| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 6.2 (part 1)
Fix regression for gpio support on Armada 38x and Armada 38x
Fix address for UART1 on AC5/AC5X
* tag 'mvebu-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: AC5/AC5X: Fix address for UART1
Revert "ARM: dts: armada-39x: Fix compatible string for gpios"
Revert "ARM: dts: armada-38x: Fix compatible string for gpios"
Link: https://lore.kernel.org/r/87mt6mg08k.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DTS fixes for 6.2
The cluster idle issue was resolved on SM8250, so the change disabling
the cluster state is being reverted.
Issues where identified with the QMP PHY binding, that would prevent
enablement of Displayport and it was decided not to support the old
binding for the recently introduced SC8280XP, which broke USB. This
adjusts the USB PHY nodes to the new binding. The reset signal for the
first QMP PHY is corrected as well.
The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus 6P,
to avoid instabilities caused by use of protected memory regions.
The compatible for the MSM8992 TCSR mutex is corrected as well.
Lastly SDHCI interconnects on SM8350 are corrected to match the
providers #interconnect-cells.
* tag 'qcom-arm64-fixes-for-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: msm8992-libra: Fix the memory map
arm64: dts: qcom: msm8992: Don't use sfpb mutex
arm64: dts: msm8994-angler: fix the memory map
arm64: dts: qcom: sm8350: correct SDHCI interconnect arguments
Revert "arm64: dts: qcom: sm8250: Disable the not yet supported cluster idle state"
arm64: dts: msm8992-bullhead: add memory hole region
arm64: dts: qcom: sc8280xp: fix USB-DP PHY nodes
arm64: dts: qcom: sc8280xp: fix primary USB-DP PHY reset
Link: https://lore.kernel.org/r/20230110213724.2183668-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The memory map was wrong. Fix it to prevent the device from randomly
rebooting.
Fixes: 0f5cdb31e850 ("arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219131918.446587-2-konrad.dybcio@linaro.org
|
|
MSM8992 uses the same mutex hardware as MSM8994. This was wrong
from the start, but never presented as an issue until the sfpb
compatible was given different driver data.
Fixes: 6a6d1978f9c0 ("arm64: dts: msm8992 SoC and LG Bullhead (Nexus 5X) support")
Reported-by: Eugene Lepshy <fekz115@gmail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219131918.446587-1-konrad.dybcio@linaro.org
|
|
Add reserved regions for memory hole and tz app mem to prevent
rebooting. Also enable cont_splash_mem, it is the same as the
generic 8994 one.
Reported-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230194845.57780-1-dominikkobinski314@gmail.com
|
|
The correct address offset is 0x12100.
Fixes: 31be791e26cf ("arm64: dts: marvell: Add UART1-3 for AC5/AC5X")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.2:
- Fix i.MX8MP DT for missing GPC Interrupt, power-domain typo and USB
clock error.
- Fix mach-imx cpu code to add missing of_node_put() call.
- A couple of verdin-imx8mm DT fixes for audio playback support.
- Fix pca9547 i2c-mux node name for i.MX and Vybrid device trees.
- Fix an imx93-11x11-evk uSDHC pad setting problem that causes Micron
eMMC CMD8 CRC error in HS400ES/HS400 mode.
- A couple of imx8mp-blk-ctrl driver fixes from Lucas Stach, enabling
pixclk with HDMI_TX_PHY PD, dropping power device name setting.
- Fix the error check for of_clk_get_by_name() in soc-imx8m driver.
- Other various DT fixes and cleanups.
* tag 'imx-fixes-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
soc: imx8m: Fix incorrect check for of_clk_get_by_name()
arm64: dts: imx8mm-venice-gw7901: fix USB2 controller OC polarity
arm64: dts: imx8mp-evk: pcie0-refclk cosmetic cleanup
arm64: dts: imx8mp: Fix power-domain typo
arm64: dts: imx8mp: Fix missing GPC Interrupt
soc: imx: imx8mp-blk-ctrl: don't set power device name
arm64: dts: imx8mm: Drop xtal clock specifier from eDM SBC
ARM: imx: add missing of_node_put()
arm64: dts: imx93-11x11-evk: correct clock and strobe pad setting
arm64: dts: verdin-imx8mm: fix dev board audio playback
arm64: dts: imx8mq-thor96: fix no-mmc property for SDHCI
arm64: dts: imx8mm-beacon: Fix ecspi2 pinmux
arm64: dts: freescale: Fix pca954x i2c-mux node names
ARM: dts: vf610: Fix pca9548 i2c-mux node names
ARM: dts: imx: Fix pca9547 i2c-mux node name
arm64: dts: verdin-imx8mm: fix dahlia audio playback
ARM: dts: imx6qdl-gw560x: Remove incorrect 'uart-has-rtscts'
ARM: dts: imx7d-pico: Use 'clock-frequency'
ARM: dts: imx6ul-pico-dwarf: Use 'clock-frequency'
arm64: dts: imx8mp-phycore-som: Remove invalid PMIC property
...
Link: https://lore.kernel.org/r/20230102132016.GA10699@T480
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit 703e84d6615a4a95fb504c8f2e4c9426b86f3930.
USB device enumeration was not working on Odroid HC4 as both USB2 PHYs
need to be enabled. This is inherited from the GLX USB design [1].
[1]: https://lore.kernel.org/all/20170814224542.18257-1-martin.blumenstingl@googlemail.com/T/
Signed-off-by: Pierre-Olivier Mercier <nemunaire@nemunai.re>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230105120206.28964-1-nemunaire@nemunai.re
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
The GW7901 has USB2 routed to a USB VBUS supply with over-current
protection via an active-low pin. Define the OC pin polarity properly.
