| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Nokia N900 uses twl5030 instead of twl4030. It seems both chips are
basically the same except for vaux2 register. It probably didn't result
in issues so far because of missing camera support in the mainline
kernel.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:
- The arm,data-latency and arm,tag-latency properties need 3 cells to
be valid, otherwise we end up retaining the default 8-cycle latencies
which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
rid of it.
- The cache geometry override also leads to lockup and/or general
misbehaviour. Irritatingly, the manual doesn't state the actual PL310
configuration, but based on the boardfile code and poking registers
from the Boot Monitor, it would seem to be 8 sets of 16KB ways.
With that, we can successfully boot to enjoy the fun of mismatched FPUs...
Cc: stable@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
c90bb7b enabled the high speed UARTs of the Jetson TK1. Due to a merge
quirk, wrong addresses were introduced. Fix it and use the correct
addresses.
Thierry let me know, that there is another patch (b5896f67ab3c in
linux-next) in preparation which removes all the '0,' prefixes of unit
addresses on Tegra124 and is planned to go upstream in 4.8, so
this patch will get reverted then.
But for the moment, this patch is necessary to fix current misbehaviour.
Fixes: c90bb7b9b9 ("ARM: tegra: Add high speed UARTs to Jetson TK1 device tree")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Cc: stable@vger.kernel.org # v4.7
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by clocks, flash protection
and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This syscon needs to be looked up by flash protection, CLCD
display output settings and other consumers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
|
|
Pull EDAC updates from Borislav Petkov:
"This last cycle, Thor was busy adding Arria10 eth FIFO support to the
altera_edac driver along with other improvements. We have two
cleanups/fixes too.
Summary:
- Altera Arria10 ethernet FIFO buffer support (Thor Thayer)
- Minor cleanups"
* tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
ARM: dts: Add Arria10 Ethernet EDAC devicetree entry
EDAC, altera: Add Arria10 Ethernet EDAC support
EDAC, altera: Add Arria10 ECC memory init functions
Documentation: dt: socfpga: Add Arria10 Ethernet binding
EDAC, altera: Drop some ifdeffery
EDAC, altera: Add panic flag check to A10 IRQ
EDAC, altera: Check parent status for Arria10 EDAC block
EDAC, altera: Make all private data structures static
EDAC: Correct channel count limit
EDAC, amd64_edac: Init opstate at the proper time during init
EDAC, altera: Handle Arria10 SDRAM child node
EDAC, altera: Add ECC Manager IRQ controller support
Documentation: dt: socfpga: Add interrupt-controller to ecc-manager
|
|
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A quiet regulator API release, a few new drivers and some fixes but
nothing too notable. There will also be some updates for the PWM
regulator coming through the PWM tree which provide much smoother
operation when taking over an already running PWM regulator after boot
using some new PWM APIs.
Summary:
- Support for configuration of the initial suspend state from DT.
- New drivers for Mediatek MT6323, Ricoh RN5T567 and X-Powers AXP809"
* tag 'regulator-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (38 commits)
regulator: da9053/52: Fix incorrectly stated minimum and maximum voltage limits
regulator: mt6323: Constify struct regulator_ops
regulator: mt6323: Fix module description
regulator: mt6323: Add support for MT6323 regulator
regulator: Add document for MT6323 regulator
regulator: da9210: addition of device tree support
regulator: act8865: Fix missing of_node_put() in act8865_pdata_from_dt()
regulator: qcom_smd: Avoid overlapping linear voltage ranges
regulator: s2mps11: Fix the voltage linear range for s2mps15
regulator: pwm: Fix regulator ramp delay for continuous mode
regulator: da9211: add descriptions for da9212/da9214
mfd: rn5t618: Register restart handler
mfd: rn5t618: Register power off callback optionally
regulator: rn5t618: Add RN5T567 PMIC support
mfd: rn5t618: Add Ricoh RN5T567 PMIC support
ARM: dts: meson: minix-neo-x8: define PMIC as power controller
regulator: tps65218: force set power-up/down strobe to 3 for dcdc3
regulator: tps65218: Enable suspend configuration
regulator: tps65217: Enable suspend configuration
regulator: qcom_spmi: Add support for get_mode/set_mode on switches
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.8:
API:
- first part of skcipher low-level conversions
- add KPP (Key-agreement Protocol Primitives) interface.
