| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
|
|
<generated/ti-pm-asm-offsets.h> is only generated and included by
arch/arm/mach-omap2/, so it does not need to reside in the globally
visible include/generated/.
I renamed it to arch/arm/mach-omap2/pm-asm-offsets.h since the prefix
'ti-' is just redundant in mach-omap2/.
My main motivation of this change is to avoid the race condition for
the parallel build (-j) when CONFIG_IKHEADERS is enabled.
When it is enabled, all the headers under include/ are archived into
kernel/kheaders_data.tar.xz and exposed in the sysfs.
In the parallel build, we have no idea in which order files are built.
- If ti-pm-asm-offsets.h is built before kheaders_data.tar.xz,
the header will be included in the archive. Probably nobody will
use it, but it is harmless except that it will increase the archive
size needlessly.
- If kheaders_data.tar.xz is built before ti-pm-asm-offsets.h,
the header will not be included in the archive. However, in the next
build, the archive will be re-generated to include the newly-found
ti-pm-asm-offsets.h. This is not nice from the build system point
of view.
- If ti-pm-asm-offsets.h and kheaders_data.tar.xz are built at the
same time, the corrupted header might be included in the archive,
which does not look nice either.
This commit fixes the race.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Support has been added to the OMAP IOMMU driver to fix a boot hang
issue on OMAP remoteprocs with AMMU/Unicache, caused by an improper
AMMU/Unicache state upon initial deassertion of the processor reset.
The issue is described in detail in the next three paragraphs.
All the Cortex M3/M4 IPU processor subsystems in OMAP SoCs have a
AMMU/Unicache IP that dictates the memory attributes for addresses
seen by the processor cores. The AMMU/Unicache is configured/enabled
by the SCACHE_CONFIG.BYPASS bit - a value of 1 enables the cache and
mandates all addresses accessed by M3/M4 be defined in the AMMU. This
bit is not programmable from the host processor. The M3/M4 boot
sequence starts out with the AMMU/Unicache in disabled state, and
SYS/BIOS programs the AMMU regions and enables the Unicache during
one of its initial boot steps. This SCACHE_CONFIG.BYPASS bit is
however enabled by default whenever a RET reset is applied to the IP,
irrespective of whether it was previously enabled or not. The AMMU
registers lose their context whenever this reset is applied. The reset
is effective as long as the MMU portion of the subsystem is enabled
and clocked. This behavior is common to all the IPU and DSP subsystems
that have an AMMU/Unicache.
The IPU boot sequence involves enabling and programming the MMU, and
loading the processor and releasing the reset(s) for the processor.
The PM setup code currently sets the target state for most of the
power domains to RET. The L2 MMU can be enabled, programmed and
accessed properly just fine with the domain in hardware supervised
mode, while the power domain goes through a RET->ON->RET transition
during the programming sequence. However, the ON->RET transition
asserts a RET reset, and the SCACHE_CONFIG.BYPASS bit gets auto-set.
An AMMU fault is thrown immediately when the M3/M4 core's reset is
released since the first instruction address itself will not be
defined in any valid AMMU regions. The ON->RET transition happens
automatically on the power domain after enabling the iommu due to
the hardware supervised mode.
This patch adds and invokes the .set_pwrdm_constraint pdata ops, if
present, during the OMAP IOMMU enable and disable functions to resolve
the above boot hang issue. The ops will allow to invoke a mach-omap2
layer API pwrdm_set_next_pwrst() in a multi-arch kernel environment.
The ops also returns the current power domain state while enforcing
the constraint so that the driver can store it and use it to set back
the power domain state while releasing the constraint. The pdata ops
implementation restricts the target power domain to ON during enable,
and back to the original power domain state during disable, and thereby
eliminating the conditions for the boot issue. The implementation is
effective only when the original power domain state is either RET or
OFF, and is a no-op when it is ON or INACTIVE.
The .set_pwrdm_constraint ops need to be plugged in pdata-quirks
for the affected remote processors to be able to boot properly.
Note that the current issue is seen only on kernels with the affected
power domains programmed to enter RET. For eg., IPU1 on DRA7xx is in a
separate domain and is susceptible to this bug, while the IPU2 subsystem
is within CORE power domain, and CORE RET is not supported on this SoC.