Fixes: 2b1649a83afc ("arm64: dts: imx: Add i.mx8mm Gateworks gw7901 dts support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the correct indention.
Fixes: d50650500064 ("arm64: dts: imx8mp-evk: Add PCIe support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dt_binding_check detects an issue with the pgc_hsiomix power
domain:
pgc: 'power-domains@17' does not match any of the regexes
This is because 'power-domains' should be 'power-domain'
Fixes: 2ae42e0c0b67 ("arm64: dts: imx8mp: add HSIO power-domains")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPC node references an interrupt parent, but it doesn't
state the interrupt itself. According to the TRM, this IRQ
is 87. This also eliminate an error detected from dt_binding_check
Fixes: fc0f05124621 ("arm64: dts: imx8mp: add GPC node with GPU power domains")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The clk_xtal32k have clock-cells = <0>, drop the bogus specifier.
Fixes: 9509593f327a ("arm64: dts: imx8mm: Model PMIC to SNVS RTC clock path on Data Modul i.MX8M Mini eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
For clock and strobe pad of usdhc, need to config as pull down.
Current pad config set these pad as both pull up and pull down,
this is wrong, so fix it here.
Find this issue when enable HS400ES mode on one Micron eMMC chip,
CMD8 always meet CRC error in HS400ES/HS400 mode.
Fixes: e37907bd8294 ("arm64: dts: freescale: add i.MX93 11x11 EVK basic support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the nau8822 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is faster.
Set the MCLK at the right frequency, codec can properly use it to
generate 44.1 kHz I2S-FS.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no "no-emmc" property, so intention for SD/SDIO only nodes was
to use "no-mmc".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Early hardware did not support hardware handshaking on the UART, but
final production hardware did. When the hardware was updated the chip
select was changed to facilitate hardware handshaking on UART3. Fix the
ecspi2 pin mux to eliminate a pin conflict with UART3 and allow the
EEPROM to operate again.
Fixes: 4ce01ce36d77 ("arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
"make dtbs_check":
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: $nodename:0: 'pca9547@77' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@4' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the wm8904 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is completely distorted.
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
'regulator-compatible' is not a valid property according to
nxp,pca9450-regulator.yaml and causes the following warning:
DTC_CHK arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dtb
...
pmic@25: regulators:LDO1: Unevaluated properties are not allowed ('regulator-compatible' was unexpected)
Remove the invalid 'regulator-compatible' property.
Cc: Teresa Remmet <t.remmet@phytec.de>
Fixes: 88f7f6bcca37 ("arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After commit cf7f3f4fa9e5 ("clk: imx8mp: fix usb_root_clk parent"),
usb_root_clk is no longer for suspend clock so update dts accordingly
to use right bus clock and suspend clock.
Fixes: fb8587a2c165 ("arm64: dtsi: imx8mp: add usb nodes")
Cc: stable@vger.kernel.org # ed1f4ccfe947: clk: imx: imx8mp: add shared clk gate for usb suspend clk
Cc: stable@vger.kernel.org # v5.19+
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The interconnect providers accept only one argument (cells == 1), so fix
a copy&paste from SM8450:
sm8350-hdk.dtb: mmc@8804000: interconnects: [[74, 9, 0], [75, 1, 0], [76, 2, 0], [77, 36, 0]] is too long
Fixes: 60477435e4de ("arm64: dts: qcom: sm8350: Add SDHCI2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221224214351.18215-1-krzysztof.kozlowski@linaro.org
|
|
state"
Due to recent improvements of the cluster idle state support for Qcom based
platforms, we are now able to support the deepest cluster idle state. Let's
therefore revert the earlier workaround.
This reverts commit cadaa773bcf1 ("arm64: dts: qcom: sm8250: Disable the
not yet supported cluster idle state"), which is available from v6.1-rc6.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221122123713.65631-1-ulf.hansson@linaro.org
|
|
Add region for memory hole present on bullhead in order to
fix a reboot issue on recent kernels
Reported-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221211100501.82323-1-dominikkobinski314@gmail.com
|
|
Update the USB4-USB3-DP QMP PHY nodes to match the new binding which
specifically includes the missing register regions (e.g. DP_PHY) and
allows for supporting DisplayPort Alternate Mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121085058.31213-16-johan+linaro@kernel.org
|
|
The vendor kernel is using the GCC_USB4_DP_PHY_PRIM_BCR and
GCC_USB4_1_DP_PHY_PRIM_BCR resets for the USB4-USB3-DP QMP PHYs.
Update the primary USB-DP PHY node to match.
Fixes: 152d1faf1e2f ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121085058.31213-15-johan+linaro@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"rproc-virtio device names are now auto generated, to avoid conflicts
between remoteproc instances.
The imx_rproc driver is extended with support for communicating with
and attaching to a running M4 on i.MX8QXP, as well as support for
attaching to the M4 after self-recovering from a crash. Support is
added for i.MX8QM and mailbox channels are reconnected during the
recovery process, in order to avoid data corruption.
The Xilinx Zynqmp firmware interface is extended and support for the
Xilinx R5 RPU is introduced.
Various resources leaks, primarily in error paths, throughout the
Qualcomm drivers are corrected.
