| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Lots of easy overlapping changes in the confict
resolutions here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
If userspace faults on a kernel address, handing them the raw ESR
value on the sigframe as part of the delivered signal can leak data
useful to attackers who are using information about the underlying hardware
fault type (e.g. translation vs permission) as a mechanism to defeat KASLR.
However there are also legitimate uses for the information provided
in the ESR -- notably the GCC and LLVM sanitizers use this to report
whether wild pointer accesses by the application are reads or writes
(since a wild write is a more serious bug than a wild read), so we
don't want to drop the ESR information entirely.
For faulting addresses in the kernel, sanitize the ESR. We choose
to present userspace with the illusion that there is nothing mapped
in the kernel's part of the address space at all, by reporting all
faults as level 0 translation faults taken to EL1.
These fields are safe to pass through to userspace as they depend
only on the instruction that userspace used to provoke the fault:
EC IL (always)
ISV CM WNR (for all data aborts)
All the other fields in ESR except DFSC are architecturally RES0
for an L0 translation fault taken to EL1, so can be zeroed out
without confusing userspace.
The illusion is not entirely perfect, as there is a tiny wrinkle
where we will report an alignment fault that was not due to the memory
type (for instance a LDREX to an unaligned address) as a translation
fault, whereas if you do this on real unmapped memory the alignment
fault takes precedence. This is not likely to trip anybody up in
practice, as the only users we know of for the ESR information who
care about the behaviour for kernel addresses only really want to
know about the WnR bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise modules that use these arithmetic operations will fail to
link. We accomplish this with the usual EXPORT_SYMBOL, which on most
architectures goes in the .S file but the ARM64 maintainers prefer that
insead it goes into arm64ksyms.
While we're at it, we also fix this up to use SPDX, and I personally
choose to relicense this as GPL2||BSD so that these symbols don't need
to be export_symbol_gpl, so all modules can use the routines, since
these are important general purpose compiler-generated function calls.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reported-by: PaX Team <pageexec@freemail.hu>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
For LSE atomics that read and write a register operand, we need to
ensure that these operands are annotated as "early clobber" if the
register is written before all of the input operands have been consumed.
Failure to do so can result in the compiler allocating the same register
to both operands, leading to splats such as:
Unable to handle kernel paging request at virtual address 11111122222221
[...]
x1 : 1111111122222222 x0 : 1111111122222221
Process swapper/0 (pid: 1, stack limit = 0x000000008209f908)
Call trace:
test_atomic64+0x1360/0x155c
where x0 has been allocated as both the value to be stored and also the
atomic_t pointer.
This patch adds the missing clobbers.
Cc: <stable@vger.kernel.org>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes. I've been queuing them up a bit too long so the
list is longer than it otherwise would have been spread out across a
few -rcs.
In general, it's a scattering of fixes across several platforms,
nothing truly serious enough to point out.
There's a slightly larger batch of them for the Davinci platforms due
to work to bring them back to life after some time, so there's a
handful of regressions, some of them going back very far, others more
recent.
There's also a few patches fixing DT on Renesas platforms since they
changed some bindings without remaining backwards compatible,
splitting up describing LVDS as a proper bridge instead of having it
as part of the display unit.
We could push for them to be backwards compatible with old device
trees, but it's likely to regress eventually if nobody's actually
using said compatibility"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: davinci: board-dm646x-evm: set VPIF capture card name
ARM: davinci: board-dm646x-evm: pass correct I2C adapter id for VPIF
ARM: davinci: dm646x: fix timer interrupt generation
ARM: keystone: fix platform_domain_notifier array overrun
arm64: dts: exynos: Fix interrupt type for I2S1 device on Exynos5433
ARM: dts: imx51-zii-rdu1: fix touchscreen bindings
firmware: arm_scmi: Use after free in scmi_create_protocol_device()
ARM: dts: cygnus: fix irq type for arm global timer
Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
tee: check shm references are consistent in offset/size
tee: shm: fix use-after-free via temporarily dropped reference
ARM: dts: imx7s: Pass the 'fsl,sec-era' property
ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
ARM: dts: correct missing "compatible" entry for ti81xx SoCs
ARM: OMAP1: ams-delta: fix deferred_fiq handler
arm64: tegra: Make BCM89610 PHY interrupt as active low
ARM: davinci: fix GPIO lookup for I2C
ARM: dts: logicpd-som-lv: Fix pinmux controller references
ARM: dts: logicpd-som-lv: Fix Audio Mute
ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
arm64: tegra: Device tree fixes for v4.17
This contains a one-line update to the device tree of the Tegra186 P3310
processor module, fixing the polarity of the PHY interrupt. Originally,
this was queued to go into v4.18, but the PHY ID matching patch has now
found its way into v4.17-rc5, which means that the PHY driver will know
how to identify the PHY on this board and try to use the interrupt. This
will unfortunately cause networking to break on P3310, hence why I think
this should go into v4.17.
