summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-ux500
AgeCommit message (Collapse)AuthorFilesLines
2014-04-05Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds10-626/+0
Pull ARM SoC device tree changes from Arnd Bergmann: "A large part of the arm-soc patches are nowadays DT changes, adding support for new SoCs, boards and devices without changing kernel source. The plan is still to move the devicetree files out of the kernel tree and reduce the amount of churn going on here, but we keep finding reasons to delay doing that. Changes are really all over the place, with little sticking out particularly. We have contributions from a total of 116 people in this branch. Unfortunately, the size of this branch also causes a significant number of conflicts at the moment, typically when subsystem maintainers merge patches that change the driver at the same time as the dts files. In most cases this could be avoided because the dts changes are supposed to be compatible in both ways, and we are asking everyone to send ARM dts changes through our tree only" * tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits) dts: stmmac: Document the clocks property in the stmmac base document dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac. ARM: STi: stih41x: Add support for the FSM Serial Flash Controller ARM: STi: stih416: Add support for the FSM Serial Flash Controller ARM: tegra: fix Dalmore pinctrl configuration ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND ARM: dts: Build all keystone dt blobs ARM: dts: keystone: Fix control register range for clktsip ARM: dts: keystone: Fix domain register range for clkfftc1 ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap ARM: dts: bcm21664: Add device tree files. ARM: DT: bcm21664: Device tree bindings ARM: efm32: properly namespace i2c location property ARM: efm32: fix unit address part in USART2 device nodes' names ARM: mvebu: Enable NAND controller in Armada 385-DB ARM: mvebu: Add support for NAND controller in Armada 38x SoC ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs ...
2014-03-04mfd: dbx500/abx500: root out hardcoded IRQ assignmentsLinus Walleij5-234/+0
The DBx500 and ABx500 should be getting their IRQs from the device tree and nowhere else. Get rid of all the static assignments everywhere, delete it from the driver, platform data and the board files in one swift strike. Lots of cross-dependencies in the MFD drivers for PRCMU and AB8500 makes it necessary to strike everywhere at once to eradicate IRQs passed as resources and platform data to the left and right around the platform. Cc: Mark Brown <broonie@kernel.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-03-04ARM: ux500: drop a chunk of GPIO definitionsLinus Walleij1-69/+0
The Ux500 GPIOs are now assigned dynamically from the device tree. Drop this table of static assignments. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-28ARM: ux500: skip GIC CPU and dist address checksLinus Walleij1-10/+0
The Ux500 is initializing its IRQs from the device tree and does not need to figure out any static base addresses anymore, this is just dead code so delete it. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-28ARM: ux500: delete pointless DT config optionLinus Walleij2-8/+0
Supporting device tree on the Ux500 is not optional anymore, so delete the config option and compile this in at all times. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-19ARM: select MIGHT_HAVE_CACHE_L2X0 for V6 and V7 multi-platformRob Herring1-1/+0
Many V6 and V7 platforms have an L2x0 cache, so make CONFIG_MIGHT_HAVE_CACHE_L2X0 visible for V6 and V7 multi-platform builds. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
2014-02-19ARM: select HAVE_SMP for V7 multi-platformRob Herring1-1/+0
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7 multi-platform builds. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
2014-02-19ARM: centralize common multi-platform kconfig optionsRob Herring1-4/+0
Multi-platform requires various kconfig options to be selected, so platforms don't need to select them individually. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
2014-02-04ARM: ux500: move last AB8505 set-up to DTLinus Walleij4-99/+0
This moves the set-up of the HREF500 with its AB8505 ASIC to a device tree include. Since there is not yet any device tree for this board the DTSI is currently unused. After this delete the board file for pins for good and migration of pins to the device tree is complete. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 clock out pins to DTLinus Walleij3-50/+0
This moves the AB8500 pin settings for the clock out pins over to the device tree. We can delete the special setup calls for the platforms only using the AB8500 and not AB8505. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 modem I2C settings to DTLinus Walleij1-8/+0
This moves the pin setup of the AB8500 modem I2C pins (SCL/SDA) from the board file to the device tree. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 EXTCPENA from board file to DTLinus Walleij1-7/+0
