| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are for MMP (seeing a bunch of cleanups and refactorings
for the first time in a while), and for OMAP (a bunch of cleanups and
added support for voltage controller on OMAP4430)"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Add missing put_device() call in omapdss_init_of()
OMAP2: fixup doc comments in omap_device
ARM: OMAP1: drop duplicated dependency on ARCH_OMAP1
ARM: ASPEED: update default ARCH_NR_GPIO for ARCH_ASPEED
ARM: imx: use generic function to exit coherency
ARM: tegra: Use WFE for power-gating on Tegra30
ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()
ARM: exynos: Enable exynos-asv driver for ARCH_EXYNOS
ARM: s3c: Rename s5p_usb_phy functions
ARM: s3c: Rename s3c64xx_spi_setname() function
ARM: imx: Add serial number support for i.MX6/7 SoCs
ARM: imx: Drop imx_anatop_usb_chrg_detect_disable()
arm64: Introduce config for S32
ARM: hisi: drop useless depend on ARCH_MULTI_V7
arm64: realtek: Select reset controller
ARM: shmobile: rcar-gen2: Drop legacy DT clock support
ARM: OMAP2+: Remove duplicated include from pmic-cpcap.c
ARM: OMAP1: ams-delta FIQ: Fix a typo ("Initiaize")
MAINTAINERS: Add logicpd-som-lv and logicpd-torpedo to OMAP TREE
ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support
...
|
|
The generic nommu implementation of page table manipulation takes care
of folding of the upper levels and does not require fixups.
Simply replace of include/asm-generic/4level-fixup.h with
include/asm-generic/pgtable-nopud.h.
Link: http://lkml.kernel.org/r/1572938135-31886-3-git-send-email-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Peter Rosin <peda@axentia.se>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Follow the kernel conventions, rename addr_in_gen_pool to
gen_pool_has_addr.
[sjhuang@iluvatar.ai: fix Documentation/ too]
Link: http://lkml.kernel.org/r/20181229015914.5573-1-sjhuang@iluvatar.ai
Link: http://lkml.kernel.org/r/20181228083950.20398-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix build error in crypto lib code when crypto API is off
- Fix NULL/error check in hisilicon
- Fix Kconfig-related build error in talitos
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon - fix a NULL vs IS_ERR() bug in sec_create_qp_ctx()
crypto: talitos - Fix build error by selecting LIB_DES
crypto: arch - conditionalize crypto api in arch glue for lib code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Add support for an enable GPIO; lm3630a_bl
- Add support for short circuit handling; qcom-wled
- Add support for automatic string detection; qcom-wled
Fix-ups:
- Update Device Tree bindings; lm3630a-backlight, led-backlight,
qcom-wled
- Constify; ipaq_micro_bl
- Optimise for CPU cycles; pwm_bl
- Coding style fix-ups; pwm_bl
- Trivial fix-ups (white space, comments, renaming); pwm_bl,
gpio_backlight, qcom-wled
- Kconfig dependency hacking; LCD_HP700
- Rename, refactor and add peripherals; pm8941-wled => qcom-wled
- Make use of GPIO look-up tables; tosa_bl, tosa_lcd
- Remove superfluous code; gpio_backlight
- Adapt GPIO direction handling; gpio_backlight
- Remove legacy use of platform data; gpio_backlight
Bug Fixes:
- Provide modules aliases; lm3630a_bl"
* tag 'backlight-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (32 commits)
backlight: qcom-wled: Fix spelling mistake "trigged" -> "triggered"
backlight: gpio: Pull gpio_backlight_initial_power_state() into probe
backlight: gpio: Use a helper variable for &pdev->dev
backlight: gpio: Remove unused fields from platform data
sh: ecovec24: don't set unused fields in platform data
backlight: gpio: Simplify the platform data handling
sh: ecovec24: add additional properties to the backlight device
backlight: gpio: Explicitly set the direction of the GPIO
backlight: gpio: Remove stray newline
backlight: gpio: Remove unneeded include
video: backlight: tosa: Use GPIO lookup table
backlight: qcom-wled: Add auto string detection logic
backlight: qcom-wled: Add support for short circuit handling
backlight: qcom-wled: Add support for WLED4 peripheral
backlight: qcom-wled: Restructure the driver for WLED3
backlight: qcom-wled: Rename PM8941* to WLED3
backlight: qcom-wled: Add new properties for PMI8998
backlight: qcom-wled: Restructure the qcom-wled bindings
backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c
dt-bindings: backlight: lm3630a: Fix missing include
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull sysctl system call removal from Eric Biederman:
"As far as I can tell we have reached the point where no one enables
the sysctl system call anymore. It still is enabled in a few
defconfigs but they are mostly the rarely used one and in asking
people about that it was more cut & paste enabled than anything else.
