| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
One more SoC change for omaps for v5.10 merge window
Remove debugfs dependency for enabling off mode during idle
for omap3 by enabling it automatically based on the PMIC
configuration.
* tag 'omap-for-v5.10/soc-part2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap3: enable off mode automatically
Link: https://lore.kernel.org/r/pull-1601445968-476435@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Two regression fixes for omaps
Fix AM33XX_IOPAD macro that broke after recent pinctrl changes
to use #pinctrl-cells = 2. And fix omap_enter_idle_coupled()
for cases where cpu_cluster_pm_enter() returns an error as
otherwise we may end up wrongly idling the MPU domain on the
next WFI.
* tag 'omap-for-v5.9/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
Link: https://lore.kernel.org/r/pull-1601544624-617679@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/fixes
Tag fix up for TI serdes mux definition introduced in 5.9
* tag 'ti-k3-dt-fixes-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (637 commits)
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
Linux 5.9-rc3
genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
fsldma: fix very broken 32-bit ppc ioread64 functionality
kernel.h: Silence sparse warning in lower_32_bits
cifs: fix check of tcon dfs in smb1
KVM: arm64: Set HCR_EL2.PTW to prevent AT taking synchronous exception
KVM: arm64: Survive synchronous exceptions caused by AT instructions
KVM: arm64: Add kvm_extable for vaxorcism code
arm64: vdso32: make vdso32 install conditional
arm64: use a common .arch preamble for inline assembly
mfd: mfd-core: Ensure disabled devices are ignored without error
usb: storage: Add unusual_uas entry for Sony PSZ drives
md/raid5: make sure stripe_size as power of two
powerpc/32s: Disable VMAP stack which CONFIG_ADB_PMU
io_uring: don't bounce block based -EAGAIN retry off task_work
io_uring: fix IOPOLL -EAGAIN retries
arm64/cpuinfo: Remove unnecessary fallthrough annotation
media: dib0700: Fix identation issue in dib8096_set_param_override()
hwmon: (gsc-hwmon) Scale temperature to millidegrees
...
Link: https://lore.kernel.org/r/20200921125402.mtwypblhb45a6ssh@akan
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enabling off mode was only reachable deeply hidden
in the debugfs. As powersaving is an important feature,
move the option out of its shady place.
The debugfs file can still be used to override the default.
Use the presence of a device compatible to ti,twl4030-idle or
ti,twl4030-idle-osc-off as an indicator that the board is wired correctly
for off mode.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: updated to fix a checkpatch warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If cpu_cluster_pm_enter() fails, we need to set MPU power domain back
to enabled to prevent the next WFI from potentially triggering an
undesired MPU power domain state change.
We already do this for omap_enter_idle_smp() but are missing it for
omap_enter_idle_coupled().
Fixes: 55be2f50336f ("ARM: OMAP2+: Handle errors for cpu_pm")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Add initial genpd support for omaps to drop more platform data
We now drop legacy platform data for RTC on am3, am4 and dra7.
And we add initial genpd support for PRM (Power and Reset Manager)
and use it to drop legacy platform data for am3 sgx and omap4/5
l4_abe interconnect instance.
* tag 'omap-for-v5.10/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for dra7 rtcss
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rtc
soc: ti: pm33xx: Simplify RTC usage to prepare to drop platform data
ARM: dts: Configure omap4 and 5 l4_abe for genpd and drop platform data
ARM: dts: Configure am3 and am4 sgx for genpd and drop platform data
soc: ti: omap-prm: Configure omap4 and 5 l4_abe power domain
soc: ti: omap-prm: Configure sgx power domain for am3 and am4
soc: ti: omap-prm: Add basic power domain support
dt-bindings: omap: Update PRM binding for genpd
Link: https://lore.kernel.org/r/pull-1599132307-761202@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
SoC changes for omaps for v5.10
Few changes to replace HTTP links with HTTPS, and a change to
delete a duplicate word for omap1 mux.h comments.
* tag 'omap-for-v5.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: mach-omap1: mux.h: delete duplicate word
ARM: OMAP2+: Replace HTTP links with HTTPS ones
ARM: OMAP2+: pm33xx-core: Replace HTTP links with HTTPS ones
ARM: OMAP2+: hwmod: Replace HTTP links with HTTPS ones
ARM: OMAP2+: Replace HTTP links with HTTPS ones
ARM: OMAP2+: PRM: Replace HTTP links with HTTPS ones
Link: https://lore.kernel.org/r/pull-1599132307-761202@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes for lockdep, tracing and RCU:
- Prevent recursion by using raw_cpu_* operations
- Fixup the interrupt state in the cpu idle code to be consistent
- Push rcu_idle_enter/exit() invocations deeper into the idle path so
that the lock operations are inside the RCU watching sections
- Move trace_cpu_idle() into generic code so it's called before RCU
goes idle.