Lastly a fix to ensure that pm_relax is invoked even if the remoteproc
instance is stopped between a crash is being reported and the recovery
handler is scheduled"
* tag 'rproc-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (25 commits)
remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in q6v5_wcss_qcs404_power_on()
remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in adsp_alloc_memory_region()
remoteproc: qcom_q6v5_pas: detach power domains on remove
remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio()
remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
remoteproc: sysmon: Make QMI message rules const
drivers: remoteproc: Add Xilinx r5 remoteproc driver
firmware: xilinx: Add RPU configuration APIs
firmware: xilinx: Add shutdown/wakeup APIs
firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration.
arm64: dts: xilinx: zynqmp: Add RPU subsystem device node
dt-bindings: remoteproc: Add Xilinx RPU subsystem bindings
remoteproc: core: Use device_match_of_node()
remoteproc: imx_rproc: Correct i.MX93 DRAM mapping
remoteproc: imx_rproc: Enable attach recovery for i.MX8QM/QXP
remoteproc: imx_rproc: Request mbox channel later
remoteproc: imx_rproc: Support i.MX8QM
remoteproc: imx_rproc: Support kicking Mcore from Linux for i.MX8QXP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a couple of build fixes from randconfig testing, plus a set
of Mediatek SoC specific fixes, all trivial"
* tag 'soc-fixes-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: tegra: fix CPU_BIG_ENDIAN dependencies
ARM: disallow pre-ARMv5 builds with ld.lld
ARM: pxa: fix building with clang
MAINTAINERS: add related dts to IXP4xx
ARM: dts: spear: drop 0x from unit address
arm64: dts: mt8183: Fix Mali GPU clock
arm64: dts: mediatek: mt8195-demo: fix the memory size of node secmon
soc: mediatek: pm-domains: Fix the power glitch issue
|
|
The actual clock feeding into the Mali GPU on the MT8183 is from the
clock gate in the MFGCFG block, not CLK_TOP_MFGPLL_CK from the TOPCKGEN
block, which itself is simply a pass-through placeholder for the MFGPLL
in the APMIXEDSYS block.
Fix the hardware description with the correct clock reference.
Fixes: a8168cebf1bc ("arm64: dts: mt8183: Add node for the Mali GPU")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220927101128.44758-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The size of device tree node secmon (bl31_secmon_reserved) was
incorrect. It should be increased to 2MiB (0x200000).
The origin setting will cause some abnormal behavior due to
trusted-firmware-a and related firmware didn't load correctly.
The incorrect behavior may vary because of different software stacks.
For example, it will cause build error in some Yocto project because
it will check if there was enough memory to load trusted-firmware-a
to the reserved memory.
When mt8195-demo.dts sent to the upstream, at that time the size of
BL31 was small. Because supported functions and modules in BL31 are
basic sets when the board was under early development stage.
Now BL31 includes more firmwares of coprocessors and maturer functions
so the size has grown bigger in real applications. According to the value
reported by customers, we think reserved 2MiB for BL31 might be enough
for maybe the following 2 or 3 years.
Cc: stable@vger.kernel.org # v5.19
Fixes: 6147314aeedc ("arm64: dts: mediatek: Add device-tree for MT8195 Demo board")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221111095540.28881-1-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
|
|
Pull drm updates from Dave Airlie:
"The biggest highlight is that the accel subsystem framework is merged.
Hopefully for 6.3 we will be able to line up a driver to use it.
In drivers land, i915 enables DG2 support by default now, and nouveau
has a big stability refactoring and initial ampere support, AMD
includes new hw IP support and should build on ARM again. There is
also an ofdrm driver to take over offb on platforms it's used.
Stuff outside my tree, the dma-buf patches hit a few places, the vc4
firmware changes also do, and i915 has some interactions with MEI for
discrete GPUs. I think all of those should have been acked/reviewed by
relevant parties.
New driver:
- ofdrm - replacement for offb
fbdev:
- add support for nomodeset
fourcc:
- add Vivante tiled modifier
core:
- atomic-helpers: CRTC primary plane test fixes, fb access hooks
- connector: TV API consistency, cmdline parser improvements
- send connector hotplug on cleanup
- sort makefile objects
tests:
- sort kunit tests
- improve DP-MST tests
- add kunit helpers to create a device
sched:
- module param for scheduling policy
- refcounting fix
buddy:
- add back random seed log
ttm:
- convert ttm_resource to size_t
- optimize pool allocations
edid:
- HFVSDB parsing support fixes
- logging/debug improvements
- DSC quirks
dma-buf:
- Add unlocked vmap and attachment mapping
- move drivers to common locking convention
- locking improvements
firmware:
- new API for rPI firmware and vc4
xilinx:
- zynqmp: displayport bridge support
- dpsub fix
bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support, sync improvements
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
panel:
- panel-edp: Add INX N116BGE-EA2 C2 and C4 support.
