| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARMv8 Juno fixes for v5.5
Couple of fixes:
1. Fix for UART clock frequency on all Juno variants that exist since
the platform was added. This is mainly due to incorrect Juno SoC
TRM that was referred during initial development days
2. Drop "dma-ranges" property for now as they are triggering loads of
warning on boot
* tag 'juno-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
Revert "arm64: dts: juno: add dma-ranges property"
arm64: dts: juno: Fix UART frequency
arm64: dts: juno: add GPU subsystem
Link: https://lore.kernel.org/r/20191202114338.GA20965@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit 193d00a2b35ee3353813b4006a18131122087205.
Commit 951d48855d86 ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Fixes: 193d00a2b35e ("arm64: dts: juno: add dma-ranges property")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.
Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).
Fix this to correct the baud rate divisor calculation on the Juno board.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0515b.b/DDI0515B_b_juno_arm_development_platform_soc_trm.pdf
[2] http://infocenter.arm.com/help/topic/com.arm.doc.100113_0000_07_en/arm_versatile_express_juno_development_platform_(v2m_juno)_technical_reference_manual_100113_0000_07_en.pdf
Fixes: 71f867ec130e ("arm64: Add Juno board device tree.")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
Two OP-TE driver fixes:
- Add proper cleanup on optee_enumerate_devices() failure
- Make sure to register kernel allocations of dynamic shared memory
* tag 'tee-fixes-for-v5.4' of git://git.linaro.org/people/jens.wiklander/linux-tee: (591 commits)
tee: optee: fix device enumeration error handling
tee: optee: Fix dynamic shm pool allocations
Linux 5.4-rc3
tracing: Initialize iter->seq after zeroing in tracing_read_pipe()
tracing/hwlat: Don't ignore outer-loop duration when calculating max_latency
tracing/hwlat: Report total time spent in all NMIs during the sample
recordmcount: Fix nop_mcount() function
tracing: Do not create tracefs files if tracefs lockdown is in effect
tracing: Add locked_down checks to the open calls of files created for tracefs
tracing: Add tracing_check_open_get_tr()
tracing: Have trace events system open call tracing_open_generic_tr()
tracing: Get trace_array reference for available_tracers files
ftrace: Get a reference counter for the trace_array on filter files
tracefs: Revert ccbd54ff54e8 ("tracefs: Restrict tracefs when the kernel is locked down")
perf/x86/cstate: Add Tiger Lake CPU support
perf/x86/msr: Add Tiger Lake CPU support
perf/x86/intel: Add Tiger Lake CPU support
perf/x86/cstate: Update C-state counters for Ice Lake
perf/x86/msr: Add new CPU model numbers for Ice Lake
perf/x86/cstate: Add Comet Lake CPU support
...
Link: https://lore.kernel.org/r/20191115105353.GA26176@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 3rd round:
- Fix the GPIO number that is controlling core voltage on
imx8mq-zii-ultra board.
* tag 'imx-fixes-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
Link: https://lore.kernel.org/r/20191104084513.GW24620@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The GPIO handle is referencing the wrong GPIO, so the voltage did not
actually change as intended. The pinmux is already correct, so just
correct the GPIO number.
Fixes: 4a13b3bec3b4 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4, 2nd round:
- Get SNVS power key back to work for imx6-logicpd board. It was
accidentally disabled by commit 770856f0da5d ("ARM: dts: imx6qdl:
Enable SNVS power key according to board design").
- Fix sparse warnings in IMX GPC driver by making the initializers
in imx_gpc_domains C99 format.
- Fix an interrupt storm coming from accelerometer on imx6qdl-sabreauto
board. This is seen with upstream version U-Boot where pinctrl is not
configured for the device.
- Fix sdma device compatible string for i.MX8MM and i.MX8MN SoC.
- Fix compatible of PCA9547 i2c-mux on LS1028A QDS board to get the
device probed correctly.
* tag 'imx-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
Link: https://lore.kernel.org/r/20191029110334.GA20928@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
SDMA in i.MX8MN should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SDMA in i.MX8MM should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The I2C multiplexer used on ls1028aqds is PCA9547, not PCA9847.
If the wrong compatible was used, this chip will not be able to
be probed correctly and hence fail to work.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A number of fixes for individual boards like the rockpro64, and Hugsun X99
as well as a fix for the Gru-Kevin display override and fixing the dt-
binding for Theobroma boards to the correct naming that is also actually
used in the wild.
