| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().
For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.
The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.
This is in preparation of OMAP moving to CCF.
Based on initial changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This is a alternative to "HACK: OMAP: DSS2: VENC: disable VENC on OMAP4 to
prevent crash" (ba02fa37de) by Tomi Valkeinen <tomi.valkeinen@ti.com> to prevent
VENC from crashing OMAP4 kernel. This prevents OMAPDSS from initial registration
of a device for VENC on OMAP4.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The dispc_disable_outputs() function currently disables all LCD managers except
LCD3. This patch adds disabling functionality for LCD3 manager thereby
maintaining consistency of Display Subsystem for in case Display Controller is
reset when LCD3 manager is in use.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.
One such crash was reported by John Stultz <johnstul@us.ibm.com>:
[ 18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[ 18.765319] pgd = ea6b8000
[ 18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[ 18.774749] Internal error: Oops: 17 [#1] SMP ARM
[ 18.779663] Modules linked in:
[ 18.782836] CPU: 0 Not tainted (3.5.0-rc1-dirty #456)
[ 18.788482] PC is at _od_resume_noirq+0x1c/0x78
[ 18.793212] LR is at _od_resume_noirq+0x6c/0x78
[ 18.797943] pc : [<c00307ec>] lr : [<c003083c>] psr: 20000113
[ 18.797943] sp : ec3abe80 ip : ec3abdb8 fp : 00000006
[ 18.809936] r10: ec1148b8 r9 : c08a48f0 r8 : c00307d0
[ 18.815368] r7 : 00000000 r6 : 00000000 r5 : ec114800 r4 :
ec114808
[ 18.822174] r3 : 00000000 r2 : 00000000 r1 : ec154fe8 r0 :
00000006
[ 18.829010] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 18.836456] Control: 10c5387d Table: aa6b804a DAC: 00000015
[ 18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[ 18.848358] Stack: (0xec3abe80 to 0xec3ac000)
DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
|
|
Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.
With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.
To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.
This patch modifies arch/arm/mach-omap2/display.c to create platform
devices for DPI and SDI, and later patches will implement driver for
them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Instead of using omap_device_build() to create the omap_devices for DSS
hwmods, create them with a custom function. This will allow us to create
a parent-child hierarchy for the devices so that the omapdss_core device
is parent for the rest of the dss hwmod devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:
- Remove struct omap_display_platform_data. It was used just as a
wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
dss hwmods do not need the platform data. This should also work better
for DT, as we can create omapdss device programmatically in generic omap
boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
|
|
|
|
Commit d1589f0912533e6cb2ac8fd6f1feb3d5989fe8cb (ARM: OMAP2+: Mark
omap_hsmmc_init and omap_mux related functions as __init) changed DSI
muxing functions to __init. This doesn't work, as the muxing functions
are used every time a DSI display is enabled or disabled.
This patch removes the __inits from DSI mux functions that were
accidentally marked as __init, and makes omap4_hdmi_mux_pads __init
like it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: update comments, mark omap4_hdmi_mux_pads __init]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Now that omap hsmmc init is split into two functions, it's safe
to mark omap_hsmmc_init and omap_mux related functions to __init.
This basically reverts the following fixes for the case where
TWL was compiled as a module:
a98f77b (ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup())
8930b4e (ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c)
Additionally it fixes up the remaining section warnings for
all callers of omap_mux functions.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
|
|
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
|
|
Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
changes
ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
bootloader
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
|
|
To fix things like this:
arch/arm/mach-omap2/usb-tusb6010.c:58: error: implicit declaration of function 'memset'
arch/arm/kernel/leds.c:40: error: implicit declaration of function 'strcspn'
arch/arm/kernel/leds.c:40: warning: incompatible implicit declaration of built-in function 'strcspn'
arch/arm/kernel/leds.c:45: error: implicit declaration of function 'strncmp'
arch/arm/kernel/leds.c:55: error: implicit declaration of function 'strlen'
arch/arm/kernel/leds.c:55: warning: incompatible implicit declaration of built-in function 'strlen'
arch/arm/mach-omap2/clockdomain.c:52: error: implicit declaration of function 'strcmp'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Omap cleanups conflicted with omap2_dss work in a nontrivial
way, this is the most logical fixup.
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-apollon.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-rx51.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Implement dsi_mux_pads for OMAP4. On enable the function enables the DSI
pins and disables pull down. On disable the function disables the pins
and enables pull down.
It is unclear from the TRM whether the pull down is active if the pins
are disabled, so this implementation may leave the pins floating when
the DSI device is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.
Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.
All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.
This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
oh_core variable is no longer used, so it and its initialization can be
removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
opt_clock_available() is no longer needed, so remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Initialize get_context_loss_count in the DSS board data to
omap_pm_get_dev_context_loss_count, so that omapdss driver can use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The function to get device's context loss count has changed from
omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()
Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.
Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.
Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Provide a function in pdata to allow dss submodules to check if a given
clock is available on a platform as an optional clock.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
(based on implementation from Senthil)
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add hwmod device names for OMAP4; this enables device build for omap4 dss
hwmod IPs.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
A new file display.c is introduced for display driver init, which adds a function
omap_display_init to do the DSS driver registration. This is the first step in moving
away registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
