summaryrefslogtreecommitdiffstats
path: root/arch/arm/common/locomo.c
AgeCommit message (Collapse)AuthorFilesLines
2011-03-29arm: Fold irq_set_chip/irq_set_handlerThomas Gleixner1-2/+1
Use irq_set_chip_and_handler() instead. Converted with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-03-29arm: Reorder irq_set_ function callsThomas Gleixner1-1/+1
Reorder irq_set_chip() irq_set_chip_data() irq_set_handler() to irq_set_chip() irq_set_handler() irq_set_chip_data() so the next patch can combine irq_set_chip() and irq_set_handler() to irq_set_chip_and_handler(). Automated conversion with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-03-29arm: Cleanup the irq namespaceThomas Gleixner1-9/+9
Convert to the new function names. Automated with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-01-13ARM: LoCoMo: irq_data conversion.Lennert Buytenhek1-12/+12
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
2010-03-22[ARM] locomo: fix unpaired spin_lock_irqsaveH Hartley Sweeten1-3/+3
The function locomo_m62332_senddata sends a three byte i2c message to a M62332 DAC. This entire function is guarded with a spin_lock_irqsave at the start of the function and a spin_unlock_irqrestore at the end. As each byte is transferred, the i2c ACK from the DAC is checked. Currently, if the ACK is missing the function simply returns without the unlock. It also leaves the i2c bus in an invalid state since the last byte transferred did not have a "stop" condition and leave the bus idle. Fix this by adding an exit path using goto. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-03-22[ARM] locomo: fix SPI register offsetH Hartley Sweeten1-2/+2
The locomo spi registers are all defined in locomo.h as offsets from the first spi register LOCOMO_SPI (0x60), which is itself an offset from the locomo base address. To correctly access these registers LOCOMO_SPI must always be included in the address calculation. There are two places in locomo.c where this is not done. The first one, in locomo_suspend, actually results in a write to LOCOMO_ST instead of LOCOMO_SPICT. The second is in __locomo_probe and results in a write to LOCOMO_MCSX2 instead of LOCOMO_SPIIE. Fix these by including LOCOMO_SPI in the calculation. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-03-02[ARM] locomo: allow cascaded IRQ base to be specified by platformsEric Miao1-23/+30
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-03-02[ARM] locomo: remove unused IRQs and avoid unnecessary cascadeEric Miao1-262/+6
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*. IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as IRQ_LOCOMO_KEY. IRQ_LOCOMO_GPIO and the demultiplex handler should really be living somewhere else. Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2010-03-02[ARM] locomo: avoid unnecessary cascaded keyboard IRQEric Miao1-57/+6
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced locomokbd_{open,close} for masking/unmasking of the keyboard IRQ. Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-09-21ARM: 5711/1: locomo.c: CodingStyle cleanupsHartley Sweeten1-10/+7
EXPORT* macros should follow immediately after the closing function brace line. The prototype for locomo_chip_driver() is not needed since the static (inline) function is located earlier in the file. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-02[ARM] locomo: export locomo_frontlight_set()Eric Miao1-0/+1
This symbol is required by locomo backlight driver, exporting this allows the driver to be built as a module. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-10-09Merge branch 'pxa-all' into develRussell King1-18/+8
Conflicts: arch/arm/mach-pxa/Kconfig arch/arm/mach-pxa/corgi.c arch/arm/mach-pxa/include/mach/hardware.h arch/arm/mach-pxa/spitz.c
2008-10-09[ARM] 5298/1: Drop desc_handle_irq()Dmitry Baryshkov1-18/+8
desc_handle_irq() was declared as obsolete since long ago. Replace it with generic_handle_irq() Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-06[ARM] Convert asm/io.h to linux/io.hRussell King1-1/+1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/machRussell King1-1/+1
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07[ARM] Remove asm/hardware.h, use asm/arch/hardware.h insteadRussell King1-1/+1
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-27[ARM] 5179/1: Replace obsolete IRQT_* and __IRQT_* values with IRQ_TYPE_*Dmitry Baryshkov1-5/+5
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1]. Remove them completely. Sed script for the reference: s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g s/IRQT_PROBE/IRQ_TYPE_PROBE/g s/IRQT_NOEDGE/IRQ_TYPE_NONE/g Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-07-21arm: bus_id -> dev_name() and dev_set_name() conversionsKay Sievers1-1/+1
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-05-17[ARM] 5026/1: locomo: add .settype for gpio and several small fixesThomas Kunze1-18/+48
irqs.h: * rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND locomo.h: * add some definition for locomo spi controller * correct some errors locomo.c: * correct some errors * add set_type for locomo gpio irq chip Signed-off-by: Thomas Kunze <thommycheck@gmx.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-07-11PM: do not use saved_state from struct dev_pm_info on ARMRafael J. Wysocki1-3/+8
The saved_state member of 'struct dev_pm_info' that's going to be removed is used in arch/arm/common/locomo.c, arch/arm/common/sa1111.c and arch/arm/mach-sa1100/neponset.c. Change the code in there to use local variables for saving the state of devices during suspend. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Greg KH <greg@kroah.com> Cc: David Brownell <david-b@pacbell.net> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-11-30[ARM] Remove compatibility layer for ARM irqsRussell King1-42/+42
set_irq_chipdata -> set_irq_chip_data get_irq_chipdata -> get_irq_chip_data do_level_IRQ -> handle_level_irq do_edge_IRQ -> handle_edge_irq do_simple_IRQ -> handle_simple_irq irqdesc -> irq_desc irqchip -> irq_chip Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-06Initial blind fixup for arm for irq changesLinus Torvalds1-15/+10