* tag 'v5.4-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
arm64: dts: rockchip: Fix usb-c on Hugsun X99 TV Box
arm64: dts: rockchip: fix RockPro64 sdmmc settings
arm64: dts: rockchip: fix RockPro64 sdhci settings
arm64: dts: rockchip: fix RockPro64 vdd-log regulator settings
dt-bindings: arm: rockchip: fix Theobroma-System board bindings
arm64: dts: rockchip: fix Rockpro64 RK808 interrupt line
Link: https://lore.kernel.org/r/1599050.HRXuSXmxRg@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 5.4, please pull the following:
- Rayangonda fixes the GPIO pins assignment for the Stringray SoCs
* tag 'arm-soc/for-5.4/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: Fix gpio to pinmux mapping
Link: https://lore.kernel.org/r/20191015172356.9650-2-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since we now have bindings for Mali Midgard GPUs, let's use them to
describe Juno's GPU subsystem, if only because we can. Juno sports a
Mali-T624 integrated behind an MMU-400 (as a gesture towards
virtualisation), in their own dedicated power domain with DVFS
controlled by the SCP.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Sudeep Holla <sudeep.holla@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
On i.MX8MN, usdhc's ipg clock is from IMX8MN_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MN_CLK_DUMMY.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MM, usdhc's ipg clock is from IMX8MM_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MM_CLK_DUMMY.
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MQ, usdhc's ipg clock is from IMX8MQ_CLK_IPG_ROOT,
assign it explicitly instead of using IMX8MQ_CLK_DUMMY.
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
lx2160a support PW15 but not PW20, correct name to avoid confusing.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Fixes: 00c5ce8ac023 ("arm64: dts: lx2160a: add cpu idle support")
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
|
|
arm/fixes
mvebu fixes for 5.4 (part 1)
Fix regression on USB for Turris Mox (Armada 3720 based board)
* tag 'mvebu-fixes-5.4-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: armada-3720-turris-mox: convert usb-phy to phy-supply
Link: https://lore.kernel.org/r/87blunsm43.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When I re-posted Sean's original commit to add the override mode for
the kevin panel, for some reason I didn't notice that the pixel clock
wasn't quite right. Looking at /sys/kernel/debug/clk/clk_summary on
downstream kernels it can be seen that the VOP clock is supposed to be
266,666,667 Hz achieved by dividing the 800 MHz PLL by 3.
Looking at history, it seems that even Sean's first patch [1] had this
funny clock rate. I'm not sure where it came from since the commit
message specifically mentioned 26666 kHz and the Chrome OS tree [2]
can be seen to request 266667 kHz.
In any case, let's fix it up. This together with my patch [3] to do
the proper rounding when setting the clock rate makes the VOP clock
more proper as seen in /sys/kernel/debug/clk/clk_summary.
[1] https://lore.kernel.org/r/20180206165626.37692-4-seanpaul@chromium.org
[2] https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/panel/panel-simple.c#1172
[3] https://lkml.kernel.org/r/20191003114726.v2.1.Ib233b3e706cf6317858384264d5b0ed35657456e@changeid
Fixes: 84ebd2da6d04 ("arm64: dts: rockchip: Specify override mode for kevin panel")
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191008124949.1.I674acd441997dd0690c86c9003743aacda1cf5dd@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix usb-c on X99 TV Box. Tested with armbian w/ kernel 5.3
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20190929032230.24628-1-npcomplete13@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to the RockPro64 schematic [1] the rk3399 sdmmc controller is
connected to a microSD (TF card) slot. Remove the cap-mmc-highspeed
property of the sdmmc controller, since no mmc card can be connected here.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191004203213.4995-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A larger-than-usual batch of arm64 fixes for -rc3.
The bulk of the fixes are dealing with a bunch of issues with the
build system from the compat vDSO, which unfortunately led to some
significant Makefile rework to manage the horrible combinations of
toolchains that we can end up needing to drive simultaneously.
We came close to disabling the thing entirely, but Vincenzo was quick
to spin up some patches and I ended up picking up most of the bits
that were left [*]. Future work will look at disentangling the header
files properly.
Other than that, we have some important fixes all over, including one
papering over the miscompilation fallout from forcing
CONFIG_OPTIMIZE_INLINING=y, which I'm still unhappy about. Harumph.
We've still got a couple of open issues, so I'm expecting to have some
more fixes later this cycle.