This moves the configuration of the AB8500 EXTCPENA pin from the board file to the device tree. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 DMIC settings to DTLinus Walleij1-24/+0
This move the AB8500 DMIC (microphone) pin setup from the board file to the device tree. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 USB UICC settings to DTLinus Walleij1-9/+0
This moves the set-up of the USB UICC (InteChip USB) from the board file to the device tree. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 audio interface 1 settings to DTLinus Walleij1-10/+0
This moves the pin muxing and configuration for audio interface one over to the device tree as a hog configuration. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 PWM out settings to device treeLinus Walleij1-10/+0
This moves the muxing and biasing of the AB8500 PWM output pins over to the device tree for affected platforms. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 YCBCR settings to device treeLinus Walleij1-10/+0
This moves the pin control settings for the YCBCR connector on the AB8500 over to the device tree as a hog. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-02-04ARM: ux500: move AB8500 GPIOs to device treeLinus Walleij1-79/+0
Move the AB8500 muxing and biasing settings over from the board file to the device tree, include it in the reference designs using the AB8500: HREF prior to v60, v60plus and Snowball. Set up these GPIO lines using hogs, just like in the board file. Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-01-23Merge tag 'dt-for-linus' of ↵Linus Torvalds16-1094/+34
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC DT updates from Olof Johansson: "DT and DT-conversion-related changes for various ARM platforms. Most of these are to enable various devices on various boards, etc, and not necessarily worth enumerating. New boards and systems continue to come in as new devicetree files that don't require corresponding C changes any more, which is indicating that the system is starting to work fairly well. A few things worth pointing out: * ST Ericsson ux500 platforms have made the major push to move over to fully support the platform with DT * Renesas platforms continue their conversion over from legacy platform devices to DT-based for hardware description" * tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits) ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6 ARM: dts: sirf: add lost minigpsrtc device node ARM: dts: sirf: add clock, frequence-voltage table for CPU0 ARM: dts: sirf: add lost bus_width, clock and status for sdhci ARM: dts: sirf: add lost clocks for cphifbg ARM: dts: socfpga: add pl330 clock ARM: dts: socfpga: update L2 tag and data latency arm: sun7i: cubietruck: Enable the i2c controllers ARM: dts: add support for EXYNOS4412 based TINY4412 board ARM: dts: Add initial support for Arndale Octa board ARM: bcm2835: add USB controller to device tree ARM: dts: MSM8974: Add MMIO architected timer node ARM: dts: MSM8974: Add restart node ARM: dts: sun7i: external clock outputs ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style ARM: dts: sun7i: Add pin muxing options for clock outputs ARM: dts: sun7i: Add rtp controller node ARM: dts: sun5i: Add rtp controller node ARM: dts: sun4i: Add rtp controller node ...
2014-01-23Merge tag 'soc-for-linus' of ↵Linus Torvalds1-0/+27
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform changes from Olof Johansson: "New core SoC-specific changes. New platforms: * Introduction of a vendor, Hisilicon, and one of their SoCs with some random numerical product name. * Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU). * Marvell Berlin series of SoCs, which include the one in Chromecast. * MOXA platform support, ARM9-based platform used mostly in industrial products * Support for Freescale's i.MX50 SoC. Other work: * Renesas work for new platforms and drivers, and conversion over to more multiplatform-friendly device registration schemes. * SMP support for Allwinner sunxi platforms. * ... plus a bunch of other stuff across various platforms" * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits) ARM: tegra: fix tegra_powergate_sequence_power_up() inline ARM: msm_defconfig: Update for multi-platform ARM: msm: Move MSM's DT based hardware to multi-platform support ARM: msm: Only build timer.c if required ARM: msm: Only build clock.c on proc_comm based platforms ARM: ux500: Enable system suspend with WFI support ARM: ux500: turn on PRINTK_TIME in u8500_defconfig ARM: shmobile: r8a7790: Fix I2C controller names ARM: msm: Simplify ARCH_MSM_DT config ARM: msm: Add support for MSM8974 SoC ARM: sunxi: select ARM_PSCI MAINTAINERS: Update Allwinner sunXi maintainer files ARM: sunxi: Select RESET_CONTROLLER ARM: imx: improve the comment of CCM lpm SW workaround ARM: imx: improve status check of clock gate ARM: imx: add necessary interface for pfd ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100 ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support ARM: imx: Add cpu frequency scaling support ARM i.MX35: Add devicetree support. ...