This is single commit that just deletes code. Leaving just enough code
so that the deprecated sysctl warning continues to be printed. If my
analysis turns out to be wrong and someone actually cares it will be
easy to revert this commit and have the system call again.
There was one new xtensa defconfig in linux-next that enabled the
system call this cycle and when asked about it the maintainer of the
code replied that it was not enabled on purpose. As of today's
linux-next tree that defconfig no longer enables the system call.
What we saw in the review discussion was that if we go a step farther
than my patch and mess with uapi headers there are pieces of code that
won't compile, but nothing minds the system call actually disappearing
from the kernel"
Link: https://lore.kernel.org/lkml/201910011140.EA0181F13@keescook/
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Remove the sysctl system call
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"Mostly this is implementing the new flag SECCOMP_USER_NOTIF_FLAG_CONTINUE,
but there are cleanups as well.
- implement SECCOMP_USER_NOTIF_FLAG_CONTINUE (Christian Brauner)
- fixes to selftests (Christian Brauner)
- remove secure_computing() argument (Christian Brauner)"
* tag 'seccomp-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: rework define for SECCOMP_USER_NOTIF_FLAG_CONTINUE
seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test
seccomp: simplify secure_computing()
seccomp: test SECCOMP_USER_NOTIF_FLAG_CONTINUE
seccomp: add SECCOMP_USER_NOTIF_FLAG_CONTINUE
seccomp: avoid overflow in implicit constant conversion
|
|
Pull ARM updates from Russell King:
- improve ARM implementation of pfn_valid()
- various sparse fixes
- spelling fixes
- add further ARMv8 debug architecture versions
- clang fix for decompressor
- update to generic vDSO
- remove Brahma-B53 from spectre hardening
- initialise broadcast hrtimer device
- use correct nm executable in decompressor
- remove old mcount et.al.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (26 commits)
ARM: 8940/1: ftrace: remove mcount(),ftrace_caller_old() and ftrace_call_old()
ARM: 8939/1: kbuild: use correct nm executable
ARM: 8938/1: kernel: initialize broadcast hrtimer based clock event device
ARM: 8937/1: spectre-v2: remove Brahma-B53 from hardening
ARM: 8933/1: replace Sun/Solaris style flag on section directive
ARM: 8932/1: Add clock_gettime64 entry point
ARM: 8931/1: Add clock_getres entry point
ARM: 8930/1: Add support for generic vDSO
ARM: 8929/1: use APSR_nzcv instead of r15 as mrc operand
ARM: 8927/1: ARM/hw_breakpoint: add more ARMv8 debug architecture versions support
ARM: 8918/2: only build return_address() if needed
ARM: 8928/1: ARM_ERRATA_775420: Spelling s/date/data/
ARM: 8925/1: tcm: include <asm/tcm.h> for missing declarations
ARM: 8924/1: tcm: make dtcm_end and itcm_end static
ARM: 8923/1: mm: include <asm/vga.h> for vga_base
ARM: 8922/1: parse_dt_topology() rate is pointer to __be32
ARM: 8920/1: share get_signal_page from signal.c to process.c
ARM: 8919/1: make unexported functions static
ARM: 8917/1: mm: include <asm/set_memory.h>
ARM: 8916/1: mm: make set_section_perms() static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux; tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using DMA offsets
(Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas
Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
* tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits)
dma-mapping: treat dev->bus_dma_mask as a DMA limit
dma-direct: exclude dma_direct_map_resource from the min_low_pfn check
dma-direct: don't check swiotlb=force in dma_direct_map_resource
dma-debug: clean up put_hash_bucket()
powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys
dma-direct: avoid a forward declaration for phys_to_dma
dma-direct: unify the dma_capable definitions
dma-mapping: drop the dev argument to arch_sync_dma_for_*
x86/PCI: sta2x11: use default DMA address translation
dma-direct: check for overflows on 32 bit DMA addresses
dma-debug: increase HASH_SIZE
dma-debug: reorder struct dma_debug_entry fields
xtensa: use the generic uncached segment support
dma-mapping: merge the generic remapping helpers into dma-direct
dma-direct: provide mmap and get_sgtable method overrides
dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages
dma-direct: remove __dma_direct_free_pages
usb: core: Remove redundant vmap checks
kernel: dma-contiguous: mark CMA parameters __initdata/__initconst
dma-debug: add a schedule point in debug_dma_dump_mappings()
...
|
|
Pull generic ioremap support from Christoph Hellwig:
"This adds the remaining bits for an entirely generic ioremap and
iounmap to lib/ioremap.c. To facilitate that, it cleans up the giant
mess of weird ioremap variants we had with no users outside the arch
code.
