| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and MAINTAINERS
files):
for i in arch/arm/boot/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/boot/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/boot/dts/*[si]
done
NOTE: bootloaders that depend on older dtb names will need to be
updated as well.
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Update the compatible flags to allow specific SoC identification.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
This patch enables networking on k2e evm by adding device
bindings for netcp, knav and qmss. See device binding
documentation below for details.
Documentation/devicetree/bindings/net/keystone-netcp.txt
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Keystone K2E-EVM has two 1G Marvell 88E1514 Ethernet PHYs
installed, which are compatible with 88E1510.
Hence, add corresponding child nodes for 1G MDIO bus.
For more information see:
https://www.einfochips.com/index.php/partnerships/texas-instruments/k2e-evm.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
k2hk, k2e, k2l EVM board have the same Micron N25Q128A11
SPI NOR Flash installed on SPI0 bus.
The NOR Flash is splitted on two partistions:
partition@0
label = "u-boot-spl";
reg = <0x0 0x80000>;
partition@1
label = "misc";
reg = <0x80000 0xf80000>;
Hence, add SPI NOR Flash nodes to all k2hk, k2e, k2l EVM boards.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Add AEMIF/NAND device entry.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
I2C devices are not the part of Keystone SoC and have to be
defined in board DTS files.
Hence, move i2c0 EEPROM device node from Keystone SoC to
k2hk, k2e, k2l EVM files as they all have similar EEPROM SoCs
installed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
As suggested by Olof Johansson at
http://www.spinics.net/lists/arm-kernel/msg314009.html.
It be better just keeping a "ti,keystone" top-level compatible and
just using that to probe. If so we don't have to touch the file
for new boards in the future.
So use common "ti,keystone" compatible in keystone.c for all boards.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Keystone2 Edison (K2E) is a Quad Cortex A15 based SoC with
1 DSP. It has standard peripherals such as i2c, spi, uart, timer,
pcie, etc similar to k2hk, but without wireless hardwares. This
patch add support for k2 Edison SoC and EVM. This re-uses the common
keystone.dtsi to include common bindings across the various k2
devices.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