- Handle raw_local_irq* vs. local_irq* operations correctly
- Move the tracepoints out from under the lockdep recursion handling
which turned out to be fragile and inconsistent"
* tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep,trace: Expose tracepoints
lockdep: Only trace IRQ edges
mips: Implement arch_irqs_disabled()
arm64: Implement arch_irqs_disabled()
nds32: Implement arch_irqs_disabled()
locking/lockdep: Cleanup
x86/entry: Remove unused THUNKs
cpuidle: Move trace_cpu_idle() into generic code
cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic
sched,idle,rcu: Push rcu_idle deeper into the idle path
cpuidle: Fixup IRQ state
lockdep: Use raw_cpu_*() for per-cpu variables
|
|
Remove trace_cpu_idle() from the arch_cpu_idle() implementations and
put it in the generic code, right before disabling RCU. Gets rid of
more trace_*_rcuidle() users.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Marco Elver <elver@google.com>
Link: https://lkml.kernel.org/r/20200821085348.428433395@infradead.org
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Note that we also must tag rtc as disabled on am43x-epos-evm as
it's not accessible according to commit 4321dc8dff35 ("ARM: AM43XX:
hwmod: Add rtc hwmod"). And we must keep RTC enabled for rtcwake
to work now that we've removed the custom platfor code for
re-enabling the RTC on suspend.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We must re-enable the RTC module clock enabled in RTC+DDR suspend, and
pm33xx has been using platform data callbacks for that. Looks like for
retention suspend the RTC module clock must not be re-enabled.
To remove the legacy platform data callbacks, and eventually be able to
drop the RTC legacy platform data, let's manage the RTC module clock
and register range directly in pm33xx.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can power off l4_abe domain when not in use when we configure it for
genpd. And with that change, we can now also drop the old unused legacy
platform data.
Note that we also need to now use "simple-pm-bus" instead of "simple-bus"
for PM runtime to get enabled for the bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can power off the SGX power domain when not in use when we configure
it for genpd. And with that change, we can now also drop the old unused
legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PRM controller has currently only support for resets while the power
domains are still handled in the platform code.
Let's add basic power domain support to enable and disable a PRM
controlled power domain if configured in the devicetree. This can be
used for various hardware accelerators, and interconnect instances.
Further support can be added later on as needed for runtime configuration
based on domain-idle-states.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The of_clk_get() function returns error pointers, it never returns NULL.
Fixes: 4ea3711aece4 ("ARM: OMAP2+: omap-iommu.c conversion to ti-sysc")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Patch series "mm: cleanup usage of <asm/pgalloc.h>"
Most architectures have very similar versions of pXd_alloc_one() and
pXd_free_one() for intermediate levels of page table. These patches add
generic versions of these functions in <asm-generic/pgalloc.h> and enable
use of the generic functions where appropriate.
In addition, functions declared and defined in <asm/pgalloc.h> headers are
used mostly by core mm and early mm initialization in arch and there is no
actual reason to have the <asm/pgalloc.h> included all over the place.
The first patch in this series removes unneeded includes of
<asm/pgalloc.h>
In the end it didn't work out as neatly as I hoped and moving
pXd_alloc_track() definitions to <asm-generic/pgalloc.h> would require
unnecessary changes to arches that have custom page table allocations, so
I've decided to move lib/ioremap.c to mm/ and make pgalloc-track.h local
to mm/.
This patch (of 8):
In most cases <asm/pgalloc.h> header is required only for allocations of
page table memory. Most of the .c files that include that header do not
use symbols declared in <asm/pgalloc.h> and do not require that header.
As for the other header files that used to include <asm/pgalloc.h>, it is
possible to move that include into the .c file that actually uses symbols
from <asm/pgalloc.h> and drop the include from the header file.
The process was somewhat automated using
sed -i -E '/[<"]asm\/pgalloc\.h/d' \
$(grep -L -w -f /tmp/xx \
$(git grep -E -l '[<"]asm/pgalloc\.h'))
where /tmp/xx contains all the symbols defined in
arch/*/include/asm/pgalloc.h.
[rppt@linux.ibm.com: fix powerpc warning]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Link: http://lkml.kernel.org/r/20200627143453.31835-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200627143453.31835-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix memory leak in omap_hwmod_allocate_module not freeing in
handling error path.