For now just the three newest ports use the code, but there is more
than a handful others that can be converted without too much work.
Summary:
- clean up various obsolete ioremap and iounmap variants
- add a new generic ioremap implementation and switch csky, nds32 and
riscv over to it"
* tag 'ioremap-5.5' of git://git.infradead.org/users/hch/ioremap: (21 commits)
nds32: use generic ioremap
csky: use generic ioremap
csky: remove ioremap_cache
riscv: use the generic ioremap code
lib: provide a simple generic ioremap implementation
sh: remove __iounmap
nios2: remove __iounmap
hexagon: remove __iounmap
m68k: rename __iounmap and mark it static
arch: rely on asm-generic/io.h for default ioremap_* definitions
asm-generic: don't provide ioremap for CONFIG_MMU
asm-generic: ioremap_uc should behave the same with and without MMU
xtensa: clean up ioremap
x86: Clean up ioremap()
parisc: remove __ioremap
nios2: remove __ioremap
alpha: remove the unused __ioremap wrapper
hexagon: clean up ioremap
ia64: rename ioremap_nocache to ioremap_uc
unicore32: remove ioremap_cached
...
|
|
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
|
|
For glue code that's used by Zinc, the actual Crypto API functions might
not necessarily exist, and don't need to exist either. Before this
patch, there are valid build configurations that lead to a unbuildable
kernel. This fixes it to conditionalize those symbols on the existence
of the proper config entry.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include cpuidle changes to use nanoseconds (instead of
microseconds) as the unit of time and to simplify checks for disabled
idle states in the idle loop, some cpuidle fixes and governor updates,
assorted cpufreq updates (driver updates mostly and a few core fixes
and cleanups), devfreq updates (dominated by the tegra30 driver
changes), new CPU IDs for the RAPL power capping driver, relatively
minor updates of the generic power domains (genpd) and operation
performance points (OPP) frameworks, and assorted fixes and cleanups.
There are also two maintainer information updates: Chanwoo Choi will
be maintaining the devfreq subsystem going forward and Todd Brandt is
going to maintain the pm-graph utility (created by him).
Specifics:
- Use nanoseconds (instead of microseconds) as the unit of time in
the cpuidle core and simplify checks for disabled idle states in
the idle loop (Rafael Wysocki)
- Fix and clean up the teo cpuidle governor (Rafael Wysocki)
- Fix the cpuidle registration error code path (Zhenzhong Duan)
- Avoid excessive vmexits in the ACPI cpuidle driver (Yin Fengwei)
- Extend the idle injection infrastructure to be able to measure the
requested duration in nanoseconds and to allow an exit latency
limit for idle states to be specified (Daniel Lezcano)
- Fix cpufreq driver registration and clarify a comment in the
cpufreq core (Viresh Kumar)
- Add NULL checks to the show() and store() methods of sysfs
attributes exposed by cpufreq (Kai Shen)
- Update cpufreq drivers:
* Fix for a plain int as pointer warning from sparse in
intel_pstate (Jamal Shareef)
* Fix for a hardcoded number of CPUs and stack bloat in the
powernv driver (John Hubbard)
* Updates to the ti-cpufreq driver and DT files to support new
platforms and migrate bindings from opp-v1 to opp-v2 (Adam Ford,
H. Nikolaus Schaller)
* Merging of the arm_big_little and vexpress-spc drivers and
related cleanup (Sudeep Holla)
* Fix for imx's default speed grade value (Anson Huang)
* Minor cleanup of the s3c64xx driver (Nathan Chancellor)
* CPU speed bin detection fix for sun50i (Ondrej Jirman)
- Appoint Chanwoo Choi as the new devfreq maintainer.