- Jadard JD9365DA-H3
- NewVision NV3051D
amdgpu:
- DCN support on ARM
- DCN 2.1 secure display
- Sienna Cichlid mode2 reset fixes
- new GC 11.x firmware versions
- drop AMD specific DSC workarounds in favour of drm code
- clang warning fixes
- scheduler rework
- SR-IOV fixes
- GPUVM locking fixes
- fix memory leak in CS IOCTL error path
- flexible array updates
- enable new GC/PSP/SMU/NBIO IP
- GFX preemption support for gfx9
amdkfd:
- cache size fixes
- userptr fixes
- enable cooperative launch on gfx 10.3
- enable GC 11.0.4 KFD support
radeon:
- replace kmap with kmap_local_page
- ACPI ref count fix
- HDA audio notifier support
i915:
- DG2 enabled by default
- MTL enablement work
- hotplug refactoring
- VBT improvements
- Display and watermark refactoring
- ADL-P workaround
- temp disable runtime_pm for discrete-
- fix for A380 as a secondary GPU
- Wa_18017747507 for DG2
- CS timestamp support fixes for gen5 and earlier
- never purge busy TTM objects
- use i915_sg_dma_sizes for all backends
- demote GuC kernel contexts to normal priority
- gvt: refactor for new MDEV interface
- enable DC power states on eDP ports
- fix gen 2/3 workarounds
nouveau:
- fix page fault handling
- Ampere acceleration support
- driver stability improvements
- nva3 backlight support
msm:
- MSM_INFO_GET_FLAGS support
- DPU: XR30 and P010 image formats
- Qualcomm SM6115 support
- DSI PHY support for QCM2290
- HDMI: refactored dev init path
- remove exclusive-fence hack
- fix speed-bin detection
- enable clamp to idle on 7c3
- improved hangcheck detection
vmwgfx:
- fb and cursor refactoring
- convert to generic hashtable
- cursor improvements
etnaviv:
- hw workarounds
- softpin MMU fixes
ast:
- atomic gamma LUT support
- convert to SHMEM
lcdif:
- support YUV planes
- Increase DMA burst size
- FIFO threshold tuning
meson:
- fix return type of cvbs mode_valid
mgag200:
- fix PLL setup on some revisions
sun4i:
- A100 and D1 support
udl:
- modesetting improvements
- hot unplug support
vc4:
- support PAL-M
- fix regression preventing 4K @ 60Hz
- fix NULL ptr deref
v3d:
- switch to drm managed resources
renesas:
- RZ/G2L DSI support
- DU Kconfig cleanup
mediatek:
- fixup dpi and hdmi
- MT8188 dpi support
- MT8195 AFBC support
tegra:
- NVDEC hardware on Tegra234 SoC
hdlcd:
- switch to drm managed resources
ingenic:
- fix registration error path
hisilicon:
- convert to drm_mode_init
maildp:
- use managed resources
mtk:
- use drm_mode_init
rockchip:
- use drm_mode_copy"
* tag 'drm-next-2022-12-13' of git://anongit.freedesktop.org/drm/drm: (1397 commits)
drm/amdgpu: fix mmhub register base coding error
drm/amdgpu: add tmz support for GC IP v11.0.4
drm/amdgpu: enable GFX Clock Gating control for GC IP v11.0.4
drm/amdgpu: enable GFX Power Gating for GC IP v11.0.4
drm/amdgpu: enable GFX IP v11.0.4 CG support
drm/amdgpu: Make amdgpu_ring_mux functions as static
drm/amdgpu: generally allow over-commit during BO allocation
drm/amd/display: fix array index out of bound error in DCN32 DML
drm/amd/display: 3.2.215
drm/amd/display: set optimized required for comp buf changes
drm/amd/display: Add debug option to skip PSR CRTC disable
drm/amd/display: correct DML calc error of UrgentLatency
drm/amd/display: correct static_screen_event_mask
drm/amd/display: Ensure commit_streams returns the DC return code
drm/amd/display: read invalid ddc pin status cause engine busy
drm/amd/display: Bypass DET swath fill check for max clocks
drm/amd/display: Disable uclk pstate for subvp pipes
drm/amd/display: Fix DCN2.1 default DSC clocks
drm/amd/display: Enable dp_hdmi21_pcon support
drm/amd/display: prevent seamless boot on displays that don't have the preferred dig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- DVB core changes to avoid refcount troubles and UAF
- DVB API/core has gained support for DVB-C2 and DVB-S2X
- New sensor drivers: ov08x40, ov4689.c, st-vgxy61 and tc358746.c
- Removal of an unused sensor driver: s5k4ecgx
- Move microchip_csi2dc to a new directory, named after the
manufacturer
- Add media controller support to Microship drivers
- Old Atmel/Microship drivers that don't use media controler got moved
to staging
- New drivers added for Renesas RZ/G2L CRU and MIPI CSI-2 support
- Allwinner A31 camera sensor driver code was now split into a bridge
and a separate processor driver
- Added a virtual stateless decoder driver in order to test core
support for stateless drivers and test userspace apps using it
- removed platform-based support for ov9650, as this is not used
anymore
- atomisp now uses videobuf2 and supports normal mmap mode
- the imx7-media-csi driver got promoted from staging
- rcar-vin driver has gained support for gen3 UDS (Up Down Scaler)
- most i2c drivers now use I2C .probe_new() kAPI
- lots of drivers fixes, cleanups and improvements
* tag 'media/v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (544 commits)
media: s5c73m3: Switch to GPIO descriptors
media: i2c: s5k5baf: switch to using gpiod API
media: i2c: s5k6a3: switch to using gpiod API
media: imx: remove code for non-existing config IMX_GPT_ICAP
media: si470x: Fix use-after-free in si470x_int_in_callback()
media: staging: stkwebcam: Restore MEDIA_{USB,CAMERA}_SUPPORT dependencies
media: coda: Add check for kmalloc
media: coda: Add check for dcoda_iram_alloc
dt-bindings: media: s5c73m3: Fix reset-gpio descriptor
media: dt-bindings: allwinner: h6-vpu-g2: Add IOMMU reference property
media: s5k4ecgx: Delete driver
media: s5k4ecgx: Switch to GPIO descriptors
media: Switch to use dev_err_probe() helper
headers: Remove some left-over license text in include/uapi/linux/v4l2-*
headers: Remove some left-over license text in include/uapi/linux/dvb/
media: usb: pwc-uncompress: Use flex array destination for memcpy()
media: s5p-mfc: Fix to handle reference queue during finishing
media: s5p-mfc: Clear workbit to handle error condition
media: s5p-mfc: Fix in register read and write for H264
media: imx: Use get_mbus_config instead of parsing upstream DT endpoints
...
|
|
Add bluetooth controller nodes and the required brcm,board-type
properties to be able to select the correct firmware to all board
device trees.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include two new drivers (cpufreq driver for Apple SoC CPU
P-states and the SCMI Powercap based power capping driver), other new
hardware support and driver extensions (Qualcomm cpufreq driver and
its DT bindings, TI cpufreq driver, intel_pstate, intel-uncore-freq),
a bunch of fixes and cleanups all over and a cpupower utility update
including new features related to RAPL support.
