmitry Lifshitz1-1/+1
Setup USB2 to act in "HOST" mode by default. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C addressDmitry Lifshitz1-2/+2
Fix SB-SOM EEPROM I2C address Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: LogicPD Torpedo: Revert Duplicative EntriesAdam Ford1-8/+0
Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit") It was already done and it is just a duplicate. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am437x: pixcir_tangoc: use correct flags for irq typesGrygorii Strashko2-4/+2
Now IRQs for Pixcir Tangoc touchscreen are defined using IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich do not correspond HW. Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files and use correct flag IRQ_TYPE_EDGE_FALLING for irq types. While here, remove duplicated irq declaration for pixcir_ts@5c node in am437x-gp-evm.dts. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: am4372: fix irq type for arm twd and global timerGrygorii Strashko1-2/+2
As per ARM documentation PPI(0) ID27 - global timer interrupt is rising-edge sensitive. PPI(2) ID29 - twd interrupt is rising-edge sensitive. and the same is proved by GIC distributor register value GIC_DIST_CONFIG(0xC04) = 0x7DC00000. Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING for ARM TWD and Global timers. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-27ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ typeNicolas Ferre1-1/+1
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of "edge falling". Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: <stable@vger.kernel.org> # 4.1+
2016-01-27ARM: dts: at91: sama5d4 xplained: properly mux phy interruptAlexandre Belloni1-0/+6
No interrupt were received from the phy because PIOE 1 may not be properly muxed. It prevented proper link detection, especially since commit 321beec5047a ("net: phy: Use interrupts when available in NOLINK state") disables polling. Cc: <stable@vger.kernel.org> # 4.4 Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-27ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0Wenyou Yang1-0/+11
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend state. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> [nicolas.ferre@atmel.com: adapt to newer kernel] Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: <stable@vger.kernel.org> # 4.1+ Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-27ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0Nicolas Ferre1-1/+11
After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091) the macb0 interface has difficulties to come back from power saving mode if address not explicitly set up. As the micrel phy on the board is actually configured to show up at address 1 we use this explicitly. Adding the phy node and its real address fixes the issue. The phy IRQ and associated pinmux node is also added. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
2016-01-27ARM: dts: at91: at91sam9n12ek: fix panel compatible stringAlexandre Belloni1-1/+1
Properly use qiaodian as the vendor prefix for the panel. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-27ARM: dts: at91: sama5d4: fix instance id of DBGUMohamed Jamsheeth Hajanajubudeen1-1/+1
Change instance id of DBGU to 45. Signed-off-by: Mohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com> Fixes: 7c661394c56c ("ARM: at91: dt: add device tree file for SAMA5D4 SoC") Cc: stable@vger.kernel.org # 3.18+ Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-26ARM: 8500/1: fix atags_to_fdt with stack-protector-strongKees Cook1-0/+9
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for being able to use any of the stack_chk code. Explicitly disable it for only the atags_to_fdt bits. Suggested-by: zhxihu <zhxihu@marvell.com> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-01-25ARM: dts: Fix wl12xx missing clocks that cause hangsAdam Ford1-0/+1
The tcxo-clock-frequency binding is listed as optional, but without it the wl12xx used on the torpedo + wireless may hang. Scanning also appears broken without this patch. Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-25Merge branch 'enable-devices' into omap-for-v4.5/fixesTony Lindgren920-9727/+25687
2016-01-25ARM: OMAP: Add PWM dmtimer platform data quirksNeil Armstrong1-0/+23
In order to set the currently platform dependent dmtimer functions pointers as platform data for the pwm-omap-dmtimer platform driver, add it to plat-omap auxdata_lookup table. Suggested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-25ARM: dts: orion5x: gpio pin fixes for linkstation lswtglRoger Shimizu1-4/+4
Here're a few gpio pin related fixes: - remove pinctrl-0 definition from pinctrl, since those pins are used in other places such as gpio-fan and regulators. - keep initial state of power led - fix for alarm pin of gpio-fan. Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl") Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vlRoger Shimizu1-6/+6
The GPIOs controlling the LEDs, listed below, are active high, not low: - gpio-leds: "lswvl:red:alarm" pin - gpio-leds: "lswvl:red:func" pin - gpio-leds: "lswvl:amber:info" pin - gpio-leds: "lswvl:blue:func" pin - gpio-leds: "lswvl:red:hdderr{0,1}" pin Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl") Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxlRoger Shimizu1-5/+5
The GPIOs controlling the LEDs, listed below, are active high, not low: - gpio-leds: "lswxl:blue:power" pin - gpio-leds: "lswxl:red:func" pin - gpio-leds: "lswxl:red:hdderr{0,1}" pin Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl") Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vlRoger Shimizu1-12/+13
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be converted to "gpio1 <pin minus 32>" in dts file. e.g. gpio 40 should be "gpio1 8" The pin/bank issue was found when discussing Debian Bug #810894 [https://bugs.debian.org/810894#47] Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl") Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org> Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxlRoger Shimizu1-14/+15