IPUs on OMAP4 and OMAP5 are also susceptible since they are in CORE power
domain, and CORE RET is a valid power target on these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
OMAP2 depends on ARCH_MULTI_V6, which makes sure that the kernel is
compiled with -march=armv6. The compiler frontend will pass the
architecture to the assembler. There is no explicit architecture
specification necessary.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The LLVM Target parser currently does not allow to specify the security
extension as part of -march (see also LLVM Bug 40186 [0]). When trying
to use Clang with LLVM's integrated assembler, this leads to build
errors such as this:
clang-8: error: the clang compiler does not support '-Wa,-march=armv7-a+sec'
Use ".arch_extension sec" to enable the security extension in a more
portable fasion. Also make sure to use ".arch armv7-a" in case a v6/v7
multi-platform kernel is being built.
Note that this is technically not exactly the same as the old code
checked for availabilty of the security extension by calling as-instr.
However, there are already other sites which use ".arch_extension sec"
unconditionally, hence de-facto we need an assembler capable of
".arch_extension sec" already today (arch/arm/mm/proc-v7.S). The
arch extension "sec" is available since binutils 2.21 according to
its documentation [1].
[0] https://bugs.llvm.org/show_bug.cgi?id=40186
[1] https://sourceware.org/binutils/docs-2.21/as/ARM-Options.html
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
"Kbuild core:
- remove unneeded $(call cc-option,...) switches
- consolidate Clang compiler flags into CLANG_FLAGS
- announce the deprecation of SUBDIRS
- fix single target build for external module
- simplify the dependencies of 'prepare' stage targets
- allow fixdep to directly write to .*.cmd files
- simplify dependency generation for CONFIG_TRIM_UNUSED_KSYMS
- change if_changed_rule to accept multi-line recipe
- move .SECONDARY special target to scripts/Kbuild.include
- remove redundant 'set -e'
- improve parallel execution for CONFIG_HEADERS_CHECK
- misc cleanups
Treewide fixes and cleanups
- set Clang flags correctly for PowerPC boot images
- fix UML build error with CONFIG_GCC_PLUGINS
- remove unneeded patterns from .gitignore files
- refactor firmware/Makefile
- remove unneeded rules for *offsets.s
- avoid unneeded regeneration of intermediate .s files
- clean up ./Kbuild
Modpost:
- remove unused -M, -K options
- fix false positive warnings about section mismatch
- use simple devtable lookup instead of linker magic
- misc cleanups
Coccinelle:
- relax boolinit.cocci checks for overall consistency
- fix warning messages of boolinit.cocci
Other tools:
- improve -dirty check of scripts/setlocalversion
- add a tool to generate compile_commands.json from .*.cmd files"
* tag 'kbuild-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (51 commits)
kbuild: remove unused cmd_gentimeconst
kbuild: remove $(obj)/ prefixes in ./Kbuild
treewide: add intermediate .s files to targets
treewide: remove explicit rules for *offsets.s
firmware: refactor firmware/Makefile
firmware: remove unnecessary patterns from .gitignore
scripts: remove unnecessary ihex2fw and check-lc_ctypes from .gitignore
um: remove unused filechk_gen_header in Makefile
scripts: add a tool to produce a compile_commands.json file
kbuild: add -Werror=implicit-int flag unconditionally
kbuild: add -Werror=strict-prototypes flag unconditionally
kbuild: add -fno-PIE flag unconditionally
scripts: coccinelle: Correct warning message
scripts: coccinelle: only suggest true/false in files that already use them
kbuild: handle part-of-module correctly for *.ll and *.symtypes
kbuild: refactor part-of-module
kbuild: refactor quiet_modtag
kbuild: remove redundant quiet_modtag for $(obj-m)
kbuild: refactor Makefile.asm-generic
user/Makefile: Fix typo and capitalization in comment section
...
|
|
Avoid unneeded recreation of these in the incremental build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These explicit rules are unneeded because scripts/Makefile.build
provides a pattern rule to create %.s from %.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The MCBSP config option has been changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
ti-sysc driver related changes for omap variants
This series improves the ti-sysc interconnect target module driver to
the point where a most of SoC can be booted with interconnect target
module data configured in device tree instead of legacy platform data.
The related device tree changes need some more work though, and can
wait for v4.19. Also some drivers using nested interconnects like DSS
need more work.
We can now remove the unused pm-noop code that is not doing anything
any longer. And we can now initialize things for PM and display pdata
later to prepare things for using ti-sysc driver.
We also need to add some more quirk handling so we can boot both with
platform data and dts data.