Summary:
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes"
[*] Will's final fixes were
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
but they were already in linux-next by then and he didn't rebase
just to add those.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (21 commits)
arm64: armv8_deprecated: Checking return value for memory allocation
arm64: Kconfig: Make CONFIG_COMPAT_VDSO a proper Kconfig option
arm64: vdso32: Rename COMPATCC to CC_COMPAT
arm64: vdso32: Pass '--target' option to clang via VDSO_CAFLAGS
arm64: vdso32: Don't use KBUILD_CPPFLAGS unconditionally
arm64: vdso32: Move definition of COMPATCC into vdso32/Makefile
arm64: Default to building compat vDSO with clang when CONFIG_CC_IS_CLANG
lib: vdso: Remove CROSS_COMPILE_COMPAT_VDSO
arm64: vdso32: Remove jump label config option in Makefile
arm64: vdso32: Detect binutils support for dmb ishld
arm64: vdso: Remove stale files from old assembly implementation
arm64: vdso32: Fix broken compat vDSO build warnings
arm64: mm: fix spurious fault detection
arm64: ftrace: Ensure synchronisation in PLT setup for Neoverse-N1 #1542419
arm64: Fix incorrect irqflag restore for priority masking for compat
arm64: mm: avoid virt_to_phys(init_mm.pgd)
arm64: cpufeature: Effectively expose FRINT capability to userspace
arm64: Mark functions using explicit register variables as '__always_inline'
docs: arm64: Fix indentation and doc formatting
arm64/sve: Fix wrong free for task->thread.sve_state
...
|
|
Update Turris Mox device tree to use the phy-supply property of the
generic PHY framework instead of the legacy usb-phy property.
This is needed since it caused a regression on Turris Mox since "usb:
host: xhci-plat: Prevent an abnormally restrictive PHY init skipping".
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: eb6c2eb6c7fb ("usb: host: xhci-plat: Prevent an abnormally restrictive PHY init skipping")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
There are no return value checking when using kzalloc() and kcalloc() for
memory allocation. so add it.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
CONFIG_COMPAT_VDSO is defined by passing '-DCONFIG_COMPAT_VDSO' to the
compiler when the generic compat vDSO code is in use. It's much cleaner
and simpler to expose this as a proper Kconfig option (like x86 does),
so do that and remove the bodge.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For consistency with CROSS_COMPILE_COMPAT, mechanically rename COMPATCC
to CC_COMPAT so that specifying aspects of the compat vDSO toolchain in
the environment isn't needlessly confusing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Directly passing the '--target' option to clang by appending to
COMPATCC does not work if COMPATCC has been specified explicitly as
an argument to Make unless the 'override' directive is used, which is
ugly and different to what is done in the top-level Makefile.
Move the '--target' option for clang out of COMPATCC and into
VDSO_CAFLAGS, where it will be picked up when compiling and assembling
the 32-bit vDSO under clang.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
KBUILD_CPPFLAGS is defined differently depending on whether the main
compiler is clang or not. This means that it is not possible to build
the compat vDSO with GCC if the rest of the kernel is built with clang.
Define VDSO_CPPFLAGS directly to break this dependency and allow a clang
kernel to build a compat vDSO with GCC:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \
CROSS_COMPILE_COMPAT=arm-linux-gnueabihf- CC=clang \
COMPATCC=arm-linux-gnueabihf-gcc
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
There's no need to export COMPATCC, so just define it locally in the
vdso32/Makefile, which is the only place where it is used.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Rather than force the use of GCC for the compat cross-compiler, instead
extract the target from CROSS_COMPILE_COMPAT and pass it to clang if the
main compiler is clang.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The jump labels are not used in vdso32 since it is not possible to run
runtime patching on them.
Remove the configuration option from the Makefile.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Older versions of binutils (prior to 2.24) do not support the "ISHLD"
option for memory barrier instructions, which leads to a build failure
when assembling the vdso32 library.
Add a compilation time mechanism that detects if binutils supports those
instructions and configure the kernel accordingly.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Moving over to the generic C implementation of the vDSO inadvertently
left some stale files behind which are no longer used. Remove them.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The .config file and the generated include/config/auto.conf can
end up out of sync after a set of commands since
CONFIG_CROSS_COMPILE_COMPAT_VDSO is not updated correctly.
The sequence can be reproduced as follows:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig
[...]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- menuconfig
[set CONFIG_CROSS_COMPILE_COMPAT_VDSO="arm-linux-gnueabihf-"]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-
Which results in:
arch/arm64/Makefile:62: CROSS_COMPILE_COMPAT not defined or empty,
the compat vDSO will not be built
even though the compat vDSO has been built:
$ file arch/arm64/kernel/vdso32/vdso.so
arch/arm64/kernel/vdso32/vdso.so: ELF 32-bit LSB pie executable, ARM,
EABI5 version 1 (SYSV), dynamically linked,
BuildID[sha1]=c67f6c786f2d2d6f86c71f708595594aa25247f6, stripped
A similar case that involves changing the configuration parameter
multiple times can be reconducted to the same family of problems.
