| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add device tree nodes describing used i2c busses according to the dts
found in msm-4.19 tree.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200913224738.30046-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The UART12 node has been mistakenly mentioned as UART2. Let's fix that
for both SM8250 SoC and MTP board and also add pinctrl definition for
it.
Fixes: 60378f1a171e ("arm64: dts: qcom: sm8250: Add sm8250 dts file")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200904063637.28632-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
rather than as a regulator. As such it's available from the rpmhpd as
the SM8250_LCX power domain.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: ec13d5c23a33 ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
Link: https://lore.kernel.org/r/20200622222747.717306-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the TLMM pinctrl node for SM8250 and reserve pins 28-31 and 40-43 on
the MTP as firmware does not allow Linux to touch these pins.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200430181716.3797842-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Include files describing used PMIC chips, GPIOs, power on, etc nodes.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200621192824.2069145-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add nodes for the UFS controller and PHY, and enable these for the MTP
with relevant supplies specified.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200415061430.740854-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add RPMh controlled regulators for the three PMICs and specify voltage
ranges and mode for relevant regulators.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200415061430.740854-2-bjorn.andersson@linaro.org
[bjorn: Fixed up some supplies and voltages]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add sm8250 devicetree file for SM8250 SoC and SM8250 MTP platform.
This file adds the basic nodes like cpu, psci and other required
configuration for booting up to the serial console.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200310050910.506854-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
