| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-03-02
Here's one more bluetooth-next pull request for the 5.1 kernel:
- Added support for MediaTek MT7663U and MT7668U UART devices
- Cleanups & fixes to the hci_qca driver
- Fixed wakeup pin behavior for QCA6174A controller
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RDB board
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we don't coordinate BT USB activity with our handling of the
BT out-of-band wake pin, and instead just use gpio-keys. That causes
problems because we have no way of distinguishing wake activity due to a
BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
mask before suspend). This can cause spurious wake events just because
we, for instance, try to reconfigure the host controller's event mask
before suspending.
We can avoid these synchronization problems by handling the BT wake pin
directly in the btusb driver -- for all activity up until BT controller
suspend(), we simply listen to normal USB activity (e.g., to know the
difference between device and host activity); once we're really ready to
suspend the host controller, there should be no more host activity, and
only *then* do we unmask the GPIO interrupt.
This is already supported by btusb; we just need to describe the wake
pin in the right node.
We list 2 compatible properties, since both PID/VID pairs show up on
Scarlet devices, and they're both essentially identical QCA6174A-based
modules.
Also note that the polarity was wrong before: Qualcomm implemented WAKE
as active high, not active low. We only got away with this because
gpio-keys always reconfigured us as bi-directional edge-triggered.
Finally, we have an external pull-up and a level-shifter on this line
(we didn't notice Qualcomm's polarity in the initial design), so we
can't do pull-down. Switch to pull-none.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
arm/fixes
mvebu fixes for 5.0 (part 2)
Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release
* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PHY reset signal goes to mpp43 on CP0.
Fixes: babc5544c293 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Reported-by: Denis Odintsov <oversun@me.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0, 3rd round:
It contains a fix for i.MX8MQ EVK board device tree, which makes the
broken eMMC support work as expected.
* tag 'imx-fixes-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq: Fix boot from eMMC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fix for new dtc graph warnings and a regulator fix for rock64.
* tag 'v5.0-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable usb-host regulators at boot on rk3328-rock64
arm64: dts: rockchip: fix graph_port warning on rk3399 bob kevin and excavator
|
|
The boot from eMMC is currently broken on the NXP i.MX8MQ EVK board.
When trying to boot from eMMC it fails with:
...
[ 1.271938] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.287429] print_req_error: I/O error, dev mmcblk1, sector 1 flags 0
[ 1.306833] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.322325] print_req_error: I/O error, dev mmcblk1, sector 2 flags 0
[ 1.329559] Buffer I/O error on dev mmcblk1, logical block 0, async page read
[ 1.336714] mmcblk1: unable to read partition table
...
The problem is the result of a partial misconfiguration of the pins and
the missing assigned clock rate.
Fixes: 9079aca4aacd ("arm64: add support for i.MX8M EVK board")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/fixes
Qualcomm ARM64 Fixes for 5.0-rc3
* Fix irq controller compatible for the MSM8996 platforms
* tag 'qcom-fixes-for-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: add msm8996 compatible to gicv3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Second Round of Renesas ARM Based SoC Fixes for v5.0
Enable DMA for SCIF2 on R-Car M3-W (r8a7796) and M3-n (r8a77965), and
(RZ/G2M) r8a774a1 SoCs.
This is was omitted from patches enabling DMA for other SCIF devices on the
same SoCs due to missing documentation. However, it is regarded as a fix
as arguably those patches claim to add this feature.
Per-SoC patches are provided to ease backporting of this fix as the kernel
version to be fixed is different for each SoC.
* tag 'renesas-fixes2-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
After commit ef05bcb60c1a, boot from USB drives is broken.
Fix this problem by enabling usb-host regulators during boot time.
Fixes: ef05bcb60c1a ("arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Voytik <voytikd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Ports are described by child 'port' nodes contained in the device node.
'ports' is optional and is used to group all 'port' nodes which is not
the case here.
This patch fixes the following warnings:
arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts:25.9-29.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts:46.9-50.5: Warningi (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts:94.9-98.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
SCIF2 on R-Car M3-N can be used with both DMAC1 and DMAC2.
Fixes: 0ea5b2fd38db56aa ("arm64: dts: renesas: r8a77965: Add SCIF device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
SCIF2 on R-Car M3-W can be used with both DMAC1 and DMAC2.
Fixes: dbcae5ea4bd27409 ("arm64: dts: r8a7796: Enable SCIF DMA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
SCIF2 on RZ/G2M can be used with both DMAC1 and DMAC2.
Fixes: 3a3933a4fa36430a ("arm64: dts: renesas: r8a774a1: Add SCIF and HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
changed the behavior of "cd-inverted" to follow the device tree bindings
specification:
According to SDHCI standard, CD lines are specified as "active low".
Using the "cd-inverted" property means that the CD line is "active high".
Fix the SD card description for meson by setting the cd-gpios as
"active low", according to the boards specifications, and dropping the
"cd-inverted" property.
Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The MPP52 signal is on the seconds GPIO instance of CP0, which
corresponds to the &cp0_gpio2 handle.