* tag 'tegra-for-4.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Make BCM89610 PHY interrupt as active low
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add a new serial node for the Qualcomm BT controller QCA6174. This
allows automatic probing and hci registration through the serdev
framework instead of relying on the userspace helpers.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch enables regulators and gpios for the Qualcomm QCA6174 BT/WLAN
combo controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pull kvm fixes from Paolo Bonzini:
- ARM/ARM64 locking fixes
- x86 fixes: PCID, UMIP, locking
- improved support for recent Windows version that have a 2048 Hz APIC
timer
- rename KVM_HINTS_DEDICATED CPUID bit to KVM_HINTS_REALTIME
- better behaved selftests
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: rename KVM_HINTS_DEDICATED to KVM_HINTS_REALTIME
KVM: arm/arm64: VGIC/ITS save/restore: protect kvm_read_guest() calls
KVM: arm/arm64: VGIC/ITS: protect kvm_read_guest() calls with SRCU lock
KVM: arm/arm64: VGIC/ITS: Promote irq_lock() in update_affinity
KVM: arm/arm64: Properly protect VGIC locks from IRQs
KVM: X86: Lower the default timer frequency limit to 200us
KVM: vmx: update sec exec controls for UMIP iff emulating UMIP
kvm: x86: Suppress CR3_PCID_INVD bit only when PCIDs are enabled
KVM: selftests: exit with 0 status code when tests cannot be run
KVM: hyperv: idr_find needs RCU protection
x86: Delay skip of emulated hypercall instruction
KVM: Extend MAX_IRQ_ROUTES to 4096 for all archs
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kvm_read_guest() will eventually look up in kvm_memslots(), which requires
either to hold the kvm->slots_lock or to be inside a kvm->srcu critical
section.
In contrast to x86 and s390 we don't take the SRCU lock on every guest
exit, so we have to do it individually for each kvm_read_guest() call.
Provide a wrapper which does that and use that everywhere.
Note that ending the SRCU critical section before returning from the
kvm_read_guest() wrapper is safe, because the data has been *copied*, so
we don't need to rely on valid references to the memslot anymore.
Cc: Stable <stable@vger.kernel.org> # 4.8+
Reported-by: Jan Glauber <jan.glauber@caviumnetworks.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We can trivially save 4 bytes in prologue for cBPF since tail calls
can never be used from there. The register push/pop is pairwise,
here, x25 (fp) and x26 (tcc), so no point in changing that, only
reset to zero is not needed.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Improve the JIT to emit 64 and 32 bit immediates, the current
algorithm is not optimal and we often emit more instructions
than actually needed. arm64 has movz, movn, movk variants but
for the current 64 bit immediates we only use movz with a
series of movk when needed.