- Update the devfreq core:
* Check NULL governor in available_governors_show sysfs to prevent
showing wrong governor information and fix a race condition
between devfreq_update_status() and trans_stat_show() (Leonard
Crestez)
* Add new 'interrupt-driven' flag for devfreq governors to allow
interrupt-driven governors to prevent the devfreq core from
polling devices for status (Dmitry Osipenko)
* Improve an error message in devfreq_add_device() (Matthias
Kaehlcke)
- Update devfreq drivers:
* tegra30 driver fixes and cleanups (Dmitry Osipenko)
* Removal of unused property from dt-binding documentation for the
exynos-bus driver (Kamil Konieczny)
* exynos-ppmu cleanup and DT bindings update (Lukasz Luba, Marek
Szyprowski)
- Add new CPU IDs for CometLake Mobile and Desktop to the Intel RAPL
power capping driver (Zhang Rui)
- Allow device initialization in the generic power domains (genpd)
framework to be more straightforward and clean it up (Ulf Hansson)
- Add support for adjusting OPP voltages at run time to the OPP
framework (Stephen Boyd)
- Avoid freeing memory that has never been allocated in the
hibernation core (Andy Whitcroft)
- Clean up function headers in a header file and coding style in the
wakeup IRQs handling code (Ulf Hansson, Xiaofei Tan)
- Clean up the SmartReflex adaptive voltage scaling (AVS) driver for
ARM (Ben Dooks, Geert Uytterhoeven)
- Wrap power management documentation to fit in 80 columns (Bjorn
Helgaas)
- Add pm-graph utility entry to MAINTAINERS (Todd Brandt)
- Update the cpupower utility:
* Fix the handling of set and info subcommands (Abhishek Goel)
* Fix build warnings (Nathan Chancellor)
* Improve mperf_monitor handling (Janakarajan Natarajan)"
* tag 'pm-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (83 commits)
PM: Wrap documentation to fit in 80 columns
cpuidle: Pass exit latency limit to cpuidle_use_deepest_state()
cpuidle: Allow idle injection to apply exit latency limit
cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks
cpuidle: teo: Avoid code duplication in conditionals
cpufreq: Register drivers only after CPU devices have been registered
cpuidle: teo: Avoid using "early hits" incorrectly
cpuidle: teo: Exclude cpuidle overhead from computations
PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
PM / Domains: Implement the ->start() callback for genpd
PM / Domains: Introduce dev_pm_domain_start()
ARM: OMAP2+: SmartReflex: add omap_sr_pdata definition
PM / wakeirq: remove unnecessary parentheses
power: avs: smartreflex: Remove superfluous cast in debugfs_create_file() call
cpuidle: Use nanoseconds as the unit of time
PM / OPP: Support adjusting OPP voltages at runtime
PM / core: Clean up some function headers in power.h
cpufreq: Add NULL checks to show() and store() methods of cpufreq
cpufreq: intel_pstate: Fix plain int as pointer warning from sparse
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
|
|
The DTC v1.5.1 added references to (U)INT32_MAX.
This is no problem for user-space programs since <stdint.h> defines
(U)INT32_MAX along with (u)int32_t.
For the kernel space, libfdt_env.h needs to be adjusted before we
pull in the changes.
In the kernel, we usually use s/u32 instead of (u)int32_t for the
fixed-width types.
Accordingly, we already have S/U32_MAX for their max values.
So, we should not add (U)INT32_MAX to <linux/limits.h> any more.
Instead, add them to the in-kernel libfdt_env.h to compile the
latest libfdt.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
msi.h is generic for all architectures except x86, which has its own
version. Enabling MSI by adding msi.h to every architecture's Kbuild is
just an additional step which doesn't need to be done.
Make msi.h mandatory in the asm-generic/Kbuild so we don't have to do it
for each architecture.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/r/c991669e29a79b1a8e28c3b4b3a125801a693de8.1571983829.git.michal.simek@xilinx.com
Tested-by: Paul Walmsley <paul.walmsley@sifive.com> # build only, rv32/rv64
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Waiman Long <longman@redhat.com>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # arch/riscv
|
|
This system call has been deprecated almost since it was introduced, and
in a survey of the linux distributions I can no longer find any of them
that enable CONFIG_SYSCTL_SYSCALL. The only indication that I can find
that anyone might care is that a few of the defconfigs in the kernel
enable CONFIG_SYSCTL_SYSCALL. However this appears in only 31 of 414
defconfigs in the kernel, so I suspect this symbols presence is simply
because it is harmless to include rather than because it is necessary.
As there appear to be no users of the sysctl system call, remove the
code. As this removes one of the few uses of the internal kernel mount
of proc I hope this allows for even more simplifications of the proc
filesystem.
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Anders Berg <anders.berg@lsi.com>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chee Nouk Phoon <cnphoon@altera.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Hua Yan <yanh@lemote.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Scott Telford <stelford@cadence.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- Cross-arch changes to move the linker sections for NOTES and
EXCEPTION_TABLE into the RO_DATA area, where they belong on most
architectures. (Kees Cook)
- Switch the x86 linker fill byte from x90 (NOP) to 0xcc (INT3), to
trap jumps into the middle of those padding areas instead of
sliding execution. (Kees Cook)
- A thorough cleanup of symbol definitions within x86 assembler code.