Rename the property name to the standard '-gpios' suffix while at it.
Fixes: b83e1669adce6 ("arm64: dts: marvell: mcbin: add support for PCIe")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from Linux leads to an immediate crash.
So let's make the same memory reservation as the vendor kernel.
[gregory: added as comment that this region matches the mainline U-boot]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f9151 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
When introducing the video-codec node for the video engine, the
compatible for the H5 was used instead of the compatible for the
A64. Use the right compatible instead.
Fixes: d60ce24740d2 ("arm64: dts: allwinner: a64: Add Video Engine node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM64 changes for v4.21, part 2
Add IMEM clock controller (for Security SubSystem) and Bluetooth chip to
Exynos5433 TM2(e) boards.
* tag 'samsung-dt64-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: exynos: Add IMEM clock controller to Exynos5433
arm64: dts: exynos: Add all CPUs in cooling maps
arm64: dts: exynos: Update DWC3 modules on Exynos5433 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/late
i.MX8MQ device tree support for 4.21:
- It contains the initial device tree support for i.MX8MQ - the first
ARM64 i.MX processor. It features a quad Cortex-A53 core that
operates at speeds of up to 1.3 GHz, a Cortex-M4 core for
low-power processing, a DRAM controller that supports 32-bit/16-bit
LPDDR4/DDR4/DDR3L memory, and hardware acceleration for 4K video
playback.
- A couple of patches from Baruch that add watchdog device for i.MX8MQ
enable it for imx8mq-evk board.
* tag 'imx8mq-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
arm64: add basic Kconfig symbols for i.MX8
arm64: dts: ls1046a: add qdma device tree nodes
arm64: dts: ls1043a: add qdma device tree nodes
arm64: dts: ls1088a: Add missing dma-ranges property
arm64: dts: ls1088a: Move fsl-mc node
arm64: dts: fsl: Add all CPUs in cooling maps
arm64: dts: Add support for NXP LS1028A SoC
arm64: dts: layerscape: removed compatible string "snps,dw-pcie"
arm64: dts: fsl: Add the status property disable PCIe
arm64: dts: ls1012a: Add FRWY-LS1012A board support
dt-bindings: Add binding for i.MX8MQ CCM
arm64: dts: add LX2160AQDS board support
arm64: dts: add LX2160ARDB board support
arm64: dts: add QorIQ LX2160A SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC Fixes for v4.20
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
* tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: draak: Fix CVBS input
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21 - round 2
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
* tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into next/dt
AM65x DT changes for 4.21. Includes:
- Pinctrl support
- I2C support
- ECAP PWM support
- Power domain handling for UARTs
- McSPI support
* tag 'am654-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/dt
arm64: dts: zynqmp: DT changes for v5.0
- Fix node names
- Fix wakeup-source
- Wire ddrc
- Label gpio controller (PS gpio)
* tag 'zynqmp-dt-for-v5.0' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Fix node names which contain "_"
arm64: dts: zynqmp: Add missing gpio-controller to ps gpio
arm64: dts: zynqmp: Add DDRC node
arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source property
arm64: dts: zynqmp: Use mmc@ instead sdhci@
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO2 provides
overall power via VBAT, and DLDO4 provides I/O power via VDDIO. The RTC
clock output provides the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for Bluetooth,
but this is not covered here.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
TM2(e) boards have a Broadcom Bluetooth chip connected to 3rd UART port.
Add a device tree node describing it and its resources (control GPIO lines
and clock).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The external nWDOG signal connects to the EVK board reset circuit.
Tested on the i.MX8MQ EVK rev B3.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is the evaluation kit board for the i.MX8M. The current level of
support yields a working console and is able to boot userspace from
SD card or Network.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> (v1)
Reviewed-by: Rob Herring <robh@kernel.org> (v3)
Tested-by: Tested-by: Baruch Siach <baruch@tkos.co.il> (v1)
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the basic DTS for the i.MX8MQ.
For now only the following peripherals are supported:
- IOMUXC (pin controller)
- CCM (clock controller)
- GPIO
- UART
- uSDHC (SD/eMMC controller)
- FEC (ethernet controller)
- i2c
This is enough to get a very basic board support up and running.
One known limitation is that the driver for the GPC interrupt
controller is still missing, rendering the CPU sleep states unusable
as there is nothing waking them up anymore.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The properties 'num-cs' and 'bus-num' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable McSPI0 of main domain and add DT node for the SPI NOR flash
connected to CS0.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
There are 3 instances of McSPI in MCU domain and 4 instances in Main domain.
Add DT nodes for all McSPI instances present on AM654 SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Populate power-domain property for UART nodes, this is required for
Linux to enable UART clocks via PM calls. Without this UART instances
not initialized by bootloader (like main_uart1) fails to work in Linux.
Also, drop current-speed property from main_uart1 and main_uart2 nodes
as these UARTs are not initialized before Linux boots up and current
speed is unknown.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Enable ECAP PWM which is used for LCD backlight.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add DT entry for ECAP0 PWM node present in main domain
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
