Age | Commit message (Collapse) | Author | Files | Lines |
|
For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
|
|
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
vexpress fixes for v4.5
Couple of minor fixes for vexpress platforms:
1. Add missing of_node_put in vexpress config bus
2. Add missing DMA-330 abort interrupt on Juno platforms
* tag 'vexpress-for-v4.5/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The DMA-330 has an "irq_abort" interrupt line on which it signals faults
separately from the "irq[n:0]" channel interrupts. On Juno, this is
wired up to SPI 92; add it to the DT so that DMAC faults are correctly
reported for the driver to reset the thing, rather than leaving it
locked up and waiting to time out.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
|
|
This patch replace the assoication between dsaf and enet from string
matching to object reference. It requires the DTS to be updated within
BIOS. Thanks god it can be done for all released boards.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
|
|
Pull networking fixes from David Miller:
"A quick set of bug fixes after there initial networking merge:
1) Netlink multicast group storage allocator only was tested with
nr_groups equal to 1, make it work for other values too. From
Matti Vaittinen.
2) Check build_skb() return value in macb and hip04_eth drivers, from
Weidong Wang.
3) Don't leak x25_asy on x25_asy_open() failure.
4) More DMA map/unmap fixes in 3c59x from Neil Horman.
5) Don't clobber IP skb control block during GSO segmentation, from
Konstantin Khlebnikov.
6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.
7) Fix SKB segment utilization estimation in xen-netback, from David
Vrabel.
8) Fix lockdep splat in bridge addrlist handling, from Nikolay
Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
bgmac: Fix reversed test of build_skb() return value.
bridge: fix lockdep addr_list_lock false positive splat
net: smsc: Add support h8300
xen-netback: free queues after freeing the net device
xen-netback: delete NAPI instance when queue fails to initialize
xen-netback: use skb to determine number of required guest Rx requests
net: sctp: Move sequence start handling into sctp_transport_get_idx()
ipv6: update skb->csum when CE mark is propagated
net: phy: turn carrier off on phy attach
net: macb: clear interrupts when disabling them
sctp: support to lookup with ep+paddr in transport rhashtable
net: hns: fixes no syscon error when init mdio
dts: hisi: fixes no syscon fault when init mdio
net: preserve IP control block during GSO segmentation
fsl/fman: Delete one function call "put_device" in dtsec_config()
hip04_eth: fix missing error handle for build_skb failed
3c59x: fix another page map/single unmap imbalance
3c59x: balance page maps and unmaps
x25_asy: Free x25_asy on x25_asy_open() failure.
mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
...
|
|
When linux start up, we get the log below:
"Hi-HNS_MDIO 803c0000.mdio: no syscon hisilicon,peri-c-subctrl
mdio_bus mdio@803c0000: mdio sys ctl reg has not maped"
The source code about the subctrl is dealt syscon, but dts doesn't.
It cause such fault, so this patch adds the syscon info on dts files to
fixes it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://github.com/AppliedMicro/xgene-next into next/dt64
Merge "Fixes for X-Gene DTS for v4.5" from Duc Dang:
This patch set fixes the node names of X-Gene I2C, GPIO
controller DT nodes; and also removes I2C clock nodes as
the same clock is shared between 2 I2C controllers
on X-Gene SoC.
* tag 'xgene-dts-fixes-for-v4.5' of https://github.com/AppliedMicro/xgene-next:
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
|
|
This patch updates the LS2080a DTSI (DTS Include) file to add
support for eight SP805 Watchdog units which can be used to
reset the eight Cortex-A57 cores available on LS2080A.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
X-Gene v2 I2C0 and I2C1 controllers share the same clock
enable register field. This patch remove clock node for I2C1
and leave I2C1 clock always on as having it toggled on/off
will affect I2C0 operation.
Signed-off-by: Duc Dang <dhdang@apm.com>
|
|
X-Gene v1 I2C0 and I2C1 controllers share the same clock
enable register field. This patch remove clock node for I2C0
and leave I2C0 clock always on as having it toggled on/off
will affect I2C1 operation.
Signed-off-by: Duc Dang <dhdang@apm.com>
|
|
platforms
Use devicetree standard node name for I2C (i2c@...),
GFC GPIO (gpio@...), DW GPIO (gpio@...), Standby GPIO (gpio@...).
The DT node name of USB (dwusb@...) still needs to be kept to
maintain backward compatibility with old firmware.
Signed-off-by: Duc Dang <dhdang@apm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
New node for the broadcast-timer of the rk3368, a non-critical fix for
a regulator voltage and a typo fix.
