| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The baseboard has support for a TDNext 5640 Camera which
uses an OV5640 connected to a 2-lane CSI2 interface.
With the CSI and mipi_csi2 drivers pointing to an OV5640 camera, the media
pipeline can be configured with the following:
media-ctl --links "'ov5640 1-003c':0->'imx7-mipi-csis.0':0[1]"
The camera and various nodes in the pipeline can be configured for UYVY:
media-ctl -v -V "'ov5640 1-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -v -V "'csi':0 [fmt:UYVY8_1X16/640x480 field:none]"
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8M Mini has two available USB controllers. On the
imx8mm-beacon board, USB1 is routed to a mini-USB port with
OTG functionality. USB2 is routed to a USB hub which has
three host-only ports connected to it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The wlf,wm8962 driver does not use the clock-names property.
Drop it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Device tree schema expects pin configuration groups to end with 'grp'
suffix. This fixes dtbs_check warnings like:
pinctrl@30330000: 'pcal6414-gpio', 'pmicirq', 'usdhc1grp100mhz', 'usdhc1grp200mhz', 'usdhc1grpgpio',
'usdhc2grp100mhz', 'usdhc2grp200mhz', 'usdhc2grpgpio', 'usdhc3grp100mhz', 'usdhc3grp200mhz'
do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no LED default state "none". leds-gpio driver maps it to
"off", so correct them to fix dtbs_check warnings like:
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dt.yaml:
leds: led0:default-state:0: 'none' is not one of ['on', 'off', 'keep']
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Beacon Embeddedworks is launching a development kit based on the
i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
+ baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard
has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