Specifics:
- Fix nasty and hard to debug race condition introduced by mistake in
the runtime PM core code and clean up that code somewhat on top of
the fix (Rafael Wysocki)
- Generalize of_perf_domain_get_sharing_cpumask phandle format
(Hector Martin)
- Add new cpufreq driver for Apple SoC CPU P-states (Hector Martin)
- Update Qualcomm cpufreq driver (Manivannan Sadhasivam, Chen Hui):
- CPU clock provider support
- Generic cleanups or reorganization
- Potential memleak fix
- Fix of the return value of cpufreq_driver->get()
- Update Qualcomm cpufreq driver's DT bindings (Manivannan
Sadhasivam, Rob Herring, Melody Olvera):
- Support for CPU clock provider
- Missing cache-related properties fixes
- Support for QDU1000/QRU1000
- Add support for ti,am625 SoC and enable build of ti-cpufreq for
ARCH_K3 (Dave Gerlach, and Vibhore Vardhan)
- Use flexible array to simplify memory allocation in the tegra186
cpufreq driver (Christophe JAILLET)
- Convert cpufreq statistics code to use sysfs_emit_at() (ye
xingchen)
- Allow intel_pstate to use no-HWP mode on Sapphire Rapids (Giovanni
Gherdovich)
- Add missing pci_dev_put() to the amd_freq_sensitivity cpufreq
driver (Xiongfeng Wang)
- Initialize the kobj_unregister completion before calling
kobject_init_and_add() in the cpufreq core code (Yongqiang Liu)
- Defer setting boost MSRs in the ACPI cpufreq driver (Stuart Hayes,
Nathan Chancellor)
- Make intel_pstate accept initial EPP value of 0x80 (Srinivas
Pandruvada)
- Make read-only array sys_clk_src in the SPEAr cpufreq driver static
(Colin Ian King)
- Make array speeds in the longhaul cpufreq driver static (Colin Ian
King)
- Use str_enabled_disabled() helper in the ACPI cpufreq driver (Andy
Shevchenko)
- Drop a reference to CVS from cpufreq documentation (Conghui Wang)
- Improve kernel messages printed by the PSCI cpuidle driver (Ulf
Hansson)
- Make the DT cpuidle driver return the correct number of parsed idle
states, clean it up and clarify a comment in it (Ulf Hansson)
- Modify the tasks freezing code to avoid using pr_cont() and refine
an error message printed by it (Rafael Wysocki)
- Make the hibernation core code complain about memory map mismatches
during resume to help diagnostics (Xueqin Luo)
- Fix mistake in a kerneldoc comment in the hibernation code
(xiongxin)
- Reverse the order of performance and enabling operations in the
generic power domains code (Abel Vesa)
- Power off[on] domains in hibernate .freeze[thaw]_noirq hook of in
the generic power domains code (Abel Vesa)
- Consolidate genpd_restore_noirq() and genpd_resume_noirq() (Shawn
Guo)
- Pass generic PM noirq hooks to genpd_finish_suspend() (Shawn Guo)
- Drop generic power domain status manipulation during hibernate
restore (Shawn Guo)
- Fix compiler warnings with make W=1 in the idle_inject power
capping driver (Srinivas Pandruvada)
- Use kstrtobool() instead of strtobool() in the power capping sysfs
interface (Christophe JAILLET)
- Add SCMI Powercap based power capping driver (Cristian Marussi)
- Add Emerald Rapids support to the intel-uncore-freq driver (Artem
Bityutskiy)
- Repair slips in kernel-doc comments in the generic notifier code
(Lukas Bulwahn)
- Fix several DT issues in the OPP library reorganize code around
opp-microvolt-<named> DT property (Viresh Kumar)
- Allow any of opp-microvolt, opp-microamp, or opp-microwatt
properties to be present without the others present (James
Calligeros)
- Fix clock-latency-ns property in DT example (Serge Semin)
- Add a private governor_data for devfreq governors (Kant Fan)
- Reorganize devfreq code to use device_match_of_node() and
devm_platform_get_and_ioremap_resource() instead of open coding
them (ye xingchen, Minghao Chi)
- Make cpupower choose base_cpu to display default cpupower details
instead of picking CPU 0 (Saket Kumar Bhaskar)
- Add Georgian translation to cpupower documentation (Zurab
Kargareteli)
- Introduce powercap intel-rapl library, powercap-info command, and
RAPL monitor into cpupower (Thomas Renninger)"
* tag 'pm-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
PM: runtime: Adjust white space in the core code
cpufreq: Remove CVS version control contents from documentation
cpufreq: stats: Convert to use sysfs_emit_at() API
cpufreq: ACPI: Only set boost MSRs on supported CPUs
PM: sleep: Refine error message in try_to_freeze_tasks()
PM: sleep: Avoid using pr_cont() in the tasks freezing code
PM: runtime: Relocate rpm_callback() right after __rpm_callback()
PM: runtime: Do not call __rpm_callback() from rpm_idle()
PM / devfreq: event: use devm_platform_get_and_ioremap_resource()
PM / devfreq: event: Use device_match_of_node()
PM / devfreq: Use device_match_of_node()
powercap: idle_inject: Fix warnings with make W=1
PM: hibernate: Complain about memory map mismatches during resume
dt-bindings: cpufreq: cpufreq-qcom-hw: Add QDU1000/QRU1000 cpufreq
cpufreq: tegra186: Use flexible array to simplify memory allocation
cpupower: rapl monitor - shows the used power consumption in uj for each rapl domain
cpupower: Introduce powercap intel-rapl library and powercap-info command
cpupower: Add Georgian translation
cpufreq: intel_pstate: Add Sapphire Rapids support in no-HWP mode
cpufreq: amd_freq_sensitivity: Add missing pci_dev_put()
...
