| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.19
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
arm64: dts: qcom: sc7280: eDP for herobrine boards
arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
arm64: dts: qcom: sm8350-duo2: enable battery charger
arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
arm64: dts: qcom: pm8350c: Add pwm support
arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7180: Remove ipa interconnect node
arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
arm64: dts: qcom: sc7280: Add GPI DMAengines
arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
arm64: dts: qcom: db845c: Add support for MCP2517FD
arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
arm64: dts: qcom: sm8250: camss: Add CCI definitions
...
Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/dt
TI K3 device tree updates for v5.19
New Features:
J721e:
* Enable DSS, DP, HDMI on J721e EVM and SK
AM62:
* MCAN, MCU GPIO, ECAP APWM, DMA, Etherent and several peripheral on AM62 SK EVM
AM64:
* Enable Wireless LAN support
Fixes:
Drop incorrect MCU UART clock rates
* tag 'ti-k3-dt-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: dts: ti: k3-j721e-sk: Enable HDMI
arm64: dts: ti: k3-j721e-sk: Enable DisplayPort
arm64: dts: ti: k3-j721e-common-proc-board: add DP to j7 evm
arm64: dts: ti: k3-j721e-*: add DP & DP PHY
arm64: dts: ti: k3-am62: Add SA3UL ranges in cbass_main
arm64: dts: ti: k3-am62: Add support for MCAN
arm64: dts: ti: k3-am62-mcu: Enable MCU GPIO module
arm64: dts: ti: k3-am625-sk: Add ECAP APWM nodes
arm64: dts: ti: k3-am625-sk: Enable on board peripherals
arm64: dts: ti: k3-am62: Add more peripheral nodes
arm64: dts: ti: k3-am642-sk: Enable WLAN connected to SDHCI0
arm64: dts: ti: k3-am64-mcu: remove incorrect UART base clock rates
Link: https://lore.kernel.org/r/3dc2011b-eb6d-dcd5-3921-57f6a1cf6d8e@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
- F1C100 improvements (SPI, MMC, timer, cpu, watchdog)
- SPI flash node for licheepi-nano
- enabled analogue audio on olinuxino-a64
- GPIO port regulators on teres-i
* tag 'sunxi-dt-for-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: teres-i: Add GPIO port regulators
arm64: dts: allwinner: a64: olinuxino: Enable audio
ARM: dts: suniv: licheepi-nano: add SPI flash
ARM: dts: suniv: F1C100: add SPI support
dt-bindings: spi: sunxi: document F1C100 controllers
ARM: dts: suniv: licheepi-nano: add microSD card
ARM: dts: suniv: F1C100: add MMC controllers
ARM: dts: suniv: F1C100: fix timer node
ARM: dts: suniv: F1C100: fix CPU node
ARM: dts: suniv: F1C100: add clock and reset macros
dt-bindings: arm: sunxi: document LicheePi Nano name
ARM: dts: suniv: F1C100: fix watchdog compatible
dt-bindings: watchdog: sunxi: clarify clock support
dt-bindings: watchdog: sunxi: fix F1C100s compatible
Link: https://lore.kernel.org/r/YnVUmSLE1MZFkApt@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.19-rc1
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
* tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add missing DFLL reset on Tegra210
arm64: tegra: Add memory controller channels
arm64: tegra: Enable ASRC on various platforms
arm64: tegra: Add ASRC device on Tegra186 and later
arm64: tegra: Update PWM fan node name
arm64: tegra: Add node for Tegra234 CCPLEX cluster
arm64: tegra: Add QSPI controllers on Tegra234
arm64: tegra: Update SDMMC1/3 clock source for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19 (take two)
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits)
arm64: dts: renesas: Add initial device tree for RZ/V2M EVK
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Describe the RTC
arm64: dts: renesas: Add interrupt-names to CANFD nodes
arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
arm64: dts: renesas: r9a07g043: Add TSU node
arm64: dts: renesas: r9a07g043: Add OPP table
arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes
arm64: dts: renesas: r9a07g054: Fix external clk node names
arm64: dts: renesas: r9a07g044: Fix external clk node names
ARM: dts: r9a06g032: Fix the NAND controller node
ARM: dts: r9a06g032: Fill the UART DMA properties
ARM: dts: r9a06g032: Describe the DMA router
ARM: dts: r9a06g032: Add the two DMA nodes
arm64: dts: renesas: Remove empty rgb output endpoints
...
Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.19, part two
1. Cleanups: unused and undocumented dma-channels and dma-requests.
2. Add clock controllers to ExynosAutov9.
* tag 'samsung-dt64-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: switch UFS clock node in ExynosAutov9
arm64: dts: exynos: switch USI clocks in ExynosAutov9
arm64: dts: exynos: add initial CMU clock nodes in ExynosAutov9
dt-bindings: clock: add Exynos Auto v9 SoC CMU bindings
dt-bindings: clock: add clock binding definitions for Exynos Auto v9
arm64: dts: fsd: drop useless 'dma-channels/requests' properties
arm64: dts: exynos: drop useless 'dma-channels/requests' properties
arm64: dts: exynos: move XTCXO clock frequency to board in Exynos Auto v9
Link: https://lore.kernel.org/r/20220506081438.149192-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Minor cleanup of ARM64 DTS for v5.19
Align SPI NOR node names and freq-table-hz to DT schema. Drop
unused/undocumented dma-channels/dma-requests.
* tag 'dt64-cleanup-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: broadcom: drop useless 'dma-channels/requests' properties
arm64: dts: stratix10/agilex: drop useless 'dma-channels/requests' properties
arm64: dts: marvell: align SPI NOR node name with dtschema
arm64: dts: microchip: align SPI NOR node name with dtschema
arm64: dts: hisilicon: align 'freq-table-hz' with dtschema in UFS
Link: https://lore.kernel.org/r/20220506081438.149192-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add basic support for RZ/V2M EVK (based on R9A09G011):
- memory
- External input clock
- UART
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-13-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Details of the SoC can be found here:
https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-cortex-a-mpus/rzv2m-dual-cortex-a53-lpddr4x32bit-ai-accelerator-isp-4k-video-codec-4k-camera-input-fhd-display-output
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220504094456.24386-3-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence update the compatible properties in various device nodes
to include family-specific compatible values for R-Car Gen4 instead of
R-Car Gen3:
- DMAC,
- (H)SCIF,
- I2C,
- IPMMU,
- WDT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/73cea9d5e1a6639422c67e4df4285042e31c9fd5.1651497071.git.geert+renesas@glider.be
|
|
The Renesas R-Car CAN-FD Controller on R-Car Gen3 and RZ/G2 SoCs has two
interrupts. Add interrupt-names properties to all CAN-FD device nodes
to identify the individual interrupts, so we can make this property a
required property in the DT bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/10eef1e20372af4a156b06df8e5124666ec7c6b6.1651512451.git.geert+renesas@glider.be
|
|
Add SPI Multi I/O Bus controller node to R9A07G043 (RZ/G2UL) SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220502190155.84496-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
Based on the work done by Dien Pham <dien.pham.ry@renesas.com>
and others for r8a77990 SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220501112926.47024-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add TSU node to RZ/G2UL SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220501112926.47024-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add OPP table for RZ/G2UL SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220501112926.47024-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add RSPI{0,1,2} nodes to R9A07G043 (RZ/G2UL) SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220501112926.47024-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add suffix '-clk' for can and extal clk node names and replace the
clk node names audio_clk{1,2} with audio{1,2}-clk as per the device
tree specification.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220428133156.18080-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add suffix '-clk' for can and extal clk node names and replace the
clk node names audio_clk{1,2} with audio{1,2}-clk as per the device
tree specification.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220428133156.18080-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty rgb output endpoints
from SoC dtsi files, and declare them in the board dts instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-2-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty lvds endpoints from
SoC dtsi files, they should be instead declared in the board dts or in
overlays.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220424161228.8147-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable USB2.0 Host/Device support on RZ/G2UL SMARC EVK by
adding usb{0,1} pincontrol entries to the soc-pinctrl dtsi
and deleting the nodes which disabled it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220429072400.23729-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable Audio on RZ/G2UL SMARC EVK by adding ssi1 pincontrol entries
to the soc-pinctrl dtsi and ssi1 and cpu sound_dai nodes to the board
dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220429072400.23729-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
common dtsi
On RZ/G2{L,LC} SoM module, the wm8978 audio codec is connected to ssi0,
whereas on RZ/G2UL it is connected to ssi1. So move ssi0 and cpu
sound_dai nodes from common dtsi to board specific dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220429072400.23729-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Initial support for the Renesas White Hawk CPU and BreakOut boards.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220428135058.597586-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add initial support for the Renesas R8A779G0 (R-Car V4H) SoC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220428135058.597586-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The SoC is always present on sc7180-trogdor.dtsi and thus we should
include it in the "generic" dtsi file for trogdor. Previously we had
removed it from there because we had to do the spi6/spi0 swizzle, so
each trogdor variant board had to include sc7180.dtsi and then
sc7180-trogdor.dtsi so that the latter dtsi file could modify the right
spi bus for EC and H1 properties that are common to all trogdor boards.
