summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2015-04-27ARM: dts: sun6i: csq cs908 dts cleanupHans de Goede1-23/+14
Remove the unused usb1_vbus_pin_csq908 node (vbus is always on on the cs908), and sort the remaining nodes alphabetically. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun9i: optimus: Switch to phy core regulator bindings for usb physChen-Yu Tsai1-2/+2
Since the phy core already supports specifying a regulator to handle during power up/down, it was decided to drop the regulator support in the sun9i usb phy driver. This patch switches the DT to the core bindings. This and the phy driver would be in the same release and should not be a problem as far as DT stability goes. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun9i: Enable ARM architected timer on A80Chen-Yu Tsai1-0/+10
The A80 SoC has the architected timer, but the existing firmware from Allwinner does not set CNTFRQ at all. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun8i: Enable ARM architected timer on A23Chen-Yu Tsai1-0/+10
The A23 SoC has the architected timer, but the existing firmware from Allwinner does not set CNTFRQ at all. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: hummingbird: Enable the onboard WiFi moduleChen-Yu Tsai1-0/+22
The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO. The IC also takes a power enable signal via GPIO. This is supported with the new power sequencing bindings. The WiFi module supports out-of-band interrupt signaling via GPIO, but this is not enabled yet. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: Add pinmux settings for mmc1 to dtsiChen-Yu Tsai1-0/+8
mmc1 is used to connect to the WiFi chip on the Hummingbird A31. Signed-off-by: Chen-Yu Tsai <wens@csie.org> [maxime: Changed the drive and pull values for their defines] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun7i: Add OOB irq support to boards with broadcom sdio wifiHans de Goede2-0/+16
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sunxi: Add address- and size-cells properties to the mmc ctrl nodesHans de Goede6-0/+44
Sometimes we need to specify non-probably information for sdio devices in the devicetree, this is done through child nodes addressed by the reg property, whereby the reg property refers to the sdio function number, see; Documentation/devicetree/bindings/mmc/mmc.txt This commit adds the necessary address- and size-cells properties to the mmc controller nodes in the dtsi files, so that dts files needing such a child node do not need to specify these themselves. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: hummingbird: Add AXP221 regulator nodesChen-Yu Tsai1-1/+55
This patch adds the AXP221 regulators. Only the ones directly used on the board are added. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: hummingbird: Add AXP221 PMIC device nodeChen-Yu Tsai1-0/+9
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: hummingbird: Enable P2WI controllerChen-Yu Tsai1-0/+4
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: add p2wi controller node to dtsiBoris BREZILLON1-0/+21
The p2wi controller has only one possible pinmux setting. Use it by default in the dtsi, instead of having to set it in each board's dts. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> [wens@csie.org: reformat commit title; rename p2wi pins and use as default] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: add cubietech cubieboard4Tyler Baker2-1/+101
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This device tree has been derived from the sun9i-a80-optimus.dts as they are very similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM definitions will need to be updated in the future. [1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf Signed-off-by: Tyler Baker <tyler.baker@linaro.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun7i: Add dts file for Wexler TAB7200Aleksei Mamlin2-1/+182
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sunxi: Adjust touchscreen compatible for sun5i and laterHans de Goede2-2/+2
The touchscreen controller in the A13 and later has a different temperature curve than the one in the original A10, change the compatible for the A13 and later so that the kernel will use the correct curve. Reported-by: Tong Zhang <lovewilliam@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun5i: Add new Utoo P66 boardHans de Goede2-1/+205
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips lcd screen, 512MB RAM & 4GB emmc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun5i: Add new Auxtek-t004 boardHans de Goede2-0/+152
The auxtek-t004: http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash, toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and a 2 micro-usb receptacles, one for power and one for USB OTG. The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq support for it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun5i: Add mmc2 pinmux settingsHans de Goede1-0/+9
Add A13 mmc2 pinmux settings, note these are for a 8bit bus. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun5i: Stop using different compatibles for ehci/ohci on a13 vs a10sHans de Goede3-16/+2
The A13 and the A10s use the same die (this has been confirmed by Allwinner), as such there is no need to differentiate between the ehci/ohci parts of both, the only reasons there were different allwinner,sun5i-a*-foo compatible between these 2 parts is costemetically and because we could when we still had 2 completely different dtsi files. The allwinner,sun5i-a*-foo compatible strings are not used for binding at all, the actual driver binds to the generic-?hci compatible, so we can safely remove this cosmetical difference and simplify the dtsi files. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun4i: Enable tablet keys on Chuwi V7 CW0825Hans de Goede1-0/+27
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: dts: sun6i: hummingbird: Enable IR receiverChen-Yu Tsai1-0/+6
The A31 Hummingbird has an IR receiver. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun6i: dt: Add new Mele I7 deviceMarcus Cooper2-0/+151
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM, 8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out, a TRS connector for A/V, SPDIF and IrDA. This patch adds basic support for the device, more information can be found here (http://linux-sunxi.org/Mele_I7). Signed-off-by: Marcus Cooper <codekipper@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun8i: ippo q8h v5: Convert to DT label based syntaxMaxime Ripard1-56/+54
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: pcduino3: Convert to DT label based syntaxMaxime Ripard1-106/+104
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: olinuxino micro: Convert to DT label based syntaxMaxime Ripard1-183/+181
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: olinuxino lime2: Convert to DT label based syntaxMaxime Ripard1-145/+143
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: olinuxino lime: Convert to DT label based syntaxMaxime Ripard1-94/+92
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: m3: Convert to DT label based syntaxMaxime Ripard1-90/+88
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: i12 tvbox: Convert to DT label based syntaxMaxime Ripard1-127/+125
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: hummingbird: Convert to DT label based syntaxMaxime Ripard1-193/+191
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: cubietruck: Convert to DT label based syntaxMaxime Ripard1-159/+157
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: cubieboard2: Convert to DT label based syntaxMaxime Ripard1-100/+98
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun7i: bananapi: Convert to DT label based syntaxMaxime Ripard1-132/+130
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun6i: m9: Convert to DT label based syntaxMaxime Ripard1-75/+73
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun6i: colombus: Convert to DT label based syntaxMaxime Ripard1-61/+59
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun6i: app4 evb1: Convert to DT label based syntaxMaxime Ripard1-27/+25
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a13: olinuxino: Convert to DT label based syntaxMaxime Ripard1-119/+117
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a13: olinuxino micro: Convert to DT label based syntaxMaxime Ripard1-75/+73
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a13: hsg h702: Convert to DT label based syntaxMaxime Ripard1-69/+67
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a10s: r7 tv dongle: Convert to DT label based syntaxMaxime Ripard1-67/+65
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a10s: olinuxino micro: Convert to DT label based syntaxMaxime Ripard1-158/+157
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: pcduino: Convert to DT label based syntaxMaxime Ripard1-89/+88
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: olinuxino lime: Convert to DT label based syntaxMaxime Ripard1-109/+104
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: mini xplus: Convert to DT label based syntaxMaxime Ripard1-72/+68
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: inet97fv2: Convert to DT label based syntaxMaxime Ripard1-55/+49
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: hackberry: Convert to DT label based syntaxMaxime Ripard1-102/+85
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: cubieboard: Convert to DT label based syntaxMaxime Ripard1-108/+106
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: ba10 tvbox: Convert to DT label based syntaxMaxime Ripard1-85/+83
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun4i: a1000: Convert to DT label based syntaxMaxime Ripard1-101/+99
In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27ARM: sun5i: a10s: Move to the common sun5i DTSIMaxime Ripard1-534/+48
Now that we have a common DTSI for the sun5i family, move the A10s to use it. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-09 16:57:54 +0000