For example loading ffffffffffffabab emits the following 4
instructions in the JIT today:
* movz: abab, shift: 0, result: 000000000000abab
* movk: ffff, shift: 16, result: 00000000ffffabab
* movk: ffff, shift: 32, result: 0000ffffffffabab
* movk: ffff, shift: 48, result: ffffffffffffabab
Whereas after the patch the same load only needs a single
instruction:
* movn: 5454, shift: 0, result: ffffffffffffabab
Another example where two extra instructions can be saved:
* movz: abab, shift: 0, result: 000000000000abab
* movk: 1f2f, shift: 16, result: 000000001f2fabab
* movk: ffff, shift: 32, result: 0000ffff1f2fabab
* movk: ffff, shift: 48, result: ffffffff1f2fabab
After the patch:
* movn: e0d0, shift: 16, result: ffffffff1f2fffff
* movk: abab, shift: 0, result: ffffffff1f2fabab
Another example with movz, before:
* movz: 0000, shift: 0, result: 0000000000000000
* movk: fea0, shift: 32, result: 0000fea000000000
After:
* movz: fea0, shift: 32, result: 0000fea000000000
Moreover, reuse emit_a64_mov_i() for 32 bit immediates that
are loaded via emit_a64_mov_i64() which is a similar optimization
as done in 6fe8b9c1f41d ("bpf, x64: save several bytes by using
mov over movabsq when possible"). On arm64, the latter allows to
use a single instruction with movn due to zero extension where
otherwise two would be needed. And last but not least add a
missing optimization in emit_a64_mov_i() where movn is used but
the subsequent movk not needed. With some of the Cilium programs
in use, this shrinks the needed instructions by about three
percent. Tested on Cavium ThunderX CN8890.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Follow-up to 816d9ef32a8b ("bpf, arm64: remove ld_abs/ld_ind") in
that the extra 4 byte JIT scratchpad is not needed anymore since it
was in ld_abs/ld_ind as stack buffer for bpf_load_pointer().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
mvebu fixes for 4.17 (part 1)
Declare missing clocks needed for network on Armada 8040 base boards
(such as the McBin)
* tag 'mvebu-fixes-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Add mg_core_clk for ethernet node
ARM64: dts: marvell: armada-cp110: Add clocks for the xmdio node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
All interrupts from SoC internal modules are level triggered, so fix
incorrect trigger type for I2S1 device on Exynos5433 SoCs.
This fixes following kernel warning:
WARNING: CPU: 2 PID: 1 at drivers/irqchip/irq-gic.c:1016 gic_irq_domain_translate+0xb0/0xb8
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc7-next-20180329 #646
Hardware name: Samsung TM2 board (DT)
pstate: 20000005 (nzCv daif -PAN -UAO)
pc : gic_irq_domain_translate+0xb0/0xb8
lr : irq_create_fwspec_mapping+0x64/0x328
sp : ffff0000098b38d0
...
Call trace:
gic_irq_domain_translate+0xb0/0xb8
irq_create_of_mapping+0x78/0xa0
of_irq_get+0x6c/0xa0
of_irq_to_resource+0x38/0x108
of_irq_to_resource_table+0x50/0x78
of_device_alloc+0x118/0x1b8
of_platform_device_create_pdata+0x54/0xe0
of_platform_bus_create+0x118/0x340
of_platform_bus_create+0x17c/0x340
of_platform_populate+0x74/0xd8
of_platform_default_populate_init+0xb0/0xcc
do_one_initcall+0x50/0x158
kernel_init_freeable+0x184/0x22c
kernel_init+0x10/0x108
ret_from_fork+0x10/0x18
---[ end trace 6decb2b3078d73f0 ]---
Fixes: d8d579c316e8 ("ARM: dts: exynos: Add I2S1 device node to exynos5433")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into fixes
UniPhier ARM SoC fixes for v4.17
- Fix input delay parameter of eMMC PHY
- Weaken drive-strength of ethernet PHY pins of LD20 reference board
* tag 'uniphier-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: stabilize ethernet of LD20 reference board
arm64: dts: uniphier: fix input delay value for legacy mode of eMMC
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"There's a small memblock accounting problem when freeing the initrd
and a Spectre-v2 mitigation for NVIDIA Denver CPUs which just requires
a match on the CPU ID register.
Summary:
- Mitigate Spectre-v2 for NVIDIA Denver CPUs
- Free memblocks corresponding to freed initrd area"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: capabilities: Add NVIDIA Denver CPU to bp_harden list
arm64: Add MIDR encoding for NVIDIA CPUs
arm64: To remove initrd reserved area entry from memblock
|
|
The NVIDIA Denver CPU also needs a PSCI call to harden the branch
predictor.
Signed-off-by: David Gilhooley <dgilhooley@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch adds the MIDR encodings for NVIDIA as well as
the Denver and Carmel CPUs used in Tegra SoCs.