Remove the use of CONFIG_CROSS_COMPILE_COMPAT_VDSO altogether and
instead rely on the cross-compiler prefix coming from the environment
via CROSS_COMPILE_COMPAT, much like we do for the rest of the kernel.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When detecting a spurious EL1 translation fault, we attempt to compare
ESR_EL1.DFSC with PAR_EL1.FST. We erroneously use FIELD_PREP() to
extract PAR_EL1.FST, when we should be using FIELD_GET().
In the wise words of Robin Murphy:
| FIELD_GET() is a UBFX, FIELD_PREP() is a BFI
Using FIELD_PREP() means that that dfsc & ESR_ELx_FSC_TYPE is always
zero, and hence not equal to ESR_ELx_FSC_FAULT. Thus we detect any
unhandled translation fault as spurious.
... so let's use FIELD_GET() to ensure we don't decide all translation
faults are spurious. ESR_EL1.DFSC occupies bits [5:0], and requires no
shifting.
Fixes: 42f91093b043332a ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The GPIO controlled regulator for the ARM power supply is supplying
the higher voltage when the GPIO is driven high. This is opposite to
the similar regulator setup on the EVK board and is impacting stability
of the board as the ARM domain has been supplied with a too low voltage
when to faster OPPs are in use.
Fixes: 4a13b3bec3b4 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
ARM: dts: ux500: Fix up the CPU thermal zone
arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
|
|
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is
connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module.
So the data strobe cannot be used for its intended purpose on this board,
and so the HS400 eMMC mode is not functional. Limit the controller to HS200.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] http://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-2-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a
max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an
additional note that the pwm parameter needs to be modified.
From the schematics a voltage range of 0.8V to 1.7V can be calculated.
Additional voltage measurements on the board show that this fix indeed
leads to the correct voltage, while without this fix the voltage was set
too high.
[1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Signed-off-by: Soeren Moch <smoch@web.de>
Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 bugfixes of all kinds.
The most visible one is that migrating a nested hypervisor has always
been busted on Broadwell and newer processors, and that has finally
been fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
KVM: x86: omit "impossible" pmu MSRs from MSR list
KVM: nVMX: Fix consistency check on injected exception error code
KVM: x86: omit absent pmu MSRs from MSR list
selftests: kvm: Fix libkvm build error
kvm: vmx: Limit guest PMCs to those supported on the host
kvm: x86, powerpc: do not allow clearing largepages debugfs entry
KVM: selftests: x86: clarify what is reported on KVM_GET_MSRS failure
KVM: VMX: Set VMENTER_L1D_FLUSH_NOT_REQUIRED if !X86_BUG_L1TF
selftests: kvm: add test for dirty logging inside nested guests
KVM: x86: fix nested guest live migration with PML
KVM: x86: assign two bits to track SPTE kinds
KVM: x86: Expose XSAVEERPTR to the guest
kvm: x86: Enumerate support for CLZERO instruction
kvm: x86: Use AMD CPUID semantics for AMD vCPUs
kvm: x86: Improve emulation of CPUID leaves 0BH and 1FH
KVM: X86: Fix userspace set invalid CR4
kvm: x86: Fix a spurious -E2BIG in __do_cpuid_func
KVM: LAPIC: Loosen filter for adaptive tuning of lapic_timer_advance_ns
KVM: arm/arm64: vgic: Use the appropriate TRACE_INCLUDE_PATH
arm64: KVM: Kill hyp_alternate_select()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- a fix in the Xen balloon driver avoiding hitting a BUG_ON() in some
cases, plus a follow-on cleanup series for that driver
- a patch for introducing non-blocking EFI callbacks in Xen's EFI
driver, plu a cleanup patch for Xen EFI handling merging the x86 and
ARM arch specific initialization into the Xen EFI driver
- a fix of the Xen xenbus driver avoiding a self-deadlock when cleaning
up after a user process has died
- a fix for Xen on ARM after removal of ZONE_DMA
- a cleanup patch for avoiding build warnings for Xen on ARM
* tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: fix self-deadlock after killing user process
xen/efi: have a common runtime setup function
arm: xen: mm: use __GPF_DMA32 for arm64
xen/balloon: Clear PG_offline in balloon_retrieve()
xen/balloon: Mark pages PG_offline in balloon_append()
xen/balloon: Drop __balloon_append()
xen/balloon: Set pages PageOffline() in balloon_add_region()
ARM: xen: unexport HYPERVISOR_platform_op function
xen/efi: Set nonblocking callbacks
|
|
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CPUs affected by Neoverse-N1 #1542419 may execute a stale instruction if
it was recently modified. The affected sequence requires freshly written
instructions to be executable before a branch to them is updated.