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"The devicetree changes contain exactly 1000 non-merge changesets,
including a number of new arm64 SoC variants from Qualcomm and Apple,
as well as the Renesas r9a07g043f/u chip in both arm64 and riscv
variants.
While we have occasionally merged support for non-arm SoCs in the
past, this is now the normal path for riscv devicetree files.
The most notable changes, by SoC platform, are:
- The Apple T6000 (M1 Pro), T6001 (M1 Max) and T6002 (M1 Ultra) chips
now have initial support. This is particularly nice as I am typing
this on a T6002 Mac Studio with only a small number of driver
patches.
- Qualcomm MSM8996 Pro (Snapdragon 821), SM6115 (Snapdragon 662),
SM4250 (Snapdragon 460), SM6375 (Snapdragon 695), SDM670
(Snapdragon 670), MSM8976 (Snapdragon 652) and MSM8956 (Snapdragon
650) are all mobile phone chips that are closely related to others
we already support.
Adding those helps support more phones and we add several models
from Sony (Xperia 10 IV, 5 IV, X, and X compact), OnePlus (One, 3,
3T, and Nord N100), Xiaomi (Poco F1, Mi6), Huawei (Watch) and
Google (Pixel 3a).
There are also new variants of the Herobrine and Trogdor chromebook
motherboards. SA8540P is an automotive SoC used in the Qdrive-3
development platform
- Rockchips gains no new SoC variants, but a lot of new boards: three
mobile gaming systems based on RK3326 Odroid-Go/rg351 family, two
more Anbernic gaming systems based on RK3566 and a number of other
RK356x based single-board computers.
- Renesas RZ/G2UL (r9a07g043) was already supported for arm64, but as
the newly added RZ/Five is based on the same design, this now gets
reorganized in order to share most of the dts description between
the two and add the RZ/Five SMARC EVK board support.
Aside from that, there are the usual changes all over the tree:
- New boards on other platforms contain two ASpeed BMC users, two
Broadcom based Wifi routers, Zyxel NSA310S NAS, the i.MX6 based
Kobo Aura2 ebook reader, two i.MX8 based development boards, two
Uniphier Pro5 development boards, the STM32MP1 testbench board from
DHCOR, the TI K3 based BeagleBone AI-64 board, and the Mediatek
Helio X10 based Sony Xperia M5 phone.
- The Starfive JH7100 source gets reorganized in order to support the
VisionFive V1 board.
- Minor updates and cleanups for Intel SoCFPGA, Marvell PXA168, TI,
ST, NXP, Apple, Broadcom, Juno, Marvell MVEBU, at91, nuvoton,
Tegra, Mediatek, Renesas, Hisilicon, Allwinner, Samsung, ux500,
spear, ... The treewide cleanups now have a lot of fixes for cache
nodes and other binding violoations.
- Somewhat larger sets of reworks for NVIDIA Tegra, Qualcomm and
Renesas platforms, adding a lot more on-chip device support
- A rework of the way that DTB overlays are built"
* tag 'soc-dt-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (979 commits)
arm64: dts: apple: t6002: Fix GPU power domains
arm64: dts: apple: t600x-pmgr: Fix search & replace typo
arm64: dts: apple: Add t8103 L1/L2 cache properties and nodes
arm64: dts: apple: Rename dart-sio* to sio-dart*
arch: arm64: apple: t600x: Use standard "iommu" node name
arch: arm64: apple: t8103: Use standard "iommu" node name
ARM: dts: socfpga: Fix pca9548 i2c-mux node name
dt-bindings: iio: adc: qcom,spmi-vadc: fix PM8350 define
dt-bindings: iio: adc: qcom,spmi-vadc: extend example
arm64: dts: qcom: sc8280xp: fix UFS DMA coherency
arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie
arm64: dts: qcom: sm8250-sony-xperia-edo: fix no-mmc property for SDHCI
arm64: dts: qcom: sdm845-sony-xperia-tama: fix no-mmc property for SDHCI
arm64: dts: qcom: sda660-inforce-ifc6560: fix no-mmc property for SDHCI
arm64: dts: qcom: sa8155p-adp: fix no-mmc property for SDHCI
arm64: dts: qcom: qrb5165-rb: fix no-mmc property for SDHCI
arm64: dts: qcom: sm8450: align MMC node names with dtschema
arm64: dts: qcom: sc7180-trogdor: use generic node names
arm64: dts: qcom: sm8450-hdk: add sound support
arm64: dts: qcom: sm8450: add Soundwire and LPASS
...
|
|
Merge cpufreq changes for 6.2-rc1:
- Generalize of_perf_domain_get_sharing_cpumask phandle format (Hector
Martin).