Fixes: 8c87970543b17("ARM: OMAP2+: Add functions to allocate module data from device tree")
Signed-off-by: Chen Tao <chentao107@huawei.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fix call iounmap for missing regs]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
[tony@atomide.com: fixed typo for am3 vs am4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When building the kernel with W=1 the build system complains of:
drivers/mmc/host/omap.c:854:6: warning: no previous prototype for ‘omap_mmc_notify_cover_event’ [-Wmissing-prototypes]
854 | void omap_mmc_notify_cover_event(struct device *dev, int num, int is_closed)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
If we move the prototype into a shared headerfile the build system
will be satisfied. Rather than create a whole new headerfile just
for this purpose, it makes sense to use the already existing
mmc-omap.h.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200701102317.235032-1-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit c31e73121f4c ("base: soc: Handle custom soc information sysfs
entries") introduced custom soc attribute group in soc_device_attribute
structure but there are no users treewide. While trying to understand
the motivation and tried to use it, it was found lot of existing custom
attributes can moved to use it instead of device_create_file.
Though most of these never remove/cleanup the custom attribute as they
never call soc_device_unregister, using these custom attribute group
eliminate the need for any cleanup as the driver infrastructure will
take care of that.
Let us remove device_create_file and start using the custom attribute
group in soc_device_attribute.
Link: https://lore.kernel.org/r/20200523170859.50003-9-sudeep.holla@arm.com
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Move device attributes to DEVICE_ATTR_RO() as that would make things
a lot more "obvious" what is happening over the existing __ATTR usage.
Link: https://lore.kernel.org/r/20200523170859.50003-8-sudeep.holla@arm.com
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Various OMAP3 boards have two AES blocks, but only one is currently
available, because the hwmods are only configured for one.
This patch migrates the hwmods for the AES engine to sysc-omap2
which allows the second AES crypto engine to become available.
omap-aes 480a6000.aes1: OMAP AES hw accel rev: 2.6
omap-aes 480a6000.aes1: will run requests pump with realtime priority
omap-aes 480c5000.aes2: OMAP AES hw accel rev: 2.6
omap-aes 480c5000.aes2: will run requests pump with realtime priority
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to disable both aes_targets on hs boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Linux 5.8-rc1
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
|
|
We must check for "dss_core" instead of "dss" to avoid also matching
also "dss_dispc". This only matters for the mixed case of data
configured in device tree but with legacy booting ti,hwmods property
still enabled.
Fixes: 8b30919a4e3c ("ARM: OMAP2+: Handle reset quirks for dynamically allocated modules")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is one more regression introduced by the last build fix:
arch/arm/mach-omap2/timer.c:170:6: error: attribute declaration must precede definition [-Werror,-Wignored-attributes]
void __init omap5_realtime_timer_init(void)
^
arch/arm/mach-omap2/common.h:118:20: note: previous definition is here
static inline void omap5_realtime_timer_init(void)
^
arch/arm/mach-omap2/timer.c:170:13: error: redefinition of 'omap5_realtime_timer_init'
void __init omap5_realtime_timer_init(void)
^
arch/arm/mach-omap2/common.h:118:20: note: previous definition is here
static inline void omap5_realtime_timer_init(void)
Address this by removing the now obsolete #ifdefs in that file and
just building the entire file based on the flag that controls the
omap5_realtime_timer_init function declaration.
Link: https://lore.kernel.org/r/20200529201701.521933-1-arnd@arndb.de
Fixes: d86ad463d670 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
On am437x we use also an ARM timer in addition to the dmtimer. As am437x
is not an SMP SoC, we need tick_broadcast() implemented. With the recent
dmtimer changes, Arnd started to see link failures for non-SMP am437x
configuration:
kernel/time/tick-broadcast.o: in function `tick_device_uses_broadcast':
tick-broadcast.c:(.text+0x130): undefined reference to `tick_broadcast'
Let's fix the issue by reverting dmtimer related changes that started
building timer.c only for CONFIG_SOC_HAS_REALTIME_COUNTER. We still
always need timer.c built-in for omap5 and dra7 for timer_probe().
And let's also move am437x tick_broadcast() to board-generic.c as
that's where we now call timer_probe() for am437x. This way we avoid
adding back more ifdefs to timer.c.
Fixes: 2ee04b88547a ("ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
With dmtimer and 32k counter being initialized based on devicetree data,
we can just drop the old timer code.
This still leaves the omap5 and dra7 realtime_counter_init() that
depend on the smc calls and control module platform code for the dra7
quirk init.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Let's also update the dts file to use #include while at it.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Note that for ti81xx, also timer1 is of type 2 unlike on am335x
where timer1 is type1 while the rest of the timers are type 2.
Cc: devicetree@vger.kernel.org
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Let's also update the dts file to use #include while at it.
Cc: devicetree@vger.kernel.org
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Note that similar to omap_init_time_of(), we now need to call
omap_clk_init() also from omap5_realtime_timer_init().
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