Now that we're done with that we can replace sc7180.dtsi includes with
sc7180-trogdor.dtsi and include sc7180.dtsi in sc7180-trogdor.dtsi as
was originally intended. We still need to include sc7180-trogdor.dtsi
before the bridge dtsi files though because those rely on the panel
label.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-4-swboyd@chromium.org
|
|
We had to do this spi0/spi6 flip-flop on trogdor-r0 because the spi
buses got swizzled between r0 and r1. The swizzle stopped after r1, but
we kept this around to support either hardware possibility and to keep
trogdor-r0 working.
trogdor-r0 isn't supported upstream, so this swizzle is not doing
anything besides making a pattern that others tryt to copy for the EC and
H1 nodes. Let's remove it and simplify the dts files.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-3-swboyd@chromium.org
|
|
Trogdor boards with a detachable keyboard don't have a trackpad over
i2c. Instead the trackpad is on the detachable keyboard base. Let's move
the enabling of the trackpad i2c bus out of the base sc7180-trogdor.dtsi
file so that each trogdor board that is detachable, of which there are
many, doesn't have to disable the trackpad bus.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-2-swboyd@chromium.org
|
|
Add eDP support to herobrine boards, splitting up amongst the
different files as makes sense. Rationale for the current split of
things:
* The eDP connector itself is on qcard. However, not all devices with
a qcard will use an eDP panel. Some might use MIPI and, presumably,
someone could build a device with qcard that had no display at all.
* The qcard provides a PWM for backlight that goes to the eDP
connector. This PWM is also provided to the board and it's expected
that it would be used as the backlight PWM even for herobrine
devices with MIPI displays.
* It's currently assumed that all herobrine boards will have some sort
of display, either MIPI or eDP (but not both).
* We will assume herobrine-rev1 has eDP. The schematics allow for a
MIPI panel to be hooked up but, aside from some testing, nobody is
doing this and most boards don't have all the parts stuffed for
it. The two panels would also share a PWM for backlight, which is
weird.
* herobrine-villager and herobrine-hoglin (crd) also have eDP.
* herobrine-hoglin (crd) has slightly different regulator setup for
the backlight. It's expected that this is unique to this board. See
comments in the dts file.
* There are some regulators that are defined in the qcard schematic
but provided by the board like "vreg_edp_bl" and
"vreg_edp_3p3". While we could put references to these regulators
straight in the qcard.dtsi file, this would force someone using
qcard that didn't provide those regulators to provide a dummy or do
an ugly /delete-node/. Instead, we'll add references in
herobrine.dtsi.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220426124053.v2.1.Iedd71976a78d53c301ce0134832de95a989c9195@changeid
|
|
Fix the issues seen with ethernet traffic getting stalled on SA8155p-ADP
board with default (or larger) mtu size of 1500 bytes, by disabling
multiple Tx and Rx queues for the stmmac IP block.
With the single queue setup, the ethernet traffic is stable,
wget / curl can work well on the board and no ethernet stall is
observed even when longer netperf / iperf3 test are run. Also
a performance of ~940 Mbits/sec is observed on the 1G link, so
there is no observable degradation in performance as well.
Fixes: c5cb42cc8411 ("arm64: dts: qcom: sa8155p-adp: Enable ethernet node")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423195003.353150-1-bhupesh.sharma@linaro.org
|
|
Fix the IOMMU sid value for SDC2 controller, to ensure that no
ADMA error is observed when the microSD card is detected on the
SA8155p-ADP board.
