| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The current operating points in the mainline kernel are out of date for
at least omap4430. Let's use the values from Motorola Mapphone Linux
Android kernel as presumably those have been verified.
Note that these are only used by voltage controller, they do not enable
any new operating points for cpufreq. Looking at the recent omap3 cpufreq
related patches posted, that's a totally separate series of patches.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These registers are part of the wkup domain and are lost during RTC only
suspend and also hibernation, so storing/restoring their state is
necessary.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap4_ctrl_pad_readl/writel are no longer used by anybody, so remove
these. Syscon / pinctrl should be used to access the padconf area
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This shall not be used anymore, as control module driver is converted
into using regmap.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
There is no need to provide the control module base address through a
low-level API from the low-level IO init, as this information is
available through DT. This patch adds a new API to initialize the
control module though, but mostly makes the old API obsolete. The
old API can be completely removed once OMAP3 is made DT only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Splits the clock related provider module inits under their own driver files.
Previously this was done for all modules under the common PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"Here's a small collection of fixes accrued during the last release
that weren't considered severe enough to merge during the -rc series.
A few of these are around resurrecting TI81xx support that's been
broken for quite a while, the rest are smaller fixes -- most for PXA
but a few across the board.
There are also some updates to MAINTAINERS here, in particular for
Broadcom platforms"
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
MAINTAINERS: fix git repositories for Broadcom SoCs
ARM: pxa: fix broken isa interrupts for zeus and viper
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3
ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken
ARM: AM43xx: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: print error if wait_target_ready() failed
MAINTAINERS: add maintainer for OMAP hwmod data
ARM: OMAP2+: Disable omap3 PM init for ti81xx
ARM: OMAP2+: Fix reboot for 81xx
ARM: OMAP2+: Fix dm814 and dm816 for clocks and timer init
ARM: OMAP2+: Fix ti81xx class type
ARM: OMAP2+: Fix ti81xx devtype
ARM: OMAP2+: Fix error handling for omap2_clk_enable_init_clocks
MAINTAINERS: add a git entry for BMIPS-based BCM7xxx SoCs
MAINTAINERS: add a git entry for BCM7xxx ARM-based SoCs
MAINTAINERS: update Broadcom Cygnus SoC git tree
MAINTAINERS: move BCM63xx ARM-based SoCs git tree
hx4700: regulator: declare full constraints
ARM: pxa: add regulator_has_full_constraints to spitz board file
ARM: pxa: add regulator_has_full_constraints to poodle board file
...
|
|
Otherwise we get error "Cannot detect omap type!" and many
things can fail with following:
Unhandled fault: imprecise external abort (0xc06) at 0xc6031fb0
This is because the omap_type is being used to set up th SoC
specific functions for omaps.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up. Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610. SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz),
but can also be 19.2 or 27MHz which result in much larger drift.
Since this is used to drive the master counter at 32.768KHz * 375 /
2 = 6.144MHz, the emulated speed for 20MHz is of by 570ppm, or about 43
seconds per day, and more than the 500ppm NTP is able to tolerate.
Checking the CTRL_CORE_BOOTSTRAP register can determine if the CPU
is using the real 32.768KHz crystal or the emulated SYSCLK1/610, and
by known that the real counter frequency can be determined and used.
The real speed is then SYSCLK1 / 610 * 375 / 2 or SYSCLK1 * 75 / 244.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
https://github.com/t-kristo/linux-pm into omap-for-v3.17/soc
|
|
The mach-omap2 directory contains full register defines for OMAP4
control module but only around 27 of those are used. There are is
a total of 1795 register defines in four files with only 27 in use.
That is pretty low usefulness ratio...
I guess alot more was used when we had omap4 board files and
mach-omap2 contained more drivers but this has now changed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This patch moves the functionality from PM core to control driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Layout of DEV_FEATURE register (offset = 0x604) is different
between TI81xx and AM33xx device, so create separate function
which will check for features available on specific AM33xx SoC
and set the flags accordingly.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
EHRPWM module requires explicit clock gating of TBCLK from control
module. Hence add TBCLK clock node in clock tree for EHRPWM modules.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[bigeasy: remove CK_AM33XX]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Fix a typo - replace regist with register.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1
The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
limits are currently pending characterization data. Currently OMAP4430 values
are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
current requirements and Phoenix Max supply on VCORE2 in the default
configuration - boards which have supply which can support this should
explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
disabled pending clock changes to support DCC feature.
[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The new common clk framework includes basic definitions for mux and
divider clocks. These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP/AM33XX clk framework
has traditionally used when accessing the register to control the
mux or divisor.
To ease this transition the masks are left intact and
the width field is simply added alongside the shift and mask data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These can now be moved to be local headers in mach-omap2.