The rather randomly named macros got streamlined around a
(hopefully) straightforward naming scheme:
SYM_START(name, linkage, align...)
SYM_END(name, sym_type)
SYM_FUNC_START(name)
SYM_FUNC_END(name)
SYM_CODE_START(name)
SYM_CODE_END(name)
SYM_DATA_START(name)
SYM_DATA_END(name)
etc - with about three times of these basic primitives with some
label, local symbol or attribute variant, expressed via postfixes.
No change in functionality intended. (Jiri Slaby)
- Misc other changes, cleanups and smaller fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
x86/entry/64: Remove pointless jump in paranoid_exit
x86/entry/32: Remove unused resume_userspace label
x86/build/vdso: Remove meaningless CFLAGS_REMOVE_*.o
m68k: Convert missed RODATA to RO_DATA
x86/vmlinux: Use INT3 instead of NOP for linker fill bytes
x86/mm: Report actual image regions in /proc/iomem
x86/mm: Report which part of kernel image is freed
x86/mm: Remove redundant address-of operators on addresses
xtensa: Move EXCEPTION_TABLE to RO_DATA segment
powerpc: Move EXCEPTION_TABLE to RO_DATA segment
parisc: Move EXCEPTION_TABLE to RO_DATA segment
microblaze: Move EXCEPTION_TABLE to RO_DATA segment
ia64: Move EXCEPTION_TABLE to RO_DATA segment
h8300: Move EXCEPTION_TABLE to RO_DATA segment
c6x: Move EXCEPTION_TABLE to RO_DATA segment
arm64: Move EXCEPTION_TABLE to RO_DATA segment
alpha: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Actually use _etext for the end of the text segment
vmlinux.lds.h: Allow EXCEPTION_TABLE to live in RO_DATA
...
|
|
* pm-cpufreq: (23 commits)
cpufreq: Register drivers only after CPU devices have been registered
cpufreq: Add NULL checks to show() and store() methods of cpufreq
cpufreq: intel_pstate: Fix plain int as pointer warning from sparse
cpufreq: sun50i: Fix CPU speed bin detection
cpufreq: powernv: fix stack bloat and hard limit on number of CPUs
cpufreq: Clarify the comment in cpufreq_set_policy()
cpufreq: vexpress-spc: find and skip duplicates when merging frequencies
cpufreq: vexpress-spc: use macros instead of hardcoded values for cluster ids
cpufreq: s3c64xx: Remove pointless NULL check in s3c64xx_cpufreq_driver_init
cpufreq: imx-cpufreq-dt: Correct i.MX8MN's default speed grade value
cpufreq: vexpress-spc: fix some coding style issues
cpufreq: vexpress-spc: remove lots of debug messages
cpufreq: vexpress-spc: drop unnessary cpufreq_arm_bL_ops abstraction
cpufreq: merge arm_big_little and vexpress-spc
cpufreq: scpi: remove stale/outdated comment about the driver
ARM: dts: Add OPP-V2 table for AM3517
cpufreq: ti-cpufreq: Add support for AM3517
ARM: dts: omap36xx: using OPP1G needs to control the abb_ldo
cpufreq: ti-cpufreq: omap36xx use "cpu0","vbb" if run in multi_regulator mode
ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430 or ti,omap3630 or ti,am3517
...
|
|
* pm-cpuidle:
cpuidle: Pass exit latency limit to cpuidle_use_deepest_state()
cpuidle: Allow idle injection to apply exit latency limit
cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks
cpuidle: teo: Avoid code duplication in conditionals
cpuidle: teo: Avoid using "early hits" incorrectly
cpuidle: teo: Exclude cpuidle overhead from computations
cpuidle: Use nanoseconds as the unit of time
cpuidle: Consolidate disabled state checks
ACPI: processor_idle: Skip dummy wait if kernel is in guest
cpuidle: Do not unset the driver if it is there already
cpuidle: teo: Fix "early hits" handling for disabled idle states
cpuidle: teo: Consider hits and misses metrics of disabled states
cpuidle: teo: Rename local variable in teo_select()
cpuidle: teo: Ignore disabled idle states that are too deep
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Lots of stuff going on in the core for SPI this time around, the two
big changes both being around time in different forms:
- A rework of delay times from Alexandru Ardelean which makes the
ways in which they are specified more consistent between drivers so
that what's available to clients is less dependent on the hardware
implementation.
- Support for PTP timestamping of transfers from Vladimir Oltean,
useful for use with precision clocks with SPI control interfaces.