Algorithms:
- fix IPsec/cryptd reordering issues that affects aesni
- RSA no longer does explicit leading zero removal
- add SHA3
- add DH
- add ECDH
- improve DRBG performance by not doing CTR by hand
Drivers:
- add x86 AVX2 multibuffer SHA256/512
- add POWER8 optimised crc32c
- add xts support to vmx
- add DH support to qat
- add RSA support to caam
- add Layerscape support to caam
- add SEC1 AEAD support to talitos
- improve performance by chaining requests in marvell/cesa
- add support for Araneus Alea I USB RNG
- add support for Broadcom BCM5301 RNG
- add support for Amlogic Meson RNG
- add support Broadcom NSP SoC RNG"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (180 commits)
crypto: vmx - Fix aes_p8_xts_decrypt build failure
crypto: vmx - Ignore generated files
crypto: vmx - Adding support for XTS
crypto: vmx - Adding asm subroutines for XTS
crypto: skcipher - add comment for skcipher_alg->base
crypto: testmgr - Print akcipher algorithm name
crypto: marvell - Fix wrong flag used for GFP in mv_cesa_dma_add_iv_op
crypto: nx - off by one bug in nx_of_update_msc()
crypto: rsa-pkcs1pad - fix rsa-pkcs1pad request struct
crypto: scatterwalk - Inline start/map/done
crypto: scatterwalk - Remove unnecessary BUG in scatterwalk_start
crypto: scatterwalk - Remove unnecessary advance in scatterwalk_pagedone
crypto: scatterwalk - Fix test in scatterwalk_done
crypto: api - Optimise away crypto_yield when hard preemption is on
crypto: scatterwalk - add no-copy support to copychunks
crypto: scatterwalk - Remove scatterwalk_bytes_sglen
crypto: omap - Stop using crypto scatterwalk_bytes_sglen
crypto: skcipher - Remove top-level givcipher interface
crypto: user - Remove crypto_lookup_skcipher call
crypto: cts - Convert to skcipher
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
|
|
Just several instances of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the non-standard vendor prefix stm with st for
STMicroelectronics. The drivers do not specify the vendor prefixes
since the I2C Core strips them away from the DT provided compatible
string. Therefore, changing existing device trees does not have any
impact on device detection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Fixes for v4.8" from Simon Horman:
* Corrections to r8a7792
* tag 'renesas-dt-fixes-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7792: remove ADSP clock
ARM: dts: r8a7792: add PLL1 divided by 2 clock
|
|
Merge "mvebu dt for 4.8 (part 1)" from Gregory CLEMENT:
Fix dts for the clearfog board (Armada 388 SoC based)
* tag 'mvebu-dt-4.8-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-388-clearfog: remove duplicate mdio entry
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8, take 2" from Maxime Ripard:
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
* tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (21 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: sun7i: bananapi-m1-plus: red LED is power LED
ARM: dts: sun7i: bananapi-m1-plus: Unify suffix for board specific labels
ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
ARM: dts: sun7i: lamobo-r1: Enable audio codec
ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
...
|
|
'regulator/topic/rn5t618', 'regulator/topic/tps65218' and 'regulator/topic/twl' into regulator-next
|
|
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables backlight, regulator and full otg
support. I've tested that all these works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in quite a nice cleanup for this dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a drivevbus-supply property so that the drivevbus regulator
reports the right voltage value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in a nice cleanup for this dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in quite a nice cleanup for this dts file.
Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Remove all mention of q8 from sun5i-reference-design-tablet.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Set lradc vref to the actual avcc ldo, rather then to the fixed 3v0
regulator from common-regulators.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.
Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Commit 0dfd582e026a ("watchdog: qcom: use timer devicetree
binding") moved to use the watchdog as a subset timer
register block. Some devices have the watchdog completely
standalone with slightly different register offsets as
well so let's account for the differences here.
The existing "kpss-standalone" compatible string doesn't
make it entirely clear exactly what the device is so
rename to "kpss-wdt" to reflect watchdog timer
functionality. Also update ipq4019 DTS with an SoC
specific compatible.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Update the compatible string to align with driver and also
add SoC specific string to DTS.
CC: linux-watchdog@vger.kernel.org
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Merge "DT Changes for 4.8 #3" from Alexandre Belloni:
- Lot of fixes for dtc warnings
- Separate dtb compilation for ARMv4 and ARMv5
* tag 'at91-ab-4.8-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
ARM: dts: at91: sama5d4_ma5d4evk: fix regulator names
ARM: dts: at91: sama5d4_ma5d4: fix regulator names
ARM: dts: at91: sama5d4_xplained: fix regulator names
ARM: dts: at91: sama5d3_xplained: fix regulator name
ARM: dts: at91: sama5d4ek: remove useless lcd_bus
ARM: dts: at91: Fix USB endpoint nodes
Documentation: dt: usb: atmel-usb: add unit-address
ARM: dts: at91: Fix ADC trigger nodes
Documentation: dt: iio: at91_adc: fix trigger node names
|
|
Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.
Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add a reg property in the endpoint node as documented in
Documentation/devicetree/bindings/media/video-interfaces.txt
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000/port/endpoint@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.
Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.
Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_3v3_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Remove the unit-address from the oneiwire node as it doesn't have a reg
property.
Solves:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_mmc1_reg is a fixed regulators and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@2 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a
reg property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg
property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
vcc_mmc0_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