Note that this patch removes arch/arm/plat-omap/devices.c as it
will get removed anyways with Paul Walmsley's patch
"ARM: OMAP: split OMAP1, OMAP2+ RNG device registration".
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding the OMAP5 ES1.0, 2.0 and OMAP5432 cpu revision
detection support.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-part2
Miscellaneous OMAP clock, hwmod, clockdomain, and powerdomain patches
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
arch/arm/plat-omap/include/plat/omap_hwmod.h
|
|
The register is used to configure the behaviour of the CSI-2 and CCP-2
receivers. This register is available only in OMAP3630.
The original patch was submitted by Vimarsh Zutshi.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
'omap-devel-am33xx-for-v3.6' into devel-am33xx-part2
|
|
SCM contains boot addr and boot mode registers to control
other processors on different OMAP versions. It controls the
boot address and mode for DSP based subsystems like: IVA 2.1
(OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4).
If contained within SCM registers, when a processor is
booting it uses BOOTADDR to start running the code at that
location. BOOTMOD register specifies a different set of
modes for the processor to execute when booting (from direct,
idle, self-loop, user and default).
Since there was no offset associated with OMAP4, this patch
defines it.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Define AM33XX control register, in order to allow access to
control register address space, also add CONTROL_SEC_CLK_CTRL
register offset; both are required in clock tree data,
for wdt0 and timer0 clock source select configuration.
CONTROL.SEC_CLK_CTRL register is provided to select/configure
clock input for WDT0 and TIMER0.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: added include of plat/am33xx.h to fix build break;
added AM33XX_CONTROL_STATUS bitfields that will be needed for the clock
tree; fixed some control.h whitespace problems while here]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
|
|
Determine SoC type, i.e. whether GP or HS
Note: cpu_is_34xx() is true for am33xx also. Doing
cpu_is_am33xx() check after cpu_is_34xx() will not
achieve what we want due to the above reason.
Hence cpu_is_am33xx() is done before cpu_is_34xx()
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
entry points
Upon return from off-mode, the ROM code jumps to a restore function
saved in the scratchpad. Based on SoC revision or errata, this
restore entry point is different. Current code uses some helper
functions in sleep34xx.S (get_*_restore_pointer) to get the restore
function entry point.
When returning from off-mode, this code is executed from SDRAM, so
there's no reason to use these helper functions when using the SDRAM
entry points directly would work just fine.
This patch uses ENTRY/ENDPROC to create "real" entry points for these
functions, and uses those values directly when writing the scratchpad.
Tested all three entry points
- restore_es3: 3430/n900
- restore_3630: 3630/Zoom3
- restore: 3530/Overo
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
|
|
OMAP4 has three scalable voltage domains vdd_mpu, vdd_iva
and vdd_core. This patch adds the voltage tables and other
configurable voltage processor and voltage controller
settings to control these three scalable domains in OMAP4.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch adds voltage driver support for OMAP3. The driver
allows configuring the voltage controller and voltage
processors during init and exports APIs to enable/disable
voltage processors, scale voltage and reset voltage.
The driver maintains the global voltage table on a per
VDD basis which contains the various voltages supported by the
VDD along with per voltage dependent data like smartreflex
efuse offset, errminlimit and voltage processor errorgain.
The driver also allows the voltage parameters dependent on the
PMIC to be passed from the PMIC file through an API.
The driver allows scaling of VDD voltages either through
"vc bypass method" or through "vp forceupdate method" the
choice being configurable through the board file.
This patch contains code originally in linux omap pm branch
smartreflex driver. Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman. The separation of PMIC parameters
into a separate structure which can be populated from
the PMIC file is based on the work of Lun Chang from Motorola
in an internal tree.
Signed-off-by: Thara Gopinath <thara@ti.com>
[khilman: fixed link error for OMAP2-only defconfig]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
into omap-for-linus
|
|
OMAP3_IVA_MASK should use OMAP3_IVA_SHIFT instead of OMAP3_SGX_SHIFT
Signed-off-by: Arno Steffen <arno.steffen@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c. This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.
In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code. This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
Section 4.11.4 "Device Off-Mode Sequences"
|
|
Get rid of the open-coded scratchpad write in mach-omap2/prcm.c and
replace it with an actual API, omap3_ctrl_write_boot_mode(). While
there, get rid of the gratuitous omap_writel().
There's not much documentation available for what should wind up in
the scratchpad here, so more documentation would be appreciated.
Also, at some point, we should formalize our treatment of the scratchpad;
right now, accesses to the scratchpad are not well-documented.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Using macros from existing include files for registers addresses.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Based on original patch from Vishwa.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Vishwanath BS <vishwanath.bs@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
|