- Big cleanups for the Atmel, PXA2xx and Zynq QSPI drivers"
* tag 'spi-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: spi: Convert stm32 QSPI bindings to json-schema
spi: pic32: Retire dma_request_slave_channel_compat()
spi: Fix Kconfig indentation
spi: mediatek: add SPI_CS_HIGH support
spi: st-ssc4: add missed pm_runtime_disable
spi: tegra20-slink: add missed clk_unprepare
spi: tegra20-slink: Use dma_request_chan() directly for channel request
spi: tegra114: Use dma_request_chan() directly for channel request
spi: s3c64xx: Use dma_request_chan() directly for channel request
spi: qup: Use dma_request_chan() directly for channel request
spi: pl022: Use dma_request_chan() directly for channel request
spi: imx: Use dma_request_chan() directly for channel request
spi: fsl-lpspi: Use dma_request_chan() directly for channel request
spi: atmel: Use dma_request_chan() directly for channel request
spi: at91-usart: Use dma_request_chan() directly for channel request
spi: fsl-cpm: Correct the free:ing
spi: Fix regression to return zero on success instead of positive value
spi: pxa2xx: Add missed security checks
spi: nxp-fspi: Use devm API to fix missed unregistration of controller
spi: omap2-mcspi: Remove redundant checks
...
|
|
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
|
|
Pull crypto updates from Herbert Xu:
"API:
- Add library interfaces of certain crypto algorithms for WireGuard
- Remove the obsolete ablkcipher and blkcipher interfaces
- Move add_early_randomness() out of rng_mutex
Algorithms:
- Add blake2b shash algorithm
- Add blake2s shash algorithm
- Add curve25519 kpp algorithm
- Implement 4 way interleave in arm64/gcm-ce
- Implement ciphertext stealing in powerpc/spe-xts
- Add Eric Biggers's scalar accelerated ChaCha code for ARM
- Add accelerated 32r2 code from Zinc for MIPS
- Add OpenSSL/CRYPTOGRAMS poly1305 implementation for ARM and MIPS
Drivers:
- Fix entropy reading failures in ks-sa
- Add support for sam9x60 in atmel
- Add crypto accelerator for amlogic GXL
- Add sun8i-ce Crypto Engine
- Add sun8i-ss cryptographic offloader
- Add a host of algorithms to inside-secure
- Add NPCM RNG driver
- add HiSilicon HPRE accelerator
- Add HiSilicon TRNG driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (285 commits)
crypto: vmx - Avoid weird build failures
crypto: lib/chacha20poly1305 - use chacha20_crypt()
crypto: x86/chacha - only unregister algorithms if registered
crypto: chacha_generic - remove unnecessary setkey() functions
crypto: amlogic - enable working on big endian kernel
crypto: sun8i-ce - enable working on big endian
crypto: mips/chacha - select CRYPTO_SKCIPHER, not CRYPTO_BLKCIPHER
hwrng: ks-sa - Enable COMPILE_TEST
crypto: essiv - remove redundant null pointer check before kfree
crypto: atmel-aes - Change data type for "lastc" buffer
crypto: atmel-tdes - Set the IV after {en,de}crypt
crypto: sun4i-ss - fix big endian issues
crypto: sun4i-ss - hide the Invalid keylen message
crypto: sun4i-ss - use crypto_ahash_digestsize
crypto: sun4i-ss - remove dependency on not 64BIT
crypto: sun4i-ss - Fix 64-bit size_t warnings on sun4i-ss-hash.c
MAINTAINERS: Add maintainer for HiSilicon SEC V2 driver
crypto: hisilicon - add DebugFS for HiSilicon SEC
Documentation: add DebugFS doc for HiSilicon SEC
crypto: hisilicon - add SRIOV for HiSilicon SEC
...
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- data abort report and injection
- steal time support
- GICv4 performance improvements
- vgic ITS emulation fixes
- simplify FWB handling
- enable halt polling counters
- make the emulated timer PREEMPT_RT compliant
s390:
- small fixes and cleanups
- selftest improvements
- yield improvements
PPC:
- add capability to tell userspace whether we can single-step the
guest
- improve the allocation of XIVE virtual processor IDs
- rewrite interrupt synthesis code to deliver interrupts in virtual
mode when appropriate.