* tag 'omap-for-v4.18/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Show module information for suspend if DEBUG is enabled
bus: ti-sysc: Tag sdio and wdt with legacy mode for suspend
bus: ti-sysc: Detect UARTs for SYSC_QUIRK_LEGACY_IDLE quirk on omap4
bus: ti-sysc: Detect omap4 type timers for quirk
bus: ti-sysc: Add initial support for external resets
bus: ti-sysc: Improve suspend and resume handling
bus: ti-sysc: Tag some modules resource providers for noirq suspend
bus: ti-sysc: Add handling for clkctrl opt clocks
bus: ti-sysc: Make child clock alias handling more generic
bus: ti-sysc: Handle simple-bus for nested children
ARM: OMAP2+: Make display related init into device_initcall
ARM: OMAP2+: Initialize SoC PM later
ARM: OMAP2+: Only probe SDMA via ti-sysc if configured in dts
ARM: OMAP2+: Use signed value for sysc register offsets
ARM: OMAP2+: Allow using ti-sysc for system timers
ARM: OMAP2+: Drop unused pm-noop
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The sleep33xx and sleep43xx files should not depend on a header file
generated in drivers/memory. Remove this dependency and instead allow
both drivers/memory and arch/arm/mach-omap2 to generate all macros
needed in headers local to their own paths.
This fixes an issue where the build fail will when using O= to set a
split object directory and arch/arm/mach-omap2 is built before
drivers/memory with the following error:
.../drivers/memory/emif-asm-offsets.c:1:0: fatal error: can't open
drivers/memory/emif-asm-offsets.s for writing: No such file or directory
compilation terminated.
Fixes: 41d9d44d7258 ("ARM: OMAP2+: pm33xx-core: Add platform code needed for PM")
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like these functions don't do anything in the mainline kernel so
we can just drop it.
Note that we must now also remove ir-rx51 pdata as it relies on the dummy
platform data that does not do anything. And ir-rx51 is calling a pdata
callback that doesn't do anything without checking if it exists first.
For configuring device specific minimal latencies, the interface to use
is pm_qos_add_request(). For an example, see what was done in commit
9834ffd1ecc3 ("ASoC: omap-mcbsp: Add PM QoS support for McBSP to prevent
glitches"). I've added some comments to ir-rx51 so people using it can
add pm_qos support and test it.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most of the PM code needed for am335x and am437x can be moved into a
module under drivers but some core code must remain in mach-omap2 at the
moment. This includes some internal clockdomain APIs and low-level ARM
APIs which are also not exported for use by modules.
Implement a few functions that handle these low-level platform
operations can be passed to the pm33xx module through the use of
platform data.
In addition to this, to be able to share data structures between C and
the sleep33xx and sleep43xx assembly code, we can automatically generate
all of the C struct member offsets and sizes as macros by processing
pm-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Finally, add amx3_common_pm_init to create a dummy platform_device for
pm33xx so that our soon to be introduced pm33xx module can probe on
am335x and am437x platforms to enable basic suspend to mem and standby
support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As OneNAND driver is now using devicetree gpmc-onenand and its
platform data is unused and can be removed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With all of mach-omap2 booting now in device tree only mode,
we can get the module IO range from device tree and just drop
the legacy hwmod struct omap_hwmod_addr_space.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The omapdrm platform device is unused, as a replacement is now
registered in the omapdss driver. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Note that the volt_data is still being used.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This code is no longer used and can be removed as we
are using device tree.
Removing this code also removes a dependency between
drivers/mtd and arch/arm/mach-omap2 making furhter driver
changes easier.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[tony@atomide.com: removed from header too, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
OMAP2+ GPOs are initialized now using device tree, so legacy gpio
initialization code can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Legacy platform_data removal for omaps for v4.10 merge window.
We've dropped the last legacy boot board-*.c files for mach-omap2
for v4.9 so now we can start removing the unused platform_data.