- Add new cpufreq driver for Apple SoC CPU P-states (Hector Martin).
- Update Qualcomm cpufreq driver, including:
* CPU clock provider support,
* Generic cleanups or reorganization.
* Potential memleak fix.
* Fix of the return value of cpufreq_driver->get().
(Manivannan Sadhasivam, Chen Hui).
- Update Qualcomm cpufreq driver's DT bindings, including:
* Support for CPU clock provider.
* Missing cache-related properties fixes.
* Support for QDU1000/QRU1000.
(Manivannan Sadhasivam, Rob Herring, Melody Olvera).
- Add support for ti,am625 SoC and enable build of ti-cpufreq for
ARCH_K3 (Dave Gerlach, and Vibhore Vardhan).
- Use flexible array to simplify memory allocation in the tegra186
cpufreq driver (Christophe JAILLET).
- Convert cpufreq statistics code to use sysfs_emit_at() (ye xingchen).
- Allow intel_pstate to use no-HWP mode on Sapphire Rapids (Giovanni
Gherdovich).
- Add missing pci_dev_put() to the amd_freq_sensitivity cpufreq driver
(Xiongfeng Wang).
- Initialize the kobj_unregister completion before calling
kobject_init_and_add() in the cpufreq core code (Yongqiang Liu).
- Defer setting boost MSRs in the ACPI cpufreq driver (Stuart Hayes,
Nathan Chancellor).
- Make intel_pstate accept initial EPP value of 0x80 (Srinivas
Pandruvada).
- Make read-only array sys_clk_src in the SPEAr cpufreq driver static
(Colin Ian King).
- Make array speeds in the longhaul cpufreq driver static (Colin Ian
King).
- Use str_enabled_disabled() helper in the ACPI cpufreq driver (Andy
Shevchenko).
- Drop a reference to CVS from cpufreq documentation (Conghui Wang).
* pm-cpufreq: (30 commits)
cpufreq: Remove CVS version control contents from documentation
cpufreq: stats: Convert to use sysfs_emit_at() API
cpufreq: ACPI: Only set boost MSRs on supported CPUs
dt-bindings: cpufreq: cpufreq-qcom-hw: Add QDU1000/QRU1000 cpufreq
cpufreq: tegra186: Use flexible array to simplify memory allocation
cpufreq: intel_pstate: Add Sapphire Rapids support in no-HWP mode
cpufreq: amd_freq_sensitivity: Add missing pci_dev_put()
cpufreq: Init completion before kobject_init_and_add()
cpufreq: apple-soc: Add new driver to control Apple SoC CPU P-states
cpufreq: qcom-hw: Add CPU clock provider support
dt-bindings: cpufreq: cpufreq-qcom-hw: Add cpufreq clock provider
cpufreq: qcom-hw: Fix the frequency returned by cpufreq_driver->get()
cpufreq: ACPI: Remove unused variables 'acpi_cpufreq_online' and 'ret'
cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
arm64: dts: ti: k3-am625-sk: Add 1.4GHz OPP
cpufreq: ti: Enable ti-cpufreq for ARCH_K3
arm64: dts: ti: k3-am625: Introduce operating-points table
cpufreq: dt-platdev: Blacklist ti,am625 SoC
cpufreq: ti-cpufreq: Add support for AM625
dt-bindings: cpufreq: qcom: Add missing cache related properties
...
|
|
soc/dt
Apple SoC DT updates for 6.2 (v3).
One final update for 6.2. This includes:
* L1/L2 cache topology for t8103
* A bunch of typo, style, and minor functional fixes
* tag 'asahi-soc-dt-6.2-v3' of https://github.com/AsahiLinux/linux:
arm64: dts: apple: t6002: Fix GPU power domains
arm64: dts: apple: t600x-pmgr: Fix search & replace typo
arm64: dts: apple: Add t8103 L1/L2 cache properties and nodes
arm64: dts: apple: Rename dart-sio* to sio-dart*
arch: arm64: apple: t600x: Use standard "iommu" node name
arch: arm64: apple: t8103: Use standard "iommu" node name
Link: https://lore.kernel.org/r/488ad4e9-04dc-1774-3bbe-d313ef30f14d@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On t6002 (M1 Ultra), each die contains a self-contained GPU block.
However, only the coprocessor and global management circuitry of the
first die are used. This is what is represented by the "gpu" PS (the
one in die1 is disabled). Nonetheless, this shared component drives the
processing blocks in both dies, and therefore depends on the AFR fabric
being powered up on both dies.
Add an explicit dependency from the GPU block on die0 to AFR on die1,
next to the existing die0 AFR dependency.
Fixes: fa86294eb355 ("arm64: dts: apple: Add initial t6000/t6001/t6002 DTs")
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
It looks like the search-and-replace that happened to add die IDs to
the t600x PMGR tree was a little bit too eager on a comment, and nobody
noticed! Let's fix that.
Fixes: fa86294eb355 ("arm64: dts: apple: Add initial t6000/t6001/t6002 DTs")
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
More Qualcomm ARM64 DT updates for 6.2
This introduce description of MSM8956 and MSM8976 and based on this adds
Sony Xperia X and X Compact.
It adds the SA8540P QDrive 3 automotive development board and enables
PCIe on the same.
Add description of the Vision Mezzanine for the RB5 board and the
Navigation Mezzanine for the SDM845 RB3.