- minor cleanups and improvements.
x86:
- XSAVES support for AMD
- more accurate report of nested guest TSC to the nested hypervisor
- retpoline optimizations
- support for nested 5-level page tables
- PMU virtualization optimizations, and improved support for nested
PMU virtualization
- correct latching of INITs for nested virtualization
- IOAPIC optimization
- TSX_CTRL virtualization for more TAA happiness
- improved allocation and flushing of SEV ASIDs
- many bugfixes and cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
kvm: nVMX: Relax guest IA32_FEATURE_CONTROL constraints
KVM: x86: Grab KVM's srcu lock when setting nested state
KVM: x86: Open code shared_msr_update() in its only caller
KVM: Fix jump label out_free_* in kvm_init()
KVM: x86: Remove a spurious export of a static function
KVM: x86: create mmu/ subdirectory
KVM: nVMX: Remove unnecessary TLB flushes on L1<->L2 switches when L1 use apic-access-page
KVM: x86: remove set but not used variable 'called'
KVM: nVMX: Do not mark vmcs02->apic_access_page as dirty when unpinning
KVM: vmx: use MSR_IA32_TSX_CTRL to hard-disable TSX on guest that lack it
KVM: vmx: implement MSR_IA32_TSX_CTRL disable RTM functionality
KVM: x86: implement MSR_IA32_TSX_CTRL effect on CPUID
KVM: x86: do not modify masked bits of shared MSRs
KVM: x86: fix presentation of TSX feature in ARCH_CAPABILITIES
KVM: PPC: Book3S HV: XIVE: Fix potential page leak on error path
KVM: PPC: Book3S HV: XIVE: Free previous EQ page when setting up a new one
KVM: nVMX: Assume TLB entries of L1 and L2 are tagged differently if L0 use EPT
KVM: x86: Unexport kvm_vcpu_reload_apic_access_page()
KVM: nVMX: add CR4_LA57 bit to nested CR4_FIXED1
KVM: nVMX: Use semi-colon instead of comma for exit-handlers initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- a small series to remove the build constraint of Xen x86 MCE handling
to 64-bit only
- a bunch of minor cleanups
* tag 'for-linus-5.5a-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix Kconfig indentation
xen/mcelog: also allow building for 32-bit kernels
xen/mcelog: add PPIN to record when available
xen/mcelog: drop __MC_MSR_MCGCAP
xen/gntdev: Use select for DMA_SHARED_BUFFER
xen: mm: make xen_mm_init static
xen: mm: include <xen/xen-ops.h> for missing declarations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the arm64-specific bits (core arch and perf, new arm64
selftests), it touches the generic cow_user_page() (reviewed by
Kirill) together with a macro for x86 to preserve the existing
behaviour on this architecture.
Summary:
- On ARMv8 CPUs without hardware updates of the access flag, avoid
failing cow_user_page() on PFN mappings if the pte is old. The
patches introduce an arch_faults_on_old_pte() macro, defined as
false on x86. When true, cow_user_page() makes the pte young before
attempting __copy_from_user_inatomic().
- Covert the synchronous exception handling paths in
arch/arm64/kernel/entry.S to C.
- FTRACE_WITH_REGS support for arm64.
- ZONE_DMA re-introduced on arm64 to support Raspberry Pi 4
- Several kselftest cases specific to arm64, together with a
MAINTAINERS update for these files (moved to the ARM64 PORT entry).
- Workaround for a Neoverse-N1 erratum where the CPU may fetch stale
instructions under certain conditions.
- Workaround for Cortex-A57 and A72 errata where the CPU may
speculatively execute an AT instruction and associate a VMID with
the wrong guest page tables (corrupting the TLB).
- Perf updates for arm64: additional PMU topologies on HiSilicon
platforms, support for CCN-512 interconnect, AXI ID filtering in
the IMX8 DDR PMU, support for the CCPI2 uncore PMU in ThunderX2.
- GICv3 optimisation to avoid a heavy barrier when accessing the
ICC_PMR_EL1 register.
- ELF HWCAP documentation updates and clean-up.
- SMC calling convention conduit code clean-up.
- KASLR diagnostics printed during boot
- NVIDIA Carmel CPU added to the KPTI whitelist
- Some arm64 mm clean-ups: use generic free_initrd_mem(), remove
stale macro, simplify calculation in __create_pgd_mapping(), typos.
- Kconfig clean-ups: CMDLINE_FORCE to depend on CMDLINE, choice for
endinanness to help with allmodconfig"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (93 commits)
arm64: Kconfig: add a choice for endianness
kselftest: arm64: fix spelling mistake "contiguos" -> "contiguous"
arm64: Kconfig: make CMDLINE_FORCE depend on CMDLINE
MAINTAINERS: Add arm64 selftests to the ARM64 PORT entry
arm64: kaslr: Check command line before looking for a seed
arm64: kaslr: Announce KASLR status on boot
kselftest: arm64: fake_sigreturn_misaligned_sp
kselftest: arm64: fake_sigreturn_bad_size
kselftest: arm64: fake_sigreturn_duplicated_fpsimd
kselftest: arm64: fake_sigreturn_missing_fpsimd
kselftest: arm64: fake_sigreturn_bad_size_for_magic0
kselftest: arm64: fake_sigreturn_bad_magic
kselftest: arm64: add helper get_current_context
kselftest: arm64: extend test_init functionalities
kselftest: arm64: mangle_pstate_invalid_mode_el[123][ht]
kselftest: arm64: mangle_pstate_invalid_daif_bits
kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils
kselftest: arm64: extend toplevel skeleton Makefile
drivers/perf: hisi: update the sccl_id/ccl_id for certain HiSilicon platform
arm64: mm: reserve CMA and crashkernel in ZONE_DMA32
...