2014-01-23Merge tag 'cleanup-for-linus' of ↵Linus Torvalds1-2/+1
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "This is the branch where we usually queue up cleanup efforts, moving drivers out of the architecture directory, header file restructuring, etc. Sometimes they tangle with new development so it's hard to keep it strictly to cleanups. Some of the things included in this branch are: * Atmel SAMA5 conversion to common clock * Reset framework conversion for tegra platforms - Some of this depends on tegra clock driver reworks that are shared with Mike Turquette's clk tree. * Tegra DMA refactoring, which are shared branches with the DMA tree. * Removal of some header files on exynos to prepare for multiplatform" * tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits) ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h ARM: mvebu: remove prototypes of non-existing functions from common.h ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h serial: sh-sci: Rework baud rate calculation serial: sh-sci: Compute overrun_bit without using baud rate algo serial: sh-sci: Remove unused GPIO request code serial: sh-sci: Move overrun_bit and error_mask fields out of pdata serial: sh-sci: Support resources passed through platform resources serial: sh-sci: Don't check IRQ in verify port operation serial: sh-sci: Set the UPF_FIXED_PORT flag serial: sh-sci: Remove duplicate interrupt check in verify port op serial: sh-sci: Simplify baud rate calculation algorithms serial: sh-sci: Remove baud rate calculation algorithm 5 serial: sh-sci: Sort headers alphabetically ARM: EXYNOS: Kill exynos_pm_late_initcall() ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4 ARM: at91: switch Calao QIL-A9260 board to DT clk: at91: fix pmc_clk_ids data type attriubte PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h> ARM: EXYNOS: remove <mach/regs-clock.h> for exynos ...
2014-01-23Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds1-1/+1
Pull ARM updates from Russell King: "In this set, we have: - Refactoring of some of the old StrongARM-1100 GPIO code to make things simpler by Dmitry Eremin-Solenikov - Read-only and non-executable support for modules on ARM from Laura Abbot - Removal of unnecessary set_drvdata() calls in AMBA code - Some non-executable support for kernel lowmem mappings at the 1MB section granularity, and dumping of kernel page tables via debugfs - Some improvements for the timer/clock code on Footbridge platforms, and cleanup some of the LED code there - Fix fls/ffs() signatures to match x86 to prevent build warnings, particularly where these are used with min/max() macros - Avoid using the bootmem allocator on ARM (patches from Santosh Shilimkar) - Various asid/unaligned access updates from Will Deacon" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (51 commits) ARM: SMP implementations are not supposed to return from smp_ops.cpu_die() ARM: ignore memory below PHYS_OFFSET Fix select-induced Kconfig warning for ZBOOT_ROM ARM: fix ffs/fls implementations to match x86 ARM: 7935/1: sa1100: collie: add gpio-keys configuration ARM: 7932/1: bcm: Add DEBUG_LL console support ARM: 7929/1: Remove duplicate SCHED_HRTICK config option ARM: 7928/1: kconfig: select HAVE_EFFICIENT_UNALIGNED_ACCESS for CPUv6+ && MMU ARM: 7927/1: dcache: select DCACHE_WORD_ACCESS for big-endian CPUs ARM: 7926/1: mm: flesh out and fix the comments in the ASID allocator ARM: 7925/1: mm: keep track of last ASID allocation to improve bitmap searching ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE ARM: PCI: add legacy IDE IRQ implementation ARM: footbridge: cleanup LEDs code ARM: pgd allocation: retry on failure ARM: footbridge: add one-shot mode for DC21285 timer ARM: footbridge: add sched_clock implementation ARM: 7922/1: l2x0: add Marvell Tauros3 support ARM: 7877/1: use built-in byte swap function ARM: 7921/1: mcpm: remove redundant dsb instructions prior to sev ...
2014-01-21Merge branches 'amba', 'fixes', 'kees', 'misc' and 'unstable/sa11x0' into ↵Russell King1-1/+1
for-next
2014-01-16Merge remote-tracking branches 'asoc/topic/adsp', 'asoc/topic/atmel', ↵Mark Brown1-4/+4
'asoc/topic/bcm2835', 'asoc/topic/docs', 'asoc/topic/fsl', 'asoc/topic/generic', 'asoc/topic/kirkwood', 'asoc/topic/mc13783', 'asoc/topic/mxs', 'asoc/topic/nuc900', 'asoc/topic/sai', 'asoc/topic/sh', 'asoc/topic/ssm2602', 'asoc/topic/tlv320aic3x', 'asoc/topic/twl4030', 'asoc/topic/ux500', 'asoc/topic/width' and 'asoc/topic/x86' into for-tiwai
2014-01-08Merge tag 'ux500-core-v3.14' of ↵Olof Johansson1-0/+27
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc From Linus Walleij: Ux500 core patches for the v3.14 series: - Enable PRINTK_TIME - Enable suspend with WFI * tag 'ux500-core-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: ux500: Enable system suspend with WFI support ARM: ux500: turn on PRINTK_TIME in u8500_defconfig Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-08Merge tag 'ux500-devicetree-v3.14-2' of ↵Olof Johansson3-19/+0
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt From Linus Walleij: Ux500 device tree patches for v3.14, take 2 - Delete some unused U8540 UART platform data. - MMC/SD-fixes from Ulf Hansson so everything works with the device tree again. * tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: ARM: ux500: regulators: Remove dead code for SD-card regulator ARM: ux500: Configure regulator for I/O voltage for SD-card slot ARM: ux500: Refactor common DT configs for sdi[n] devices ARM: ux500: delete U8540 UART auxdata Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-07ARM: ux500: Don't use enums for MSP IDs - for easy DT conversionLee Jones1-4/+4
Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-07ARM: ux500: Enable system suspend with WFI supportUlf Hansson1-0/+27
When building for CONFIG_SUSPEND, add the platform suspend callbacks to enable system suspend for ux500. At this initial step, only WFI state is supported, which is reached for both PM_SUSPEND_MEM and PM_SUSPEND_STANDBY. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-13ARM: ux500: regulators: Remove dead code for SD-card regulatorUlf Hansson2-15/+0
The signal-voltage regulator is handled through a gpio regulator configured in DT. Remove the old dead code. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-13ARM: ux500: delete U8540 UART auxdataLinus Walleij1-4/+0
The other Ux500's does not need this anymore, and the U8540 certainly is no different. Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-11ARM: clean up cache handling in platform codeNicolas Pitre1-2/+1
We have a handy macro to replace open coded __cpuc_flush_dcache_area(() and outer_clean_range() sequences. Let's use it. No functional change. Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2013-12-11ARM: add permission annotations to MT_MEMORY* mapping typesRussell King1-1/+1
Document the permissions which the various MT_MEMORY* mapping types will provide. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-12-10Merge branch 'next/cleanup' into next/dtKevin Hilman1-0/+4
2013-11-26Revert "ARM: ux500: Stop passing MMC's platform data for Device Tree boots"Linus Walleij1-4/+4
This reverts commit 49c129519a7a8840767321c38d2eaf84a263529b. The special settings for the SD/MMC card parameters that are not yet fully agreed upon how to encode into the device tree went missing with this commit. We need to first put it into the device tree, and then remove the platform data. Cc: Lee Jones <lee.jones@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26Revert "ARM: ux500: Remove AUXDATA relating to SDI (MMC) clock-name bindings"Linus Walleij1-0/+4
This reverts commit ce16feb8510cbbcd090c2320c35db2fbbffde210. This commit stopped tying down the name of the MMC/SD devices, but these names are used in the pin control table, so the MMC/SD cards stopped working. Cc: Lee Jones <lee.jones@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: decomission custom SMP TWD timer initLinus Walleij1-21/+1
Rely solely on device tree matching to detect and probe the SMP TWD timer and remove this custom hack. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: decomission the non-DT MTU init sequenceLinus Walleij1-26/+2
The MTU is now only initialized using the native clocksource device tree matching. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: Remove checking for DT during timer initLee Jones1-20/+8
Decomission the non-DT boot path as we are now DT only Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: Clean-up legacy extern prototypeLee Jones1-3/+0
Decomission io_mapping() and device init calls from non-DT boot path. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: Remove unused call to register AMBA devicesLee Jones3-30/+1
Decomission the AMBA device register functions. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: Clean-up non-DT IRQ initialisationLee Jones1-16/+6
Decommission the non-DT boot path. Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: get rid of unused headerLinus Walleij1-1/+0
This removes the unused inclusion of <linux/platform_data/pinctrl-nomadik.h> which is the last user in the entire kernel of this platform data header. Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: delete Nomadik pinctrl AUXDATALinus Walleij1-4/+0
This deletes the AUXDATA hammering down the Nomadik pin controller name to "pinctrl-db8500". We have removed all dependencies on this name. Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: delete remnant pin config macrosLinus Walleij1-23/+0
This deletes a few final pin configuration macros from the ux500. Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: move snowball pin configs to device treeLinus Walleij1-19/+0
Move the few remaining snowball pin configurations to the device tree, reference these as hogs to the pin controller until there are real devices that can make use of them. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: move snowball LED pin control to device treeLinus Walleij1-2/+0
This moves the Snowball LED pin config to the device tree. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: convert Snowball SPI pin referenceLinus Walleij1-5/+0
The SPI0 block is not at all connected to the AB8500 on the Snowball: it is connected to the external header. These pins on the header may also be used for GPIO, but let's assume that SPI is a probable usecase on the Snowball and mux in the SPI block and use these for SPI. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: move snowball ethernet config to device treeLinus Walleij1-4/+0
This transfers the muxing and biasing of the ethernet-related pins on the snowball over to the device tree. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: move HREFv60plus pin configs to device treeLinus Walleij1-53/+0
Move the few remaining HREFv60 pin configurations to the device tree, reference these as hogs to the pin controller until there are real devices that can make use of them. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26ARM: ux500: move final HREFv60 LCD pins to device treeLinus Walleij1-7/+0
Put two extra configs into the device tree to handle the default configuration of the display reset signals on the HREFv60plus, move this over from the board file to the device tree. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-04 08:16:38 +0000