| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Khadas VIM3 shares the eMMC pins 4 to 7 with the SPI NOR, in order
to enable the eMMC and the SPI NOR interface, we need to omit the
4 last pins from the eMMC pinctrl.
As it was done for the Khadas VIM2, split the eMMC pinctrls in ctrl, data
and ds pins with either 4bits data or 8bits data, and update the current
board accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-2-narmstrong@baylibre.com
|
|
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-x96max keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12a-x96-max.dt.yaml: /: compatible: ['amediatech,x96-max', 'amlogic,u200', 'amlogic,g12a'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
X96 Max has the PHY reset and interrupt lines are identical to the
Odroid-N2:
- GPIOZ_14 is the interrupt on X96 Max
- GPIOZ_15 is the reset line on X96 Max
Add GPIOZ_14 as PHY interrupt line on the X96 Max so we don't have to
poll for the PHY status.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Odroid-N2 schematics show that the following pins are used for the
reset and interrupt lines:
- GPIOZ_14 is the PHY interrupt line
- GPIOZ_15 is the PHY reset line
The GPIOZ_14 and GPIOZ_15 pins are special. The datasheet describes that
they are "3.3V input tolerant open drain (OD) output pins". This means
the GPIO controller can drive the output LOW to reset the PHY. To
release the reset it can only switch the pin to input mode. The output
cannot be driven HIGH for these pins.
This requires configuring the reset line as GPIO_OPEN_DRAIN because
otherwise the PHY will be stuck in "reset" state (because driving the
pin HIGH seems to result in the same signal as driving it LOW).
The reset line works together with a pull-up resistor (R143 in the
Odroid-N2 schematics). The SoC can drive GPIOZ_14 LOW to assert the PHY
reset. However, since the SoC can't drive the pin HIGH (to release the
reset) we switch the mode to INPUT and let the pull-up resistor take
care of driving the reset line HIGH.
Switch to GPIOZ_15 for the PHY reset line instead of using GPIOZ_14
(which actually is the interrupt line).
Move from the "snps" specific resets to the MDIO framework's
reset-gpios because only the latter honors the GPIO flags.
Use the GPIO flags (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN) to match with
the pull-up resistor because this will:
- drive the output LOW to reset the PHY (= active low)
- switch the pin to INPUT mode so the pull-up will take the PHY out of
reset
Fixes: 51d116557b2044 ("arm64: dts: meson-g12a-x96-max: Add Gigabit Ethernet Support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the sound card on the X96 Max, enabling HDMI output using the
TDM interface B, being aligned on other boards sound cards.
SPDI/F support is also enabled to the physical toslink port and to HDMI.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Setting to 2Mbaud/s is the nominal bus speed for common usages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The X96 Max embeds an AP6398S SDIO module, let's add the
corresponding SDIO, PWM clock and mmc-pwrseq nodes.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add nodes to support SDCard and onboard eMMC on the X96 Max.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the network interface of the X96 Mac using an external
Realtek RTL8211F gigabit PHY, needing the same broken-eee properties
as the previous Amlogic SoC generations.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add support for the IR decoder input on the X96 Max board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the X96 Max STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the USB2 and USB3 Host ports on the X96 Max Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the Bluetooth Module on the X96 Max Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add system regulators for the X96 Max Set-Top-Box.
Still missing
* VDD_EE (0.8V - PWM controlled)
* VDD_CPU (PWM controlled)
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the G12a (S905X2) based X96 Max board[1].
There is no branding for the manufacturer anywhere on the product, so it
took some digging[2] to find the manufacturer. But since there's
nothing about the maker on the product I've left it out of the DT name
because 1) nobody will know that name and 2) keeps the DT filename
shorter.
[1] https://www.cnx-software.com/2018/09/25/x96-max-amlogic-s905x2-tv-box/
[2] https://fccid.io/2AI6D-X96MAX
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