Signed-off-by: David Gilhooley <dgilhooley@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/arm fixes for 4.17, take #2
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
|
|
Proxying the cpuif accesses at EL2 makes use of vcpu_data_guest_to_host
and co, which check the endianness, which call into vcpu_read_sys_reg...
which isn't mapped at EL2 (it was inlined before, and got moved OoL
with the VHE optimizations).
The result is of course a nice panic. Let's add some specialized
cruft to keep the broken platforms that require this hack alive.
But, this code used vcpu_data_guest_to_host(), which expected us to
write the value to host memory, instead we have trapped the guest's
read or write to an mmio-device, and are about to replay it using the
host's readl()/writel() which also perform swabbing based on the host
endianness. This goes wrong when both host and guest are big-endian,
as readl()/writel() will undo the guest's swabbing, causing the
big-endian value to be written to device-memory.
What needs doing?
A big-endian guest will have pre-swabbed data before storing, undo this.
If its necessary for the host, writel() will re-swab it.
For a read a big-endian guest expects to swab the data after the load.
The hosts's readl() will correct for host endianness, giving us the
device-memory's value in the register. For a big-endian guest, swab it
as if we'd only done the load.
For a little-endian guest, nothing needs doing as readl()/writel() leave
the correct device-memory value in registers.
Tested on Juno with that rarest of things: a big-endian 64K host.
Based on a patch from Marc Zyngier.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: bf8feb39642b ("arm64: KVM: vgic-v2: Add GICV access from HYP")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
A typo in kvm_vcpu_set_be()'s call:
| vcpu_write_sys_reg(vcpu, SCTLR_EL1, sctlr)
causes us to use the 32bit register value as an index into the sys_reg[]
array, and sail off the end of the linear map when we try to bring up
big-endian secondaries.
| Unable to handle kernel paging request at virtual address ffff80098b982c00
| Mem abort info:
| ESR = 0x96000045
| Exception class = DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| Data abort info:
| ISV = 0, ISS = 0x00000045
| CM = 0, WnR = 1
| swapper pgtable: 4k pages, 48-bit VAs, pgdp = 000000002ea0571a
| [ffff80098b982c00] pgd=00000009ffff8803, pud=0000000000000000
| Internal error: Oops: 96000045 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 2 PID: 1561 Comm: kvm-vcpu-0 Not tainted 4.17.0-rc3-00001-ga912e2261ca6-dirty #1323
| Hardware name: ARM Juno development board (r1) (DT)
| pstate: 60000005 (nZCv daif -PAN -UAO)
| pc : vcpu_write_sys_reg+0x50/0x134
| lr : vcpu_write_sys_reg+0x50/0x134
| Process kvm-vcpu-0 (pid: 1561, stack limit = 0x000000006df4728b)
| Call trace:
| vcpu_write_sys_reg+0x50/0x134
| kvm_psci_vcpu_on+0x14c/0x150
| kvm_psci_0_2_call+0x244/0x2a4
| kvm_hvc_call_handler+0x1cc/0x258
| handle_hvc+0x20/0x3c
| handle_exit+0x130/0x1ec
| kvm_arch_vcpu_ioctl_run+0x340/0x614
| kvm_vcpu_ioctl+0x4d0/0x840
| do_vfs_ioctl+0xc8/0x8d0
| ksys_ioctl+0x78/0xa8
| sys_ioctl+0xc/0x18
| el0_svc_naked+0x30/0x34
| Code: 73620291 604d00b0 00201891 1ab10194 (957a33f8)
|---[ end trace 4b4a4f9628596602 ]---
Fix the order of the arguments.
Fixes: 8d404c4c24613 ("KVM: arm64: Rewrite system register accessors to read/write functions")
CC: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Since LD_ABS/LD_IND instructions are now removed from the core and
reimplemented through a combination of inlined BPF instructions and
a slow-path helper, we can get rid of the complexity from arm64 JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Need to configure PHY interrupt as active low for P3310 Tegra186
platform otherwise it results in spurious interrupts.
This issue wasn't seen before because the generic PHY driver without
interrupt support was used.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
INITRD reserved area entry is not removed from memblock
even though initrd reserved area is freed. After freeing
the memory it is released from memblock. The same can be
checked from /sys/kernel/debug/memblock/reserved.