All of the below has been unused since v4.9 merge window:
- Drop legacy pmic init code
- Apply seq_puts() fixes for legacy mux code, then drop it
- Drop legacy serial init
- Drop legacy i2c init
- Drop legacy PM init
- Drop legacy twl4030 platform init
- Drop legacy USB host init
- Drop legacy muxing for tusb6010, n8x0 is still using it's
platform init via pdata-quirks.c
- Drop legacy musb init
- Drop hwmod related legacy mux code
- Drop legacy hwmod data for omap3
- Drop legacy smsc911x and smc91x init
- Drop legacy board flash init
- Drop legacy ads7846 init
- Drop legacy sdram timings
* tag 'omap-for-v4.10/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP2+: Drop legacy sdram timings
ARM: OMAP2+: Drop legacy ads7846 init
ARM: OMAP2+: Remove legacy board-flash.c
ARM: OMAP2+: Remove legacy smsc911x and smc91x GPMC support
ARM: OMAP2+: Remove legacy data from hwmod for omap3
ARM: OMAP2+: Remove legacy mux code
ARM: OMAP2+: Remove legacy hwmod mux code
ARM: OMAP2+: Remove legacy usb-musb.c platform init code
ARM: OMAP2+: Remove legacy muxing for usb-tusb6010.c
ARM: OMAP2+: Remove legacy usb-host.c platform init code
ARM: OMAP2+: Remove legacy twl4030 platform init code
ARM: OMAP2+: Remove legacy PM init
ARM: OMAP2+: Remove legacy i2c.c platform init code
ARM: OMAP2+: Remove legacy serial.c
ARM: OMAP2+: mux: Use seq_putc() in omap_mux_dbg_signal_show()
ARM: OMAP2+: mux: Replace three seq_printf() calls by seq_puts()
ARM: OMAP: kill omap_pmic_init
ARM: OMAP2: kill omap2_pmic_init
ARM: OMAP3: kill omap3_pmic_init
ARM: OMAP3: kill omap3_pmic_get_config and twl_{get,set}_voltage
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
Legacy board files in mach-omap2 used the helper functions
board_{nor,nand,onenand}_init() to initialize the flash
devices attached to the GPMC.
With Device Tree booting the initialization is handled by
the GPMC driver gpmc_probe_*_child() functions so this
code is not needed anymore now that OMAP2+ is DT-only.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When connecting an ethernet chip to the GPMC, such as smc91x
or smsc911x, a GPIO has to be requested to be used as an IRQ
and also the IO memory for a GPMC chip-select.
When booting with DT the chip-select allocation is handled
in a generic manner in the GPMC driver and the GPIO to IRQ
mapping is made by the DT core so this code is not needed
anymore now that mach-omap2 related boards are DT-only.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
All the boards booting with device tree use
drivers/pinctrl-single.c instead.
Note that mach-omap1 is still using the legacy mux,
so let's move the related Kconfig options from plat-omap
to mach-omap1.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is no longer needed when booted with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This is no longer needed when booted with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This code is no longer used and can be removed as we
are using device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now initialize the UARTs using device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
It's CONFIG_SOC_OMAP5, not CONFIG_ARCH_OMAP5. Looks like make randconfig
builds have not hit this one yet.
Fixes: b3bf289c1c45 ("ARM: OMAP2+: Fix build with CONFIG_SMP and CONFIG_PM
is not set")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "drop last omap3 board files for v4.8" from Tony Lindgren:
Remove the last two legacy board-*.c files for omap3 for legacy
booting for v4.8 to allow making mach-omap2 device tree only for
v4.9.
We've had Nokia N900 and omap3 LDP board-*.c files remaining
while other omap3 devices have been device tree only for quite
a while now. Also N900 and LDP have had device tree based booting
working for years now, but few drivers for N900 were still only
working in legacy only mode until recently. With the remaining
issues out of the way, we discussed on the mailing lists that
we're finally OK to remove the remaining board-*.c files.
For the timing of this pull request, I wanted to wait until
v4.8-rc1 is out to make sure the legacy booting still works fine
after the merge window before doing it.
And for v4.8, let's not touch any other platform data in case we
still need to revert for some reason. This makes the revert just a
question of adding back the legacy board-*.c files.
Then if no issues, we can remove the unused remaining platform
data later on for v4.9.
* tag 'omap-for-v4.8/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy board file for LDP
ARM: OMAP2+: Drop legacy board file for n900
|
|
Let's drop the last two remaining omap3 legacy boot board files.
Let's only use the device tree based booting known to work for
these two boards.
We still have two omap3 boards booting in legacy mode in addition
to device tree based booting. All the other ten or so omap2+ SoCs
have been booting using device tree mode only for years now. This
has allowed us to get rid of quite a bit of arch/arm/mach-omap2
related platform init code in favor of dts and driver changes.
Pretty much the only remaining known users for omap3 legacy boot
board files are Kevin's and Russell's boot test systems, and N900
kernel tree maintained by Pali and Ivaylo. And all of them are
also supporting the device tree based booting. The legacy booting
mode has been kept around mostly to verify against regressions.
As there is still a slim chance of possible other uses of the
mainline kernel for these boards, let's just drop the board
files for v4.8, and let's not touch the related platform init
code until around v4.9 time if no issues are found. This makes
it trivial for us to add back the board files with a simple revert.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's drop the last two remaining omap3 legacy boot board files.
Let's only use the device tree based booting known to work for
these two boards.