Fixes: 876644c76034 ("arm64: dts: qcom: sm8150: Add support for SDC2")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422210611.173842-1-bhupesh.sharma@linaro.org
|
|
https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs changes for 5.19,
please pull the following:
- Krzysztof fixes the SPI NOR Device Tree node name to comply with the
dtschema
* tag 'arm-soc/for-5.19/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220504210942.1838248-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add node for dvi bridge and the endpoint nodes to
describe connection from
DSS => TI TFP410 DPI-to-DVI Bridge => HDMI connector.
Also add the required pinmux for HDMI hotplug and
powerdown
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220505090709.9252-3-r-ravikumar@ti.com
|
|
Add the endpoint nodes to describe connection from
DSS => MHDP => DisplayPort connector.
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220505090709.9252-2-r-ravikumar@ti.com
|
|
Add the endpoint nodes to describe connection from
DSS => MHDP => DisplayPort connector.
Also add the required pinmux nodes for hotplug.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220429112639.13004-3-r-ravikumar@ti.com
|
|
Add DT nodes for DisplayPort and DisplayPort PHY. The DP is Cadence MHDP
8546 and the PHY is a Cadence Torrent PHY with TI WIZ wrapper.
Also add the required phy link nodes in the board dts files.
A slight irregularity in the bindings is the DPTX PHY register block,
which is in the MHDP IP, but is needed and mapped by the PHY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220429112639.13004-2-r-ravikumar@ti.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
Arm FVP/Juno device tree updates for v5.19
The main and bulk of the change is the addition of new platform
Arm corstone1000(both FVP and FPGA versions). Also, there are
addition of Coresight Cross Trigger Interface(CTI) support on Juno,
fix for incorrect SCMI power domain IDs, addition of virtio-rng
on FVP which is default disabled as it works only on latest versions
of the FVP model.
Other miscellanous changes include dropping of useless
'dma-channels/requests' properties and updating virtio device
node names as per dtschema.
* tag 'juno-updates-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Drop useless 'dma-channels/requests' properties
arm64: dts: fvp: Align virtio device node names with dtschema
arm64: dts: fvp: Add virtio-rng support
arm64: dts: Add Arm corstone1000 platform support
dt-bindings: Add Arm corstone1000 platform
arm64: dts: juno: add CTI entries to device tree
arm64: dts: juno: Fix SCMI power domain IDs for ETF and CS funnel
Link: https://lore.kernel.org/r/20220504112917.3492009-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use cmu_fsys's clock node instead of dummy UFS clock node.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20220504075154.58819-13-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Use CMU clock nodes instead of dummy fixed-rate-clock.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20220504075154.58819-12-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Add cmu_top, cmu_busmc, cmu_core, cmu_fsys and peric0/c1/s clock nodes.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20220504075154.58819-11-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Enable the relevant qup and I2C nodes to enable the battery charger.
Signed-off-by: Katherine Perez <kaperez@linux.microsoft.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211207231736.1762503-2-kaperez@linux.microsoft.com
|
|
Enable pm8350c pmic pwm support for backlight on sc7280-idp2.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1645509309-16142-5-git-send-email-quic_c_skakit@quicinc.com
|
|
Add pwm support for PM8350C pmic.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1645509309-16142-4-git-send-email-quic_c_skakit@quicinc.com
|
|
Commit 4782c0a5dd88 ("clk: tegra: Don't deassert reset on enabling
clocks") removed deassertion of reset lines when enabling peripheral
clocks. This breaks the initialization of the DFLL driver which relied
on this behaviour.
In order to be able to fix this, add the corresponding reset to the DT.
Tested on Google Pixel C.
Cc: stable@vger.kernel.org
Fixes: 4782c0a5dd88 ("clk: tegra: Don't deassert reset on enabling clocks")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-6-krzysztof.kozlowski@linaro.org
|
|
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-4-krzysztof.kozlowski@linaro.org
|
|
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-10-krzysztof.kozlowski@linaro.org
|
|
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-9-krzysztof.kozlowski@linaro.org
|
|
The external oscillator - XTCXO - is an input to the SoC. It is defined
in the Exynos Auto v9 SoC DTSI, because all boards will provide it and
clock controller bindings expect it, however the actual frequency of the
clock should be determined by the board.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220503092631.174713-1-krzysztof.kozlowski@linaro.org
|
|
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-3-git-send-email-quic_vnivarth@quicinc.com
|