The patch makes sure that the initrd entry is removed from
memblock when keepinitrd is not enabled.
The patch only affects accounting and debugging. This does not
fix any memory leak.
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: CHANDAN VN <chandan.vn@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Currently, the ethernet RGMII mode on the LD20 reference board is
unstable.
The default drive-strength of ethernet TX pins is too strong because
there is no dumping resistor on the TX lines on the board.
Weaken the drive-strength to make the ethernet more stable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Pull KVM fixes from Radim Krčmář:
"ARM:
- PSCI selection API, a leftover from 4.16 (for stable)
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address (linaro -> arm)
x86:
- Expose userspace-relevant bits of a newly added feature
- Fix TLB flushing on VMX with VPID, but without EPT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/headers/UAPI: Move DISABLE_EXITS KVM capability bits to the UAPI
kvm: apic: Flush TLB after APIC mode/address change if VPIDs are in use
arm/arm64: KVM: Add PSCI version selection API
KVM: arm/arm64: vgic: Kick new VCPU on interrupt migration
arm64: KVM: Demote SVE and LORegion warnings to debug only
MAINTAINERS: Update e-mail address for Christoffer Dall
KVM: arm/arm64: Close VMID generation race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Nothing too bad, but the spectre updates to smatch identified a few
places that may need sanitising so we've got those covered.
Details:
- Close some potential spectre-v1 vulnerabilities found by smatch
- Add missing list sentinel for CPUs that don't require KPTI
- Removal of unused 'addr' parameter for I/D cache coherency
- Removal of redundant set_fs(KERNEL_DS) calls in ptrace
- Fix single-stepping state machine handling in response to kernel
traps
- Clang support for 128-bit integers
- Avoid instrumenting our out-of-line atomics in preparation for
enabling LSE atomics by default in 4.18"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid instrumenting atomic_ll_sc.o
KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_mmio_read_apr()
KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_get_irq()
arm64: fix possible spectre-v1 in ptrace_hbp_get_event()
arm64: support __int128 with clang
arm64: only advance singlestep for user instruction traps
arm64/kernel: rename module_emit_adrp_veneer->module_emit_veneer_for_adrp
arm64: ptrace: remove addr_limit manipulation
arm64: mm: drop addr parameter from sync icache and dcache
arm64: add sentinel to kpti_safe_list
|
|
Marvell PPv2.2 controller present on CP-110 need the extra "mg_core_clk"
clock to avoid system hangs when powering some network interfaces up.
This issue appeared after a recent clock rework on Armada 7K/8K platforms.
This commit adds the new clock and updates the documentation accordingly.
[gregory.clement: use the real first commit to fix and add the cc:stable
flag]
Fixes: e3af9f7c6ece ("RM64: dts: marvell: armada-cp110: Fix clock resources for various node")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The Marvell XSMI controller needs 3 clocks to operate correctly :
- The MG clock (clk 5)
- The MG Core clock (clk 6)
- The GOP clock (clk 18)
This commit adds them, to avoid system hangs when using these
interfaces.
[gregory.clement: use the real first commit to fix and add the cc:stable
flag]
Fixes: f66b2aff46ea ("arm64: dts: marvell: add xmdio nodes for 7k/8k")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Our out-of-line atomics are built with a special calling convention,
preventing pointless stack spilling, and allowing us to patch call sites
with ARMv8.1 atomic instructions.
Instrumentation inserted by the compiler may result in calls to
functions not following this special calling convention, resulting in
registers being unexpectedly clobbered, and various problems resulting
from this.
For example, if a kernel is built with KCOV and ARM64_LSE_ATOMICS, the
compiler inserts calls to __sanitizer_cov_trace_pc in the prologues of
the atomic functions. This has been observed to result in spurious
cmpxchg failures, leading to a hang early on in the boot process.
This patch avoids such issues by preventing instrumentation of our
out-of-line atomics.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
https://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree-arm64 fixes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 4.17, please pull the following:
- Srinath fixes the register base address of all SATA controllers on
Stingray
* tag 'arm-soc/for-4.17/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: correct SATA addresses for Stingray
|
|
It's possible for userspace to control idx. Sanitize idx when using it
as an array index.