* tag 'v4.5-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add the broadcast-timer for RK3368 SoC
arm64: dts: rockchip: Fix typo in rk3368 sdmmc card detect pin name
arm64: dts: rockchip: correct voltage range for rk3368-evb-act8846 board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/dt64
Update psci support to the arm,psci-1.0 to mt8173
Add display PWM driver to mt8173
Add mediatek general porpose timer to mt8173
* tag 'v4.4-next-arm64' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mediatek: mt8173 PSCI-1.0 support
arm64: dts: mt8173: add MT8173 display PWM driver support node
arm64: dts: mt8173: add timer node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Third Round of Renesas ARM64 Based SoC DT Updates for v4.5
* Enable SATA
* Add salvator-x part number to DT bindings documentation
* Enable all four A57 cores instead of just one
* Enhanced audio support:
- Use CS2000 as AUDIO_CLK_B
- Set ak4613 In/Out pin as single-end
* tag 'renesas-arm64-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
arm64: dts: r8a7795: Add Cortex-A57 CPU cores
arm64: dts: r8a7795: Add PSCI node
arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B
arm64: renesas: salvator-x: set ak4613 In/Out pin as single-end
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Qualcomm ARM64 Updates for v4.5
* Add fixed rate oscillators to dts
* Fixup PMIC alias and properties
* Change 8916-MTP compatible to be compliant with new scheme
* Fix 8x16 UART pinctrl configuration
* Add SMEM, RPM/SMD, and PM8916 support on MSM8916
* tag 'qcom-arm64-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: Add PM8916 support on MSM8916
arm64: dts: qcom: Add RPM/SMD support on MSM8916
arm64: dts: qcom: Add MSM8916 SMEM nodes
arm64: dts: set the default i2c pin drive strength to 16mA
arm64: dts: fix the i2c aliasing to match to schematics.
arm64: dts: qcom: msm8916: Add fixed rate on-board oscillators
arm64: dts: qcom: Alias pm8916 on msm8916 devices
arm64: dts: qcom: Make msm8916-mtp compatible string compliant
arm64: dts: qcom: 8x16: UART1 and UART2 use DMA for RX and TX
arm64: dts: qcom: 8x16: UART1 add CTS_N, RTS_N pin configurations
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/dt64
arm: Xilinx ZynqMP dt patches for v4.5
- Label GPIO controller as interrupt controller
* tag 'zynqmp-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx:
ARM64: zynqmp: DT: Add interrupt-controller property to GPIO
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add label properties to provide a way to identify UARTs based on their
board or connector name. This follows naming convention in 96boards CE
spec. Ports without external connections are not labelled.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add label properties to provide a way to identify UART, I2C and SPI
ports based on their connector names. This follows naming convention in
96boards CE spec. Ports without external connections are not labelled.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The LS UART0 is not used by anything else and should be enabled for
expansion boards.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds idle-states bindings data collected through a set of
benchmarking experiments (latency and energy consumption) on Juno
boards. Latencies data represents the worst case scenarios as required
by the DT idle-states bindings.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Added sys-reboot node to the FSL's LS2080A SoC DT to leverage
the ARM-generic reboot mechanism for this SoC. This mechanism
is enabled through CONFIG_POWER_RESET_SYSCON.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Wenbin Song <Wenbin.Song@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
LS1043a is an SoC with 4 ARMv8 A53 cores and most other IP blocks are
similar to LS1021a which also complies to Freescale Chassis 2.1 spec.
Created LS1043a SoC DTSI file to be included by board level DTS files.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Wenbin Song <Wenbin.Song@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Samsung DeviceTree ARM64 updates and improvements for 4.5:
1. Add S2MPS15 PMIC node to Espresso board. This gives proper
control over regulators, provides 32KHz clocks and RTC driver.
2. Enable HS200 mode operation on Espresso board for MMC0.
3. Add reboot capability (generic syscon-reboot).
* tag 'samsung-dt64-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: Add reboot node for exynos7
arm64: dts: Enable HS200 mode operation on exynos7-espresso
arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This is the first ARMv8 SoC from Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
SATA clock is 815, not 915.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This enables SATA device in r8a7795-salvator-x.dts.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This adds SATA device node to r8a7795.dtsi.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
[uli: adjusted for new MSTP clock scheme]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enabling the performance monitor unit on r8a7795.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add Cortex-A57 CPU cores to r8a7795 SoC for a total of 4 x Cortex-A57.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Sigend-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add PSCI node for r8a7795 SoC, and cpu node enable-method property is
set to "psci".
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds the PM8916 regulator nodes found on MSM8916 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
|
|
Add support for the SMD and RPM devices found on MSM8916 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
|
|
This patch adds the nodes necessary to support the SMEM driver on MSM8916
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
|
|
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices connected on the other side
of level shifters on Linaro sensor board. Maxing up to 16mA made i2c much stable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch fixes the i2c bus number aliasing so that it matches with the
schematics bus naming.
Without this patch the user might would get bus numbers depending on
the order the devices are probed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
|
|
Add an alias for pm8916 on msm8916 based SoCs so that the newly
updated dtbTool can find the pmic compatible string and add the
pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
|
|
This compatible string isn't compliant with the format for
subtypes. Replace it with a compliant compatible type.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
|
|
GPIO can be used as interrupt-controller. Add the missing properties to
the GPIO node.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a need of a broadcast timer in this case to ensure proper
wakeup when the cpus are in sleep mode and a timer expires.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|