Age | Commit message (Collapse) | Author | Files | Lines |
|
Rockchip SoCs use 2 different numbering schemes. Where the gpio-
controllers just count 0-31 for their 32 gpios, the underlying
iomux controller splits these into 4 separate entities A-D.
Device-schematics always use these iomux-values to identify pins,
so to make mapping schematics to devicetree easier Andy Yan introduced
named constants for the pins but so far we only used them on new
additions.
Using a sed-script created by Emil Renner Berthing bulk-convert
the remaining raw gpio numbers into their descriptive counterparts
and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x
mappings:
/rockchip,pins *=/bcheck
b # to end of script
:append-next-line
N
:check
/^[^;]*$/bappend-next-line
s/<RK_GPIO\([0-9]\) /<\1 /g
s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g
s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g
s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g
s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g
s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g
s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g
s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g
s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g
s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g
s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g
s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g
s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g
s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g
s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g
s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g
s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g
s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g
s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g
s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g
s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g
s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g
s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g
s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g
s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g
s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g
s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g
s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g
s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g
s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g
s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g
s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g
s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g
s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g
s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g
Suggested-by: Emil Renner Berthing <esmil@mailme.dk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Acked-by: Robin Murphy <robin.murphy@arm.com>
|
|
Add on-board LED support for Ficus board based on the following
standard used by other 96Boards:
red:user1 default-trigger: heartbeat
red:user2 default-trigger: mmc0/disk-activity (onboard-storage)
red:user3 default-trigger: mmc1 (SD-card)
red:user4 default-trigger: none, panic-indicator
red:wlan default-trigger: phy0tx
red:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Since the same family members of Rock960 boards (Rock960 and Ficus)
share the same configuration, split out the common nodes into a common
dtsi file for reducing code duplication. The board specific nodes for
Ficus boards are then placed in corresponding board DTS file.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
Only the properties which differ between both boards are placed in the
board specific dts and the reset of the nodes are placed in common dtsi
file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The pwm-regulator for vdd_log uses additional unreviewed properties in the
vendor kernel, which slipped in with the devicetree.
As written, they are unreviewed and unused in all mainline implementations
so drop them again.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The vcc3v3_pcie regulator supplies 3.3V so add voltage properties
for it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[split off from original patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The board exposes two types A ports, one is USB 3.0, up to 5.0Gbps and
another one is USB 2.0 up to 480Mbps. Enable the USB PHYs and the USB
controllers to enable theses devices.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3399 Ficus board is an Enterprise Edition board
manufactured by Vamrs Ltd., based on the Rockchip RK3399 SoC.
The board exposes a bunch of nice peripherals, including
SATA, HDMI, MIPI CSI, Ethernet, WiFi, and PCIe.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|