Found by smatch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.17-rc1" from Kevin Hilman:
- add / enable USB host support for GX boards
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
ARM64: dts: meson-gxm: add GXM specific USB host configuration
ARM64: dts: meson-gxl: add USB host support
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv8 Juno DT fix for v4.17" from Sudeep Holla:
A single patch to fix the new DTC warnings probably enabled during
v4.17 merge window.
* tag 'juno-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: drop unnecessary address-cells and size-cells properties
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/arm fixes for 4.17, take #1
- PSCI selection API, a leftover from 4.16
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address
|
|
Commit fb8722735f50 ("arm64: support __int128 on gcc 5+") added support
for arm64 __int128 with gcc with a version-conditional, but neglected to
enable this for clang, which in fact appears to support aarch64 __int128.
This commit therefore enables it if the compiler is clang, using the
same type of makefile conditional used elsewhere in the tree.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Our arm64_skip_faulting_instruction() helper advances the userspace
singlestep state machine, but this is also called by the kernel BRK
handler, as used for WARN*().
Thus, if we happen to hit a WARN*() while the user singlestep state
machine is in the active-no-pending state, we'll advance to the
active-pending state without having executed a user instruction, and
will take a step exception earlier than expected when we return to
userspace.
Let's fix this by only advancing the state machine when skipping a user
instruction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit a257e02579e ("arm64/kernel: don't ban ADRP to work around
Cortex-A53 erratum #843419") introduced a function whose name ends with
"_veneer".
This clashes with commit bd8b22d2888e ("Kbuild: kallsyms: ignore veneers
emitted by the ARM linker"), which removes symbols ending in "_veneer"
from kallsyms.
The problem was manifested as 'perf test -vvvvv vmlinux' failed,
correctly claiming the symbol 'module_emit_adrp_veneer' was present in
vmlinux, but not in kallsyms.
...
ERR : 0xffff00000809aa58: module_emit_adrp_veneer not on kallsyms
...
test child finished with -1
---- end ----
vmlinux symtab matches kallsyms: FAILED!
Fix the problem by renaming module_emit_adrp_veneer to
module_emit_veneer_for_adrp. Now the test passes.
Fixes: a257e02579e ("arm64/kernel: don't ban ADRP to work around Cortex-A53 erratum #843419")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We transiently switch to KERNEL_DS in compat_ptrace_gethbpregs() and
compat_ptrace_sethbpregs(), but in either case this is pointless as we
don't perform any uaccess during this window.
let's rip out the redundant addr_limit manipulation.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The property of the legacy mode for the eMMC PHY turned out to
be wrong. Some eMMC devices are unstable due to the set-up/hold
timing violation. Correct the delay value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The addr parameter isn't used for anything. Let's simplify and get rid of
it, like arm.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We're missing a sentinel entry in kpti_safe_list. Thus is_midr_in_range_list()
can walk past the end of kpti_safe_list. Depending on the contents of memory,
this could erroneously match a CPU's MIDR, cause a data abort, or other bad
outcomes.
Add the sentinel entry to avoid this.
Fixes: be5b299830c63ed7 ("arm64: capabilities: Add support for checks based on a list of MIDRs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Although we've implemented PSCI 0.1, 0.2 and 1.0, we expose either 0.1
or 1.0 to a guest, defaulting to the latest version of the PSCI
implementation that is compatible with the requested version. This is
no different from doing a firmware upgrade on KVM.
But in order to give a chance to hypothetical badly implemented guests
that would have a fit by discovering something other than PSCI 0.2,
let's provide a new API that allows userspace to pick one particular
version of the API.
This is implemented as a new class of "firmware" registers, where
we expose the PSCI version. This allows the PSCI version to be
save/restored as part of a guest migration, and also set to
any supported version if the guest requires it.
Cc: stable@vger.kernel.org #4.16
Reviewed-by: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Correct all SATA ahci and phy controller register
addresses and interrupt lines to proper values.
Fixes: 344a2e514182 ("arm64: dts: Add SATA DT nodes for Stingray SoC")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