|
|
The generic implementation of refcount_t should be good enough for
everybody, so remove ARCH_HAS_REFCOUNT and REFCOUNT_FULL entirely,
leaving the generic implementation enabled unconditionally.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191121115902.2551-9-will@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
|
|
Commit d3c61619568c ("ARM: 8788/1: ftrace: remove old mcount support")
removed the old mcount support, but forget to remove these three
declarations. This patch removes them.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since $(NM) variable can be easily overridden for the whole build, it's
better to use it instead of $(CROSS_COMPILE)nm. The use of $(CROSS_COMPILE)
prefixed variables where their calculated equivalents can be used is
incorrect. This fixes issues with builds where $(NM) is set to llvm-nm.
Link: https://github.com/ClangBuiltLinux/linux/issues/766
Signed-off-by: Dmitry Golovin <dima@golovin.in>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Matthias Maennich <maennich@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Conflicts:
arch/x86/kvm/vmx/vmx.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for Linux 5.5:
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
Conflicts:
include/uapi/linux/kvm.h
|
|
Currently each architectures that wants to override dma_to_phys and
phys_to_dma also has to provide dma_capable. But there isn't really
any good reason for that. powerpc and mips just have copies of the
generic one minus the latests fix, and the arm one was the inspiration
for said fix, but misses the bus_dma_mask handling.
Make all architectures use the generic version instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
|
|
These are pure cache maintainance routines, so drop the unused
struct device argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add CONFIG_TI_CPSW_SWITCHDEV option to enable new cpsw switchdev driver
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to
enable testing of the new solution.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DT nodes for new cpsw switch dev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
- Various cleanups
|
|
Commit 99e98d3fb100 ("cpuidle: Consolidate disabled state checks")
overlooked the fact that the imx6q and tegra20 cpuidle drivers use
the "disabled" field in struct cpuidle_state for quirks which trigger
after the initialization of cpuidle, so reading the initial value of
that field is not sufficient for those drivers.
In order to allow them to implement the quirks without using the
"disabled" field in struct cpuidle_state, introduce a new helper
function and modify them to use it.
Fixes: 99e98d3fb100 ("cpuidle: Consolidate disabled state checks")
Reported-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Lots of overlapping changes and parallel additions, stuff
like that.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This ports the SUPERCOP implementation for usage in kernel space. In
addition to the usual header, macro, and style changes required for
kernel space, it makes a few small changes to the code:
- The stack alignment is relaxed to 16 bytes.
- Superfluous mov statements have been removed.
- ldr for constants has been replaced with movw.
- ldreq has been replaced with moveq.
- The str epilogue has been made more idiomatic.
- SIMD registers are not pushed and popped at the beginning and end.
- The prologue and epilogue have been made idiomatic.
- A hole has been removed from the stack, saving 32 bytes.
- We write-back the base register whenever possible for vld1.8.
- Some multiplications have been reordered for better A7 performance.
There are more opportunities for cleanup, since this code is from qhasm,
which doesn't always do the most opportune thing. But even prior to
extensive hand optimizations, this code delivers significant performance
improvements (given in get_cycles() per call):
----------- -------------
| generic C | this commit |
------------ ----------- -------------
| Cortex-A7 | 49136 | 22395 |
------------ ----------- -------------
| Cortex-A17 | 17326 | 4983 |
------------ ----------- -------------
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[ardb: - move to arch/arm/crypto
- wire into lib/crypto framework
- implement crypto API KPP hooks ]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
implementation
This comes from Dan Bernstein and Peter Schwabe's public domain NEON
code, and is included here in raw form so that subsequent commits that
fix these up for the kernel can see how it has changed. This code does
have some entirely cosmetic formatting differences, adding indentation
and so forth, so that when we actually port it for use in the kernel in
the subsequent commit, it's obvious what's changed in the process.
This code originates from SUPERCOP 20180818, available at
<https://bench.cr.yp.to/supercop.html>.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