There are very few places in the kernel that modify executable text,
all but one come with sufficient synchronisation:
* The module loader's flush_module_icache() calls flush_icache_range(),
which does a kick_all_cpus_sync()
* bpf_int_jit_compile() calls flush_icache_range().
* Kprobes calls aarch64_insn_patch_text(), which does its work in
stop_machine().
* static keys and ftrace both patch between nops and branches to
existing kernel code (not generated code).
The affected sequence is the interaction between ftrace and modules.
The module PLT is cleaned using __flush_icache_range() as the trampoline
shouldn't be executable until we update the branch to it.
Drop the double-underscore so that this path runs kick_all_cpus_sync()
too.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Commit bd82d4bd2188 ("arm64: Fix incorrect irqflag restore for priority
masking") added a macro to the entry.S call paths that leave the
PSTATE.I bit set. This tells the pPNMI masking logic that interrupts
are masked by the CPU, not by the PMR. This value is read back by
local_daif_save().
Commit bd82d4bd2188 added this call to el0_svc, as el0_svc_handler
is called with interrupts masked. el0_svc_compat was missed, but should
be covered in the same way as both of these paths end up in
el0_svc_common(), which expects to unmask interrupts.
Fixes: bd82d4bd2188 ("arm64: Fix incorrect irqflag restore for priority masking")
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
If we take an unhandled fault in the kernel, we call show_pte() to dump
the {PGDP,PGD,PUD,PMD,PTE} values for the corresponding page table walk,
where the PGDP value is virt_to_phys(mm->pgd).
The boot-time and runtime kernel page tables, init_pg_dir and
swapper_pg_dir respectively, are kernel symbols. Thus, it is not valid
to call virt_to_phys() on either of these, though we'll do so if we take
a fault on a TTBR1 address.
When CONFIG_DEBUG_VIRTUAL is not selected, virt_to_phys() will silently
fix this up. However, when CONFIG_DEBUG_VIRTUAL is selected, this
results in splats as below. Depending on when these occur, they can
happen to suppress information needed to debug the original unhandled
fault, such as the backtrace:
| Unable to handle kernel paging request at virtual address ffff7fffec73cf0f
| Mem abort info:
| ESR = 0x96000004
| EC = 0x25: DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| Data abort info:
| ISV = 0, ISS = 0x00000004
| CM = 0, WnR = 0
| ------------[ cut here ]------------
| virt_to_phys used for non-linear address: 00000000102c9dbe (swapper_pg_dir+0x0/0x1000)
| WARNING: CPU: 1 PID: 7558 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0xe0/0x170 arch/arm64/mm/physaddr.c:12
| Kernel panic - not syncing: panic_on_warn set ...
| SMP: stopping secondary CPUs
| Dumping ftrace buffer:
| (ftrace buffer empty)
| Kernel Offset: disabled
| CPU features: 0x0002,23000438
| Memory Limit: none
| Rebooting in 1 seconds..
We can avoid this by ensuring that we call __pa_symbol() for
init_mm.pgd, as this will always be a kernel symbol. As the dumped
{PGD,PUD,PMD,PTE} values are the raw values from the relevant entries we
don't need to handle these specially.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The HWCAP framework will detect a new capability based on the sanitized
version of the ID registers.
Sanitization is based on a whitelist, so any field not described will end
up to be zeroed.
At the moment, ID_AA64ISAR1_EL1.FRINTTS is not described in
ftr_id_aa64isar1. This means the field will be zeroed and therefore the
userspace will not be able to see the HWCAP even if the hardware
supports the feature.
This can be fixed by describing the field in ftr_id_aa64isar1.
Fixes: ca9503fc9e98 ("arm64: Expose FRINT capabilities to userspace")
Signed-off-by: Julien Grall <julien.grall@arm.com>
Cc: mark.brown@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
As of ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly"),
inline functions are no longer annotated with '__always_inline', which
allows the compiler to decide whether inlining is really a good idea or
not. Although this is a great idea on paper, the reality is that AArch64
GCC prior to 9.1 has been shown to get confused when creating an
out-of-line copy of a function passing explicit 'register' variables
into an inline assembly block:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91111
It's not clear whether this is specific to arm64 or not but, for now,
ensure that all of our functions using 'register' variables are marked
as '__always_inline' so that the old behaviour is effectively preserved.
Hopefully other architectures are luckier with their compilers.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