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be converted to "gpio1 <pin minus 32>" in dts file. e.g. gpio 40 should be "gpio1 8" Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin definition: - gpio-leds: "lswxl:blue:power" pin - gpio-leds: "lswxl:red:func" pin - gpio-leds: "lswxl:red:hdderr0" pin - gpio-leds: "lswxl:red:hdderr1" pin - gpio-fan: low/high/alarm pin The pin/bank issue was found when discussing Debian Bug #810894 [https://bugs.debian.org/810894#47] Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl") Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org> Signed-off-by: Roger Shimizu <rogershimizu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: mvebu: ix4-300d: Add compatible property to "partitions" nodeGeert Uytterhoeven1-0/+1
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-25ARM: mvebu: kirkwood: Add compatible property to "partitions" nodeGeert Uytterhoeven1-0/+1
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-01-23Merge branch 'akpm' (patches from Andrew)Linus Torvalds1-9/+2
Merge small final update from Andrew Morton: - DAX feature work: add fsync/msync support - kfree cleanup, MAINTAINERS update * emailed patches from Andrew Morton <akpm@linux-foundation.org>: MAINTAINERS: return arch/sh to maintained state, with new maintainers tree wide: use kvfree() than conditional kfree()/vfree() dax: never rely on bh.b_dev being set by get_block() xfs: call dax_pfn_mkwrite() for DAX fsync/msync ext4: call dax_pfn_mkwrite() for DAX fsync/msync ext2: call dax_pfn_mkwrite() for DAX fsync/msync dax: add support for fsync/sync mm: add find_get_entries_tag() dax: support dirty DAX entries in radix tree pmem: add wb_cache_pmem() to the PMEM API dax: fix conversion of holes to PMDs dax: fix NULL pointer dereference in __dax_dbg()
2016-01-22Merge tag 'armsoc-tegra' of ↵Linus Torvalds3-52/+6
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC support for Tegra platforms from Olof Johansson: "Here's a single-SoC topic branch that we've staged separately. Mainly because it was hard to sort the branch contents in a way that fit our existing branches due to some refactorings. The code has been in -next for quite a while, but we staged it in arm-soc a bit late, which is why we've kept it separate from the other updates and are sending it separately here" * tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support arm64: tegra: Add NVIDIA P2597 I/O board support arm64: tegra: Add NVIDIA Jetson TX1 support arm64: tegra: Add NVIDIA P2571 board support arm64: tegra: Add NVIDIA P2371 board support arm64: tegra: Add NVIDIA P2595 I/O board support arm64: tegra: Add NVIDIA P2530 main board support arm64: tegra: Add Tegra210 support arm64: tegra: Add NVIDIA Tegra132 Norrin support arm64: tegra: Add Tegra132 support ARM: tegra: select USB_ULPI from EHCI rather than platform ARM: tegra: Ensure entire dcache is flushed on entering LP0/1 amba: Hide TEGRA_AHB symbol soc/tegra: Add Tegra210 support soc/tegra: Provide per-SoC Kconfig symbols
2016-01-22Merge tag 'armsoc-fixes' of ↵Linus Torvalds3-14/+8
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "A few fixes for fallout that we didn't catch in time in -next, or smaller warning fixes that have been discovered since" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: soc: qcom/spm: shut up uninitialized variable warning ARM: realview: fix device tree build ARM: debug-ll: fix BCM63xx entry for multiplatform ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
2016-01-22tree wide: use kvfree() than conditional kfree()/vfree()Tetsuo Handa1-9/+2
There are many locations that do if (memory_was_allocated_by_vmalloc) vfree(ptr); else kfree(ptr); but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory using is_vmalloc_addr(). Unless callers have special reasons, we can replace this branch with kvfree(). Please check and reply if you found problems. Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Jan Kara <jack@suse.com> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Andreas Dilger <andreas.dilger@intel.com> Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net> Acked-by: David Rientjes <rientjes@google.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Oleg Drokin <oleg.drokin@intel.com> Cc: Boris Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-01-22Merge tag 'renesas-fixes-for-v4.5' of ↵Olof Johansson1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes Renesas ARM Based SoC Fixes for v4.5 Correct extal1 frequency of armadillo800eva board * tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz Signed-off-by: Olof Johansson <olof@lixom.net>
2016-01-22ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modulesTony Lindgren1-0/+8
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that DEBUG_RODATA gets selected by default. This way we can make sure any related issues are caught early. And while testing things on various devices, I noticed we're missing few loadable modules to make things more usable: - USB Ethernet for smsc75xx, we only have smsc97xx right now - Basic USB serial drivers for things like ftdi and pl2303 ports - Blinking leds with pca963x Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-22ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodataTony Lindgren1-8/+17
We don't want to write to .text so let's move ppa_zero_params and ppa_por_params to .data and access them via pointers. Note that I have not been able to test as we I don't have a HS omap4 to test with. The code has been changed in similar way as for omap3 though. Cc: Kees Cook <keescook@chromium.org> Cc: Laura Abbott <labbott@redhat.com> Cc: Nishanth Menon <nm@ti.com> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Acked-by: Nicolas Pitre <nico@linaro.org> Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren <tony@atomide.com>
2016-01-22ARM: OMAP2+: Fix l2_inv_api_params for rodataTony Lindgren1-3/+9
We don't want to write to .text, so let's move l2_inv_api_params to .data and access it via a pointer. Cc: Kees Cook <keescook@chromium.org> Cc: Laura Abbott <labbott@redhat.com> Cc: Nishanth Menon <nm@ti.com> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Acked-by: Nicolas Pitre <nico@linaro.org> Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-30 15:57:06 +0000