We still have two omap3 boards booting in legacy mode in addition
to device tree based booting. All the other ten or so omap2+ SoCs
have been booting using device tree mode only for years now. This
has allowed us to get rid of quite a bit of arch/arm/mach-omap2
related platform init code in favor of dts and driver changes.
Pretty much the only remaining known users for omap3 legacy boot
board files are Kevin's and Russell's boot test systems, and N900
kernel tree maintained by Pali and Ivaylo. And all of them are
also supporting the device tree based booting. The legacy booting
mode has been kept around mostly to verify against regressions.
As there is still a slim chance of possible other uses of the
mainline kernel for these boards, let's just drop the board
files for v4.8, and let's not touch the related platform init
code until around v4.9 time if no issues are found. This makes
it trivial for us to add back the board files with a simple revert.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
I found one more make randconfig build error with the recent
SMP kexec changes. We need the mpuss now always available early.
Fixes: 0573b957fc21 ("ARM: OMAP4+: Prevent CPU1 related hang
with kexec")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.
This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.
Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The directory arch/arm/mach-omap2 is only selected for compilation if
CONFIG_ARCH_OMAP2PLUS is selected. CONFIG_ARCH_OMAP2PLUS itself is a
silent option and all machines selecting this option are multiplatform
devices. As a consequence checks for CONFIG_ARCH_MULTIPLATFORM as well
as CONFIG_ARCH_OMAP2PLUS within that directory are superfluous and can
be removed.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The legacy-style IOMMU device creation is maintained currently only
for OMAP3 SoC, as all other SoCs are DT-boot only, and also to ensure
functionality of the OMAP3 ISP driver, the only in-kernel client user
on OMAP3 that supported both modes.
Commit 78c66fbcec71 ("[media] v4l: omap3isp: Drop platform data support")
removed the legacy device support from the OMAP3 ISP driver, so the
legacy device instantiation of OMAP IOMMU devices is no longer
needed, and is cleaned up.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to remove also the Makefile entry]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove the OMAP3 core DPLL re-program code, and the associated SRAM
code that does the low-level programming of the DPLL divider, idling
of the SDRAM etc.
This code was never fully implemented in the kernel; things missing
were driver side handling of core clock changes (they need to account
for their functional clock rate being changed on-the-fly), and the whole
framework required for handling this. Thus, there is not much point
to keep carrying the low-level support code either.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A large cleanup branch this release, with a healthy 10k negative line
delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP, and
the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- a series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
ARM/fb: ep93xx: switch framebuffer to use modedb only
ARM: gemini: Setup timer3 as free running timer
ARM: gemini: Use timer1 for clockevent
ARM: gemini: Add missing register definitions for gemini timer
ARM: ep93xx/timer: Migrate to new 'set-state' interface
ARM: nomadik: push accelerometer down to boards
ARM: nomadik: move l2x0 setup to device tree
ARM: nomadik: selectively enable UART0 on boards
ARM: nomadik: move hog code to use DT hogs
ARM: shmobile: Fix mismerges
ARM: ux500: simplify secondary CPU boot
ARM: SAMSUNG: remove keypad-core header in plat-samsung
ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
ARM: SAMSUNG: local backlight header in mach-s3c64xx
ARM: SAMSUNG: local ata-core header in mach-s3c64xx
ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
ARM: SAMSUNG: local spi-core header in mach-s3c24xx
ARM: SAMSUNG: local nand-core header in mach-s3c24xx
...
|
|
into clk-next
From Tero Kristo:
"This pull request contains the TI clock driver set to move the
clock implementations under clock driver. Some small portions of
the clock driver code still remain under mach-omap2 after this,
it should be decided whether this code is now obsolete and should
be deleted or should someone try to fix it."
Slight merge conflicts with determine_rate prototype changes.
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP IOMMU driver has been adapted to the IOMMU framework
for a while now, and it no longer supports being built as a
module. Cleanup all the module related references both from
the code and in the build.
While at it, also relocate a comment around the initcall to
avoid a checkpatch strict warning about using a blank line
after function/struct/union/enum declarations.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
- hwspinlock core DT support from Suman Anna
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
* tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: qcom: Correct msb in regmap_field
DT: hwspinlock: add the CSR atlas7 hwspinlock bindings document
hwspinlock: add a CSR atlas7 driver
hwspinlock: qcom: Add support for Qualcomm HW Mutex block
DT: hwspinlock: Add binding documentation for Qualcomm hwmutex
hwspinlock/omap: add support for dt nodes
Documentation: dt: add the omap hwspinlock bindings document
hwspinlock/core: add device tree support
Documentation: dt: add common bindings for hwspinlock
|
|
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