SC8280XP adds L3 and DDR scaling support, resulting in good performance
improvement. PCIe and UFS is marked DMA coherent, resolving data
corruption issues. Reference clocks for UFS phy and device are
corrected, to resolve issues seen in combinations with some bootloaders
where it's not sufficient to rely on the bootloader state.
RTC description is added to the SA8295P ADP board.
For SM6115 GPI, PRNG, tsens, WCN, cpufreq, I2C/SPI and display blocks
are added.
On SM6375 QUP blocks are described, allowing the addition of touchscreen
and remoteprocs for ADSP and CDSP are introduced. Sony Xperia 10 IV
adds description of regulators, allowing enabling SD-card support.
SM8250 Coresight components are described
It introduces support for the Xiaomi Mi 6 on MSM8998 and adds flash LED
to the Xiaomi Redmi 2.
The SDHCI block on SM8350 is described and enabled on Sony Xperia 5 III.
SM8450 sound and Soundwire blocks are described, and enabled on HDK.
CPU supply clock is described, to satisfy the DT binding and the
opp-framework.
Sony Xperia 5 IV support is added, with touchscreen added.
Lastly a range of changes to align DT source with their bindings.
* tag 'qcom-arm64-for-6.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (98 commits)
dt-bindings: iio: adc: qcom,spmi-vadc: fix PM8350 define
dt-bindings: iio: adc: qcom,spmi-vadc: extend example
arm64: dts: qcom: sc8280xp: fix UFS DMA coherency
arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie
arm64: dts: qcom: sm8250-sony-xperia-edo: fix no-mmc property for SDHCI
arm64: dts: qcom: sdm845-sony-xperia-tama: fix no-mmc property for SDHCI
arm64: dts: qcom: sda660-inforce-ifc6560: fix no-mmc property for SDHCI
arm64: dts: qcom: sa8155p-adp: fix no-mmc property for SDHCI
arm64: dts: qcom: qrb5165-rb: fix no-mmc property for SDHCI
arm64: dts: qcom: sm8450: align MMC node names with dtschema
arm64: dts: qcom: sc7180-trogdor: use generic node names
arm64: dts: qcom: sm8450-hdk: add sound support
arm64: dts: qcom: sm8450: add Soundwire and LPASS
arm64: dts: qcom: sm8450: add GPR node
arm64: dts: qcom: sa8540p-ride: enable PCIe support
arm64: dts: qcom: sm6115: Add smmu fallback to qcom generic compatible
arm64: dts: qcom: sm6115: Add WCN node
arm64: dts: qcom: sm6115: Add i2c/spi nodes
arm64: dts: qcom: sm6115: Add GPI DMA
arm64: dts: qcom: sm6115: Add mdss/dpu node
...
Link: https://lore.kernel.org/r/20221207152554.3232434-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt
SoCFPGA dts updates for v6.2, part 2
- Fix dtschema for LED node
- Fix dtschema for i2c-mux
* tag 'socfpga_dts_updates_for_v6.2_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Fix pca9548 i2c-mux node name
ARM: dts: socfpga: align LED node names with dtschema
arm64: dts: altera: align LED node names with dtschema
Link: https://lore.kernel.org/r/20221206214006.590562-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The t8103 CPU nodes are missing the cache hierarchy information. The
cache hierarchy on Arm can not be detected and needs to be described in
DT. The OS scheduler can make use of this information for scheduling
decisions.
The cache size information is based on various articles about the
processors. There's also an L3 system level cache (SLC). It's not
described here because SLCs typically have some MMIO interface which
would need to be described.
Based on Rob Herring's patch adding cache properties and nodes for
t600x.
Link: https://lore.kernel.org/asahi/20221122220619.659174-1-robh@kernel.org/
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
All the other DARTs are named foo-dart, so let's keep things consistent.
Fixes: 51979fbb7fb8 ("arm64: dts: apple: t600x: Add MCA and its support")
Fixes: 8a3df85ad87d ("arm64: dts: apple: t8103: Add MCA and its support")
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
The PCIe iommu nodes use "dart" as node names. Replace it with the
the standard "iommu" node name as all other iommu nodes.
Fixes: 7b0b0191a2c7 ("arm64: dts: apple: Add initial t6000/t6001/t6002 DTs")
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
The PCIe iommu nodes use "dart" as node names. Replace it with the
the standard "iommu" node name as all other iommu nodes.
Fixes: 3c866bb79577 ("arm64: dts: apple: t8103: Add PCIe DARTs")
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
|
|
The SC8280XP UFS controllers are cache coherent and must be marked as
such in the devicetree to avoid potential data corruption.
Fixes: 152d1faf1e2f ("arm64: dts: qcom: add SC8280XP platform")
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221205100837.29212-3-johan+linaro@kernel.org
|
|
Add DT for sc7280-herobrine-zombie
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Owen Yang <ecs.taipeikernel@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221205133603.v15.2.I80aa32497bfd67bc8a372c1418ccc443ccf193e4@changeid
|
|
There is no "no-emmc" property, so intention for SD/SDIO only nodes was
to use "no-mmc":
qcom/sm8250-sony-xperia-edo-pdx206.dtb: mmc@8804000: Unevaluated properties are not allowed ('no-emmc' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204094438.73288-6-krzysztof.kozlowski@linaro.org
|
|
There is no "no-emmc" property, so intention for SD/SDIO only nodes was
to use "no-mmc":
qcom/sdm845-sony-xperia-tama-akatsuki.dtb: mmc@8804000: Unevaluated properties are not allowed ('no-emmc' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204094438.73288-5-krzysztof.kozlowski@linaro.org
|