Untested, but this should fix up the bulk of the totally mechanical issues, and should make the actual detail fixing easier. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-27[ARM] 3863/1: Add Locomo SPI DeviceDirk Opfer1-11/+18
The Locomo chip has a SPI interface which is used for SD/MMC cards (only collie). This patch adds the definition for the SPI device inside the Locomo chip. Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-09-27[ARM] 3847/2: Convert LOMOMO to use struct device for GPIOsRichard Purdie1-10/+22
Convert LOMOMO to use struct device * for GPIOs instead of struct locomo_dev. This enables access to the GPIOs from code which is not a locomo device itself (such as audio). Access for gpio 31 is removed for error handling (no such hardware exists). Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-08-01[ARM] 3739/1: genirq updates: irq_chip, add and use irq_chip.nameDavid Brownell1-5/+10
Patch from David Brownell ARM genirq cleanups/updates: - Start switching platforms to newer APIs * use "irq_chip" name, not "irqchip" * providing irq_chip.name - Show irq_chip.name in /proc/interrupts, like on x86. This update a bit more than half of the ARM code. The irq_chip.name values were chosen to match docs (if I have them) or be otherwise obvious ("FPGA", "CPLD", or matching the code). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-11[ARM] 3721/1: Small cleanup for locomo.cPavel Machek1-2/+1
Patch from Pavel Machek Cleanup locomo.c. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel1-1/+0
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-26[PATCH] backlight: LOCOMO Backlight Driver updatesRichard Purdie1-20/+25
Add backlight intensity control to the LOCOMO lcd/backlight driver using the backlight class and add basic power management support. This is a reimplementation and improvement of patches by John Lenz and Pavel Machek Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Antonino Daplas <adaplas@pol.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-21[ARM] Convert kmalloc+memset to kzallocRussell King1-5/+2
Convert all uses of kmalloc followed by memset to use kzalloc instead. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-21[ARM] Rename chipdata to 'base' and make it an iomem pointerRussell King1-21/+21
In all current use cases, "chipdata" is used to store an iomem address. Mark it with __iomem, and rename it to 'base'. Leave the accessor macros alone. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-20[PATCH] handle errors returned by platform_get_irq*()David Vrabel1-0/+2
platform_get_irq*() now returns on -ENXIO when the resource cannot be found. Ensure all users of platform_get_irq*() handle this error appropriately. Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-15[ARM] 3357/1: enable frontlight on colliePavel Machek1-0/+21
Patch from Pavel Machek Enable frontlight during collie bootup, so that display is actually readable in anything other than bright sunlight. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13[PATCH] Add locomo bus_type probe/remove methodsRussell King1-2/+2
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-12[ARM] Fix collie for -rc1Pavel Machek1-3/+1
This fixes compilation for collie after -rc1 platform_device changes. And yes, it even boots. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-11-09[DRIVER MODEL] Convert platform drivers to use struct platform_driverRussell King1-19/+19
This allows us to eliminate the casts in the drivers, and eventually remove the use of the device_driver function pointer methods for platform device drivers. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-29Create platform_device.h to contain all the platform device details.Russell King1-1/+1
Convert everyone who uses platform_bus_type to include linux/platform_device.h. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] DRIVER MODEL: Get rid of the obsolete tri-level suspend/resume callbacksRussell King1-8/+2
In PM v1, all devices were called at SUSPEND_DISABLE level. Then all devices were called at SUSPEND_SAVE_STATE level, and finally SUSPEND_POWER_DOWN level. However, with PM v2, to maintain compatibility for platform devices, I arranged for the PM v2 suspend/resume callbacks to call the old PM v1 suspend/resume callbacks three times with each level in order so that existing drivers continued to work. Since this is obsolete infrastructure which is no longer necessary, we can remove it. Here's an (untested) patch to do exactly that. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-29[ARM] Don't include mach-types.h unnecessarilyRussell King1-1/+0
It's pointless to include mach-types.h if you're not going to use anything from it. These references were removed as a result of: grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type' Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-09-17[PATCH] Fix up some pm_message_t typesRichard Purdie1-1/+1
Fix up some pm_message_t types Signed-Off-By: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-08[ARM] Add suspend/resume support to locomo.cJohn Lenz1-0/+101
This adds low-level suspend/resume support to locomo.c. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-09-04[ARM] Wrap calls to descriptor handlersRussell King1-5/+5
This is part of Thomas Gleixner's generic IRQ patch, which converts ARM to use the generic IRQ subsystem. Here, we wrap calls to desc->handler() in an inline function, desc_handle_irq(). This reduces the size of Thomas' patch since the changes become more localised. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-09-04[ARM] Fix compilation in locomo.cPavel Machek1-7/+7
Do not access children in struct device directly, use device_for_each_child helper instead. It fixes compilation. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-04-16Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds1-0/+1058
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-06 11:57:19 +0000